ADSL Magnetics TM02395 • Designed to comply with the requirements of UL1950 and EN60950 to provide the supplementary insulation barrier with a working voltage of 250V • Minimum interwinding breakdown voltage of 1500 Vrms • Operating and storage temperature range: -40° to +85° C • Meets IEC 695, 2-2 flammability requirements • PWB Process Capability: standard printed wiring board assembly techniques, total-immersion cleaning • Reliability testing: shock, vibration, temperature cycling, temperature - humidity - bias ELECTRICAL SPECIFICATIONS AT 25° C Turns Ratio ±2% Inductance1 µH ±5% Leakage Inductance2 µH max Interwinding Capacitance3 pF max Chip : Line Line Side Chip Side Chip : Line Chip Side Line Side 20 kHz 1.1 MHz 1 : 1.15 475 5 50 2.2 2 45 Part Number S560-6600-DT Part Number S560-6600-DT DCR Ω max Longitudinal Balance4 dB min Insertion Loss4 dB max Insertion Loss4 dB max Harmonic Distortion4 dB max DC Unbalance Current mA max 150 kHz - 300 kHz 1.0 MHz 12 Vpp 150 kHz Chip : Shorted Line 0.5 1.0 -85 2 All measurements are made with pins 2 and 3 connected and pins 5 and 7 connected 1. Inductance measured at 10 kHz, 0.1 Vac 2. Measured at 100 kHz, 0.1 Vac 3. Interwinding capacitance measured at 10 kHz, 0.1 Vac 4. Measured with line impedance of 100 Ω and chip impedance of 75.6 Ω SCHEMATIC S560-6600-DT 1 8 3 5 2 7 4 6 Line Chip ©2002 Bel Fuse Inc. Specifications subject to change without notice. 01.02 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 1 ADSL Magnetics TM02395 MECHANICAL 0.061 [1.55] 4 1 S560-6600-DT 0.324 [8.23] 8 5 0.098 [2.50] 0.048 [1.22] Suggested PCB Pad Layout 0.385 [9.78] max 0.339 [8.61] max 0.450 [11.43] max 0.098 [2.50] 0.024 [0.61] 0.227 [5.77] 0.299 [7.59] Dimensions are in inches [millimeters]. Standard dimension tolerance is ±0.005 [0.13] unless otherwise noted. Tape and Reel Packaging 24 mm wide by 16 mm pitch; 13 inch OD, 4 inch ID 300 components per reel, maximum Meets ANSI/EIA 481-2 Carrier Tape Standards User Feed Direction Orientation of Component Inside Pocket ©2002 Bel Fuse Inc. Specifications subject to change without notice. 01.02 CORPORATE FAR EAST EUROPE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com Bel Fuse Ltd. 8F / 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com page 2