DIALIGHT 597-3021-5XX

3mm Round
®
Optopipe®
Optical Light Pipe, Bi-Level
515-1094
Recommended
MicroLED SMT LEDs
for use with 515-1094
DIRECTION
OF LIGHT
DIFFUSED
FRONT
SURF
ACES;
2 PLCS
5.08
[.200]
(REF)
4.57
[.18]
3.05
[.120]
Ø 3.05± .05
[.120± .002]
TYP; 2 PLCS
17.78
[.70]
(REF)
2.77
[.109]
9.14
[.36]
2.54
[.100]
1.65
[.065]
2.79
[.11]
ALIGNMENT
ONLY PIN
2.29± .18
[.090± .007]
5.08± .07
[.200± .003]
4.39
[.173]
TYP
7.62± .18
[.300 ± .007]
14.22
[.56]
6.10
[.024]
.99
[.039]
TYP
0.508
[.020]TYP
1.63
[.064]
DIA (NOM)
MNTG PI
N
5.08± .18
[.200± .007]
2.54± .18
[.100± .007]
3.81
[.150]
TYP
1.63
[.063]
TYP
4.27
[.168]
2.54±.05
[.100±.002]
PART NO.
COLOR
PAGE #
597-3021-5xx
597-3111-5xx
597-3211-5xx
597-3301-5xx
597-3401-5xx
597-7701-5xx
597-7721-5xx
Red
AlGaAs Red
Orange
Green
Yellow
Red/Green
Yellow/Green
1-30
1-30
1-30
1-30
1-30
1-31
1-31
DIRECTION
OF LIGHT
2.69
[.106]TYP
Ø 1.52±.05
[.060± .002]
TYP; 2 PLCS
4.19
[.165]
NOTE: designed for
post-reflow
PC board insertion.
3.35
[.132]
BICOLORADS
P
(P/N: 597-77X1-507)
SOLDERAD/HOLES
P
LA
YOUT
SINGLE COLOR
ADS
P
(P/N: 597-3XX1-507)
Dimensions in mm [inches]
Features
• Can be mounted in arrays spaced .200 apart (min.)
• High transmissivity polycarbonate material
• UL94V-0 compliance
• ESD protection (circuit isolation from front panel)
• Wide viewing angle
• Arrays reduce insertion costs
• Allows bi-level SMT indicators
• Secures to PCB by press-fit
LED Data
For absolute maximum ratings and other electrical and optical data on the recommended LEDs,
refer to LED data sheets.
Operating/Storage Temperature
–30°C to +100°C
Dialight Optopipe® Light Pipe Description
This Optopipe® is a standard design intended as a SMT compatible replacement for our 553 Series Circuit Board
Indicators. The light outputs are spaced vertically .100" from the PCB to the first element, and then 0.200" between the top
and bottom elements. We recommend a minimum of 0.200" between light pipes as a normal mounting pitch. This Optopipe®
is held in place by 2 press-fit pins along the bottom of the device. The light pipe is not attached to the panel at any point
but can protrude through holes in the panel. The gently arcing emitting end sticks through the plastic or metal panel. The
light source is Dialight's 597 Series Type 1208 LED. The light pipe material is water clear transmissive polycarbonate rated
UL94-V0, and has a 35% oxygen index.
Dialight can provide custom Optopipe® solutions for your applications.
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com