3 x 5mm Rectangular ® OptopipeTM Optical Light Pipe, 2 Array (RJ45 Jack) 19.05 [.750] FRONT PANEL 13.98 [.550] 5.08 [.200] 2 PLCS 2.54 [.100] 3.05 [.120] DIFFUSED FRONT SURFACE 20.57 [.81] 1.91 [.075] Recommended MicroLED SMT LEDs for use with 515-1070 31.24 [1.23] 29.0 [1.142] 3.93 [.155] 27.94 [1.100] 35.26 [1.388] .71 [.028] 1.57 [.062] 2X Ø 2.87 ±.05 [.113 ±.002] 6.99 [.275] 2.01 [.079] 27.43 [1.080] 7.62 ±.15 [.300 ±.006] 1.57 [.062] C.L. MOUNTING PIN #1 1.50 [.059] .99 [.039] 1.35 [.053] 13.98 [.550] .99 [.039] DIRECTION OF LIGHT NOTE: designed for post-reflow PC board insertion. 27.94 ±.05 [1.100 ±.002] RECOMMENDED SOLDER PAD/HOLES LAYOUT FOR BI-COLOR LEDS 2 3.56 [.140] C.L. LEDS 3.66 [.144] 515-1070 Dimensions in mm [inches] Features • Complements Dialight’s 515-1022 Four Array Optopipe Light Pipe • Allows indicators to be positioned above corresponding RJ45 jack or D-Subminiature • High transmissivity polycarbonate material • UL94V-0 compliance • ESD protection (circuit isolation from front panel) • Wide viewing angle • Arrays reduce insertion costs • Secures to PCB by press-fit PART NO. COLOR PAGE # 597-3001-1xx 597-3111-1xx 597-3111-5xx 597-3211-1xx 597-3211-5xx 597-3301-1xx 597-3301-5xx 597-3401-1xx 597-3401-5xx 597-7701-1xx 597-7701-5xx 597-7721-1xx 597-7721-5xx 597-7731-1xx Red AlGaAs Red AlGaAs Red Orange Orange Green Green Yellow Yellow Red/Green Red/Green Yellow/Green Yellow/Green Red/Yellow 1-19 1-19 1-30 1-19 1-30 1-19 1-30 1-19 1-30 1-20 1-31 1-20 1-31 1-20 LED Data For absolute maximum ratings and other electrical and optical data on the recommended LEDs, refer to LED data sheets. Operating/Storage Temperature –30°C to +100°C Dialight Optopipe Light Pipe Description This light pipe’s two 3 x 5mm rectangular light emitting surfaces appear bright and are optically well isolated. The light pipe is reliably held in place by 2 press-fit pins located at either end of the light pipe array. This Optopipe™ functions as a through-the-case indicator by conducting the light over the top of connectors or switches. A textured finish on the 2 light emitting surfaces maximizes the viewing angle. The recommended light sources are Dialight's 597 Series PLCC-2 or PLCC-4 Type SMT LEDs. The LEDs are mounted in a straight line on an 0.550" pitch. The light pipe material is water clear transmissive polycarbonate rated UL94-V0, and has a 35% oxygen index. Dialight can provide custom Optopipe™ solutions for your applications. Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com 2-25