Microwave Ceramics and Modules 2 Pole Filter for W-LAN 5GHz / [5.725–5.875] Band Filter B69842N5807A150 Preliminary Data Sheet Features z SMD filter consisting of coupled resonators with stepped impedances z MgTiO3 - CaTiO3 (εr = 21 / TCf =0±10 ppm/K) with a coating of copper (10µm) and tin (>5µm) z Excellent reflow solderability, no migration effect due to copper/tin metallization Index Page 2 z Component drawing z Recommended footprint Page 3 z Characteristics z Maximum ratings z Typical passband characteristic Page 4 z Broadband characteristic z Processing information z Soldering requirements Page 5 ISSUE DATE z Delivery mode 19.03.04 ISSUE P2 PUBLISHER SAW MWC PD PAGE 1/5 Microwave Ceramics and Modules 2 Pole Filter for W-LAN 5GHz / [5.725–5.875] Band Filter B69842N5807A150 Preliminary Data Sheet Component drawing View from below onto the solder terminals and view from beside Recommended footprint Soldered Pads. I/O Pads must be connected to 50 ohms impedance lines. ground covered with solder resist. It must be connected to groung plane below by vias Max diameter: 0.3 mm Max via pitch:1 mm ISSUE DATE 19.03.04 ISSUE P2 PUBLISHER SAW MWC PD PAGE 2/5 Microwave Ceramics and Modules 2 Pole Filter for W-LAN 5GHz / [5.725–5.875] Band Filter B69842N5807A150 Preliminary Data Sheet Characteristics min. Center frequency fc αIL B 150 Insertion loss Passband Standing wave ratio typ. max. 5.8 - GHz 1.1 1.3 dB MHz SWR 1.5 Impedance Z 50 Power Attenuation P α at DC to 1990 MHz at 3300 MHz at 5000 MHz at 5425 MHZ at 6175 MHz at 6800 MHz 2.0 Ω 1.0 55 40 40 12 8 25 W 60 46 45 15 12 27 dB dB dB dB dB dB Maximum ratings IEC climatic category (IEC 68-1) - 40/+ 90/56 Operating temperature Top -40 / + 85 °C Typical passband characteristic 0 -10 [dB] -20 S11 [dB] S21 [dB] -30 -40 -50 6,0 5,8 5,6 5,4 5,2 5,0 4,8 4,6 4,4 4,2 4,0 -60 Frequency [GHz] ISSUE DATE 19.03.04 ISSUE P2 PUBLISHER SAW MWC PD PAGE 3/5 Microwave Ceramics and Modules 2 Pole Filter for W-LAN 5GHz / [5.725–5.875] Band Filter B69842N5807A150 Preliminary Data Sheet Broadband characteristic Epcos B69842N5777A100 upperharmonics 0 -10 Att [dB] -20 -30 S21[dB] -40 -50 21,0 20,0 19,0 18,0 17,0 16,0 15,0 14,0 13,0 12,0 11,0 10,0 9,0 8,0 7,0 6,0 5,0 4,0 3,0 2,0 1,0 -60 freq [GHz] Processing information z Wettability acc. to IEC 68-2-58: ≥ 75% (after aging) Soldering requirements Profile for eutectic SnPb solder paste Profile for leadfree solder paste Soldering type reflow Maximum soldering temperature 235 (max. 2 sec.) (measuring point on top surface of the component) 225 (max. 10 sec.) reflow 260 (max. 2 sec.) °C 250 (max. 10 sec.) °C Recommended soldering conditions (infrared): within 10 sec. Temp. [°C] within 10 sec. Temp. [°C] 245°C±5°C 215°C±10°C 20-40 sec. ISSUE DATE 19.03.04 30 sec. Time [sec.] 2.5 °C/s 40-80 sec. ISSUE P2 PUBLISHER 2-3 min. SAW MWC PD Time [sec.] > - 5 °C/s PAGE 4/5 Microwave Ceramics and Modules 2 Pole Filter for W-LAN 5GHz / [5.725–5.875] Band Filter B69842N5807A150 Preliminary Data Sheet Delivery mode z Blister tape acc. to IEC 286-3, PS, grey z Pieces/tape: 4000 EPCOS AG 2001. All Rights Reserved. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. The information contained in this data sheet describes the type of component and shall not be considered as guaranteed characteristics. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers' Association), unless otherwise agreed. ISSUE DATE 19.03.04 ISSUE P2 PUBLISHER SAW MWC PD PAGE 5/5