FMA3007 Production Datasheet v3.0 2-20GHZ BROADBAND MMIC AMPLIFIER FEATURES: • • • • • • FUNCTIONAL SCHEMATIC: VG2 17 dBm Output Power 11 dB Gain pHEMT Technology Input Return Loss < -13dB Output Return Loss < -11dB Voltage Gain Control VDD RF Input RF Output VG1 GENERAL DESCRIPTION: The FMA3007 is a high performance 2-20GHz Gallium Arsenide monolithic travelling wave amplifier. It is suitable for use in broadband communication, instrumentation and electronic warfare applications. The die is fabricated using the Filtronic 0.25µm process. TYPICAL APPLICATIONS: • • • Test Instrumentation Electronic Warfare Broadband Communication Infrastructure ELECTRICAL SPECIFICATIONS: PARAMETER CONDITIONS 1, 2, 3 MIN TYP MAX UNITS Small Signal Gain 2-12GHz 9.5 10.5 11.5 dB Small Signal Gain 12-20GHz 9.5 11.5 12.5 dB Input Return Loss 2-20GHz - - -13 dB Output Return Loss 2-20GHz - - -11 dB Reverse Isolation 2-20GHz - - -27 dB Output Power at 1dB 2GHz 16 19 - dBm compression point 10GHz 18 19 - dBm 20GHz 14 16 - dBm Noise Figure 2-4.5 GHz - - 8.5 dB Noise Figure 4.5-20 GHz - 4.5 5.5 dB Drain Current For Vdd = 3.5V , Vg1 = -0.38V , Vg2=+1V 60 100 150 mA - 3.5 - V Drain Voltage Notes: 1. TAmbient = +25°C 2. Device is biased at constant gate voltage, measured on wafer with Z0 = 50Ω 3. Measurement Conditions VG1= -0.38V, VDD= 3.5V, VG2=+1V. 1 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FMA3007 Production Datasheet v3.0 ABSOLUTE MAXIMUM RATINGS: PAD REF PAD NAME DESCRIPTION PIN COORDINATES (µm) A RF in RF in (140, 1153) B VDP (+Ve) Temperature (2097, 140) PARAMETER SYMBOL ABSOLUTE MAXIMUM Max Input Power Pin +20dBm Gate Voltage VG1 -2V Drain Voltage VDD +10V Ptot tbd Gain Compression Comp tbd D GND Ground (2545, 140) Thermal Resistivity θJC 38°C/W E VG1 Gate Control (2769, 140) Operating Temp Toper -40°C to +85°C F VG2 Gain Control (2993, 140) Storage Temp Tstor -55°C to +150°C G RF Out RF Out (3004, 1141) H GND Ground (2800, 1650) I VDD Drain Voltage (2550, 1650) Total Power Dissipation Monitoring Diode C VDN (-Ve) Temperature (2321, 140) Monitoring Diode Note: Exceeding any one of these absolute maximum ratings may cause permanent damage to the device. Note: Co-ordinates are referenced from the bottom left hand corner of the die to the centre of bond pad opening PAD LAYOUT: I H A G B C D E F DIE SIZE (µm) DIE THICKNESS (µm) MIN. BOND PAD PITCH (µm) MIN. BOND PAD OPENING (µm x µm ) 3150 x 1780 100 220 100 x 100 2 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FMA3007 Production Datasheet v3.0 TYPICAL PERFORMANCE FOR ON WAFER MEASUREMENTS: Note: Measurement Conditions VG1= -0.38V, VDD= 3.5V, VG2=+1V, TAMBIENT = 25°C P1dB P 1 d B (d B m ) 20 15 10 5 0 2 4 6 8 10 12 14 16 18 20 Frequency (GHz) Gain vs VG2 Control Voltage 10 Freq = 10 GHz Gain (dB) 8 6 4 2 0 -0.5 -0.4 -0.3 -0.2 -0.1 0 Vg2(V)Voltage 0.1 0.2 0.3 0.4 3 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FMA3007 Production Datasheet v3.0 TYPICAL MEASURED PERFORMANCE FOR ON WAFER TEMPERATURE MEASUREMENTS: Note: Measurement Conditions VG1= -0.38V, VDD= 3.5V, VG2= +1V, TAMBIENT = -40°C to +85°C 4 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FMA3007 Production Datasheet v3.0 S-PARAMETERS FOR ON-WAFER MEASUREMENTS: Note: Measurement Conditions VDD= 3.5V, Vg1=-0.38V and Vg2=1V S11 S21 S12 S22 Frequency Mag Angle Mag Angle Mag Angle Mag Angle 2 0.17 7.23 3.47 -36.35 0.00 -63.41 0.02 -48.45 2.19 0.17 2.14 3.45 -42.93 0.00 -29.52 0.02 -37.80 2.38 0.16 -4.69 3.43 -48.73 0.00 72.59 0.01 -33.00 2.57 0.15 -10.51 3.42 -54.29 0.00 42.47 0.00 27.64 2.76 0.14 -15.56 3.42 -59.82 0.00 27.49 0.01 -38.27 2.95 0.13 -20.19 3.42 -65.28 0.00 13.11 0.01 -44.59 3.14 0.12 -24.56 3.42 -70.67 0.00 4.32 0.01 21.28 3.33 0.11 -28.52 3.42 -75.97 0.00 -3.76 0.01 15.31 3.52 0.11 -32.28 3.42 -81.24 0.00 -11.28 0.01 13.40 3.71 0.10 -36.00 3.41 -86.45 0.00 -17.93 0.01 13.67 3.9 0.09 -39.67 3.42 88.39 0.00 -24.95 0.01 -16.72 4.09 0.08 -43.21 3.42 83.29 0.00 -30.94 0.01 -6.18 4.28 0.08 -46.86 3.42 78.22 0.00 -40.08 0.01 -65.06 4.47 0.07 -50.51 3.42 73.16 0.00 -45.92 0.02 -53.62 4.66 0.06 -53.98 3.43 68.10 0.00 -50.32 0.02 -44.57 4.85 0.05 -57.63 3.43 63.07 0.00 -56.49 0.02 -39.29 5.04 0.05 -60.76 3.44 58.02 0.00 -63.05 0.03 -37.33 5.23 0.04 -63.54 3.44 52.99 0.00 -67.95 0.04 -37.85 5.42 0.03 -66.22 3.45 47.95 0.00 -74.11 0.04 -39.95 5.61 0.02 -68.53 3.46 42.91 0.00 -79.14 0.05 -42.71 5.8 0.02 -68.00 3.47 37.87 0.00 -83.92 0.06 -45.73 5.99 0.01 -64.51 3.48 32.78 0.01 18.48 0.07 -49.38 6.18 0.00 -42.62 3.48 27.71 0.01 84.14 0.08 -53.42 6.37 0.00 39.78 3.49 22.64 0.01 80.03 0.09 -57.88 6.56 0.01 17.49 3.50 17.55 0.01 73.81 0.10 -62.71 6.75 0.02 16.81 3.51 12.44 0.01 68.78 0.11 -67.57 6.94 0.02 15.13 3.51 7.30 0.01 64.80 0.12 -72.36 7.13 0.03 84.08 3.52 2.14 0.01 60.68 0.13 -77.27 7.32 0.04 82.14 3.52 -3.01 0.01 55.34 0.14 -82.39 7.51 0.04 79.53 3.52 -8.15 0.01 49.63 0.15 -51.70 7.7 0.05 76.81 3.53 -13.28 0.01 47.53 0.16 87.01 7.89 0.05 74.57 3.53 -18.47 0.01 41.87 0.17 81.73 8.08 0.06 72.42 3.52 -23.66 0.01 38.81 0.18 76.45 8.27 0.07 69.51 3.52 -28.79 0.01 35.08 0.19 71.34 8.46 0.07 66.45 3.51 -33.90 0.01 30.21 0.20 65.86 8.65 0.08 64.01 3.51 -39.00 0.01 27.00 0.21 60.25 8.84 0.08 60.83 3.51 -44.12 0.01 21.43 0.22 54.28 9.03 0.09 58.56 3.50 -49.28 0.01 17.73 0.22 48.57 9.22 0.09 55.69 3.49 -54.36 0.01 16.35 0.23 42.85 9.41 0.09 52.28 3.48 -59.39 0.01 11.43 0.23 36.83 9.6 0.10 48.64 3.47 -64.39 0.01 8.25 0.24 30.81 9.79 0.10 45.29 3.46 -69.39 0.01 4.95 0.24 24.23 9.98 0.10 41.97 3.45 -74.39 0.01 2.14 0.24 17.61 10.17 0.11 38.97 3.45 -79.32 0.01 -1.56 0.24 10.75 10.36 0.11 36.22 3.44 -84.20 0.01 -5.54 0.24 3.94 10.55 0.11 33.38 3.43 -17.05 0.01 -10.51 0.24 -3.27 10.74 0.11 30.10 3.43 86.12 0.01 -14.21 0.24 -10.81 10.93 0.11 26.91 3.43 81.37 0.01 -19.00 0.24 -18.81 5 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FMA3007 Production Datasheet v3.0 S-PARAMETERS CONTINUED S11 Frequency Mag 11.12 11.31 11.5 11.69 11.88 12.07 12.26 12.45 12.64 12.83 13.02 13.21 13.4 13.59 13.78 13.97 14.16 14.35 14.54 14.73 14.92 15.11 15.3 15.49 15.68 15.87 16.06 16.25 16.44 16.63 16.82 17.01 17.2 17.39 17.58 17.77 17.96 18.15 18.34 18.53 18.72 18.91 19.1 19.29 19.48 19.67 19.86 20 0.11 0.11 0.11 0.11 0.11 0.11 0.10 0.10 0.10 0.10 0.09 0.09 0.08 0.08 0.07 0.07 0.06 0.05 0.05 0.04 0.04 0.03 0.03 0.04 0.04 0.04 0.05 0.05 0.06 0.06 0.07 0.07 0.07 0.07 0.07 0.07 0.07 0.07 0.07 0.06 0.06 0.05 0.04 0.04 0.03 0.02 0.02 0.03 S21 S12 S22 Angle Mag Angle Mag Angle Mag Angle 22.84 3.43 76.53 0.01 -22.37 0.23 -27.22 19.06 3.43 71.78 0.01 -27.33 0.22 -36.26 14.69 3.44 67.04 0.01 -31.55 0.21 -45.16 9.79 3.45 62.28 0.01 -37.22 0.21 -55.08 6.23 3.47 57.43 0.01 -42.25 0.20 -65.94 1.32 3.49 52.51 0.01 -48.26 0.19 -77.17 -2.75 3.52 47.60 0.02 -52.88 0.18 -17.48 -7.08 3.54 42.70 0.02 -57.45 0.17 77.51 -11.05 3.58 37.72 0.02 -64.77 0.16 63.15 -15.83 3.62 32.50 0.02 -71.06 0.16 48.80 -20.74 3.65 27.22 0.02 -76.93 0.15 33.57 -26.37 3.68 21.86 0.02 -82.74 0.15 17.88 -33.12 3.72 16.46 0.02 -16.85 0.15 1.73 -39.86 3.75 11.01 0.02 85.12 0.15 -13.77 -46.40 3.78 5.41 0.02 79.01 0.15 -28.48 -54.81 3.80 -0.34 0.02 73.33 0.15 -41.98 -64.08 3.81 -6.03 0.02 68.29 0.16 -54.27 -72.76 3.82 -11.60 0.02 62.69 0.16 -65.54 -47.47 3.84 -17.22 0.02 57.29 0.16 -76.15 47.91 3.85 -22.91 0.02 51.71 0.17 -50.08 71.00 3.85 -28.64 0.02 46.06 0.17 48.74 53.20 3.84 -34.30 0.02 40.76 0.16 76.52 33.02 3.84 -39.83 0.02 34.90 0.16 69.26 13.93 3.85 -45.39 0.02 29.64 0.16 62.48 -4.28 3.85 -51.01 0.02 24.41 0.16 56.54 -18.94 3.85 -56.69 0.02 19.88 0.16 50.74 -30.60 3.85 -62.28 0.02 14.12 0.15 45.36 -41.49 3.85 -67.91 0.03 8.67 0.15 41.50 -51.22 3.86 -73.44 0.03 3.54 0.14 37.88 -59.08 3.87 -79.17 0.03 -3.05 0.14 35.17 -68.00 3.87 -84.87 0.03 -7.81 0.14 31.98 -76.62 3.87 -18.55 0.03 -13.42 0.14 28.68 -83.90 3.87 83.72 0.03 -18.83 0.13 25.14 17.35 3.87 77.99 0.03 -24.46 0.13 22.71 82.44 3.88 72.22 0.03 -29.63 0.13 20.43 76.96 3.89 66.41 0.03 -35.63 0.13 18.02 70.63 3.89 60.59 0.03 -40.03 0.13 15.16 62.97 3.89 54.74 0.03 -46.04 0.13 11.60 54.75 3.89 48.84 0.03 -51.04 0.13 7.77 45.09 3.90 42.97 0.03 -56.89 0.12 4.20 34.89 3.90 37.06 0.03 -61.73 0.12 1.11 25.38 3.90 31.13 0.03 -67.11 0.12 -3.30 14.08 3.91 25.16 0.03 -72.52 0.12 -7.78 -0.07 3.91 19.10 0.03 -78.57 0.12 -12.88 -17.44 3.92 13.14 0.03 -84.34 0.12 -19.22 -45.86 3.93 6.99 0.03 -17.99 0.11 -24.90 -13.12 3.95 0.89 0.03 84.17 0.10 -30.45 61.43 3.96 -5.39 0.03 78.45 0.10 -37.05 6 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FMA3007 Production Datasheet v3.0 BIASING CIRCUIT SCHEMATIC: VDD VG2 100pF 100pF 100nF 100nF RF Output RF Input VG1 100nF 100pF ASSEMBLY DIAGRAM: It is recommended that the RF connections be made using two bond wires 25µm in diameter and a maximum length of 300µm. Improved input return loss can be achieved, to compensate for bond wire length, with the addition of a microstrip transformer, shown in the diagram below. To Evaluation Board via an 0402 Surface Mounted capacitor 100pF Capacitor 0.8mm 0.8mm 0.61mm 0.61mm 1.0mm 1.0mm Substrate: Alumina Thickness: 635µm Transformer Impedance 43Ω Electrical Length 32º at 10GHz 100pF Capacitors To Evaluation Board via an 0402 Surface Mounted capacitor BILL OF MATERIALS: COMPONENT All RF tracks should be 50Ω characteristic material Capacitor, 100pF, chip capacitor Capacitor, 100pF, 0402 7 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FMA3007 Production Datasheet v3.0 PREFERRED ASSEMBLY INSTRUCTIONS: ORDERING INFORMATION: PART NUMBER GaAs devices are fragile and should be handled with great care. Specially designed collets should be used where possible. DESCRIPTION Die in Waffle-pack FMA3007 (Gel-pak available on request) The recommended die attach is gold/tin eutectic solder under a nitrogen atmosphere. Stage temperature should be 280-290°C; maximum time at temperature is one minute. The recommended wire bond method is thermo-compression wedge bonding with 0.7 or 1.0 mil (0.018 or 0.025 mm) gold wire. Stage temperature should be 250-260°C. Bonds should be made from the die first and then to the mounting substrate or package. The physical length of the bondwires should be minimised especially when making RF or ground connections. HANDLING PRECAUTIONS: To avoid damage to the devices care should be exercised during handling. Proper Electrostatic Discharge (ESD) precautions should be observed at all stages of storage, handling, assembly, and testing. These devices should be treated as Class 0 (0-250 V) as defined in JEDEC Standard No. 22-A114. Further information on ESD control measures can be found in MIL-STD-1686 and MILHDBK-263. APPLICATION NOTES & DESIGN DATA: Application Notes and design data including Sparameters, noise data are available on request. DISCLAIMERS: This product is not designed for use in any space based or life sustaining/supporting equipment. 8 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com