AGILENT MGA-86563-BLK

0.5 – 6 GHz Low Noise GaAs
MMIC Amplifier
Technical Data
MGA-86563
Features
• Ultra-Miniature Package
• Internally Biased, Single
+5 V Supply (14 mA)
• 1.6 dB Noise Figure at
2.4 GHz
• 21.8 dB Gain at 2.4 GHz
• +3.1 dBm P1dB at 2.4 GHz
Applications
Description
Pin Connections and
Package Marking
The MGA-86563 may be used
without impedance matching as a
high performance 2 dB NF gain
block. Alternatively, with the
addition of a simple shunt-series
inductor at the input, the device
noise figure can be reduced to
1.6 dB at 2.4 GHz. For 1.5 GHz
applications and above, the
output is well matched to 50 Ω.
Below 1.5 GHz, gain can be
increased by using conjugate
matching.
INPUT
1
GND
2
GND
3
86
• LNA or Gain Stage for ISM,
PCS, MMDS, GPS, TVRO,
and Other C band
Applications
Surface Mount Package
SOT-363 (SC-70)
6
GND
5
GND
4
OUTPUT
and Vd
Note:
Package marking provides orientation
and identification.
Agilent’s MGA-86563 is an
economical, easy-to-use GaAs
MMIC amplifier that offers low
noise figure and excellent gain for
applications from 0.5 to 6 GHz.
Packaged in an ultra-miniature
SOT-363 package, it requires half
the board space of the SOT-143.
Equivalent Circuit
RF
INPUT
4
1
RF OUTPUT
AND Vd
GROUND
2, 3, 5, 6
The circuit uses state-of-the-art
PHEMT technology with selfbiasing current sources, a sourcefollower interstage, resistive
feedback, and on-chip impedance
matching networks. A patented,
on-chip active bias circuit allows
operation from a single +5 V
power supply. Current consumption is only 14 mA, making this
part suitable for battery powered
applications.
2
MGA-86563 Absolute Maximum Ratings
Symbol
Parameter
Units
Absolute
Maximum[1]
Vd
Device Voltage, RF
Output to Ground
V
9
Vin
RF Input Voltage to
Ground
V
+0.5
–1.0
Pin
CW RF Input Power
dBm
+13
Tch
Channel Temperature
°C
150
TSTG
Storage Temperature
°C
-65 to 150
Thermal Resistance[2]:
θch-c = 160°C/W
Notes:
1. Operation of this device above any one
of these limits may cause permanent
damage.
2. TC = 25°C (TC is defined to be the
temperature at the package pins where
contact is made to the circuit board).
Electrical Specifications, TC = 25°C, ZO = 50 Ω unless noted, Vd = 5 V
Symbol
Gtest
NFtest
Parameters and Test Conditions
Gain in Test
Circuit [1]
Noise Figure in Test
Circuit [1]
Units
f = 2.0 GHz
Min.
Typ.
17
20
f = 2.0 GHz
1.8
NFO
Optimum Noise Figure
(Tuned for lowest noise figure)
f = 0.9 GHz
f = 2.0 GHz
f = 2.4 GHz
f = 4.0 GHz
f = 6.0 GHz
dB
2.0
1.5
1.6
1.7
2.0
GA
Associated Gain at NFO
(Tuned for lowest noise figure)
f = 0.9 GHz
f = 2.0 GHz
f = 2.4 GHz
f = 4.0 GHz
f = 6.0 GHz
dB
20.8
22.7
22.5
18.0
13.7
Output Power at 1 dB Gain Compression
(50 Ω Performance)
f = 0.9 GHz
f = 2.0 GHz
f = 2.4 GHz
f = 4.0 GHz
f = 6.0 GHz
dBm
3.6
4.1
4.2
4.3
3.3
Third Order Intercept Point
f = 2.4 GHz
dBm
+15
VSWR in
Input VSWR
f = 2.4 GHz
2.3:1
VSWR out
Output VSWR
f = 2.4 GHz
1.7:1
P1 dB
IP3
Id
Device Current
mA
Note:
1. Guaranteed specifications are 100% tested in the circuit in Figure 10 in the Applications Information section.
14
Max.
2.3
3
MGA-86563 Typical Performance, TC = 25°C, Vd = 5 V
3
+85
+25
2
-40
1
25
8
20
-40
+25
+85
15
10
1
2
3
4
5
0
6
1
Figure 1. Minimum Noise Figure
(Optimum Tuning) vs. Frequency and
Temperature.
4
5
0
6
1
2
3
4
5
20
5.5 V
5.0 V
4.5 V
15
10
1
2
3
4
5
6
32
OUTPUT
1.5
1
24
3.0
2.5
NF 50
2.0
1.5
16
NFopt
1.0
5
FREQUENCY (GHz)
Figure 7. Input and Output VSWR
(into 50 Ω) vs. Frequency.
6
0
2
3
5
4
6
-40
+25
+50
+85
14
GA 50
8
0.5
4
0
16
12
CURRENT (mA)
2.0
3
7.0 V
5.5 V
5.0 V
4.5 V
4
Figure 6. Output Power for 1 dB Gain
Compression (into 50 Ω) vs.
Frequency and Voltage.
ASSOCIATED GAIN (dB)
NOISE FIGURE (dB)
2.5
6
FREQUENCY (GHz)
3.5
INPUT
5
4
6
0
0
4.0
3.0
3
2
5
Figure 5. Associated Gain (Optimum
Tuning) vs. Frequency and Voltage.
3.5
2
8
FREQUENCY (GHz)
4.0
2
1
Figure 3. Output Power for 1 dB Gain
Compression (into 50 Ω) vs.
Frequency and Temperature.
25
0
6
Figure 4. Minimum Noise Figure
(Optimum Tuning) vs. Frequency and
Voltage.
1
0
10
FREQUENCY (GHz)
0
-40
+25
+50
FREQUENCY (GHz)
P 1 dB (dBm)
5.5 V
5.0 V
4.5 V
2
ASSOCIATED GAIN (dB)
NOISE FIGURE (dB)
3
1
VSWR (n:1)
3
30
4
1.0
2
Figure 2. Associated Gain (Optimum
Tuning) vs. Frequency and
Temperature.
5
0
4
FREQUENCY (GHz)
FREQUENCY (GHz)
0
6
2 +85
5
0
0
P 1 dB (dBm)
ASSOCIATED GAIN (dB)
NOISE FIGURE (dB)
4
0
10
30
5
10
8
6
4
2
0
2
4
6
8
10
FREQUENCY (GHz)
Figure 8. 50 Ω Noise Figure and
Associated Gain vs. Frequency.
0
12
0
0
1
2
3
4
5
6
7
VOLTAGE (V)
Figure 9. Device Current vs. Voltage.
4
MGA-86563 Typical Scattering Parameters [1], TC = 25°C, Z O = 50 Ω, Vd = 5 V
Freq.
GHz
Mag.
S11
Ang.
dB
S21
Mag.
Ang.
dB
S12
Mag.
Ang.
Mag.
Ang.
K
Factor
0.1
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
0.84
0.57
0.55
0.53
0.47
0.38
0.26
0.14
0.04
0.04
0.07
0.09
0.11
0.12
0.13
0.15
0.17
-17
-29
-41
-57
-73
-89
-104
-115
-106
-6
2
-4
-17
-28
-36
-44
-53
3.1
14.7
18.9
20.8
21.7
21.8
21.3
20.2
18.8
17.4
16.1
14.9
13.9
12.9
12.0
11.1
10.4
1.42
5.41
8.77
10.97
12.14
12.33
11.61
10.23
8.75
7.44
6.41
5.57
4.93
4.40
3.96
3.58
3.30
76
41
4
-29
-62
-94
-125
-152
-177
162
143
126
110
94
79
65
51
-39.8
-44.3
-51.2
-52.1
-45.2
-40.7
-37.4
-34.4
-32.6
-30.9
-29.6
-28.1
-26.0
-24.9
-23.8
-22.6
-22.6
0.010
0.006
0.003
0.002
0.005
0.009
0.014
0.018
0.023
0.027
0.032
0.038
0.044
0.050
0.057
0.065
0.074
15
-23
-2
70
96
102
100
97
92
88
83
78
72
65
59
53
44
0.85
0.59
0.46
0.38
0.32
0.24
0.16
0.09
0.03
0.03
0.05
0.06
0.08
0.08
0.09
0.11
0.13
-15
-39
-53
-66
-78
-89
-99
-102
-82
1
20
19
14
4
-3
-12
-21
3.27
6.77
10.49
14.23
5.94
3.78
2.92
2.75
2.58
2.58
2.53
2.45
2.38
2.35
2.29
2.21
2.10
MGA-86563 Typical Noise Parameters [1],
TC = 25°C, ZO = 50 Ω, Vd = 5 V
Γopt
Frequency
(GHz)
NFo
(dB)
Mag.
Ang.
RN/50 Ω
5
1.0
1.5
2.0
2.5
3.0
4.0
5.0
6.0
2.8
1.8
1.5
1.5
1.6
1.6
1.7
1.9
2.1
0.61
0.56
0.50
0.45
0.41
0.38
0.32
0.24
0.15
4
24
33
40
50
57
73
98
131
1.16
0.47
0.34
0.38
0.33
0.30
0.28
0.27
0.24
Note:
1. Reference plane per Figure 11 in Applications Information section.
S22
5
MGA-86563 Applications
Information
The parameter test circuit uses a
high impedance RF choke to
apply Vd to the MMIC while
isolating the power supply from
the RF Output of the amplifier.
Introduction
The MGA-86563 is a high gain,
low noise RF amplifier for use in
wireless RF applications within
the 0.5 to 6 GHz frequency range.
The MGA-86563 is a three-stage,
GaAs Microwave Monolithic
Integrated Circuit (MMIC) amplifier that uses internal feedback to
provide wideband gain and
impedance matching.
Phase Reference Planes
The positions of the reference
planes used to measure SParameters and to specify Γopt for
the Noise Parameters are shown
in Figure 11. As seen in the
illustration, the reference planes
are located at the extremities of
the package leads.
A patented, active bias circuit
makes use of current sources to
“re-use” the drain current in all
three stages of gain, thus minimizing the required supply current
and decreasing sensitivity to
variations in power supply
voltage.
Biasing
The MGA-86563 is a voltagebiased device and operates from
a single +5 volt power supply.
With a typical current drain of
only 14 mA, the MGA-86563 is
suitable for use in battery
powered applications. RF
performance is very stable over a
wide variation of power supply
voltage.
Test Circuit
The circuit shown in Figure 10 is
used for 100% RF testing of Noise
Figure and Gain. The input of this
circuit is fixed tuned for a conjugate power match (maximum
power transfer, or, minimum
Input VSWR) at 2 GHz. Tests in
this circuit are used to guarantee
the NFtest and Gtest parameters
shown in the Electrical Specifications Table.
Since DC bias is applied to the
MGA-86563 through the RF
Output pin, some method of
isolating the RF from the DC
must be provided. An RF choke
or length of high impedance
transmission line is typically used
for this purpose.
SOT-363 PCB Layout
A PCB pad layout for the miniature SOT-363 (SC-70) package
used by the MGA-86563 is shown
in Figure 12 (dimensions are in
inches). This layout provides
ample allowance for package
placement by automated
assembly equipment without
adding parasitics that could
impair the high frequency RF
performance of the MGA-86563.
The layout is shown with a
nominal SOT-363 package
footprint superimposed on the
PCB pads.
0.026
REFERENCE
PLANES
0.075
TEST CIRCUIT
0.035
0.016
Figure 11. Reference Planes.
The 3.3 nH inductor, L1
(Coilcraft, Cary, IL or equivalent)
in series with the input of the
amplifier matches the input to
50 Ω at 2 GHz.
Figure 12. PCB Pad Layout
(dimensions in inches).
w = 15
I = 1000
BOARD MATERIAL = 1/16" FR-4
RFC
(28 nH)
L1
3.3 nH
RF
INPUT
w = 110
(50 Ω)
Vd
C1
w = 110
I = 110
w = 110
(50 Ω)
Figure 10. Test Circuit for 2 GHz.
RF
OUTPUT
6
RF Layout
The RF layout in Figure 13 is
suggested as a starting point for
amplifier designs using the MGA86563 MMIC. Adequate grounding
is needed to obtain maximum
performance and to obviate
potential instability. All four
ground pins of the MMIC should
be connected to RF ground by
using plated through holes (vias)
near the package terminals.
It is recommended that the PCB
pads for the ground pins NOT be
connected together underneath
the body of the package. PCB
traces hidden under the package
cannot be adequately inspected
for SMT solder quality.
PCB Material
FR-4 or G-10 printed circuit board
material is a good choice for most
low cost wireless applications.
Typical board thickness is 0.020
or 0.031 inches. The width of 50 Ω
microstriplines in PC boards of
these thicknesses is also
convenient for mounting chip
components such as the series
inductor that is used at the input
for impedance matching or for
DC blocking capacitors.
For applications requiring the
lowest noise figures, the use of
50 Ω
RF INPUT
86
50 Ω
decoupling network shown in
Figure 14, consisting of resistor
R1, a short length of high
impedance microstripline, and
bypass capacitor C3, will provide
excellent performance over a
wide frequency range. Surface
mount chip inductors could be
used in place of the high
impedance transmission line to
act as an RF choke. Consideration
should be given to potential
resonances and signal radiation
when using lumped inductors.
PTFE/glass dielectric materials
may be warranted to minimize
transmission line losses at the
amplifier input. A 0.5 inch length
of 50 Ω microstripline on FR-4
has approximately 0.3 dB loss at
4 GHz which will add directly to
the noise figure of the
MGA-86563.
Typical Application Circuit
A typical implementation of the
MGA-86563 as a low noise amplifier is shown in Figure 14.
A 50 Ω microstripline with a
series DC blocking capacitor, C1,
is used to feed RF to the MMIC.
The input of the MGA-86563 is
already partially matched for
noise figure and gain to 50 Ω. The
use of a simple input matching
circuit, such as a series inductor,
will minimize amplifier noise
figure. Since the impedance
match for NFO (minimum noise
figure) is very close to a
conjugate power match, a low
noise figure can be realized
simultaneously with a low input
VSWR.
For operation at frequencies
below approximately 2 GHz, the
addition of a simple impedance
matching circuit to the output
will increase the gain and output
power by 0.5 to 1.5 dB. The
output matching circuit will not
effect the noise figure.
A small value resistor placed in
series with the Vdd line may be
useful to “de-Q” the bias circuit.
Typical values of R1 are in the
10 Ω to 100 Ω range. Depending
on the value of resistance used,
the supply voltage may have to be
increased to compensate for voltage drop across R1. The power
supply should be capacitively
bypassed (C3) to ground to
prevent undesirable gain variations and to eliminate unwanted
feedback through the bias lines
that could cause oscillation.
DC power is applied to the MMIC
through the same pin that is
shared with the RF output. A 50 Ω
microstripline is used to connect
the device to the following stage.
A bias decoupling network is used
to feed in Vd while simultaneously providing a DC block to
the RF signal. The bias
RF OUTPUT
AND Vd
Vd
C3
HIGH Z
Figure 13. RF Layout.
R1
C1
50 Ω
C2
L1
50 Ω
50 Ω
Figure 14. Typical Amplifier Circuit.
50 Ω
7
Higher Bias Voltages
While the MGA-86563 is designed
primarily for use in +5 volt
applications, the internal bias
regulation circuitry allows it to be
operated with any power supply
voltage from +5 to +7 volts. The
use of +7 volts increases the P1dB
by approximately 1 dBm. The
effect on noise figure, gain, and
VSWR with higher Vd is negligible.
MGA-86563 Part Number Ordering Information
Part Number
Devices per Container
Container
MGA-86563-TR1
3000
7" reel
MGA-86563-BLK
100
Antistatic bag
For more information call your
nearest HP sales office.
Package Dimensions
Outline 63 (SOT-363/SC-70)
1.30 (0.051)
REF.
2.20 (0.087)
2.00 (0.079)
1.35 (0.053)
1.15 (0.045)
0.650 BSC (0.025)
0.425 (0.017)
TYP.
2.20 (0.087)
1.80 (0.071)
0.10 (0.004)
0.00 (0.00)
0.30 REF.
1.00 (0.039)
0.80 (0.031)
0.25 (0.010)
0.15 (0.006)
10°
0.30 (0.012)
0.10 (0.004)
DIMENSIONS ARE IN MILLIMETERS (INCHES)
0.20 (0.008)
0.10 (0.004)
Device Orientation
REEL
END VIEW
TOP VIEW
4 mm
CARRIER
TAPE
8 mm
86
86
86
86
USER
FEED
DIRECTION
COVER TAPE
Tape Dimensions and Product Orientation
For Outline 63
P
P2
D
P0
E
F
W
C
D1
t1 (CARRIER TAPE THICKNESS)
Tt (COVER TAPE THICKNESS)
K0
8° MAX.
A0
DESCRIPTION
5° MAX.
B0
SYMBOL
SIZE (mm)
SIZE (INCHES)
CAVITY
LENGTH
WIDTH
DEPTH
PITCH
BOTTOM HOLE DIAMETER
A0
B0
K0
P
D1
2.24 ± 0.10
2.34 ± 0.10
1.22 ± 0.10
4.00 ± 0.10
1.00 + 0.25
0.088 ± 0.004
0.092 ± 0.004
0.048 ± 0.004
0.157 ± 0.004
0.039 + 0.010
PERFORATION
DIAMETER
PITCH
POSITION
D
P0
E
1.55 ± 0.05
4.00 ± 0.10
1.75 ± 0.10
0.061 ± 0.002
0.157 ± 0.004
0.069 ± 0.004
CARRIER TAPE
WIDTH
THICKNESS
W
t1
8.00 ± 0.30
0.255 ± 0.013
0.315 ± 0.012
0.010 ± 0.0005
COVER TAPE
WIDTH
TAPE THICKNESS
C
Tt
5.4 ± 0.10
0.062 ± 0.001
0.205 ± 0.004
0.0025 ± 0.00004
DISTANCE
CAVITY TO PERFORATION
(WIDTH DIRECTION)
F
3.50 ± 0.05
0.138 ± 0.002
CAVITY TO PERFORATION
(LENGTH DIRECTION)
P2
2.00 ± 0.05
0.079 ± 0.002
www.semiconductor.agilent.com
Data subject to change.
Copyright © 1999 Agilent Technologies
Obsoletes 5965-4746E
5965-9686E (11/99)