13 mm Dia. SIDE-ON COMPACT TYPE PHOTOMULTIPLIER TUBE SERIES 13 mm (1/2 Inch) Diameter, 9-stage, Side-on Type The R6350 to R6358 series are compact side-on photomultiplier tubes with a 13 mm diameter and 50 mm height. Using different photocathode and window material combinations helped to produce a full product lineup to cover a wide spectral response range from the UV to the near infrared. This allows selecting the optimal tube to match your application and wavelength to be detected, the same as when selecting the popular 28 mm (1-1/8 inch) side-on tubes. The R6356-06 and R6357 do not use an entrance mesh (grill) which is usually installed just inside the light input window. This eliminates the light loss caused by the entrance mesh, even if the size of incident light beam is small. Left: Fused silica window Center: UV window Right: Meshless type (R6356-06, R6357) APPLICATIONS ●Emission Spectroscopy (ICP, Direct Reader) ●Environmental Monitoring (NOx, SO2, etc.) ●Fluorescence Immunoassay ●Chemiluminescence Immunoassay ●Hygiene Monitor (Bio Luminescence) ●X-ray Phototimer ●Fluorometer ●Microscope (Laser Scanning Microscope) Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office. Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2005 Hamamatsu Photonics K.K. 13 mm Dia. SIDE-ON COMPACT TYPE PHOTOMULTIPLIER TUBE SERIES Side-On Compact Type Photomultiplier Tubes A Spectral Response Type No. Remarks Range (nm) B C Peak PhotoWave- cathode Window Outline length Material Material No. D Dynode Structure No. of Stages (nm) Socket Maximum F Cathode Sensitivity Ratings Luminous G Anode to Average Cathode Anode Min. Typ. Socket Assembly Voltage Current (V) (mA) (µA/lm) (µA/lm) R6350 For UV to visible range, 185 to 650 general purpose. 340 Sb-Cs U 1 CC/9 E678-11U/E 1250 0.01 20 40 R6351 Synthetic silica window type of R6350 160 to 650 340 Sb-Cs Q 2 CC/9 E678-11U/E 1250 0.01 20 40 R6352 High sensitivity variant of R6350 185 to 750 420 BA U 1 CC/9 E678-11U/E 1250 0.01 80 120 R6353 Low dark current bialkali photocathode 185 to 680 400 LBA U 1 CC/9 E678-11U/E 1250 0.01 30 70 R6354 For UV range 160 to 320 230 Cs-Te Q 2 CC/9 E678-11U/E 1250 0.01 — — R6355 For UV to near IR range, 185 to 850 general purpose 530 MA U 1 CC/9 E678-11U/E 1250 0.01 80 150 185 to 900 400 MA U 1 CC/9 E678-11U/E 1250 0.01 200 300 185 to 900 450 MA U 1 CC/9 E678-11U/E 1250 0.01 350 500 Low dark current 185 to 830 multialkali photocathode 530 LMA U 1 CC/9 E678-11U/E 1250 0.01 140 200 High sensitivity R6356-06 * variant of R6355 R6357 * R6358 Meshless type High sensitivity variant of R6356-06, Meshless type * Achieved the higher photocathode sensitivity by eliminating the mesh in front of the photocathode. It also features no output variation, disturbed by the mesh, when the incident light spot to the photocathode is small. NOTE: A Photocathode materials B Window materials BA: Bialkali Q: Fused silica LBA: Low dark current bialkali U: UV glass MA: Multialkali LMA: Low dark current multialkali D Dynode structure E See optional accessories CC: Circular-cage G Averaged over any interval of 30 seconds maximum. C Outline No. See Fig. 9 F The maximum operating ambient temperature range is -30 °C to +50 °C. K Anode Characteristics L Cathode Sensitivity H J Anode to Anode Dark Anode Sensitivity Blue Current J Sens. Red/ Radiant Cathode Luminous Supply Gain (After 30 min.) Radiant Index White Typ. (CS 5-58) Ratio Typ. Voltage Min. Typ. Typ. Typ. Max. Typ. Typ. (V) (A/lm) (A/lm) (A/W) (nA) (nA) (mA/W) Time Response Rise Electron Time Transit Time Typ. Typ. (ns) (ns) Notes Type No. 5 — 48 1000 50 300 3.6 × 105 7.5 × 106 0.5 5 1.4 15 Photon counting type: R6350 R6350P Dark Count 30 s-1 Max. 5 — 48 1000 50 300 3.6 × 105 7.5 × 106 0.5 5 1.4 15 R6351 10 — 90 1000 100 700 5.2 × 105 5.8 × 106 1 10 1.4 15 R6352 6.5 — 65 1000 100 400 3.7 × 105 5.7 × 106 0.1 2 1.4 15 Photon counting type: R6353 R6353P Dark Count 30 s-1 Max. — — 62 1000 — — 1.8 × 105 3 × 106 0.5 5 1.4 15 R6354 6 0.15 45 1000 100 600 1.8 × 105 4 × 106 1 10 1.4 15 R6355 10 0.3 77 1000 400 2000 5.2 × 105 6.7 × 106 1 10 1.4 15 R6356-06 * 13 0.4 105 1000 1000 2000 4.2 × 105 4 × 106 2 10 1.4 15 R6357 * 7.5 0.15 70 1000 300 3.5 × 106 0.1 1 1.4 15 M M 700 2.5 × 105 H Measured using red filter Toshiba R-68. J Measured at the peak wavelength. L Anode characteristics are measured with the supply voltage and voltage distribution ratio specified by Note N. N Voltage distribution ratio and voltage. M: at 254 nm Electrodes K Dy1 Dy2 Dy3 Dy4 Dy5 Dy6 Dy7 Dy8 Dy9 P Distribution Ratio 1 1 1 1 1 1 1 1 1 1 Supply Voltage: 1000 V, K: Cathode, Dy: Dynode, P: Anode Photon counting type: R6358-10 R6358 Dark Count 300 s-1 Max. K Refer to Note N. 13 mm Dia. SIDE-ON COMPACT TYPE PHOTOMULTIPLIER TUBE SERIES Figure 1: Typical Spectral Response of Cs-Te Figure 2: Typical Spectral Response of BA, LBA, Sb-Cs TPMSB0128EA TPMSB0114EA 100 100 R6352 CATHODE RADIANT SENSITIVITY (mA/W) QUANTUM EFFICIENCY (%) CATHODE RADIANT SENSITIVITY (mA/W) QUANTUM EFFICIENCY (%) R6354 10 1 0.1 10 R6350 R6353 1 R6351 0.1 RADIANT SENSITIVITY QUANTUM EFFICIENCY RADIANT SENSITIVITY QUANTUM EFFICIENCY 0.01 100 200 300 400 0.01 100 500 200 400 500 600 700 800 WAVELENGTH (nm) WAVELENGTH (nm) Figure 3: Typical Spectral Response of MA, LMA Figure 4: Typical Spectral Response of High Sensitivity MA TPMSB0115EA TPMSB0116EB 100 1000 R6358 10 R6355 1 0.1 WAVELENGTH (nm) R6357 100 10 R6356-06 1 0.1 RADIANT SENSITIVITY QUANTUM EFFICIENCY RADIANT SENSITIVITY QUANTUM EFFICIENCY 0.01 100 200 300 400 500 600 700 CATHODE RADIANT SENSITIVITY (mA/W) QUANTUM EFFICIENCY (%) CATHODE RADIANT SENSITIVITY (mA/W) QUANTUM EFFICIENCY (%) 300 800 900 1000 0.01 100 200 300 400 500 600 700 WAVELENGTH (nm) 800 900 1000 Figure 5: Typical Gain 108 Figure 6: Typical Time Response TPMSB0208EA TPMSB0118EA 100 107 R6350 R6355 R6357 TIME (ns) GAIN 106 105 TRANSIT TIME 10 104 RISE TIME 103 102 300 400 500 600 800 1000 1 500 1500 1000 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) Figure 7: Typical ENI Characteristics Figure 8: Typical Anode Uniformity TPMSB0119EA INSULATOR BASE PIN TOP VIEW 10-13 BULB PHOTOCATHODE R6353 10-14 MESH R6357: MESHLESS TYPE R6350 10-15 R6357 10-16 10-17 100 200 300 400 500 600 700 800 900 1000 WAVELENGTH (nm) ANODE RELATIVE OUTPUT (%) EQUIVALENT NOISE INPUT (W) 10-12 1500 100 50 FWHM: 3.7 mm 0 2 LEFT 1 0 1 2 (mm) RIGHT TPMSC0036EA 13 mm Dia. SIDE-ON COMPACT TYPE PHOTOMULTIPLIER TUBE SERIES Figure 9: Dimensional Outline and Basing Diagram (Unit: mm) Outline No.1 Outline No.2 13.5 ± 0.8 13.5 ± 0.8 PHOTOCATHODE 4 MIN. PHOTOCATHODE 4 MIN. DY5 6 DY6 7 8 7±2 DY7 9 DY8 42 ± 2 DY3 4 52 MAX. 24.0 ± 1.5 50 MAX. 13 MIN. 3±2 40 ± 2 24.0 ± 1.5 13 MIN. DY4 5 DY2 10 DY9 3 11 P 2 1 DY1 K DIRECTION OF LIGHT BOTTOM VIEW UV WINDOW FUSED SILICA WINDOW TPMSA0034EB Socket E678-11U E678-11T (Sold Separately): For direct soldering to PC board 24 12.4 5.5 5.5 45 30 ° ° 18 ° 30 DIRECTION OF LIGHT 13 10.5 3 10.5 4 0.5 3 2.7 12.4 0.5 11 11 TACCA0181EB TACCA0161EB OPTIONAL ACCESSORIES D-Type Socket Assembly Type No. E850-13E Grounded Electrode / Supply Voltage Polarity Supply Voltage between Case and Pins (V) Anode / – 1500 Maximum Ratings D Supply Voltage Voltage between Divider Power Supply Current Terminals (V) (mA) 1250 B A 0.38 Leakage Current in Signal C Total Voltage Divider Resistance Max. (A) (MΩ) Maximum Linear Output in DC Mode (µA) 1 × 10-10 3.3 18 (at 1250 V) Signal Output DC/Pulse E850-22: with SHV, BNC connector NOTE: A Measured with the maximum supply voltage. B Measured with a supply voltage of 1000 V. C The current at which the output linearity is kept within ±5 %. D Operating temperature range is -20 °C to +50 °C. E Supplied with a separate mounting flange. See below for assembled dimensions. Dimensional Outline and Circuit Diagram (Unit: mm) E850-13 Mounting Flange for E850-13 DY9 10 12.6 ± 0.5 DY8 9 12.4 ± 0.5 DY7 8 DY6 7 DY5 6 HOUSING (INSULATOR) POTTING COMPOUND R10 C3 R9 C2 R8 C1 2.5 20° 1 2- 3.2 R1 5.0 ± 0.5 10 5 P R7 R6 R5 DY4 5 DY3 4 DY2 3 DY1 K 2 R1 to R10 : 330 kΩ C1 to C3 : 10 nF 7.0 ± 0.3 450 ± 10 14.0 ± 0.3 36.0 ± 0.3 SIGNAL GND SIGNAL OUTPUT RG-174/U (BLACK) POWER SUPPLY GND AWG22 (BLACK) 5 R1 35.0 ± 0.5 0.5 MAX. 11 15.0 ± 0.3 PMT SOCKET PIN No. R4 R3 R2 R1 1 -HV AWG22 (VIOLET) TACCA0096EC TACCA0097EB 13 mm Dia. SIDE-ON COMPACT TYPE PHOTOMULTIPLIER TUBE SERIES LENS FOR 1/2 INCH DIAMETER SIDE-ON TYPE PHOTOMULTIPLIER TUBES The optimized cylindrical lens which can be attached at the entrance window of 1/2 inch side-on photomultiplier tube. This lens helps the incident light reaches the photocathode efficiently. With this lens, the effective area widens by the factor of two in case of 1/2" PMT (7.5 mm width). The lens transmits above 300 nm light only. Figure 10: Transmittance of Lens 100 TPMSB0191EA TRANSMITTANCE (%) 90 LENS LUMINOUS FLUX LENS 80 70 60 50 40 30 20 10 0 200 300 400 500 600 700 800 900 TPMSC0042EA WAVELENGTH (nm) Lens Material: Acrylic resin Figure 11: Uniformity Figure 12: Lens Effect (Ex.: R6358) 250 100 ANODE SENSITIVITY WITH LENS WITHOUT LENS 0 X-AXIS (mm) 3.75 6.5 0 3.75 0 50 200 100 PARALLEL LIGHT WITH LENS DIFFUSED LIGHT WITH LENS 150 100 WITHOUT LENS 50 0 Y-AXIS (mm) RELATIVE OUTPUT (%) 50 TPMSB0192EA 0 300 LENS 400 500 600 700 800 900 WAVELENGTH (nm) 6.5 Parallel light: Uniform and sufficiently large area, than the sensitive area size, of the parallel incident light (40 mm dia.) shall be given to the photomultiplier tube. MEASUREMENT CONDITIONS WAVELENGTH: 400 nm SUPPLY VOLTAGE: -1000 V A 1 mm diameter spot light (parallel light) is scanned at the center of the photocathode in X and Y directions. TPMSC0041EA Diffused light: Parallel light (40 mm dia.) is given to the photomultiplier tube through the diffuser, which locates 10 cm from the tube. NOTE: The lens only (without photomultiplier tube) is not available. WARNING ~High Voltage~ The product is operated at high voltage potential. Further, the metal housing of the product is connected to the photocathode (potential) so that it becomes a high voltage potential when the product is operated at a negative high voltage (anode grounded). Accordingly, extreme safety care must be taken for the electrical shock hazard to the operator or the damage to the other instruments. WEB SITE http://www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Electron Tube Division 314-5, Shimokanzo, Iwata City, Shizuoka Pref., 438-0193, Japan, Telephone: (81)539/62-5248, Fax: (81)539/62-2205 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P. O. Box 6910, Bridgewater. N.J. 08807-0910, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 E-mail: [email protected] Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658 E-mail: [email protected] France: Hamamatsu Photonics France S.A.R.L.: 8, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 E-mail: [email protected] United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road Welwyn Garden City Hertfordshire AL7 1BW, United Kingdom, Telephone: 44-(0)1707-294888, Fax: 44(0)1707-325777 E-mail: [email protected] North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171-41 SOLNA, Sweden, Telephone: (46)8-509-031-00, Fax: (46)8-509-031-01 E-mail: [email protected] TPMS1032E05 Italy: Hamamatsu Photonics Italia: S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39)02-935 81 733, Fax: (39)02-935 81 741 E-mail: [email protected] JUN. 2005. IP