HOLTEK HT36FA

HT36FA
Music Synthesizer 8-Bit MCU
Technical Document
· Tools Information
· FAQs
· Application Note
Features
· Operating voltage: 2.4V~5.0V
· Stereo 16-bit DAC
· Operating frequency:
· Oscillation modes: XTAL/RCOSC
· Low voltage reset
X¢tal: 6MHz~8MHz
ROSC: typ. 6MHz
· Eight-level subroutine nesting
· Built-in 128K´16-bit (2M-bit) ROM for program/data
· Supports 8-bit table read instruction (TBLP)
shared
· HALT function and wake-up feature reduce power
· Built-in 8 bit MCU with 208´8 bits RAM
consumption
· Two 8 bit programmable timer with 8 stage prescaler
· Bit manipulation instructions
· 24 bidirectional I/O lines
· 63 powerful instructions
· Watchdog timer
· All instructions in 1 or 2 machine cycles
· Four polyphonic synthesizer
· 20/32-pin SOP package
General Description
microprocessor which controls the synthesizer to generate the melody by setting the special register. A HALT
feature is provided to reduce power consumption.
The HT36FA is an 8-bit high performance RISC architecture microcontroller specifically designed for various
music applications. It provides an 8-bit MCU and a
4-channel Wavetable synthesizer. It has a built-in 8-bit
Block Diagram
P A 0 ~ P A 7
P B 0 ~ P B 7
P C 0 ~ P C 7
O S C 1
O S C 2
R E S
Rev. 1.10
1 2 8 K ´ 1 6 - b it
R O M
8 - B it
M C U
V D
V S
V D
V S
2 0 8 ´ 8
R A M
M u ltip lie r /P h a s e
G e n e ra l
1
1 6 - B it
D A C
D
S
D A
S A
L C H
R C H
March 13, 2006
HT36FA
Pin Assignment
P B 3
1
3 2
P B 4
P B 2
2
3 1
P B 5
P B 1
3
3 0
P B 6
P B 0
4
2 9
P B 7
R C H
5
2 8
P A 7
L C H
6
2 7
P A 6
P B 0
1
2 0
P B 7
V D D A
7
2 6
P A 5
R C H
2
1 9
P A 7
V S S A
8
P A 4
V D D A
3
1 8
P A 6
O S C 2
2 5
9
2 4
P A 3
V S S A
4
1 7
P A 5
O S C 1
1 0
P A 2
O S C 2
5
1 6
P A 4
V S S
1 1
2 3
O S C 1
6
1 5
P A 3
V D D
1 2
2 1
P A 0
V S S
7
1 4
P A 2
R E S
1 3
2 0
P C 0
V D D
8
1 3
P A 1
P C 6
1 4
1 9
P C 1
R E S
9
1 2
P A 0
P C 5
1 5
1 8
P C 2
P C 7
1 0
1 1
P C 0
P C 4
1 6
1 7
P C 3
2 2
P A 1
H T 3 6 F A
3 2 S O P -A
H T 3 6 F A
2 0 S O P -A
Pad Assignment
P B 6
P B 7
P A 7
P A 6
P A 5
4
P B 5
V S S A
P B 4
3
P B 3
V D D A
P B 2
2
P B 1
1
L C H
P B 0
R C H
3 3
3 2
3 1
3 0
2 9
2 8
2 7
2 6
2 5
2 4
2 3
(0 ,0 )
O S C 2
5
O S C 1
6
1 2
1 3
1 4
1 5
1 6
1 7
1 8
1 9
P C 3
P C 2
P C 1
P C 0
P A 0
P A 1
1 1
P C 4
1 0
P C 5
V D D
9
P C 6
8
R E S
7
P C 7
V S S
2 2
P A 4
2 1
P A 3
2 0
P A 2
Chip size: 2385 ´ 3225 (mm)2
* The IC substrate should be connected to VSS in the PCB layout artwork.
Rev. 1.10
2
March 13, 2006
HT36FA
Pad Coordinates
Unit: mm
Pad No.
X
Y
Pad No.
X
Y
1
-1003.950
1463.950
18
708.150
-1448.750
2
-1003.950
1350.950
19
818.750
-1448.750
3
-1003.950
1238.510
20
1042.350
-1448.200
4
-1003.950
1089.850
21
1042.350
-1348.200
5
-1042.350
-587.774
22
1042.350
6
-1042.350
-1265.626
23
1041.900
-1237.600
1462.150
7
-1052.100
-1439.900
24
941.900
1462.150
8
-952.100
-1439.900
25
831.300
1462.150
9
-236.026
-1448.750
26
731.300
1462.150
10
-134.250
-1448.750
27
620.700
1462.150
11
-23.650
76.350
-1448.750
28
520.700
1462.150
12
-1448.750
29
410.100
1462.150
13
186.950
-1448.750
30
310.100
1462.150
14
286.950
-1448.750
31
199.500
1462.150
15
397.550
-1448.750
32
99.500
1462.150
16
497.550
-1448.750
33
-11.100
1462.150
17
608.150
-1448.750
Pad Description
Pad No.
Pad Name
I/O
Internal
Connection
Function
8, 7
VDD, VSS
¾
¾
Digital power supply, ground
3,4
VDDA, VSSA
¾
¾
DAC power supply
18~25
PA0~PA7
I/O
Wake-up,
Pull-high or
None
Bidirectional 8-bit I/O port, wake-up by mask option
33~26
PB0~PB7
I/O
Pull-high or
None
Bidirectional 8-bit I/O port
17~10
PC0~PC7
I/O
Pull-high or
None
Bidirectional 8-bit I/O port
9
RESET
I
¾
6
OSC1
I
X¢tal/Resistor
5
OSC2
O
¾
XOUT or T1
1
RCH
O
¾
DAC output R channel
2
LCH
O
¾
DAC output L channel
Reset input, active low
XIN for X¢tal or ROSCIN for resistor by mask option
Absolute Maximum Ratings
Supply Voltage ..........................VSS-0.3V to VSS+5.5V
Storage Temperature ...........................-50°C to 125°C
Input Voltage .............................VSS-0.3V to VDD+0.3V
Operating Temperature ..........................-25°C to 70°C
Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may
cause substantial damage to the device. Functional operation of this device at other conditions beyond those
listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
Rev. 1.10
3
March 13, 2006
HT36FA
Electrical Characteristics
Symbol
Parameter
VDD
Operating Voltage
IDD
Operating Current
Ta=25°C
Test Conditions
Min.
Typ.
Max.
Unit
2.4
4.5
5
V
¾
2
8
¾
8
10
¾
1
¾
¾
1
5
¾
5
¾
¾
mA
¾
5
¾
¾
mA
VDD
Conditions
¾
¾
3V
No load (OSC= 6MHz)
4.5V
ISTB
3V
Standby Current
WDT enable (RC OSC)
4.5V
3V
mA
mA
IOH
Flag Source Current
IOL
Flag Sink Current
VIH
Input High Voltage for I/O Ports
¾
¾
0.8VDD
¾
VDD
V
VIL
Input Low Voltage for I/O Ports
¾
¾
0
¾
0.2VDD
V
Rev. 1.10
4.5V
3V
4.5V
4
March 13, 2006
HT36FA
Function Description
Execution Flow
When executing a jump instruction, conditional skip execution, loading PCL register, subroutine call, initial reset, internal interrupt, external interrupt or return from
subroutine, the PC manipulates the program transfer by
loading the address corresponding to each instruction.
The system clock for the HT36FA is derived from either
a crystal or an RC oscillator. The oscillator frequency divided by 2 is the system clock for the MCU and it is internally divided into four non-overlapping clocks. One
instruction cycle consists of four system clock cycles.
The conditional skip is activated by instruction. Once the
condition is met, the next instruction, fetched during the
current instruction execution, is discarded and a dummy
cycle replaces it to retrieve the proper instruction. Otherwise proceed with the next instruction.
Instruction fetching and execution are pipelined in such
a way that a fetch takes one instruction cycle while decoding and execution takes the next instruction cycle.
However, the pipelining scheme causes each instruction to effectively execute in one cycle. If an instruction
changes the program counter, two cycles are required
to complete the instruction.
The lower byte of the program counter (PCL) is a readable and writeable register (06H). Moving data into the
PCL performs a short jump. The destination will be
within 256 locations.
Program Counter - PC
Once a control transfer takes place, an additional
dummy cycle is required.
The 13-bit program counter (PC) controls the sequence
in which the instructions stored in program ROM are executed and its contents specify a maximum of 8192 addresses for each bank.
Program ROM
HT36FA provides 18 address lines WA17~WA0 to read
the Program ROM which is up to 2M bits, and is commonly used for the wavetable voice codes and the program memory. It provides two address types, one type is
for program ROM, which is addressed by a bank pointer
PF3~PF0 and a 13-bit program counter PC12~PC0;
After accessing a program memory word to fetch an instruction code, the contents of the program counter are
incremented by one. The program counter then points
to the memory word containing the next instruction
code.
S y s te m C lo c k o f M C U
( S y s te m C lo c k /2 )
T 1
T 2
T 3
T 4
T 1
T 2
T 3
P C
P C
T 4
T 1
T 2
P C + 1
F e tc h IN S T (P C )
E x e c u te IN S T (P C -1 )
T 3
T 4
P C + 2
F e tc h IN S T (P C + 1 )
E x e c u te IN S T (P C )
F e tc h IN S T (P C + 2 )
E x e c u te IN S T (P C + 1 )
Execution Flow
Mode
Initial Reset
Program Counter
*16 *15 *14 *13 *12 *11 *10 *9
0
0
0
0
*8
*7
*6
*5
*4
*3
*2
*1
*0
0
0
0
0
0
0
0
0
0
0
0
0
0
Timer/Event Counter 0 Overflow PF3 PF2 PF1 PF0 0
0
0
0
0
0
0
0
0
1
0
0
0
Timer/Event Counter 1 Overflow PF3 PF2 PF1 PF0 0
0
0
0
0
0
0
0
0
1
1
0
0
Skip
Program Counter+2
Loading PCL
PF3 PF2 PF1 PF0 *12 *11 *10 *9
*8 @7 @6 @5 @4 @3 @2 @1 @0
Jump, Call Branch
PF3 PF2 PF1 PF0 #12 #11 #10 #9
#8
Return From Subroutine
PF3 PF2 PF1 PF0 S12 S11 S10 S9 S8 S7 S6 S5 S4 S3 S2 S1 S0
#7
#6
#5
#4
#3
#2
#1
#0
Program Counter
Note:
*12~*0: Bits of Program Counter
S12~S0: Bits of Stack Register
@7~@0: Bits of PCL
@7~@0: Bits of PCL
#12~#0: Bits of Instruction Code
PF3~PF0: Bits of Bank Register
Rev. 1.10
5
March 13, 2006
HT36FA
and the other type is for wavetable code, which is addressed by the start address ST15~ST0. On the program type, WA17~WA0=PF3~PF0´213+PC12~PC0.
On t h e w a v e t abl e R O M t y p e , W A 1 7 ~W A 0 =
ST15~ST0´25.
Note:
0 0 0 0 H
0 0 0 8 H
0 0 0 C H
Program ROM address use word as address
unit, but wavetable ROM address use BYTE as
address unit.
D e v ic e in itia liz a tio n p r o g r a m
T im e r C o u n te r 0 in te r r u p t s u b r o u tin e
T im e r C o u n te r 1 in te r r u p t s u b r o u tin e
n 0 0 H
P ro g ra m
M e m o ry
L o o k - u p ta b le ( 2 5 6 w o r d s )
n F F H
Program Memory - ROM
The program memory is used to store the program instructions which are to be executed. It also contains
data, table, and interrupt entries, and is organized into
8192´16 bits, addressed by the bank pointer, program
counter and table pointer.
1 6 b its
N o te : n ra n g e s fro m
0 0 to 1 F .
Program Memory for Each Bank
Certain locations in the program memory of each bank
are reserved for special usage:
the TBLH. The Table Higher-order byte register
(TBLH) is read only. The Table Pointer (TBLP) is a
read/write register (07H), which indicates the table location. Before accessing the table, the location must
be placed in TBLP. The TBLH is read only and cannot
be restored. If the main routine and the ISR (Interrupt
Service Routine) both employ the table read instruction, the contents of the TBLH in the main routine are
likely to be changed by the table read instruction used
in the ISR. Errors can occur. In this case, using the table read instruction in the main routine and the ISR simultaneously should be avoided. However, if the
table read instruction has to be applied in both the
main routine and the ISR, the interrupt should be disabled prior to the table read instruction. It will not be
enabled until the TBLH has been backed up. All table
related instructions need 2 cycles to complete the operation. These areas may function as normal program
memory depending upon user requirements.
· Location 000H on bank0
This area is reserved for the initialization program. After chip reset, the program always begins execution at
location 000H on bank0.
· Location 008H
This area is reserved for the Timer Counter 0 interrupt
service program on each bank. If timer interrupt results
from a timer counter 0 overflow, and if the interrupt is enabled and the stack is not full, the program begins execution at location 008H corresponding to its bank.
· Location 00CH
This area is reserved for the Timer Counter 1 interrupt
service program on each bank. If a timer interrupt results from a Timer Counter 1 overflow, and if the interrupt is enabled and the stack is not full, the program
begins execution at location 00CH corresponding to
its bank.
· Bank pointer
· Table location
The program memory is organized into 16 banks and
each bank into 8192´16 bits of program ROM.
PF3~PF0 is used as the bank pointer. After an instruction has been executed to write data to the PF register
to select a different bank, note that the new bank will
not be selected immediately. It is not until the following
instruction has completed execution that the bank will
be actually selected. It should be note that the PF register has to be cleared before setting to output mode.
Any location in the ROM space can be used as
look-up tables. The instructions ²TABRDC [m]² (the
current page, 1 page=256 words) and ²TABRDL [m]²
(the last page) transfer the contents of the lower-order
byte to the specified data memory, and the
higher-order byte to TBLH (08H). Only the destination
of the lower-order byte in the table is well-defined, the
higher-order byte of the table word are transferred to
Instruction (s)
L o o k - u p ta b le ( 2 5 6 w o r d s )
1 F F F H
Table Location
*16
*15
*14
*13
*12
*10
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
TABRDC [m]
P16 P15 P14 P13 P12 P11 P10
P9
P8
@7
@6
@5
@4
@3
@2
@1
@0
TABRDL [m]
P16 P15 P14 P13
1
1
@7
@6
@5
@4
@3
@2
@1
@0
1
*11
1
1
Table Location
Note:
*16~*0: Bits of table location
P16~P8: Bits of current Program Counter
@7~@0: Bits of table pointer
P16~P13: Bits of bank PF3~PF0
Rev. 1.10
6
March 13, 2006
HT36FA
Wavetable ROM
0 0 H
The ST15~ST0 is used to defined the start address of
each sample on the wavetable and read the waveform
data from the location. HT36FA provides 18 output address lines from WA17~WA0, the ST15~ST0 is used to
locate the major 13 bits i.e. WA17~WA5 and the undefined data from WA4~WA0 is always set to 00000b. So
the start address of each sample have to be located at a
multiple of 32. Otherwise, the sample will not be read
out correctly because it has a wrong starting code.
M P 0
0 2 H
In d ir e c t A d d r e s s in g R e g is te r 1
0 3 H
M P 1
0 4 H
0 5 H
Stack Register - Stack
A C C
0 6 H
P C L
0 7 H
T B L P
0 8 H
T B L H
0 9 H
W D T S
0 A H
S T A T U S
0 B H
IN T C
0 C H
This is a special part of the memory which is used to
save the contents of the program counter only. The
stack is organized into 8 levels and is neither part of the
data nor part of the program space, and is neither readable nor writeable. The activated level is indexed by the
stack pointer (SP) and is neither readable nor writeable.
At a subroutine call or interrupt acknowledgment, the
contents of the program counter are pushed onto the
stack. At the end of a subroutine or an interrupt routine,
signaled by a return instruction (RET or RETI), the program counter is restored to its previous value from the
stack. After a chip reset, the SP will point to the top of the
stack.
0 D H
T M R 0 L
0 E H
T M R 0 C
S p e c ia l P u r p o s e
D a ta M e m o ry
0 F H
T M R 1 L
T M R 1 C
1 0 H
1 1 H
1 2 H
P A
1 3 H
P A C
1 4 H
P B
1 5 H
P B C
1 6 H
P C
1 7 H
1 8 H
P C C
1 9 H
1 A H
1 B H
P F
1 C H
If the stack is full and a non-masked interrupt takes
place, the interrupt request flag will be recorded but the
acknowledgment will be inhibited. When the stack
pointer is decremented (by RET or RETI), the interrupt
will be serviced. This feature prevents stack overflow allowing the programmer to use the structure more easily.
In a similar case, if the stack is full and a CALL is subsequently executed, a stack overflow occurs and the first
entry will be lost (only the most recent eight return address are stored).
1 D H
1 E H
1 F H
D A C
H ig h B y te ( D A H )
D A C L o w
D A C
B y te (D A L )
C o n tro l (D A C )
2 0 H
C h a n n e l N u m b e r S e le c t ( C H A N )
2 1 H
F r e q u e n c y N u m b e r H ig h B y te ( F r e q N H )
2 2 H
F re q u e n c y N u m b e r L o w B y te (F re q N L )
2 3 H
S ta r t A d d r e s s H ig h B y te ( A d d r H )
2 4 H
S ta rt A d d re s s L o w
2 5 H
R e p e a t N u m b e r H ig h B y te ( R e H )
2 6 H
R e p e a t N u m b e r L o w B y te (R e L )
2 7 H
V o lu m e C o n tr o l H ig h ( E N V )
B y te (A d d rL )
W a v e ta b le F u n c tio n
R e g is te r
2 8 H
Data Memory - RAM
The data memory is designed with 256 ´ 8 bits. The data
memory is divided into three functional groups, namely;
special function registers, wavetable function register
and general purpose data memory (208´8). Most of
which are readable/writeable, although some are read
only.
2 9 H
L e ft V o lu m e C o n tr o l ( L V C )
2 A H
2 B H
R ig h t V o lu m
C o n tro l (R V C )
: U n u s e d ,
re a d a s "0 0 "
2 F H
3 0 H
G e n e ra l P u rp o s e
D a ta M e m o ry
(2 0 8 B y te s )
The special function registers include the Indirect Addressing register 0 (00H), the Memory Pointer register 0
(MP0;01H), the Indirect Addressing register 1 (02H), the
Memory Pointer register 1 (MP1;03H), the Accumulator
(ACC;05H), the Program Counter Lower-byte register
(PCL;06H), the Table Pointer (TBLP;07H), the Table
Higher-order byte register (TBLH;08H), the Watchdog
Timer option Setting register (WDTS;09H), the Status
register (STATUS;0AH), the Interrupt Control register
(INTC;0BH), the Timer Counter 0 Lower-order byte register (TMR0L;0DH), the Timer Counter 0 Control register (TMR0C;0EH), the Timer Counter 1 Lower-order
byte register (TMR1L;10H), the Timer Counter 1 Control
Rev. 1.10
In d ir e c t A d d r e s s in g R e g is te r 0
0 1 H
F F H
RAM Mapping
register (TMR1C;11H), the I/O registers (PA;12H,
PB;14H, PC;16H) and the I/O control registers
(PAC;13H, PBC;15H, PCC;17H). The program ROM
bank select (PF;1CH). The DAC High byte (DAH;1DH).
The DAC low byte (DAL;1EH). The DAC control
(DAC;1FH). The wavetable function registers is defined
between 20H~2AH. The remaining space before the
7
March 13, 2006
HT36FA
· Rotation (RL, RR, RLC, RRC)
30H is reserved for future expanded usage and reading
these locations will return the result 00H. The general
purpose data memory, addressed from 30H to FFH, is
used for data and control information under instruction
command.
· Increment & Decrement (INC, DEC)
· Branch decision (SZ, SNZ, SIZ, SDZ ....)
The ALU not only saves the results of a data operation but
can also change the status register.
All data memory areas can handle arithmetic, logic, increment, decrement and rotate operations directly. Except for some dedicated bits, each bit in the data
memory can be set and reset by the ²SET [m].i² and
²CLR [m].i² instructions, respectively. They are also indirectly accessible through Memory pointer registers
(MP0:01H, MP1:03H).
Status Register - STATUS
This 8-bit register (0AH) contains the zero flag (Z), carry
flag (C), auxiliary carry flag (AC), overflow flag (OV),
power down flag (PDF) and Watchdog time-out flag
(TO). It also records the status information and controls the
operation sequence.
With the exception of the TO and PDF flags, bits in the
status register can be altered by instructions like any
other register. Any data written into the status register
will not change the TO or PDF flags. In addition it should
be noted that operations related to the status register
may give different results from those intended. The TO
and PDF flags can only be changed by system power
up, Watchdog Timer overflow, executing the ²HALT² instruction and clearing the Watchdog Timer.
Indirect Addressing Register
Location 00H and 02H are indirect addressing registers
that are not physically implemented. Any read/write operation of [00H] and [02H] access data memory pointed
to by MP0 (01H) and MP1 (03H), respectively. Reading
location 00H or 02H directly will return the result 00H.
And writing directly results in no operation.
The function of data movement between two indirect addressing registers, is not supported. The memory
pointer registers, MP0 and MP1, are 8-bit register which
can be used to access the data memory by combining
corresponding indirect addressing registers.
The Z, OV, AC and C flags generally reflect the status of
the latest operations.
In addition, on entering the interrupt sequence or executing a subroutine call, the status register will not be
automatically pushed onto the stack. If the contents of
status are important and the subroutine can corrupt the
status register, the programmer must take precautions
to save it properly.
Accumulator
The accumulator closely relates to ALU operations. It is
mapped to location 05H of the data memory and it can
operate with immediate data. The data movement between two data memory locations must pass through
the accumulator.
Interrupt
The HT36FA provides two internal timer counter interrupts on each bank. The Interrupt Control register
(INTC;0BH) contains the interrupt control bits that sets
the enable/disable and the interrupt request flags.
Arithmetic and Logic Unit - ALU
This circuit performs 8-bit arithmetic and logic operation.
The ALU provides the following functions:
Once an interrupt subroutine is serviced, all other interrupts will be blocked (by clearing the EMI bit). This
scheme may prevent any further interrupt nesting. Other
· Arithmetic operations (ADD, ADC, SUB, SBC, DAA)
· Logic operations (AND, OR, XOR, CPL)
Bit No.
Label
Function
0
C
C is set if an operation results in a carry during an addition operation or if a borrow does not
take place during a subtraction operation; otherwise C is cleared. Also it is affected by a rotate through carry instruction.
1
AC
AC is set if an operation results in a carry out of the low nibbles in addition or no borrow from
the high nibble into the low nibble in subtraction; otherwise AC is cleared.
2
Z
Z is set if the result of an arithmetic or logical operation is zero; otherwise Z is cleared.
3
OV
OV is set if an operation results in a carry into the highest-order bit but not a carry out of the
highest-order bit, or vice versa; otherwise OV is cleared.
4
PDF
PDF is cleared by either a system power-up or executing the ²CLR WDT² instruction.
PDF is set by executing the ²HALT² instruction.
5
TO
TO is cleared by a system power-up or executing the ²CLR WDT² or ²HALT² instruction.
TO is set by a WDT time-out.
6~7
¾
Unused bit, read as ²0²
Status (0AH) Register
Rev. 1.10
8
March 13, 2006
HT36FA
masked by resetting the EMI bit.
interrupt requests may occur during this interval but only
the interrupt request flag is recorded. If a certain interrupt needs servicing within the service routine, the programmer may set the EMI bit and the corresponding bit
of the INTC to allow interrupt nesting. If the stack is full,
the interrupt request will not be acknowledged, even if
the related interrupt is enabled, until the SP is decremented. If immediate service is desired, the stack must
be prevented from becoming full.
Interrupt Source
Priority
Vector
Timer Counter 0 overflow
1
08H
Timer Counter 1 overflow
2
0CH
The Timer Counter 0/1 interrupt request flag (T0F/T1F),
Enable Timer Counter 0/1 bit (ET0I/ET1I) and Enable
Master Interrupt bit (EMI) constitute an interrupt control
register (INTC) which is located at 0BH in the data memory. EMI, ET0I, ET1I are used to control the enabling/disabling of interrupts. These bits prevent the
requested interrupt from being serviced. Once the interrupt request flags (T0F, T1F) are set, they will remain in
the INTC register until the interrupts are serviced or
cleared by a software instruction.
All these kinds of interrupt have a wake-up capability. As
an interrupt is serviced, a control transfer occurs by
pushing the program counter onto the stack and then
branching to subroutines at specified locations in the
program memory. Only the program counter is pushed
onto the stack. If the contents of the register and Status
register (STATUS) are altered by the interrupt service
program which may corrupt the desired control sequence, then the programmer must save the contents
first.
It is recommended that a program does not use the
²CALL subroutine² within the interrupt subroutine. Because interrupts often occur in an unpredictable manner
or need to be serviced immediately in some applications, if only one stack is left and enabling the interrupt is
not well controlled, once the ²CALL subroutine² operates
in the interrupt subroutine, it may damage the original
control sequence.
The internal Timer Counter 0 interrupt is initialized by
setting the Timer Counter 0 interrupt request flag (T0F;
bit 5 of INTC), caused by a Timer Counter 0 overflow.
When the interrupt is enabled, and the stack is not full
and the T0F bit is set, a subroutine call to location 08H
will occur. The related interrupt request flag (T0F) will be
reset and the EMI bit cleared to disable further interrupts.
Oscillator Configuration
The HT36FA provides two types of oscillator circuit for
the system clock, i.e., RC oscillator and crystal oscillator.
No matter what type of oscillator, the signal divided by 2
is used for the system clock. The HALT mode stops the
system oscillator and ignores external signal to conserve power. If the RC oscillator is used, an external resistor between OSC1 and VSS is required. The system
clock, divided by 4, is available on OSC2 with pull-high
resistor, which can be used to synchronize external
logic. The RC oscillator provides the most cost effective
solution. However, the frequency of the oscillation may
The Timer Counter 1 interrupt is operated in the same
manner as Timer Counter 0. The related interrupt control bits ET1I and T1F of the Timer Counter 1 are bit 3
and bit 6 of the INTC, respectively.
During the execution of an interrupt subroutine, other interrupt acknowledgments are held until the ²RETI² instruction is executed or the EMI bit and the related
interrupt control bit are set to 1 (if the stack is not full). To
return from the interrupt subroutine, the ²RET² or
²RETI² instruction may be invoked. RETI will set the
EMI bit to enable an interrupt service, but RET will not.
O S C 1
Interrupts occurring in the interval between the rising
edges of two consecutive T2 pulses, will be serviced on
the latter of the two T2 pulses, if the corresponding interrupts are enabled. In the case of simultaneous requests
the priorities in the following table apply. These can be
V
fS
O S C 2
Y S
O S C 1
D D
/8
C r y s ta l O s c illa to r
O S C 2
R C
O s c illa to r
System Oscillator
Bit No.
Label
Function
0
EMI
1, 4, 7
¾
2
ET0I
Controls the Timer Counter 0 interrupt (1=enabled; 0=disabled)
3
ET1I
Controls the Timer Counter 1 interrupt (1=enabled; 0=disabled)
5
T0F
Internal Timer Counter 0 request flag (1=active; 0=inactive)
6
T1F
Internal Timer Counter 1 request flag (1=active; 0=inactive)
Controls the Master (Global) interrupt (1=enabled; 0=disabled)
Unused bit, read as ²0²
INTC (0BH) Register
Rev. 1.10
9
March 13, 2006
HT36FA
vary with VDD, temperature, and the chip itself due to
process variations. It is therefore, not suitable for timing
sensitive operations where accurate oscillator frequency is desired.
WS2
WS1
WS0
Division Ratio
0
0
0
1:1
0
0
1
1:2
On the other hand, if the crystal oscillator is selected, a
crystal across OSC1 and OSC2 is needed to provide the
feedback and phase shift required for the oscillator, and
no other external components are required. A resonator
may be connected between OSC1 and OSC2 to replace
the crystal and to get a frequency reference, but two external capacitors in OSC1 and OSC2 are required.
0
1
0
1:4
0
1
1
1:8
1
0
0
1:16
1
0
1
1:32
1
1
0
1:64
1
1
1
1:128
The WDT oscillator is a free running on-chip RC oscillator, and no external components are required. Even if
the system enters the Power Down Mode, the system
clock is stopped, but the WDT oscillator still works with a
period of approximately 78ms. The WDT oscillator can
be disabled by mask option to conserve power.
If the device operates in a noisy environment, using the
on-chip RC oscillator (WDT OSC) is strongly recommended, since the HALT will stop the system clock.
The WDT overflow under normal operation will initialize
a ²chip reset² and set the status bit TO. Whereas in the
HALT mode, the overflow will initialize a ²warm reset²
only the Program Counter and SP are reset to zero. To
clear the WDT contents (including the WDT prescaler ),
3 methods are implemented; external reset (a low level
to RES), software instructions, or a ²HALT² instruction.
The software instructions include ²CLR WDT² and the
other set - ²CLR WDT1² and ²CLR WDT2². Of these
two types of instructions, only one can be active depending on the mask option - ²CLR WDT times selection option². If the ²CLR WDT² is selected (i.e. CLRWDT
times equal one), any execution of the ²CLR WDT² instruction will clear the WDT. In case ²CLR WDT1² and
²CLR WDT2² are chosen (i.e. CLRWDT times equal
two), these two instructions must be executed to clear
the WDT; otherwise, the WDT may reset the chip because of time-out.
Watchdog Timer - WDT
The WDT clock source is implemented by a dedicated
RC oscillator (WDT oscillator) or instruction clock (system clock of the MCU divided by 4), determined by mask
options. This timer is designed to prevent a software
malfunction or sequence jumping to an unknown location with unpredictable results. The Watchdog Timer can
be disabled by mask option. If the Watchdog Timer is
disabled, all the executions related to the WDT result in
no operation.
Once the internal WDT oscillator (RC oscillator with a
period of 78ms normally) is selected, it is first divided by
256 (8-stages) to get the nominal time-out period of approximately 20ms. This time-out period may vary with
temperature, VDD and process variations. By invoking
the WDT prescaler, longer time-out periods can be realized. Writing data to WS2, WS1, WS0 (bit 2,1,0 of the
WDTS) can give different time-out periods. If WS2,
WS1, WS0 all equal to 1, the division ratio is up to 1:128,
and the maximum time-out period is 2.6 seconds.
Power Down Operation - HALT
The HALT mode is initialized by a ²HALT² instruction
and results in the following...
· The system oscillator will turn off but the WDT oscilla-
If the WDT oscillator is disabled, the WDT clock may still
come from the instruction clock and operate in the same
manner except that in the HALT state the WDT may stop
counting and lose its protecting purpose. In this situation
the logic can only be restarted by external logic. The
high nibble and bit 3 of the WDTS are reserved for user
defined flags, and the programmer may use these flags
to indicate some specified status.
S y s te m
tor keeps running (If the WDT oscillator is selected).
Watchdog Timer - WDT
· The contents of the on-chip RAM and registers remain
unchanged
· The WDT and WDT prescaler will be cleared and
starts to count again (if the clock comes from the WDT
oscillator).
C lo c k /8
W D T
O S C
W D T P r e s c a le r
M a s k
O p tio n
S e le c t
8 - b it C o u n te r
7 - b it C o u n te r
8 -to -1 M U X
W S 0 ~ W S 2
W D T T im e - o u t
Watchdog Timer
Rev. 1.10
10
March 13, 2006
HT36FA
· All I/O ports maintain their original status.
TO
PDF
· The PDF flag is set and the TO flag is cleared.
0
0
RES reset during power-up
· The HALT pin will output a high level signal to disable
u
u
RES reset during normal operation
0
1
RES wake-up HALT
1
u
WDT time-out during normal operation
1
1
WDT wake-up HALT
the external ROM.
The system can leave the HALT mode by means of an
external reset, an interrupt, an external falling edge signal on port A or a WDT overflow. An external reset
causes a device initialization and the WDT overflow performs a ²warm reset². By examining the TO and PDF
flags, the cause for a chip reset can be determined. The
PDF flag is cleared when there is a system power-up or by
executing the ²CLR WDT² instruction and it is set when a
²HALT² instruction is executed. The TO flag is set if the
WDT time-out occurs, and causes a wake-up that only resets the Program Counter and SP, the others remain in
their original status.
RESET Conditions
Note: ²u² stands for ²unchanged²
To guarantee that the system oscillator has started and
stabilized, the SST (System Start-up Timer) provides an
extra-delay of 1024 system clock pulses during system
power up or when the system awakes from a HALT
state.
When a system power-up occurs, the SST delay is
added during the reset period. But when the reset comes from the RES pin, the SST delay is disabled. Any
wake-up from HALT will enable the SST delay.
The port A wake-up and interrupt methods can be considered as a continuation of normal execution. Each bit
in port A can be independently selected to wake-up the
device by mask option. Awakening from an I/O port stimulus, the program will resume execution of the next instruction. If awakening from an interrupt, two sequences
may occur. If the related interrupts is disabled or the interrupts is enabled but the stack is full, the program will
resume execution at the next instruction. If the interrupt
is enabled and the stack is not full, a regular interrupt response takes place.
The functional units chip reset status are shown below.
Once a wake-up event occurs, it takes 1024 tSYS (system clock period) to resume to normal operation. In
other words, a dummy cycle period will be inserted after
the wake-up. If the wake-up results from an interrupt acknowledge, the actual interrupt subroutine will be delayed by one more cycle. If the wake-up results in next
instruction execution, this will execute immediately after
a dummy period has finished. If an interrupt request flag
is set to ²1² before entering the HALT mode, the
wake-up function of the related interrupt will be disabled.
Program Counter
000H
Interrupt
Disable
Prescaler
Clear
WDT
Clear. After master reset,
WDT begins counting
Timer Counter (0/1)
Off
Input/output ports
Input mode
Stack Pointer
Points to the top of stack
V
D D
R E S
Reset Circuit
To minimize power consumption, all I/O pins should be
carefully managed before entering the HALT status.
V D D
R E S
Reset
tS
S T
S S T T im e - o u t
There are 3 ways in which a reset can occur:
C h ip R e s e t
· RES reset during normal operation
Reset Timing Chart
· RES reset during HALT
· WDT time-out reset during normal operation
H A L T
W D T
The WDT time-out during HALT is different from other
chip reset conditions, since it can perform a ²warm re set² that just resets the Program Counter and SP, leaving the other circuits to maintain their state. Some registers remain unchanged during any other reset
conditions. Most registers are reset to the ²initial condition² when the reset conditions are met. By examining
the PDF and TO flags, the program can distinguish between different ²chip resets².
Rev. 1.10
W D T
W a rm
R e s e t
T im e - o u t
R e s e t
R E S
O S C I
S S T
1 0 -s ta g e
R ip p le C o u n te r
C o ld
R e s e t
P o w e r - o n D e te c tin g
Reset Configuration
11
March 13, 2006
HT36FA
The registers status is summarized in the following table:
Reset
(Power-on)
WDT Time-out
(Normal Operation)
RES Reset
(Normal Operation)
RES Reset
(HALT)
WDT Time-out
(HALT)*
MP0
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
MP1
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
ACC
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
Register
Program Counter
0000H
0000H
0000H
0000H
0000H
TBLP
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TBLH
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
WDTS
0000 0111
0000 0111
0000 0111
0000 0111
uuuu uuuu
STATUS
--00 xxxx
--1u uuuu
--uu uuuu
--01 uuuu
--11 uuuu
INTC
-00- 00-0
-00- 00-0
-00- 00-0
-00- 00-0
-uu- uu-u
TMR0L
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TMR0C
00-0 1000
00-0 1000
00-0 1000
00-0 1000
uu-u 1uuu
TMR1L
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TMR1C
00-0 1000
00-0 1000
00-0 1000
00-0 1000
uu-u 1uuu
PA
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PAC
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PB
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PBC
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PC
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PCC
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PF
---- 0000
---- 0000
---- 0000
---- 0000
---- uuuu
DAH
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
DAL
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
DAC
---- -000
---- -000
---- -000
---- -000
---- -uuu
CHAN
00-- --00
uu-- --uu
uu-- --uu
uu-- --uu
uu-- --uu
FreqNH
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
FreqNL
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
AddrH
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
AddrL
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
ReH
x--x xxxx
u--u uuuu
u--u uuuu
u--u uuuu
u--u uuuu
ReL
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
ENV
x-xx --xx
u-uu --uu
u-uu --uu
u-uu --uu
u-uu --uu
LVC
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
RVC
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
Note:
²*² stands for warm reset
²u² stands for unchanged
²x² stands for unknown
²-² stands for unused
Rev. 1.10
12
March 13, 2006
HT36FA
D a ta B u s
Timer 0/1
Timer 0 is an 8-bit counter, and its clock source comes
from the system clock divided by an 8-stage prescaler.
There are two registers related to Timer 0; TMR0L
(0DH) and TMR0C (0EH). One physical registers are
mapped to TMR0L location; writing TMR0L makes the
starting value be placed in the Timer 0 preload register
and reading the TMR0 gets the contents of the Timer 0
counter. The TMR0C is a control register, which defines
the division ration of the prescaler and counting enable
or disable.
S y s te m
C lo c k /8
T O N
0
0
0
SYS CLK/16
0
0
1
SYS CLK/32
0
1
0
SYS CLK/64
0
1
1
SYS CLK/128
1
0
0
SYS CLK/256
1
0
1
SYS CLK/512
1
1
0
SYS CLK/1024
1
1
1
SYS CLK/2048
Each I/O line has its own control register (PAC, PBC,
PCC0~3) to control the input/output configuration. With
this control register, CMOS output or Schmitt trigger input with or without pull-high resistor (mask option) structures can be reconfigured dynamically under software
control. To function as an input, the corresponding latch
of the control register must write a ²1². The pull-high resistance will exhibit automatically if the pull-high option
is selected. The input source also depends on the control register. If the control register bit is ²1², input will
read the pad state. If the control register bit is ²0², the
contents of the latches will move to the internal bus. The
latter is possible in ²read-modify-write² instruction. For
output function, CMOS is the only configuration. These
control registers are mapped to locations 13H, 15H and
17H.
After a chip reset, these input/output lines remain at high
levels or floating (mask option). Each bit of these input/output latches can be set or cleared by the ²SET
[m].i² or ²CLR [m].i² (m=12H, 14H or 16H) instruction.
TMR0C Bit 4 to enable/disable timer counting
(1=enable; 0=disable)
Some instructions first input data and then follow the
output operations. For example, the ²SET [m].i², ²CLR
[m].i², ²CPL [m]² and ²CPLA [m]² instructions read the
entire port states into the CPU, execute the defined operations (bit-operation), and then write the results back
to the latches or the accumulator. Each line of port A has
the capability to wake-up the device.
TMR0C Bit 3, always write ²0².
TMR0C Bit 5, always write ²0².
TMR0C Bit 6, always write ²0².
TMR0C Bit 7, always write ²1².
Rev. 1.10
O v e r flo w
There are 20 bidirectional input/output lines labeled
from PA to PC0~3, which are mapped to the data memory of [12H], [14H], [16H], respectively. All these I/O
ports can be used for input and output operations. For
input operation, these ports are non-latching, that is, the
inputs must be ready at the T2 rising edge of instruction
²MOV A,[m]² (m=12H, 14H or 16H). For output operation, all data is latched and remains unchanged until the
output latch is rewritten.
T0F
B0
T im e r 0 /1
Input/Output Ports
There are two registers related to the Timer Counter1;
TMR1L(10H), TMR1C(11H). The Timer Counter 1 operates in the same manner as Timer Counter 0.
B1
R e lo a d
Timer 0/1
One the Timer 0 starts counting, it will count from the
current contents in the counter to FFH. Once an overflow occurs, the counter is reloaded from a preload register, and generates an interrupt request flag (T0F; bit 2
of INTCH). To enable the counting operation, the timer
On bit (TON; bit 4 of TMR0C) should be set to ²1². For
proper operation, bit 7 of TMR0C should be set to ²1²
and bit 3, bit 6 should be set to ²0².
B2
T im e r 0 /1
P r e lo a d R e g is te r
T 0 F
Writing data to B2, B1 and B0 (bits 2, 1, 0 of TMR0C)
can yield various clock sources.
TMR0C/TMR1C
8 -s ta g e
P r e s c a le r
13
March 13, 2006
HT36FA
C o n tr o l B it
Q
D
D a ta B u s
W r ite C o n tr o l R e g is te r
V
Q
C K
V
S
W e a k
P u ll- u p
D D
C h ip R e s e t
M a s k O p tio n
R e a d C o n tr o l R e g is te r
D a ta B it
Q
D
W r ite I/O
C K
S
I/O
L in e
Q
M
R e a d I/O
S y s te m
D D
U
X
W a k e -U p
Input/Output Ports
Channel Wavetable Synthesizer
D7
D6
D5
D4
D3
D2
D1
D0
1DH
Name
DAC high byte (no default value)
Function
DA15
DA14
DA13
DA12
DA11
DA10
DA9
DA8
1EH
DAC low byte (no default value)
DA7
DA6
DA5
DA4
DA3
DA2
DA1
DA0
1FH
DAON=1: DAC ON
DAON=0: DAC OFF (default)
SELW=1: DAC data from wavetable
SELW=0: DAC data from MCU
¾
¾
¾
¾
¾
Left
DAON
SELW
Right
20H
Channel number selection
VM
FR
CH1
CH0
21H
High byte frequency number
BL3
BL2
BL1
BL0
FR11
FR10
FR9
FR8
22H
Low byte frequency number
FR7
FR6
FR5
FR4
FR3
FR2
FR1
FR0
23H
High byte start address
ST15
ST14
ST13
ST12
ST11
ST10
ST9
ST8
24H
Low byte start address
ST7
ST6
ST5
ST4
ST3
ST2
ST1
ST0
25H
Wave bit select,
High byte repeat number
WBS
RE12
RE11
RE10
RE9
RE8
26H
Low byte repeat number
RE7
RE5
RE4
RE3
RE2
RE1
RE0
27H
Envelope control,
Volume control
A_R
VL9
VL8
VR9
VR8
29H
Left Volume control
VL7
VL6
VL5
VL4
VL3
VL2
VL1
VL0
2AH
Right Volume control
VR7
VR6
VR5
VR4
VR3
VR2
VR1
VR0
RE6
28H
Unused
2BH~2FH
Unused
30H~FFH Data memory (RAM)
General purpose data memory (same as 8-Bit MCU)
Memory Map (1DH~FFH) Register
Note:
²¾² No function, read only, read as ²0².
Unused: No function, read only, read as ²0².
· CH1~CH0 channel number selection
register will be updated on this selected channel.
There are two modes that can be selected to reduce
the process of setting the register. Please refer to the
statements of the following table:
The HT36FA has a built-in 8 output channels and
CH1~CH0 is used to define which channel is selected.
When this register is written to, the wavetable synthesizer will automatically output the dedicated PCM
code. So this register is also used as a start playing
key and it has to be written to after all the other
wavetable function registers are already defined.
· Change parameter selection
VM
FR
0
0
Update all the parameter
Function
0
1
Only update the frequency number
1
0
Only update the volume
These two bits, VM and FR, are used to define which
Rev. 1.10
14
March 13, 2006
HT36FA
· Output frequency definition
· Repeat number definition
The repeat number is used to define the address
which is the repeat point of the sample. When the repeat number is defined, it will be output from the start
code to the end code once and always output the
range between the repeat address to the end code
(80H) until the volume become close.
The RE12~RE0 is used to calculate the repeat address of the PCM code. The process for setting the
RE12~RE0 is to write the 2¢s complement of the repeat length to RE12~RE0, with the highest carry ignored. The HT36FA will get the repeat address by
adding the RE12~RE0 to the address of the end code,
then jump to the address to repeat this range.
The data on BL3~BL0 and FR11~FR0 are used to define the output speed of the PCM file, i.e. it can be
used to generate the tone scale. When the FR11~FR0
is 800H and BL3~BL0 is 6H, each sample data of the
PCM code will be sent out sequentially.
When the fOSC is 6.4MHz, the formula of a tone frequency is:
25kHz FR11 ~ FR0
fOUT= fRECORD x
x (17 - BL3~BL0)
SR
2
where fOUT is the output signal frequency, fRECORD and
SR is the frequency and sampling rate on the sample
code, respectively.
So if a voice code of C3 has been recorded which has
the fRECORD of 261Hz and the SR of 11025Hz, the tone
frequency (fOUT) of G3: fOUT=98Hz.
Can be obtained by using the fomula:
25kHz
FR11 ~ FR0
98Hz= 261Hz x
x
11025Hz 2 (17 - BL3~BL0)
A pair of the values FR11~FR0 and BL3~BL0 can be
determined when the fOSC is 6.4MHz.
· Volume control
The HT36FA provides the volume control independently. The volume are controlled by VR9~VR0, respectively. The chip provides 1024 levels of
controllable volume, the 000H is the maximum and
3FFH is the minimum output volume.
· The PCM code definition
· Start address definition
The HT36FA can only solve the voice format of the
signed 8-bit or 12-bit raw PCM. And the MCU will take
the voice code 80H as the end code.
So each PCM code section must be ended with the
end code 80H.
The HT36FA provides two address types for extended
use, one is the program ROM address which is program counter corresponding with PF value, the other
is the start address of the PCM code.
The ST15~ST0 is used to define the start address of
each PCM code and reads the waveform data from
this location. The HT36FA provides 16 input data lines
from WA17~WA0, the ST15~ST0 is used to locate the
major 12 bits .e. WA17~WA5 and the undefined data
from WA4~WA0 is always set as 00000b. In other
words, the WA17~WA0=ST15~ST0´25. So each
PCM code has to be located at a multiple of 32. Otherwise, the PCM code will not be read out correctly because it has a wrong start code.
· Digital to Analog Converter - DAC
The HT36FA provides one 16-bit voltage type DAC
device controlled by the MCU or Wavetable Synthesizer for driving the external speaker through an external NPN transistor. It is in fact an optional object used
for Wavetable Synthesizer DAC or general DAC, this
is chosen by Mask Option and DAC control register. If
the general DAC is chosen for application, then the
Wavetable Synthesizer is disabled since the DAC is
taken up and controlled by the MCU. If general DAC is
selected, the programmer must write the voice data to
register DAL and DAH to get the corresponding analog data. If Mask Option enables the DAC register and
the SELW, then the following table comes useful.
· Waveform format definition
The HT36FA accepts two waveform formats to ensure
a more economical data space. WBS is used to define
the sample format of each PCM code.
¨
WBS=0 means the sample format is 8-bit
¨
WBS=1 means the sample format is 12-bit
The 12-bit sample format allocates location to each
sample data. Please refer to the waveform format
statement as shown below.
8 - B it
1 B
2 B
3 B
4 B
5 B
6 B
7 B
1 H
1 M
1 L
2 L
2 H
2 M
3 H
Label
¾
Bit2
SELWL
SELWL=1, left channel DAC
data from wavetable
SELWL=0, left channel DAC
data from MCU (Default)
Bit1
DAON
DAON=1: DAC ON
DAON=0: DAC OFF (Default)
8 B
A s a m p lin g d a ta c o d e ; B m e a n s o n e d a ta b y te .
1 2 - B it
Bit No.
Bit7~Bit3
3 M
3 L
Bit0
A s a m p lin g d a ta c o d e
N o te : " 1 H " H ig h N ib b le
" 1 M " M id d le N ib b le
" 1 L " L o w N ib b le
Function
No used
SELWR=1, Right Channel
DAC data from Wavetable
SELWR
SELWR=0, Right Channel
DAC data from MCU (Default)
Waveform Format
Rev. 1.10
15
March 13, 2006
HT36FA
Mask Option
No.
Mask Option
Function
1
WDT source
2
CLRWDT times One time, two times (CLR WDT1/WDT2)
On-chip RC/Instruction clock/ disable WDT
3
Wake-up
4
Pull-High
PA, PB, PC input
5
OSC mode
Crystal or Resistor type
6
LVR
Enable/disable
7
LVD
2.2V/3.3V
PA only
Application Circuit
V
D D
1 0 W
V D D
4 7 m F
V D D A
0 .1 m F
O S C 1
O S C 2
V
D D
4 7 m F
L C H
2 0 k W
1 0 m F
0 .1 m F
2
IN
V re f
3
8
V D D
O U T N
1
H T 8 2 V 7 3 3
V S S
4
5
S P K
8 W
7
O U T P
C E
V
V
D D
4 7 m F
D D
R C H
2 0 k W
1 0 0 k W
R E S
V S S A
0 .1 m F
1 0 m F
V S S
0 .1 m F
2
IN
V re f
3
8
V D D
H T 8 2 V 7 3 3
V S S
4
5
O U T N
1
S P K
8 W
7
O U T P
C E
H T 3 6 F A
V
D D
1 0 W
V D D
4 7 m F
V D D A
0 .1 m F
V
D D
O S C 1
6 M H z
O S C 2
L C H
S P K
8 W
R 1
1 k W
R 2
7 5 0 W
V
V
D D
1 0 0 k W
R C H
R E S
0 .1 m F
D D
S P K
8 W
R 1
1 k W
R 2
7 5 0 W
V S S A
V S S
H T 3 6 F A
N o te : R 1 > R 2
Rev. 1.10
16
March 13, 2006
HT36FA
Instruction Set Summary
Description
Instruction
Cycle
Flag
Affected
Add data memory to ACC
Add ACC to data memory
Add immediate data to ACC
Add data memory to ACC with carry
Add ACC to data memory with carry
Subtract immediate data from ACC
Subtract data memory from ACC
Subtract data memory from ACC with result in data memory
Subtract data memory from ACC with carry
Subtract data memory from ACC with carry and result in data memory
Decimal adjust ACC for addition with result in data memory
1
1(1)
1
1
1(1)
1
1
1(1)
1
1(1)
1(1)
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
C
1
1
1
1(1)
1(1)
1(1)
1
1
1
1(1)
1
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Increment data memory with result in ACC
Increment data memory
Decrement data memory with result in ACC
Decrement data memory
1
1(1)
1
1(1)
Z
Z
Z
Z
Rotate data memory right with result in ACC
Rotate data memory right
Rotate data memory right through carry with result in ACC
Rotate data memory right through carry
Rotate data memory left with result in ACC
Rotate data memory left
Rotate data memory left through carry with result in ACC
Rotate data memory left through carry
1
1(1)
1
1(1)
1
1(1)
1
1(1)
None
None
C
C
None
None
C
C
Move data memory to ACC
Move ACC to data memory
Move immediate data to ACC
1
1(1)
1
None
None
None
Clear bit of data memory
Set bit of data memory
1(1)
1(1)
None
None
Mnemonic
Arithmetic
ADD A,[m]
ADDM A,[m]
ADD A,x
ADC A,[m]
ADCM A,[m]
SUB A,x
SUB A,[m]
SUBM A,[m]
SBC A,[m]
SBCM A,[m]
DAA [m]
Logic Operation
AND A,[m]
OR A,[m]
XOR A,[m]
ANDM A,[m]
ORM A,[m]
XORM A,[m]
AND A,x
OR A,x
XOR A,x
CPL [m]
CPLA [m]
AND data memory to ACC
OR data memory to ACC
Exclusive-OR data memory to ACC
AND ACC to data memory
OR ACC to data memory
Exclusive-OR ACC to data memory
AND immediate data to ACC
OR immediate data to ACC
Exclusive-OR immediate data to ACC
Complement data memory
Complement data memory with result in ACC
Increment & Decrement
INCA [m]
INC [m]
DECA [m]
DEC [m]
Rotate
RRA [m]
RR [m]
RRCA [m]
RRC [m]
RLA [m]
RL [m]
RLCA [m]
RLC [m]
Data Move
MOV A,[m]
MOV [m],A
MOV A,x
Bit Operation
CLR [m].i
SET [m].i
Rev. 1.10
17
March 13, 2006
HT36FA
Instruction
Cycle
Flag
Affected
Jump unconditionally
Skip if data memory is zero
Skip if data memory is zero with data movement to ACC
Skip if bit i of data memory is zero
Skip if bit i of data memory is not zero
Skip if increment data memory is zero
Skip if decrement data memory is zero
Skip if increment data memory is zero with result in ACC
Skip if decrement data memory is zero with result in ACC
Subroutine call
Return from subroutine
Return from subroutine and load immediate data to ACC
Return from interrupt
2
1(2)
1(2)
1(2)
1(2)
1(3)
1(3)
1(2)
1(2)
2
2
2
2
None
None
None
None
None
None
None
None
None
None
None
None
None
Read ROM code (current page) to data memory and TBLH
Read ROM code (last page) to data memory and TBLH
2(1)
2(1)
None
None
No operation
Clear data memory
Set data memory
Clear Watchdog Timer
Pre-clear Watchdog Timer
Pre-clear Watchdog Timer
Swap nibbles of data memory
Swap nibbles of data memory with result in
Enter Power Down Mode
1
1(1)
1(1)
1
1
1
1(1)
1
1
None
None
None
TO,PDF
TO(4),PDF(4)
TO(4),PDF(4)
None
None
TO,PDF
Mnemonic
Description
Branch
JMP addr
SZ [m]
SZA [m]
SZ [m].i
SNZ [m].i
SIZ [m]
SDZ [m]
SIZA [m]
SDZA [m]
CALL addr
RET
RET A,x
RETI
Table Read
TABRDC [m]
TABRDL [m]
Miscellaneous
NOP
CLR [m]
SET [m]
CLR WDT
CLR WDT1
CLR WDT2
SWAP [m]
SWAPA [m]
HALT
Note:
x: Immediate data
m: Data memory address
A: Accumulator
i: 0~7 number of bits
addr: Program memory address
Ö: Flag is affected
-: Flag is not affected
(1)
: If a loading to the PCL register occurs, the execution cycle of instructions will be delayed for one more cycle
(four system clocks).
(2)
: If a skipping to the next instruction occurs, the execution cycle of instructions will be delayed for one more
cycle (four system clocks). Otherwise the original instruction cycle is unchanged.
(3) (1)
:
(4)
Rev. 1.10
and (2)
: The flags may be affected by the execution status. If the Watchdog Timer is cleared by executing the
²CLR WDT1² or ²CLR WDT2² instruction, the TO and PDF are cleared.
Otherwise the TO and PDF flags remain unchanged.
18
March 13, 2006
HT36FA
Instruction Definition
ADC A,[m]
Add data memory and carry to the accumulator
Description
The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the accumulator.
Operation
ACC ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADCM A,[m]
Add the accumulator and carry to data memory
Description
The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the specified data memory.
Operation
[m] ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADD A,[m]
Add data memory to the accumulator
Description
The contents of the specified data memory and the accumulator are added. The result is
stored in the accumulator.
Operation
ACC ¬ ACC+[m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADD A,x
Add immediate data to the accumulator
Description
The contents of the accumulator and the specified data are added, leaving the result in the
accumulator.
Operation
ACC ¬ ACC+x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADDM A,[m]
Add the accumulator to the data memory
Description
The contents of the specified data memory and the accumulator are added. The result is
stored in the data memory.
Operation
[m] ¬ ACC+[m]
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
19
March 13, 2006
HT36FA
AND A,[m]
Logical AND accumulator with data memory
Description
Data in the accumulator and the specified data memory perform a bitwise logical_AND operation. The result is stored in the accumulator.
Operation
ACC ¬ ACC ²AND² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
AND A,x
Logical AND immediate data to the accumulator
Description
Data in the accumulator and the specified data perform a bitwise logical_AND operation.
The result is stored in the accumulator.
Operation
ACC ¬ ACC ²AND² x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
ANDM A,[m]
Logical AND data memory with the accumulator
Description
Data in the specified data memory and the accumulator perform a bitwise logical_AND operation. The result is stored in the data memory.
Operation
[m] ¬ ACC ²AND² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
CALL addr
Subroutine call
Description
The instruction unconditionally calls a subroutine located at the indicated address. The
program counter increments once to obtain the address of the next instruction, and pushes
this onto the stack. The indicated address is then loaded. Program execution continues
with the instruction at this address.
Operation
Stack ¬ Program Counter+1
Program Counter ¬ addr
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
CLR [m]
Clear data memory
Description
The contents of the specified data memory are cleared to 0.
Operation
[m] ¬ 00H
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
20
March 13, 2006
HT36FA
CLR [m].i
Clear bit of data memory
Description
The bit i of the specified data memory is cleared to 0.
Operation
[m].i ¬ 0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
CLR WDT
Clear Watchdog Timer
Description
The WDT is cleared (clears the WDT). The power down bit (PDF) and time-out bit (TO) are
cleared.
Operation
WDT ¬ 00H
PDF and TO ¬ 0
Affected flag(s)
TO
PDF
OV
Z
AC
C
0
0
¾
¾
¾
¾
CLR WDT1
Preclear Watchdog Timer
Description
Together with CLR WDT2, clears the WDT. PDF and TO are also cleared. Only execution
of this instruction without the other preclear instruction just sets the indicated flag which implies this instruction has been executed and the TO and PDF flags remain unchanged.
Operation
WDT ¬ 00H*
PDF and TO ¬ 0*
Affected flag(s)
TO
PDF
OV
Z
AC
C
0*
0*
¾
¾
¾
¾
CLR WDT2
Preclear Watchdog Timer
Description
Together with CLR WDT1, clears the WDT. PDF and TO are also cleared. Only execution
of this instruction without the other preclear instruction, sets the indicated flag which implies this instruction has been executed and the TO and PDF flags remain unchanged.
Operation
WDT ¬ 00H*
PDF and TO ¬ 0*
Affected flag(s)
TO
PDF
OV
Z
AC
C
0*
0*
¾
¾
¾
¾
CPL [m]
Complement data memory
Description
Each bit of the specified data memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice-versa.
Operation
[m] ¬ [m]
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
21
March 13, 2006
HT36FA
CPLA [m]
Complement data memory and place result in the accumulator
Description
Each bit of the specified data memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice-versa. The complemented result
is stored in the accumulator and the contents of the data memory remain unchanged.
Operation
ACC ¬ [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
DAA [m]
Decimal-Adjust accumulator for addition
Description
The accumulator value is adjusted to the BCD (Binary Coded Decimal) code. The accumulator is divided into two nibbles. Each nibble is adjusted to the BCD code and an internal
carry (AC1) will be done if the low nibble of the accumulator is greater than 9. The BCD adjustment is done by adding 6 to the original value if the original value is greater than 9 or a
carry (AC or C) is set; otherwise the original value remains unchanged. The result is stored
in the data memory and only the carry flag (C) may be affected.
Operation
If ACC.3~ACC.0 >9 or AC=1
then [m].3~[m].0 ¬ (ACC.3~ACC.0)+6, AC1=AC
else [m].3~[m].0 ¬ (ACC.3~ACC.0), AC1=0
and
If ACC.7~ACC.4+AC1 >9 or C=1
then [m].7~[m].4 ¬ ACC.7~ACC.4+6+AC1,C=1
else [m].7~[m].4 ¬ ACC.7~ACC.4+AC1,C=C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
DEC [m]
Decrement data memory
Description
Data in the specified data memory is decremented by 1.
Operation
[m] ¬ [m]-1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
DECA [m]
Decrement data memory and place result in the accumulator
Description
Data in the specified data memory is decremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC ¬ [m]-1
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
22
March 13, 2006
HT36FA
HALT
Enter Power Down Mode
Description
This instruction stops program execution and turns off the system clock. The contents of
the RAM and registers are retained. The WDT and prescaler are cleared. The power down
bit (PDF) is set and the WDT time-out bit (TO) is cleared.
Operation
Program Counter ¬ Program Counter+1
PDF ¬ 1
TO ¬ 0
Affected flag(s)
TO
PDF
OV
Z
AC
C
0
1
¾
¾
¾
¾
INC [m]
Increment data memory
Description
Data in the specified data memory is incremented by 1
Operation
[m] ¬ [m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
INCA [m]
Increment data memory and place result in the accumulator
Description
Data in the specified data memory is incremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC ¬ [m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
JMP addr
Directly jump
Description
The program counter are replaced with the directly-specified address unconditionally, and
control is passed to this destination.
Operation
Program Counter ¬addr
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
MOV A,[m]
Move data memory to the accumulator
Description
The contents of the specified data memory are copied to the accumulator.
Operation
ACC ¬ [m]
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
23
March 13, 2006
HT36FA
MOV A,x
Move immediate data to the accumulator
Description
The 8-bit data specified by the code is loaded into the accumulator.
Operation
ACC ¬ x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
MOV [m],A
Move the accumulator to data memory
Description
The contents of the accumulator are copied to the specified data memory (one of the data
memories).
Operation
[m] ¬ACC
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
NOP
No operation
Description
No operation is performed. Execution continues with the next instruction.
Operation
Program Counter ¬ Program Counter+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
OR A,[m]
Logical OR accumulator with data memory
Description
Data in the accumulator and the specified data memory (one of the data memories) perform a bitwise logical_OR operation. The result is stored in the accumulator.
Operation
ACC ¬ ACC ²OR² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
OR A,x
Logical OR immediate data to the accumulator
Description
Data in the accumulator and the specified data perform a bitwise logical_OR operation.
The result is stored in the accumulator.
Operation
ACC ¬ ACC ²OR² x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
ORM A,[m]
Logical OR data memory with the accumulator
Description
Data in the data memory (one of the data memories) and the accumulator perform a
bitwise logical_OR operation. The result is stored in the data memory.
Operation
[m] ¬ACC ²OR² [m]
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
24
March 13, 2006
HT36FA
RET
Return from subroutine
Description
The program counter is restored from the stack. This is a 2-cycle instruction.
Operation
Program Counter ¬ Stack
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RET A,x
Return and place immediate data in the accumulator
Description
The program counter is restored from the stack and the accumulator loaded with the specified 8-bit immediate data.
Operation
Program Counter ¬ Stack
ACC ¬ x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RETI
Return from interrupt
Description
The program counter is restored from the stack, and interrupts are enabled by setting the
EMI bit. EMI is the enable master (global) interrupt bit.
Operation
Program Counter ¬ Stack
EMI ¬ 1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RL [m]
Rotate data memory left
Description
The contents of the specified data memory are rotated 1 bit left with bit 7 rotated into bit 0.
Operation
[m].(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
[m].0 ¬ [m].7
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RLA [m]
Rotate data memory left and place result in the accumulator
Description
Data in the specified data memory is rotated 1 bit left with bit 7 rotated into bit 0, leaving the
rotated result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
ACC.0 ¬ [m].7
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
25
March 13, 2006
HT36FA
RLC [m]
Rotate data memory left through carry
Description
The contents of the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the carry bit; the original carry flag is rotated into the bit 0 position.
Operation
[m].(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
[m].0 ¬ C
C ¬ [m].7
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
RLCA [m]
Rotate left through carry and place result in the accumulator
Description
Data in the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the
carry bit and the original carry flag is rotated into bit 0 position. The rotated result is stored
in the accumulator but the contents of the data memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
ACC.0 ¬ C
C ¬ [m].7
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
RR [m]
Rotate data memory right
Description
The contents of the specified data memory are rotated 1 bit right with bit 0 rotated to bit 7.
Operation
[m].i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
[m].7 ¬ [m].0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RRA [m]
Rotate right and place result in the accumulator
Description
Data in the specified data memory is rotated 1 bit right with bit 0 rotated into bit 7, leaving
the rotated result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.(i) ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
ACC.7 ¬ [m].0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RRC [m]
Rotate data memory right through carry
Description
The contents of the specified data memory and the carry flag are together rotated 1 bit
right. Bit 0 replaces the carry bit; the original carry flag is rotated into the bit 7 position.
Operation
[m].i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
[m].7 ¬ C
C ¬ [m].0
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
26
March 13, 2006
HT36FA
RRCA [m]
Rotate right through carry and place result in the accumulator
Description
Data of the specified data memory and the carry flag are rotated 1 bit right. Bit 0 replaces
the carry bit and the original carry flag is rotated into the bit 7 position. The rotated result is
stored in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
ACC.7 ¬ C
C ¬ [m].0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
SBC A,[m]
Subtract data memory and carry from the accumulator
Description
The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the accumulator.
Operation
ACC ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SBCM A,[m]
Subtract data memory and carry from the accumulator
Description
The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the data memory.
Operation
[m] ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SDZ [m]
Skip if decrement data memory is 0
Description
The contents of the specified data memory are decremented by 1. If the result is 0, the next
instruction is skipped. If the result is 0, the following instruction, fetched during the current
instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if ([m]-1)=0, [m] ¬ ([m]-1)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SDZA [m]
Decrement data memory and place result in ACC, skip if 0
Description
The contents of the specified data memory are decremented by 1. If the result is 0, the next
instruction is skipped. The result is stored in the accumulator but the data memory remains
unchanged. If the result is 0, the following instruction, fetched during the current instruction
execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if ([m]-1)=0, ACC ¬ ([m]-1)
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
27
March 13, 2006
HT36FA
SET [m]
Set data memory
Description
Each bit of the specified data memory is set to 1.
Operation
[m] ¬ FFH
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SET [m]. i
Set bit of data memory
Description
Bit i of the specified data memory is set to 1.
Operation
[m].i ¬ 1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SIZ [m]
Skip if increment data memory is 0
Description
The contents of the specified data memory are incremented by 1. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a
dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with
the next instruction (1 cycle).
Operation
Skip if ([m]+1)=0, [m] ¬ ([m]+1)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SIZA [m]
Increment data memory and place result in ACC, skip if 0
Description
The contents of the specified data memory are incremented by 1. If the result is 0, the next
instruction is skipped and the result is stored in the accumulator. The data memory remains unchanged. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper
instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if ([m]+1)=0, ACC ¬ ([m]+1)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SNZ [m].i
Skip if bit i of the data memory is not 0
Description
If bit i of the specified data memory is not 0, the next instruction is skipped. If bit i of the data
memory is not 0, the following instruction, fetched during the current instruction execution,
is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if [m].i¹0
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
28
March 13, 2006
HT36FA
SUB A,[m]
Subtract data memory from the accumulator
Description
The specified data memory is subtracted from the contents of the accumulator, leaving the
result in the accumulator.
Operation
ACC ¬ ACC+[m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SUBM A,[m]
Subtract data memory from the accumulator
Description
The specified data memory is subtracted from the contents of the accumulator, leaving the
result in the data memory.
Operation
[m] ¬ ACC+[m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SUB A,x
Subtract immediate data from the accumulator
Description
The immediate data specified by the code is subtracted from the contents of the accumulator, leaving the result in the accumulator.
Operation
ACC ¬ ACC+x+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SWAP [m]
Swap nibbles within the data memory
Description
The low-order and high-order nibbles of the specified data memory (1 of the data memories) are interchanged.
Operation
[m].3~[m].0 « [m].7~[m].4
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SWAPA [m]
Swap data memory and place result in the accumulator
Description
The low-order and high-order nibbles of the specified data memory are interchanged, writing the result to the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.3~ACC.0 ¬ [m].7~[m].4
ACC.7~ACC.4 ¬ [m].3~[m].0
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
29
March 13, 2006
HT36FA
SZ [m]
Skip if data memory is 0
Description
If the contents of the specified data memory are 0, the following instruction, fetched during
the current instruction execution, is discarded and a dummy cycle is replaced to get the
proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if [m]=0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SZA [m]
Move data memory to ACC, skip if 0
Description
The contents of the specified data memory are copied to the accumulator. If the contents is
0, the following instruction, fetched during the current instruction execution, is discarded
and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed
with the next instruction (1 cycle).
Operation
Skip if [m]=0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SZ [m].i
Skip if bit i of the data memory is 0
Description
If bit i of the specified data memory is 0, the following instruction, fetched during the current
instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if [m].i=0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
TABRDC [m]
Move the ROM code (current page) to TBLH and data memory
Description
The low byte of ROM code (current page) addressed by the table pointer (TBLP) is moved
to the specified data memory and the high byte transferred to TBLH directly.
Operation
[m] ¬ ROM code (low byte)
TBLH ¬ ROM code (high byte)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
TABRDL [m]
Move the ROM code (last page) to TBLH and data memory
Description
The low byte of ROM code (last page) addressed by the table pointer (TBLP) is moved to
the data memory and the high byte transferred to TBLH directly.
Operation
[m] ¬ ROM code (low byte)
TBLH ¬ ROM code (high byte)
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
30
March 13, 2006
HT36FA
XOR A,[m]
Logical XOR accumulator with data memory
Description
Data in the accumulator and the indicated data memory perform a bitwise logical Exclusive_OR operation and the result is stored in the accumulator.
Operation
ACC ¬ ACC ²XOR² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
XORM A,[m]
Logical XOR data memory with the accumulator
Description
Data in the indicated data memory and the accumulator perform a bitwise logical Exclusive_OR operation. The result is stored in the data memory. The 0 flag is affected.
Operation
[m] ¬ ACC ²XOR² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
XOR A,x
Logical XOR immediate data to the accumulator
Description
Data in the accumulator and the specified data perform a bitwise logical Exclusive_OR operation. The result is stored in the accumulator. The 0 flag is affected.
Operation
ACC ¬ ACC ²XOR² x
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
31
March 13, 2006
HT36FA
Package Information
20-pin SOP (300mil) Outline Dimensions
1 1
2 0
A
B
1
1 0
C
C '
G
H
D
E
Symbol
Rev. 1.10
a
F
Dimensions in mil
Min.
Nom.
Max.
A
394
¾
419
B
290
¾
300
C
14
¾
20
C¢
490
¾
510
D
92
¾
104
E
¾
50
¾
F
4
¾
¾
G
32
¾
38
H
4
¾
12
a
0°
¾
10°
32
March 13, 2006
HT36FA
32-pin SOP (450mil) Outline Dimensions
3 2
1 7
A
B
1
1 6
C
C '
G
H
D
E
Symbol
Rev. 1.10
a
F
Dimensions in mil
Min.
Nom.
Max.
A
543
¾
557
B
440
¾
450
C
14
¾
20
C¢
¾
¾
817
D
100
¾
112
E
¾
50
¾
F
4
¾
¾
G
32
¾
38
H
4
¾
12
a
0°
¾
10°
33
March 13, 2006
HT36FA
Product Tape and Reel Specifications
Reel Dimensions
D
T 2
A
C
B
T 1
SOP 20W
Symbol
Description
Dimensions in mm
A
Reel Outer Diameter
B
Reel Inner Diameter
62±1.5
C
Spindle Hole Diameter
13+0.5
-0.2
D
Key Slit Width
330±1
2±0.5
T1
Space Between Flange
24.8+0.3
-0.2
T2
Reel Thickness
30.2±0.2
SOP 32W
Symbol
Description
Dimensions in mm
A
Reel Outer Diameter
330±1
B
Reel Inner Diameter
100±0.1
C
Spindle Hole Diameter
13+0.5
-0.2
D
Key Slit Width
2±0.5
T1
Space Between Flange
32.8+0.3
-0.2
T2
Reel Thickness
38.2+0.2
Rev. 1.10
34
March 13, 2006
HT36FA
Carrier Tape Dimensions
P 0
D
P 1
t
E
F
W
C
D 1
B 0
P
K 0
A 0
SOP 20W
Symbol
Description
Dimensions in mm
W
Carrier Tape Width
24+0.3
-0.1
P
Cavity Pitch
12±0.1
E
Perforation Position
1.75±0.1
F
Cavity to Perforation (Width Direction)
11.5±0.1
D
Perforation Diameter
1.5+0.1
D1
Cavity Hole Diameter
1.5+0.25
P0
Perforation Pitch
4±0.1
P1
Cavity to Perforation (Length Direction)
2±0.1
A0
Cavity Length
10.8±0.1
B0
Cavity Width
13.3±0.1
K0
Cavity Depth
3.2±0.1
t
Carrier Tape Thickness
0.3±0.05
C
Cover Tape Width
Rev. 1.10
21.3
35
March 13, 2006
HT36FA
P 0
D
P 1
t
E
F
W
D 1
C
B 0
K 1
P
K 2
A 0
SOP 32W
Symbol
Description
Dimensions in mm
W
Carrier Tape Width
32+0.3
-0.1
P
Cavity Pitch
16±0.1
E
Perforation Position
1.75±0.1
F
Cavity to Perforation (Width Direction)
14.2±0.1
D
Perforation Diameter
1.55+0.1
D1
Cavity Hole Diameter
2+0.25
P0
Perforation Pitch
4±0.1
P1
Cavity to Perforation (Length Direction)
2±0.1
A0
Cavity Length
14.7±0.1
B0
Cavity Width
20.9±0.1
K1
Cavity Depth
3±0.1
K2
Cavity Depth
3.4±0.1
t
Carrier Tape Thickness
C
Cover Tape Width
Rev. 1.10
0.35±0.05
25.5
36
March 13, 2006
HT36FA
Holtek Semiconductor Inc. (Headquarters)
No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan
Tel: 886-3-563-1999
Fax: 886-3-563-1189
http://www.holtek.com.tw
Holtek Semiconductor Inc. (Taipei Sales Office)
4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan
Tel: 886-2-2655-7070
Fax: 886-2-2655-7373
Fax: 886-2-2655-7383 (International sales hotline)
Holtek Semiconductor Inc. (Shanghai Sales Office)
7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China 200233
Tel: 021-6485-5560
Fax: 021-6485-0313
http://www.holtek.com.cn
Holtek Semiconductor Inc. (Shenzhen Sales Office)
43F, SEG Plaza, Shen Nan Zhong Road, Shenzhen, China 518031
Tel: 0755-8346-5589
Fax: 0755-8346-5590
ISDN: 0755-8346-5591
Holtek Semiconductor Inc. (Beijing Sales Office)
Suite 1721, Jinyu Tower, A129 West Xuan Wu Men Street, Xicheng District, Beijing, China 100031
Tel: 010-6641-0030, 6641-7751, 6641-7752
Fax: 010-6641-0125
Holmate Semiconductor, Inc. (North America Sales Office)
46712 Fremont Blvd., Fremont, CA 94538
Tel: 510-252-9880
Fax: 510-252-9885
http://www.holmate.com
Copyright Ó 2006 by HOLTEK SEMICONDUCTOR INC.
The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used
solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable
without further modification, nor recommends the use of its products for application that may present a risk to human life
due to malfunction or otherwise. Holtek¢s products are not authorized for use as critical components in life support devices
or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information,
please visit our web site at http://www.holtek.com.tw.
Rev. 1.10
37
March 13, 2006