ETC STP16CP596

STP16CP596
Table 2: Typical Current Accuracy
Output Voltage
Output Current
Between Bits
Between ICs
≥ 0.1V
3 mA/VCC = 5V
5 mA/VCC = 5V
± 3%
± 6%
± 2%
± 6%
10 mA/VCC = 5V
20 mA/VCC = 5V
± 2%
± 6%
± 1%
± 6%
40 mA/VCC = 5V
50 mA/VCC = 5V
± 1%
± 6%
± 1%
± 6%
≥ 0.15V
≥ 0.25V
≥ 0.5V
≥ 1.2V
≥ 1.4V
Figure 1: Pin Connection (Note 1)
Note 1: The exposed Pad is electrically not connected.
Table 3: Pin Description
PIN N°
Symbol
1
2
3
4
5-20
21
22
23
24
GND
SDI
CLK
/LE
OUT 0-15
/OE
SDO
R-EXT
VDD
2/18
Name and Function
Ground Terminal
Serial data input terminal
Clock input terminal
Latch input terminal
Output terminal
Input terminal of output enable (active low)
Serial data out terminal
Input terminal of an external resistor for constant current programing
Supply voltage terminal
STP16CP596
Table 4: Absolute Maximum Ratings
Symbol
Parameter
Value
Unit
V
VDD
Supply Voltage
0 to 7
VO
Output Voltage
-0.5 to 16
V
IO
Output Current
50
mA
VI
Input Voltage
IGND
GND Terminal Current
-0.4 to VDD+0.4
V
800
mA
fCLK
Clock Frequency
25
MHz
TOPR
Operating Temperature Range
-40 to +125
°C
TSTG
Storage Temperature Range
-65 to +150
°C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Under these conditions, functional operation
is not implied.
Table 5: Thermal Data
Symbol
Parameter
DIP-24
SO-24
TSSOP24
TSSOP24 (*)
(exposed pad)
Unit
60
75
85
37.5
°C/W
Rthj-amb Thermal Resistance Junction-ambient
(*) The exposed pad should be soldered directly to the PCB to realize the thermal benefits.
Table 6: Recommended Operating Conditions
Symbol
Parameter
VDD
Supply Voltage
VO
Output Voltage
Test Conditions
3.0
IO
Output Current
OUTn
IOH
Output Current
SERIAL-OUT
SERIAL-OUT
IOL
Output Current
VIH
Input Voltage
VIL
Input Voltage
Min.
VDD = 3.0 to 3.6V
3
Typ.
Max.
Unit
5.5
V
16.0
V
50
mA
+1
mA
-1
mA
0.7VDD
VDD+0.3
V
-0.3
0.3VDD
/LE Pulse Width
twCLK
CLK Pulse Width
20
ns
twEN
/OE Pulse Width
400
ns
tSETUP(D) Setup Time for DATA
tHOLD(D)
Hold Time for DATA
tREM(L)
Removal Time for LATCH
fCLK
Clock Frequency
20
V
twLAT
ns
20
ns
15
ns
15
Cascade Operation
ns
25
MHz
3/18
STP16CP596
Table 7: Electrical Characteristics (VDD=3.3V to 5V, T = 25°C, unless otherwise specified.)
Symbol
Max.
Unit
VIH
Input Voltage High Level
Parameter
Test Conditions
0.7VDD
VDD
V
VIL
Input Voltage Low Level
GND
0.3VDD
V
IOH
Output Leakage Current
VOL
Output Voltage (Serial-OUT) IOL = 1mA
VOH
Output Voltage (Serial-OUT) IOH = -1mA
IOL1A
Output Current
IOL2A
∆IOL1A
∆IOL2A
IOL1B
Output Current Error
between bit (All Output ON)
∆IOL2B
RSIN(up)
Typ.
10
µA
0.4
V
3
3.15
mA
VOH = 16 V
VDD-0.4V
VO = ≥0.2V, REXT=6.2KΩ, VDD=3.3V
2.85
VO = ≥0.5V, REXT=1KΩ, VDD = 3.3V
19.6
VO = ≥0.2V, REXT=6.2KΩ, VDD=3.3V
VO = ≥0.5V, REXT=1KΩ, VDD = 3.3V
Output Current
VO = ≥0.2V, REXT=6.2KΩ, VDD=5V
VO = ≥0.5V, REXT=1KΩ, VDD = 5V
Output Current Error
between bit (All Output ON)
VO = ≥0.2V, REXT=6.2KΩ, VDD=5V
VO = ≥0.5V, REXT=1KΩ, VDD = 5V
IOL2B
∆IOL1B
Min.
Pull-up Resistor
RSIN(down) Pull-down Resistor
2.9
19.6
V
20
20.4
mA
±4
±6
%
±2
±3
%
3
3.1
mA
20
20.4
mA
±2
± 3.5
%
±1
±2
%
150
300
600
KΩ
100
200
400
IDD(OFF1) Supply Current (OFF)
REXT = OPEN OUT 0 to 15 = OFF
0.3
IDD(OFF2)
REXT = 6.2KΩ OUT 0 to 15 = OFF
1
IDD(OFF3)
REXT = 1KΩ
3
IDD(ON1)
Supply Current (ON)
IDD(ON2)
OUT 0 to 15 = OFF
REXT = 6.2KΩ OUT 0 to 15 = ON
1
REXT = 1KΩ
3
OUT 0 to 15 = ON
KΩ
mA
Table 8: Switching Characteristics (VDD=3V, T = 25°C, unless otherwise specified.)
Symbol
Typ.
Max.
Unit
250
280
ns
220
250
ns
200
250
ns
25
50
ns
25
50
ns
25
50
ns
50
70
ns
25
50
ns
tON
VDD = 3 V
Propagation Delay Time,
VIH = VDD
CLK-OUTn, /LE = H, /OE = L
VIL = GND
CL = 13pF
Propagation Delay Time,
VL = 3 V
IO = 40mA
/LE-OUTn, /OE = L
Propagation Delay Time,
REXT = 470 Ω
RL = 65 Ω
/OE-OUTn, /LE = H
Propagation Delay Time,
CLK-SDO
Propagation Delay Time,
CLK-OUTn, /LE = H, /OE = L
Propagation Delay Time,
/LE-OUTn, /OE = L
Propagation Delay Time,
/OE-OUTn, /LE = H
Propagation Delay Time,
CLK-SDO
Output Rise Time
10 ~ 90% of voltage waveform
260
400
ns
tOFF
Output Fall Time
50
80
ns
tPLH1
tPLH2
tPLH3
tPLH
tPHL1
tPHL2
tPHL3
tPHL
4/18
Parameter
Test Conditions
90 ~ 10% of voltage waveform
Min.
STP16CP596
EQUIVALENT CIRCUIT OF INPUTS AND OUTPUTS
Figure 2: /OE Terminal
Figure 3: /LE Terminal
Figure 4: CLK, SDI Terminal
5/18
STP16CP596
Figure 5: SDO Terminal
Figure 6: Block Diagram
6/18
STP16CP596
Table 9: Truth Table
CLOCK
/LE
/OE
SERIAL-IN
OUT0 .................. OUT7 .................. OUT15
SDO
H
L
Dn
Dn ..... Dn - 7 ..... Dn -15
Dn - 15
L
L
Dn + 1
No Change
Dn - 14
H
L
Dn + 2
Dn - 2 ..... Dn - 5 ..... Dn -13
Dn - 13
X
L
Dn + 3
Dn - 2 ..... Dn - 5 ..... Dn -13
Dn - 13
X
L
Dn + 3
OFF
Dn - 13
Note 1: OUT0 to OUT15 = ON when Dn = H; OUT0 to OUT15 = OFF when Dn = L.
Figure 7: Timing Diagram
Note: The latches circuit holds data when the LE terminal is Low.
When LE terminal is at High level, latch circuit doesn’t hold the data it passes from the input to the output.
When OE terminal is at Low level, output terminals OUT0 to OUT15 respond to the data, either ON or OFF.
When OE terminal is at High level, it switches off all the data on the output terminal.
7/18
STP16CP596
Figure 8: Clock, Serial-in, Serial-out
Figure 9: Clock, Serial-in, Latch, Enable, Outputs
8/18
STP16CP596
Figure 10: Outputs
TEST CIRCUIT
Figure 11: DC Characteristic
Figure 12: AC Characteristic
9/18
STP16CP596
Figure 13: Output Current-R EXT Resistor
Figure 15: Output Current vs Dropout Voltage
Figure 14: Power Dissipation vs Temperature
Package
Figure 16: Output Current vs ±∆IOL(%)
10/18
STP16CP596
Plastic DIP-24 (0.25) MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
MAX.
A
MIN.
TYP.
MAX.
4.32
A1
0.170
0.38
0.015
A2
3.3
0.130
B
0.41
0.46
0.51
0.016
0.018
0.020
B1
1.40
1.52
1.65
0.055
0.060
0.065
c
0.20
0.25
0.30
0.008
0.010
0.012
D
31.62
31.75
31.88
1.245
1.250
1.255
E
7.62
8.26
0.300
E1
6.35
6.86
0.250
6.60
0.325
0.260
e
2.54
0.100
E1
7.62
0.300
0.270
L
3.18
3.43
0.125
0.135
M
0˚
15˚
0˚
15˚
E
A
L
A2
A1
E1
Stand-off
B
B1
e
e1
c
D
24
13
.015
0,38
Gage Plane
1
12
M
0034965/D
11/18
STP16CP596
SO-24 MECHANICAL DATA
DIM.
mm.
MIN.
TYP
inch
MAX.
MIN.
TYP.
MAX.
A
2.35
2.65
0.093
0.104
A1
0.1
0.30
0.004
0.012
B
0.33
0.51
0.013
0.020
C
0.23
0.32
0.009
0.013
D
15.20
15.60
0.598
0.614
E
7.4
7.6
0.291
0.299
e
1.27
0.050
H
10.00
10.65
0.394
0.419
h
0.25
0.75
0.010
0.030
L
0.4
1.27
0.016
0.050
k
0°
8°
0°
8°
ddd
0.100
0.004
0070769C
12/18
STP16CP596
TSSOP24 EXPOSED PAD MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
MAX.
A
1.2
A1
0.15
A2
0.8
b
TYP.
MAX.
0.047
0.004
0.006
0.039
0.041
1.05
0.031
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.0089
D
7.7
7.9
0.303
D1
2.7
E
6.2
6.4
6.6
E1
4.3
4.4
4.5
E2
1.5
e
1
MIN.
7.8
0.307
0.311
0.244
0.252
0.260
0.169
0.173
0.177
0.106
0.059
0.65
K
0°
L
0.45
0.60
0.0256
8°
0°
0.75
0.018
8°
0.024
0.030
7100778C
13/18
STP16CP596
TSSOP24 MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
MAX.
A
MIN.
TYP.
MAX.
1.1
A1
0.05
0.15
A2
0.043
0.002
0.006
0.9
0.035
b
0.19
0.30
0.0075
0.0118
c
0.09
0.20
0.0035
0.0079
D
7.7
7.9
0.303
0.311
E
4.3
4.5
0.169
0.177
e
0.65 BSC
0.0256 BSC
H
6.25
6.5
0.246
0.256
K
0°
8°
0°
8°
L
0.50
0.70
0.020
0.028
A
A2
A1
b
K
e
L
H
c
D
E
PIN 1 IDENTIFICATION
1
7047476B
14/18
STP16CP596
Tape & Reel SO-24 MECHANICAL DATA
mm.
inch
DIM.
MIN.
A
TYP
MAX.
MIN.
330
MAX.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
13.2
TYP.
0.504
30.4
0.519
1.197
Ao
10.8
11.0
0.425
0.433
Bo
15.7
15.9
0.618
0.626
Ko
2.9
3.1
0.114
0.122
Po
3.9
4.1
0.153
0.161
P
11.9
12.1
0.468
0.476
15/18
STP16CP596
Tape & Reel TSSOP24 MECHANICAL DATA
mm.
inch
DIM.
MIN.
A
MAX.
MIN.
330
13.2
TYP.
MAX.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
16/18
TYP
0.504
22.4
0.519
0.882
Ao
6.8
7
0.268
0.276
Bo
8.2
8.4
0.323
0.331
Ko
1.7
1.9
0.067
0.075
Po
3.9
4.1
0.153
0.161
P
11.9
12.1
0.468
0.476
STP16CP596
Table 10: Revision History
Date
Revision
08-Apr-2005
02-May-2005
25-Jul-2005
1
2
3
Description of Changes
First Release.
Typing Error on the description features.
Add note on Fig. 1 and Table 5.
17/18
STP16CP596
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
All other names are the property of their respective owners
© 2005 STMicroelectronics - All Rights Reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
18/18
WWW.ALLDATASHEET.COM
Copyright © Each Manufacturing Company.
All Datasheets cannot be modified without permission.
This datasheet has been download from :
www.AllDataSheet.com
100% Free DataSheet Search Site.
Free Download.
No Register.
Fast Search System.
www.AllDataSheet.com