3.5x2.8mm SURFACE MOUNT LED LAMP AAA3528SURKCGKC HYPER RED GREEN Features Description BOTH CHIPS CAN BE CONTROLLED SEPARATELY. SUITABLE FOR ALL SMT ASSEMBLY AND The Hyper Red source color devices are made with DH InGaAlP on GaAs substrate Light Emitting Diode. SOLDER PROCESS. The Green source color devices are made with InGaAlP AVAILABLE ON TAPE AND REEL. on GaAs substrate Light Emitting Diode. PACKAGE: 1500PCS / REEL. RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Specifications are subjected to change without notice. SPEC NO: DSAB1049 REV NO: V.7 DATE: APR/05/2005 PAGE: 1 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1201000707 Selection Guide Part No. Dice Iv (mcd) @ 20mA Lens Type HYPER RED (InGaAlP) AAA3528SURKCGKC Viewing Angle Typ. 70 200 18 80 Units Test Conditions WATER CLEAR GREEN (InGaAIP) 2θ θ1/2 Min. 120° Note: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. Max. λpeak Peak Wavelength Hyper Red Green 650 574 nm IF=20mA λD Dominant Wavelength Hyper Red Green 635 570 nm IF=20mA ∆λ1/2 Spectral Line Half-width Hyper Red Green 28 20 nm IF=20mA C Capacitance Hyper Red Green 35 15 pF VF=0V;f=1MHz VF Forward Voltage Hyper Red Green 1.95 2.1 2.5 2.5 V IF=20mA IR Reverse Current All 10 uA VR= 5V Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Green Units Power dissipation 75 75 mW DC Forward Current 30 30 mA Peak Forward Current [1] 185 150 mA Reverse Voltage V 5 Operating / Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAB1049 REV NO: V.7 DATE: APR/05/2005 PAGE: 2 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1201000707 AAA3528SURKCGKC Hyper Red SPEC NO: DSAB1049 REV NO: V.7 DATE: APR/05/2005 PAGE: 3 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1201000707 Green SPEC NO: DSAB1049 REV NO: V.7 DATE: APR/05/2005 PAGE: 4 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1201000707 AAA3528SURKCGKC Recommended Soldering Pattern (Units : mm) Tape Specifications (Units : mm) Remarks: If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. SPEC NO: DSAB1049 REV NO: V.7 DATE: APR/05/2005 PAGE: 5 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1201000707