5.0mm x 6.0mm BI-COLOR SURFACE MOUNT LED LAMP ATTENTION AAA5060SUREVGEC HYPER RED / GREEN OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Description CHIPS CAN BE CONTROLLED SEPARATELY. The Hyper Red source color devices are made with DH SUITABLE FOR ALL SMT ASSEMBLY AND InGaAlP on GaAs substrate Light Emitting Diode. SOLDER PROCESS. The Green source color devices are made with InGaN AVAILABLE ON TAPE AND REEL. on SiC Light Emitting Diode. PACKAGE: 500PCS / REEL. Static electricity and surge damage the LEDS. RoHS COMPLIANT. It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs. All devices, equipment and machinery must be electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Specifications are subject to change without notice. SPEC NO: DSAD0905 REV NO: V.5 DATE: MAR/14/005 PAGE: 1 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1201000783 Selection Guide Part No. Dice Iv (mcd) @50mA*30 mA Lens Type Min. Typ. 380 700 *280 *600 HYPER RED (InGaAlP) Viewing Angle 2 θ 1/2 100° WATER CLEAR AAA5060SUREVGEC GREEN (InGaN) Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2. * Luminous intensity with asterisk is measured at 30mA. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. Units Test Conditions 640 518 Max. nm IF=20mA λpeak Peak Wavelength Hyper Red Green λD Dominant Wavelength Hyper Red Green 630 525 nm IF=20mA ∆λ1/2 Spectral Line Half-width Hyper Red Green 25 36 nm IF=20mA C Capacitance Hyper Red Green 45 50 pF VF=0V;f=1MHz VF Forward Voltage Hyper Red Green 1.9 3.5 2.5 4.5 V IF=20mA IR Reverse Current All 10 uA VR = 5V Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Green Units Power dissipation 125 135 mW DC Forward Current 50 30 mA Peak Forward Current [1] 200 150 mA 5 5 V Reverse Voltage Operating / Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD0905 REV NO: V.5 DATE: MAR/14/005 PAGE: 2 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1201000783 AAA5060SUREVGEC Hyper Red SPEC NO: DSAD0905 REV NO: V.5 DATE: MAR/14/005 PAGE: 3 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1201000783 Green SPEC NO: DSAD0905 REV NO: V.5 DATE: MAR/14/005 PAGE: 4 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1201000783 AAA5060SUREVGEC Recommended Soldering Pattern (Units : mm) Tape Specifications (Units : mm) If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. SPEC NO: DSAD0905 REV NO: V.5 DATE: MAR/14/005 PAGE: 5 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1201000783