AC Current transducer AP-B10 IPN = 10 .. 400 A Split core transducer for the electronic measurement AC waveforms current, with galvanic isolation between the primary (High power) and the secondary circuits (Electronic circuit). Switch selectable ranges and RMS 0-5V and 0-10V switch selectable voltage output. Electrical data Primary Nominal Current I PN (A.t.RMS) 10,25,50 50,75,100 100,150,200 200,300,400 RL VC IC Analogue Output Signal V OUT (V) 0-5V 0-5V 0-5V 0-5V or or or or 0-10V 0-10V 0-10V 0-10V Load resistance Supply voltage Current Consumption Limitation of voltage output (0-10V) Limitation of voltage output (0-5V) Overloaded input current AP AP AP AP Type Features 50 B10 100 B10 200 B10 400 B10 • RMS output • Split core type • 5V & 10V switch selectable voltage ≥ 10 kΩ +24 ±5% V DC < 30 mA 14 V 7 V no limitation X L VOE VOT TCε G tr f Accuracy @ IPN, TA = 25°C (without offset) Linearity (0 .. ± IPN) Electrical offset voltage, TA = 25°C Thermal drift of VOE Thermal drift of the gain (% of reading) Response time @ 90% of IP Frequency bandwidth (±1%) < ±1 % of IPN < ±0.5 % of IPN < ±0.5 % of IPN ±1 mV/K ±0.1 %/K < 150 ms 30 .. 2000 Hz General data TA TS m dCp dCl CTI Ambient operating temperature Ambient storage temperature Mass Protection type Creepage distance Clearance distance Comparative tracking index (Group I) UL94 classification • Eliminates insertion loss • Switch selectable ranges Advantages Accuracy-Dynamic performance data ε output • DIN mounting & Panel mounting -20 .. +60 °C -20 .. +85 °C 90 g IP20 5.5 mm 5.5 mm 600 V V0 • Large aperture for cable up to Ø18mm • High isolation between primary and secondary circuits • Easy to mount Applications • Automation systems Analog current reading for remote monitoring (e.g. motor) and software alarms. • Panelmeters Simple connection displays power consumption. Insulation category Vb Vd Ve Vw Rated Voltage 300 with IEC 61010-1 standards and following conditions : - Single insulation - Over voltage category CAT III - Pollution degree PD2 - None uniform field R.m.s. voltage for AC insulation test, 50Hz, 1mn 5 R.m.s. voltage for partial discharge extinction @ 10pC 1.5 Peak impulse withstand voltage 1.2/50µs 6.1 If insulated cable is used for the primary circuit, the voltage category could be improved with the following table : Cable insulation (primary) Category HAR 05 600V CAT III HAR 07 1000V CAT III Notes : Installation and maintenance should be done with power supply disconnected. V kV kV kV 041029/3 The operator must have accrediation to install this material. The users must take care of all protection gurantee against electrical shock. . LEM Components www.lem.com Dimensions AP(R)-B10 Output Vo ltage Selection Switch (unit : mm, 1mm = 0.0394 inch) Front Vie w Left View 55 16.40 DIN size35.50 69 14.80 Rang e Selection Switch 4.7 0 20 40(distance between screws) 21 33.50 37 Axis of ape rture 25 18 .50 67 Plug-in connector included : XW4B-03C1-H1 (OMRON) 18.50 Bottom View Mechanical characteristics • General tolerance • Primary aperture ±1 mm ∅ 18.5 mm • Panel mounting • Distance between holes 2 holes ∅ 4.0 mm 40.0 mm For panel mounting, replace M4 screws by new one (not supplied) with appropriate length to panel´s thickness. Connections • Wires up to 2 mm ∅ 0-5, 10V Selectable GND RL OUTPUT +24VDC AP/APR +24VDC Is OUT Output Connector 3(-) 2(out)1(+) Output Switch Ip GND Range Switch Front LEM reserves the right to carry out modifications on its transducers, in order to improve them, without previous notice.