Current Transducer LA 100-TP IPN = 100 A For the electronic measurement of currents : DC, AC, pulsed..., with a galvanic isolation between the primary circuit (high power) and the secondary circuit (electronic circuit). 16045 Electrical data IPN IP RM Primary nominal r.m.s. current Primary current, measuring range Measuring resistance @ with ± 12 V with ± 15 V ISN KN VC IC Vd Vb 100 0 .. ± 150 TA = 70°C TA = 85°C RM min RM max RM min RM max @ ± 100 A max @ ± 120 A max @ ± 100 A max @ ± 150 A max 0 0 0 0 50 22 110 33 Secondary nominal r.m.s. current Conversion ratio Supply voltage (± 5 %) Current consumption R.m.s. voltage for AC isolation test, 50 Hz, 1 mn R.m.s. rated voltage 0 0 20 20 42 14 102 25 A A ε Accuracy @ IPN , TA = 25°C @ ± 15 V (± 5 %) @ ± 12 .. 15 V (± 5 %) Ω Ω Ω Ω 50 mA 1 : 2000 ± 12 .. 15 V 10 (@ ± 15 V) + IS mA 2.5 kV 600 V Linearity L ± 0.45 ± 0.70 < 0.15 IO IOM IOT Offset current @ IP = 0, TA = 25°C Residual current 1) @ IP = 0, after an overload of 3 x IPN Thermal drift of IO - 25°C .. + 85°C - 40°C .. - 25°C Max ± 0.10 ± 0.15 ± 0.05 ± 0.25 ± 0.10 ± 0.50 t ra tr di/dt f Reaction time @ 10 % of IP max Response time 2) @ 90 % of IP max di/dt accurately followed Frequency bandwidth (- 1 dB) < 500 <1 > 200 DC .. 200 % % % mA mA mA mA ns µs A/µs kHz TA TS RS Ambient operating temperature Ambient storage temperature Secondary coil resistance @ m Mass Standards 1) 2) 3) according to UL 94-V0. Advantages • • • • • • • Excellent accuracy Very good linearity Low temperature drift Optimized response time Wide frequency bandwidth No insertion losses High immunity to external interference • Current overload capability. • AC variable speed drives and servo motor drives • Static converters for DC motor drives • Battery supplied applications • Uninterruptible Power Supplies (UPS) • Switched Mode Power Supplies (SMPS) • Power supplies for welding General data Notes : • Printed circuit board mounting • Insulated plastic case recognized Applications Typ 3) • Closed loop (compensated) current transducer using the Hall effect Accuracy - Dynamic performance data X Features TA = 70°C TA = 85°C - 40 .. + 85 - 50 .. + 95 120 128 24 EN 50178 °C °C Ω Ω g applications. The result of the coercive field of the magnetic circuit With a di/dt of 100 A/µs A list of corresponding tests is available 060221/7 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without previous notice. LEM page 1/2 w w w .lem.com Dimensions LA 100-TP (in mm. 1 mm = 0.0394 inch) Bottom view Left view Secondary terminals Terminal Terminal Terminal + : supply voltage + 12 .. 15 V - : supply voltage - 12 .. 15 V M : measure Connection Standard 00 or N° SP.. Year Week Front view Mechanical characteristics • General tolerance • Fastening & connection of primary Recommended PCB hole • Fastening & connection of secondary Recommended PCB hole Remarks ± 0.2 mm bus bar 6.4 x 1.6 mm 3.8 mm 3 pins 0.6 x 0.7 mm 0.9 mm • IS is positive when IP flows in the direction of the arrow. • Temperature of the primary conductor should not exceed 100°C. • This is a standard model. For different versions (supply voltages, turns ratios, unidirectional measurements...), please contact us. 060221/7 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without previous notice. LEM page 2/2 w w w .lem.com