LM82 Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface General Description The LM82 is a digital temperature sensor with a 2 wire serial interface that senses the voltage and thus the temperature of a remote diode using a Delta-Sigma analog-to-digital converter with a digital over-temperature detector. The LM82 accurately senses its own temperature as well as the temperature of external devices, such as Pentium II ® Processors or diode connected 2N3904s. The temperature of any ASIC can be detected using the LM82 as long as a dedicated diode (semiconductor junction) is available on the die. Using the SMBus interface a host can access the LM82’s registers at any time. Activation of a T_CRIT_A output occurs when any temperature is greater than a programmable comparator limit, T_CRIT. Activation of an INT output occurs when any temperature is greater than its corresponding programmable comparator HIGH limit. The host can program as well as read back the state of the T_CRIT register and the 2 T_HIGH registers. Three state logic inputs allow two pins (ADD0, ADD1) to select up to 9 SMBus address locations for the LM82. The sensor powers up with default thresholds of 127˚C for T_CRIT and all T_HIGHs. The LM82 is pin for pin and register compatible with the LM84, Maxim MAX1617 and Analog Devices ADM1021. Features n Accurately senses die temperature of remote ICs, or diode junctions n On-board local temperature sensing n SMBus and I2C compatible interface, supports SMBus 1.1 TIMEOUT n Two interrupt outputs: INT and T_CRIT_A n Register readback capability n 7 bit plus sign temperature data format, 1 ˚C resolution n 2 address select pins allow connection of 9 LM82s on a single bus Key Specifications j Supply Voltage 3.0V to 3.6V j Supply Current 0.8mA (max) j Local Temp Accuracy (includes quantization error) 0˚C to +85˚C ± 3.0˚C (max) j Remote Diode Temp Accuracy (includes quantization error) ± 3˚C (max) ± 4˚C (max) +25˚C to +100˚C 0˚C to +125˚C Applications n n n n n System Thermal Management Computers Electronic Test Equipment Office Electronics HVAC Simplified Block Diagram DS101297-1 SMBus™ is a trademark of the Intel Corporation. Pentium II ® is a registered trademark of the Intel Corporation. I2C ® is a registered trademark of the Philips Corporation. © 2000 National Semiconductor Corporation DS101297 www.national.com LM82 Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface January 2000 LM82 Connection Diagram Ordering Information QSOP-16 Order Number NS Package Number Transport Media LM82CIMQA MQA16A (QSOP-16) 95 Units in Rail LM82CIMQAX MQA16A (QSOP-16) 2500 Units on Tape and Reel DS101297-2 TOP VIEW Typical Application DS101297-3 www.national.com 2 LM82 Pin Description Label Pin # NC 1, 5 VCC 2 Function Typical Connection floating, unconnected Left floating. PC board traces may be routed through the pads for these pins. No restrictions applied. Positive Supply Voltage Input DC Voltage from 3.0 V to 3.6 V Diode Current Source To Diode Anode. Connected to remote discrete diode junction or to the diode junction on a remote IC whose die temperature is being sensed. When not used they should be left floating. D+ 3 D− 4 Diode Return Current Sink To Diode Cathode. Must float when not used. ADD0–ADD1 10, 6 User-Set SMBus (I2C) Address Inputs Ground (Low, “0”), VCC (High, “1”) or open (“TRI-LEVEL”) GND 7, 8 Power Supply Ground Ground Manufacturing test pins. Left floating. PC board traces may be routed through the pads for these pins, although the components that drive these traces should share the same supply as the LM82 so that the Absolute Maximum Rating, Voltage at Any Pin, is not violated. NC 9, 13, 15 INT 11 Interrupt Output, open-drain Pull Up Resistor, Controller Interrupt or Alert Line From and to Controller, Pull-Up Resistor SMBData 12 SMBus (I2C) Serial Bi-Directional Data Line, open-drain output SMBCLK 14 SMBus (I2C) Clock Input From Controller, Pull-Up Resistor 16 Critical Temperature Alarm, open-drain output Pull Up Resistor, Controller Interrupt Line or System Shutdown T_CRIT_A 3 www.national.com LM82 Absolute Maximum Ratings (Note 1) Supply Voltage Voltage at SMBData, SMBCLK, T_CRIT_A & INT pins Voltage at Other Pins QSOP Package (Note 3) Vapor Phase (60 seconds) Infrared (15 seconds) ESD Susceptibility (Note 4) Human Body Model Machine Model −0.3 V to 6.0 V −0.5V to 6V −0.3 V to (VCC + 0.3 V) ± 1 mA D− Input Current Input Current at All Other Pins (Note 2) 5 mA Package Input Current (Note 2) 20 mA SMBData, T_CRIT_A, INT Output Sink Current 10 mA Storage Temperature −65˚C to +150˚C Soldering Information, Lead Temperature 215˚C 220˚C 2000 V 250 V Operating Ratings (Notes 1, 5) Specified Temperature Range LM82 Supply Voltage Range (VCC) TMIN to TMAX −40˚C to +125˚C +3.0V to +3.6V Temperature-to-Digital Converter Characteristics Unless otherwise noted, these specifications apply for VCC =+3.0 Vdc to 3.6 Vdc. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ =+25˚C, unless otherwise noted. Parameter Temperature Error using Local Diode ((Note 8)) Temperature Error using Remote Diode ((Note 8)) Conditions Typical Limits (Note 6) (Note 7) (Limit) ±1 ±3 ˚C (max) TA = −40 ˚C to +125˚C, VCC =+3.3V ±4 ˚C (max) TA = +60 ˚C to +100˚C, VCC =+3.3V ±3 TA = 0 ˚C to +100˚C, VCC =+3.3V ±3 ˚C (max) TA = 0 ˚C to +125˚C, VCC =+3.3V ±4 ˚C (max) TA = 0 ˚C to +85˚C, VCC =+3.3V Resolution 8 (Note 10) Quiescent Current (Note 9) SMBus (I2C) Inactive D− Source Voltage Diode Source Current ˚C 460 600 ms (max) 0.500 0.80 mA (max) 0.7 V (D+ − D−)=+ 0.65V; high level 125 60 µA (min) Low level 15 µA (max) 5 µA (min) T_CRIT_A and INT Output Saturation Voltage IOUT = 3.0 mA 0.4 Power-On Reset Threshold On VCC input, falling edge 2.3 1.8 Local and Remote T_CRIT and HIGH Default Temperature settings (Note 11) www.national.com ˚C (max) Bits 1 Conversion Time of All Temperatures Units +127 4 µA (max) V (max) V (max) V (min) ˚C DIGITAL DC CHARACTERISTICS Unless otherwise noted, these specifications apply for VCC =+3.0 to 3.6 Vdc. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ =+25˚C, unless otherwise noted. Symbol Parameter Conditions Typical Limits Units (Note 6) (Note 7) (Limit) SMBData, SMBCLK VIN(1) Logical “1” Input Voltage 2.1 V (min) VIN(0) Logical “0”Input Voltage 0.8 V (max) VIN(HYST) SMBData and SMBCLK Digital Input Hysteresis 300 mV IIN(1) Logical “1” Input Current VIN = VCC 0.005 1.5 µA (max) IIN(0) Logical “0” Input Current VIN = 0 V −0.005 1.5 µA (max) ADD0, ADD1 VIN(1) Logical “1” Input Voltage VCC 1.5 V (min) VIN(0) Logical “0”Input Voltage GND 0.6 V (max) IIN(1) Logical “1” Input Current VIN = VCC 2 µA (max) IIN(0) Logical “0” Input Current VIN = 0 V -2 µA (max) ALL DIGITAL INPUTS CIN Input Capacitance 20 pF ALL DIGITAL OUTPUTS IOH High Level Output Current VOH = VCC 100 µA (max) VOL SMBus Low Level Output Voltage IOL = 3 mA IOL = 6 mA 0.4 0.6 V (max) 5 www.national.com LM82 Logic Electrical Characteristics LM82 Logic Electrical Characteristics (Continued) SMBus DIGITAL SWITCHING CHARACTERISTICS Unless otherwise noted, these specifications apply for VCC =+3.0 Vdc to +3.6 Vdc, CL (load capacitance) on output lines = 80 pF. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = +25˚C, unless otherwise noted. The switching characteristics of the LM82 fully meet or exceed the published specifications of the SMBus or I2C bus. The following parameters are the timing relationships between SMBCLK and SMBData signals related to the LM82. They are not the I2C or SMBus bus specifications. Symbol Parameter fSMB SMBus Clock Frequency tLOW SMBus Clock Low Time Conditions Typical Limits Units (Note 6) (Note 7) (Limit) 100 10 kHz (max) kHz (min) 10 % to 10 % 1.3 25 µs (min) ms (max) 10 ms (max) 0.6 tLOWMEXT Cumulative Clock Low Extend Time tHIGH SMBus Clock High Time 90 % to 90% tR,SMB SMBus Rise Time 10% to 90% 1 tF,SMB SMBus Fall Time 90% to 10% 0.3 tOF Output Fall Time CL = 400 pF, IO = 3 mA tTIMEOUT SMBData and SMBCLK Time Low for Reset of Serial Interface (Note 12) µs (min) µs (max) ns (max) 250 ns (max) 25 40 ms (min) ms (max) t1 SMBCLK (Clock) Period 10 µs (min) t 2, tSU;DAT Data In Setup Time to SMBCLK High 100 ns (min) t 3, tHD;DAT Data Out Stable after SMBCLK Low 300 TBD ns (min) ns (max) t 4, tHD;STA SMBData Low Setup Time to SMBCLK Low 100 ns (min) t 5, tSU;STO SMBData High Delay Time after SMBCLK High (Stop Condition Setup) 100 ns (min) t 6, tSU;STA SMBus Start-Condition Setup Time 0.6 µs (min) tBUF SMBus Free Time 1.3 µs (min) SMBus Communication DS101297-4 www.national.com 6 LM82 Logic Electrical Characteristics (Continued) SMBus TIMEOUT DS101297-7 See drawing DS10129707 Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its rated operating conditions. Note 2: When the input voltage (VI) at any pin exceeds the power supplies (VI < GND or VI > VCC), the current at that pin should be limited to 5 mA. The 20 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 5 mA to four. Parasitic components and or ESD protection circuitry are shown in the figure below for the LM82’s pins. The nominal breakdown voltage of the zener D3 is 6.5 V. Care should be taken not to forward bias the parasitic diode, D1, present on pins: D+, D−, ADD1 and ADD0. Doing so by more than 50 mV may corrupt a temperature or voltage measurement. Pin Name D1 D2 D3 D4 Pin Name NC (pins 1 & 5) D1 T_CRIT_A & INT VCC x SMBData D+ x x x NC (pins 9 & 15) D− x x x ADD0, ADD1 x x x x D2 D3 D4 x x x x x SMBCLK x x NC (pin 13) x x x Note: An x indicates that the diode exists. DS101297-13 FIGURE 1. ESD Protection Input Structure Note 3: See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” or the section titled “Surface Mount” found in a current National Semiconductor Linear Data Book for other methods of soldering surface mount devices. Note 4: Human body model, 100 pF discharged through a 1.5 kΩ resistor. Machine model, 200 pF discharged directly into each pin. Note 5: Thermal resistance of the QSOP-16 package is 130˚C/W, junction-to-ambient when attached to a FR-4 printed circuit board with 1 oz. foil as shown in Figure 3 . 7 www.national.com LM82 Logic Electrical Characteristics (Continued) Note 6: Typicals are at TA = 25˚C and represent most likely parametric norm. Note 7: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level). Note 8: The Temperature Error will vary less than ± 1.0˚C for a variation in VCC of 3V to 3.6V from the nominal of 3.3V. Note 9: Quiescent current will not increase substantially with an active SMBus. Note 10: This specification is provided only to indicate how often temperature data is updated. The LM82 can be read at any time without regard to conversion state (and will yield last conversion result). Note 11: Default values set at power up. Note 12: Holding the SMBData and/or SMBCLK lines Low for a time interval greater than tTIMEOUT will cause the LM82 to reset SMBData and SMBCLK to the IDLE state of an SMBus communication (SMBCLK and SMBData set High). DS101297-5 FIGURE 2. Temperature-to-Digital Transfer Function (Non-linear scale for clarity) DS101297-24 FIGURE 3. Printed Circuit Board Used for Thermal Resistance Specifications 1.0 Functional Description This round robin sequence takes approximately 480 ms to complete. The LM82 temperature sensor incorporates a band-gap type temperature sensor using a Local or Remote diode and an 8-bit ADC (Delta-Sigma Analog-to-Digital Converter). The LM82 is compatible with the serial SMBus and I2C two wire interfaces. Digital comparators compare Local (LT) and Remote (RT) temperature readings to user-programmable setpoints (LHS, RHS, and TCS). Activation of the INT output indicates that a comparison is greater than the limit preset in a HIGH register. The T_CRIT setpoint (TCS) interacts with all the temperature readings. Activation of the T_CRIT_A output indicates that any or all of the temperature readings have exceed the T_CRIT setpoint. 1.2 INT OUTPUT and T_HIGH LIMITS Each temperature reading (LT, and RT) is associated with a T_HIGH setpoint register (LHS, RHS). At the end of a temperature reading a digital comparison determines whether that reading has exceeded its HIGH setpoint. If the temperature reading is greater than the HIGH setpoint, a bit is set in one of the Status Registers, to indicate which temperature reading, and the INT output is activated. Local and remote temperature diodes are sampled in sequence by the A/D converter. The INT output and the Status Register flags are updated at the completion of a conversion, which occurs approximately 60 ms after a temperature diode is sampled. INT is deactivated when the Status Register, containing the set bit, is read and a temperature reading is 1.1 CONVERSION SEQUENCE The LM82 converts its own temperature as well as a remote diode temperature in the following sequence: 1. Local Temperature (LT) 2. Remote Diode (RT) www.national.com 8 conversion is below the T_CRIT setpoint, as shown in Figure 6. Figure 7 shows a simplified logic diagram of the T_CRIT_A and related circuitry. (Continued) less than or equal to it’s corresponding HIGH setpoint, as shown in Figure 4. Figure 5shows a simplified logic diagram for the INT output and related circuitry. DS101297-6 * Note: Status Register Bits are reset by a read of Status Register where bit is located. FIGURE 6. T_CRIT_A Temperature Response Diagram DS101297-14 * Note: Status Register Bits are reset by a read of Status Register where bit is located. FIGURE 4. INT Temperature Response Diagram DS101297-20 FIGURE 7. T_CRIT_A output related circuitry logic diagram DS101297-21 FIGURE 5. INT output related circuitry logic diagram Located in the Configuration Register are the mask bits for each temperature reading, seeSection 2.5. When a mask bit is set, its corresponding status flag will not propagate to the T_CRIT_A output, but will still be set in the Status Registers. Configuration register bits D5 and D3, labled “Remote T_CRIT_A mask” must be set high before the T_CRIT setpoint is lowered in order for the T_CRIT_A output to function properly. Setting all four mask bits or programming the T_CRIT setpoint to 127˚C will disable the T_CRIT_A output. The INT output can be disabled by setting the INT mask bit, D7, of the configuration register. INT can be programmed to be active high or low by the state of the INT inversion bit, D1, in the configuration register. A “0” would program INT to be active low. INT is an open-drain output. 1.3 T_CRIT_A OUTPUT and T_CRIT LIMIT T_CRIT_A is activated when any temperature reading is greater than the limit preset in the critical temperature setpoint register (T_CRIT), as shown in Figure 6. The Status Registers can be read to determine which event caused the alarm. A bit in the Status Registers is set high to indicate which temperature reading exceeded the T_CRIT setpoint temperature and caused the alarm, see Section 2.3. Local and remote temperature diodes are sampled in sequence by the A/D converter. The T_CRIT_A output and the Status Register flags are updated at the completion of a conversion. T_CRIT_A and the Status Register flags are reset only after the Status Register is read and if a temperature 1.4 POWER ON RESET DEFAULT STATES LM82 always powers up to these known default states: 1. Command Register set to 00h 2. Local Temperature set to 0˚C 3. Remote Temperature set to 0˚C until the LM82 senses a diode present between the D+ and D− input pins. 4. Status Register set to 00h. 5. Configuration Register set to 00h; INT enabled and all T_CRIT setpoints enabled to activate T_CRIT_A. 9 www.national.com LM82 1.0 Functional Description LM82 1.0 Functional Description 6. (Continued) Temperature 1.5 SMBus INTERFACE The LM82 operates as a slave on the SMBus, so the SMBCLK line is an input (no clock is generated by the LM82) and the SMBData line is bi-directional. According to SMBus specifications, the LM82 has a 7-bit slave address. Bit 4 (A3) of the slave address is hard wired inside the LM82 to a 1. The remainder of the address bits are controlled by the state of the address select pins ADD1 and ADD0, and are set by connecting these pins to ground for a low, (0) , to VCC for a high, (1), or left floating (TRI-LEVEL). Therefore, the complete slave address is: A6 A5 A4 1 A2 A1 MSB Hex +125˚C 0111 1101 7Dh +25˚C 0001 1001 19h +1˚C 0000 0001 01h A0 LSB ADD0 ADD1 LM82 SMBus Slave Address A6:A0 binary 0 0 001 1000 0 TRI-LEVEL 001 1001 0 1 001 1010 TRI-LEVEL 0 010 1001 TRI-LEVEL TRI-LEVEL 010 1010 TRI-LEVEL 1 010 1011 1 0 100 1100 1 TRI-LEVEL 100 1101 1 1 100 1110 0000 0000 00h 1111 1111 FFh −25˚C 1110 0111 E7h −55˚C 1100 1001 C9h 1.8 DIODE FAULT DETECTION Before each external conversion the LM82 goes through an external diode fault detection sequence. If D+ input is shorted to VCC or floating then the temperature reading will be +127 ˚C, and the OPEN bit in the Status Register will be set. If the T_CRIT setpoint is set to less than +127 ˚C then the D+ input RTCRIT bit in the Status Register will be set which will activate the T_CRIT_A output, if enabled. If a D+ is shorted to GND or D−, its temperature reading will be 0 ˚C and its OPEN bit in the Status Register will not be set. The LM82 latches the state of the address select pins during the first read or write on the SMBus. Changing the state of the address select pins after the first read or write to any device on the SMBus will not change the slave address of the LM82. 1.6 TEMPERATURE DATA FORMAT Temperature data can be read from the Local and Remote Temperature, T_CRIT, and HIGH setpoint registers; and written to the T_CRIT and HIGH setpoint registers. Temperature data is represented by an 8-bit, two’s complement byte with an LSB (Least Significant Bit) equal to 1˚C: www.national.com 0˚C −1˚C 1.7 OPEN-DRAIN OUTPUTS The SMBData, INT and T_CRIT_A outputs are open-drain outputs and do not have internal pull-ups. A “high” level will not be observed on these pins until pull-up current is provided from some external source, typically a pull-up resistor. Choice of resistor value depends on many system factors but, in general, the pull-up resistor should be as large as possible. This will minimize any internal temperature reading errors due to internal heating of the LM82. The maximum resistance of the pull up, based on LM82 specification for High Level Output Current, to provide a 2.1V high level, is 30kΩ. Care should be taken in a noisy system because a high impedance pull-up will be more likely to couple noise into the signal line. and is selected as follows: Address Select Pin State Digital Output Binary Local and Remote T_CRIT set to 127˚C 10 LM82 1.0 Functional Description (Continued) 1.9 COMMUNICATING with the LM82 DS101297-9 1.10 SERIAL INTERFACE ERROR RECOVERY The LM82 SMBus lines will be reset to the SMBus idle state if the SMBData or SMBCLK lines are held low for 40 ms or more (tTIMEOUT). The LM82 may or may not reset the state of the serial interface logic if either of the SMBData or SMBCLK lines are held low between 25 ms and 40 ms. TIMEOUT allows a clean recovery in cases where the master may be reset while the LM82 is transmitting a low bit thus preventing possible bus lock up. Whenever the LM82 sees the start condition its serial interface will reset to the beginning of the communication, thus the LM82 will expect to see an address byte next. This simplifies recovery when the master is reset while the LM82 is transmitting a high. There are 13 data registers in the LM82, selected by the Command Register. At power-up the Command Register is set to “00”, the location for the Read Local Temperature Register. The Command Register latches the last location it was set to. Reading the Status Register resets T_CRIT_A and INT, so long as a temperature comparison does not signal a fault (see Sections 1.2 and 1.3). All other registers are predefined as read only or write only. Read and write registers with the same function contain mirrored data. A Write to the LM82 will always include the address byte and the command byte. A write to any register requires one data byte. Reading the LM82 can take place either of two ways: 1. If the location latched in the Command Register is correct (most of the time it is expected that the Command Register will point to one of the Read Temperature Registers because that will be the data most frequently read from the LM82), then the read can simply consist of an address byte, followed by retrieving the data byte. 2. If the Command Register needs to be set, then an address byte, command byte, repeat start, and another address byte will accomplish a read. The data byte has the most significant bit first. At the end of a read, the LM82 can accept either Acknowledge or No Acknowledge from the Master (No Acknowledge is typically used as a signal for the slave that the Master has read its last byte). 11 www.national.com LM82 1.0 Functional Description (Continued) 2.0 LM82 REGISTERS 2.1 COMMAND REGISTER Selects which registers will be read from or written to. Data for this register should be transmitted during the Command Byte of the SMBus write communication. P7 P6 P5 P4 0 P3 P2 P1 P0 Command Select P0-P7: Command Select Command Select Address < P7:P0 > hex Power On Default State < D7:D0 > binary Register Name Register Function < D7:D0 > decimal 00h 0000 0000 0 RLT Read Local Temperature 01h 0000 0000 0 RRT Read Remote Temperature 02h 0000 0000 0 RSR Read Status Register 03h 0000 0000 0 RC 04h 0000 0000 0 05h 0111 1111 127 Reserved RLHS 06h 07h 0111 1111 127 RRHS 0000 0000 WC 127 WRHS 0111 1111 127 0000 0000 0 WLHS Reserved Reserved for Future Use 0000 0000 0 Reserved 36h-37h 38h Reserved for Future Use 0111 1111 127 Reserved 0111 1111 127 Reserved 0111 1111 127 0111 1111 127 39h 3Ah Reserved for Future Use 3Bh-41h 42h Reserved for Future Use RTCS 43h-4Fh 50h Reserved Reserved for Future Use 0111 1111 127 Reserved 53h-59h 5Ah Reserved for Future Use 0111 1111 127 WTCS 5Ch-6Fh and F0h-FDh FEh FFh www.national.com Read T_CRIT Setpoint Reserved for Future Use 51h 52h Write Local HIGH Setpoint Reserved for Future Use 32h-34h 35h Write Local HIGH Setpoint Reserved 0Eh-2Fh 30h-31h Write Configuration Reserved 0111 1111 0Ch 0Dh Read Remote HIGH Setpoint Reserved 0Ah 0Bh Read Local HIGH Setpoint Reserved 08h 09h Read Configuration Write T_CRIT Setpoint Reserved for Future Use 0000 0001 1 RMID Read Manufacturers ID 1 RSR Read Stepping or Die Revision Code 12 LM82 1.0 Functional Description (Continued) 2.2 LOCAL and REMOTE TEMPERATURE REGISTERS (LT, and RT) (Read Only Address 00h, and 01h): D7 D6 D5 D4 D3 D2 D1 D0 MSB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 LSB D7–D0: Temperature Data. One LSB = 1˚C. Two’s complement format. 2.3 STATUS REGISTER (Read Only Address 02h): D7 D6 D5 D4 D3 D2 D1 D0 0 LHIGH 0 RHIGH 0 OPEN RCRIT LCRIT Power up default is with all bits “0” (zero). D0: LCRIT: When set to a 1 indicates an Local Critical Temperature alarm. D1: RCRIT: When set to a 1 indicates a Remote Diode Critical Temperature alarm. D2: D2OPEN: When set to 1 indicates a Remote Diode disconnect. D4: D2RHIGH: When set to 1 indicates a Remote Diode HIGH Temperature alarm. D6: LHIGH: When set to 1 indicates a Local HIGH Temperature alarm. D7, D5, and D3: These bits are always set to 0 and reserved for future use. 2.4 MANUFACTURERS ID and DIE REVISION(Stepping) REGISTERS (Read Address FEh and FFh) Default value 01h for Manufacturers ID(FEh ). 2.5 CONFIGURATION REGISTER (Read Address 03h/Write Address 09h): D7 D6 D5 D4 D3 D2 D1 D0 INT mask 0 Remote T_CRIT_A mask Remote T_CRIT_A mask Remote T_CRIT_A mask Local T_CRIT_A mask INT Inversion 0 Power up default is with all bits “0” (zero). D7: INT mask: When set to 1 INT interrupts are masked. D5: T_CRIT mask, this bit must be set to a 1 before the T_CRIT setpoint is lowered below 127 in order for T_CRIT_A pin to function properly. D4: T_CRIT mask for Remote temperature, when set to 1 a remote temperature reading that exceeds T_CRIT setpoint will not activate the T_CRIT_A pin. D3: T_CRIT mask, this bit must be set to a 1 before the T_CRIT setpoint is lowered below 127 in order for T_CRIT_A pin to function properly. D2: T_CRIT mask for Local reading, when set to 1 a Local temperature reading that exceeds T_CRIT setpoint will not activate the T_CRIT_A pin. D1: INT active state inversion. When INT Inversion is set to a 1 the active state of the INT output will be a logical high. A low would then select an active state of a logical low. D6 and D0: These bits are always set to 0 and reserved for future use. A write of 1 will return a 0 when read. 2.6 LOCAL, and REMOTE HIGH SETPOINT REGISTERS (LHS, RHS) (Read Address 05h, 07h/Write Address 0Bh, 0Dh): D7 D6 D5 D4 D3 D2 D1 D0 MSB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 LSB D7–D0: HIGH setpoint temperature data. Power up default is LHIGH = RHIGH=127˚C. 2.7 T_CRIT REGISTER (TCS) (Read Address 42h/Write Address 5Ah): D7 D6 D5 D4 D3 D2 D1 D0 MSB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 LSB D7–D0: T_CRIT setpoint temperature data. Power up default is T_CRIT = 127˚C. 13 www.national.com LM82 3.0 SMBus Timing Diagrams DS101297-10 (a) Serial Bus Write to the internal Command Register followed by a the Data Byte DS101297-11 (b) Serial Bus Write to the internal Command Register DS101297-12 (c) Serial Bus Read from a Register with the internal Command Register preset to desired value. FIGURE 8. Serial Bus Timing Diagrams www.national.com 14 LM82 4.0 Application Hints The LM82 can be applied easily in the same way as other integrated-circuit temperature sensors and its remote diode sensing capability allows it to be used in new ways as well. It can be soldered to a printed circuit board, and because the path of best thermal conductivity is between the die and the pins, its temperature will effectively be that of the printed circuit board lands and traces soldered to the LM82’s pins. This presumes that the ambient air temperature is almost the same as the surface temperature of the printed circuit board; if the air temperature is much higher or lower than the surface temperature, the actual temperature of the of the LM82 die will be at an intermediate temperature between the surface and air temperatures. Again, the primary thermal conduction path is through the leads, so the circuit board temperature will contribute to the die temperature much more strongly than will the air temperature. To measure temperature external to the LM82’s die, use a remote diode. This diode can be located on the die of a target IC, allowing measurement of the IC’s temperature, independent of the LM82’s temperature. The LM82 has been optimized to measure the remote diode of a Pentium II processor as shown in Figure 9. A discrete diode can also be used to sense the temperature of external objects or ambient air. Remember that a discrete diode’s temperature will be affected, and often dominated, by the temperature of its leads. where: • η is the non-ideality factor of the process the diode is manufactured on, • q is the electron charge, • k is the Boltzmann’s constant, • N is the current ratio, • T is the absolute temperature in ˚K. The temperature sensor then measures ∆VBE and converts to digital data. In this equation, k and q are well defined universal constants, and N is a parameter controlled by the temperature sensor. The only other parameter is η, which depends on the diode that is used for measurement. Since ∆VBE is proportional to both η and T, the variations in η cannot be distinguished from variations in temperature. Since the non-ideality factor is not controlled by the temperature sensor, it will directly add to the inaccuracy of the sensor. For the Pentium II Intel specifies a ± 1% variation in η from part to part. As an example, assume a temperature sensor has an accuracy specification of ± 3 ˚C at room temperature of 25 ˚C and the process used to manufacture the diode has a non-ideality variation of ± 1%. The resulting accuracy of the temperature sensor at room temperature will be: TACC = ± 3˚C + ( ± 1% of 298 ˚K) = ± 6 ˚C. The additional inaccuracy in the temperature measurement caused by η, can be eliminated if each temperature sensor is calibrated with the remote diode that it will be paired with. 3.2 PCB LAYOUT for MINIMIZING NOISE In a noisy environment, such as a processor mother board, layout considerations are very critical. Noise induced on traces running between the remote temperature diode sensor and the LM82 can cause temperature conversion errors. The following guidelines should be followed: 1. Place a 0.1 µF power supply bypass capacitor as close as possible to the VCCpin and the recommended 2.2 nF capacitor as close as possible to the D+ and D− pins. Make sure the traces to the 2.2nF capacitor are matched. 2. The recommended 2.2nF diode bypass capacitor actually has a range of 200pF to 3.3nF. The average temperature accuracy will not degrade. Increasing the capacitance will lower the corner frequency where differential noise error affects the temperature reading thus producing a reading that is more stable. Conversely, lowering the capacitance will increase the corner frequency where differential noise error affects the temperature reading thus producing a reading that is less stable. 3. Ideally, the LM82 should be placed within 10cm of the Processor diode pins with the traces being as straight, short and identical as possible. Trace resistance of 1Ω can cause as much as 1˚C of error. 4. Diode traces should be surrounded by a GND guard ring to either side, above and below if possible. This GND guard should not be between the D+ and D− lines. In the event that noise does couple to the diode lines it would be ideal if it is coupled common mode. That is equally to the D+ and D− lines.(See Figure 10) 5. Avoid routing diode traces in close proximity to power supply switching signals or filtering inductors. DS101297-15 Pentium or 3904 Temperature vs LM82 Temperature Reading Most silicon diodes do not lend themselves well to this application. It is recommended that a 2N3904 transistor base emitter junction be used with the collector tied to the base. A diode connected 2N3904 approximates the junction available on a Pentium microprocessor for temperature measurement. Therefore, the LM82 can sense the temperature of this diode effectively. 3.1 ACCURACY EFFECTS OF DIODE NON-IDEALITY FACTOR The technique used in today’s remote temperature sensors is to measure the change in VBE at two different operating points of a diode. For a bias current ratio of N:1, this difference is given as: 15 www.national.com LM82 4.0 Application Hints 6. (Continued) Avoid running diode traces close to or parallel to high speed digital and bus lines. Diode traces should be kept at least 2cm. apart from the high speed digital traces. 7. If it is necessary to cross high speed digital traces, the diode traces and the high speed digital traces should cross at a 90 degree angle. 8. The ideal place to connect the LM82’s GND pin is as close as possible to the Processors GND associated with the sense diode. 9. Leakage current between D+ and GND should be kept to a minimum. One nano-ampere of leakage can cause as much as 1˚C of error in the diode temperature reading. Keeping the printed circuit board as clean as possible will minimize leakage current. www.national.com DS101297-17 FIGURE 10. Ideal Diode Trace Layout Noise coupling into the digital lines greater than 300mVp-p (typical hysteresis), overshoot greater than 500mV above VCC, and undershoot less than 500mV below GND, may prevent successful SMBus communication with the LM82. SMBus no acknowledge is the most common symptom, causing unnecessary traffic on the bus. Although, the SMBus maximum frequency of communication is rather low (100kHz max) care still needs to be taken to ensure proper termination within a system with multiple parts on the bus and long printed circuit board traces. An R/C lowpass filter with a 3db corner frequency of about 40MHz has been included on the LM82’s SMBCLK input. Additional resistance can be added in series with the SMBData and SMBCLK lines to further help filter noise and ringing. Minimize noise coupling by keeping digital traces out of switching power supply areas as well as ensuring that digital lines containing high speed data communications cross at right angles to the SMBData and SMBCLK lines. 16 inches (millimeters) unless otherwise noted 16-Lead QSOP Package Order Number LM82CIMQA or LM82CIMQAX NS Package Number MQA16 LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: [email protected] www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. LM82 Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface Physical Dimensions