IXYS LAA100LS

LAA100L
Dual Single-Pole
OptoMOS® Relays
INTEGRATED CIRCUITS DIVISION
Parameter
Blocking Voltage
Load Current
On-Resistance (max)
Ratings
350
120
25
Units
VP
mArms / mADC

Description
The LAA100L is a 350V, 120mA, dual single-pole,
normally open (1-Form-A) relay. It features low, 25,
maximum on-resistance, and includes integrated
current limiting.
Features
Approvals
• 3750Vrms Input/Output Isolation
• Low Drive Power Requirements (TTL/CMOS
Compatible)
• No Moving Parts
• High Reliability
• Arc-Free With No Snubbing Circuits
• FCC Compatible
• VDE Compatible
• No EMI/RFI Generation
• Small 8-Pin DIP Package
• Machine Insertable, Wave Solderable
• Surface Mount Tape & Reel Version Available
• UL recognized: File Number E76270
• CSA Certified: File Number LR43639-10
• EN/IEC 60950-1 compliant
Ordering Information
Part #
LAA100L
LAA100PL
LAA100PLTR
LAA100LS
LAA100LSTR
Applications
Description
8 Pin DIP (50/Tube)
8-Pin Flatpack (50/Tube)
8-Pin Flatpack (1000/Reel)
8 Pin Surface Mount (50/Tube)
8 Pin Surface Mount (1,000/Reel)
Pin Configuration
• Telecommunications
• Telecom Switching
• Tip/Ring Circuits
• Modem Switching (Laptop, Notebook,
Pocket Size)
• Hook Switch
• Dial Pulsing
• Ground Start
• Ringing Injection
• Instrumentation
• Multiplexers
• Data Acquisition
• Electronic Switching
• I/O Subsystems
• Meters (Watt-Hour, Water, Gas)
• Medical Equipment—Patient/Equipment Isolation
• Security
• Aerospace
• Industrial Controls
AC/DC Configuration
+ Control - Switch #1
– Control - Switch #1
+ Control - Switch #2
– Control - Switch #2
1
8
2
7
3
6
4
5
Load - Switch #1
Load - Switch #1
Load - Switch #2
Load - Switch #2
Switching Characteristics of
Normally Open (Form A) Devices
Form-A
IF
90%
10%
ILOAD
ton
Pb
DS-LAA100L-R02
toff
e3
www.ixysic.com
1
INTEGRATED CIRCUITS DIVISION
LAA100L
Absolute Maximum Ratings @25ºC
Parameter
Blocking Voltage
Reverse Input Voltage
Input Control Current
Peak (10ms)
Input Power Dissipation 1
Total Power Dissipation 2
Isolation Voltage, Input to Output
Operational Temperature
Storage Temperature
1
Derate linearly 1.33 mW / ºC
2
Derate linearly 6.67 mW / ºC
Ratings
350
5
50
1
150
800
3750
-40 to +85
-40 to +125
Absolute Maximum Ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to
the device. Functional operation of the device at conditions
beyond those indicated in the operational sections of this
data sheet is not implied.
Units
VP
V
mA
A
mW
mW
Vrms
°C
°C
Electrical Characteristics @25ºC
Parameter
Output Characteristics
Load Current
Continuous 1
Peak
On-Resistance 2
Off-State Leakage Current
Switching Speeds
Turn-On
Turn-Off
Output Capacitance
Input Characteristics
Input Control Current to Activate
Input Control Current to Deactivate
Input Voltage Drop
Reverse Input Current
Common Characteristics
Capacitance Input to Output
1
2
Conditions
Symbol
Min
Typ
Max
Units
10ms
IL=120mA
VL=350V
IL
ILPK
RON
ILEAK
-
-
120
±350
25
1
mArms / mADC
mAP

IF = 5mA, VL = 10V
VL = 50V, f=1MHz
ton
toff
COUT
-
35
5
5
-
ms
ms
pF
IL = 120mA
IF = 5mA
VR = 5V
IF
IF
VF
IR
0.4
0.9
-
1.0
1.2
-
5
1.4
10
mA
mA
V
µA
-
CI/O
-
3
-
pF
µA
If both poles operate, the load current must be derated so that the package power dissipation value is not exceeded.
Measurement taken within 1 second of on-time.
2
www.ixysic.com
R02
INTEGRATED CIRCUITS DIVISION
LAA100L
PERFORMANCE DATA @25ºC (Unless Otherwise Noted)*
35
Typical LED Forward Voltage Drop
(N=50, IF=5mA)
Typical Turn-Off Time
(N=50, IF=5mA, IL=120mADC)
Typical Turn-On Time
(N=50, IF=5mA, IL=120mADC)
25
25
25
20
15
10
20
15
10
5
5
0
0
1.17
1.19
1.21
1.23
1.25
Device Count (N)
Device Count (N)
Device Count (N)
30
0.15
0.25
LED Forward Voltage Drop (V)
25
20
20
15
10
5
0.65
15
10
5
0
0.75
0.025
Typical IF for Switch Dropout
(N=50, IL=120mADC)
0.075
0.125
0.175
0.225
Typical On-Resistance Distribution
(N=50, IF=2mA, IL=120mADC)
35
30
Device Count (N)
25
Device Count (N)
Device Count (N)
Typical IF for Switch Operation
(N=50, IL=120mADC)
0.35 0.45 0.55
Turn-On (ms)
20
15
10
5
25
20
15
10
5
0
0
0.45
0.75
1.05 1.35 1.65
LED Current (mA)
1.95
2.25
0.45
0.75
1.05 1.35 1.65 1.95
LED Current (mA)
0
2.25
17.0
17.4
17.8 18.2 18.6 19.0
On-Resistance (:)
19.4
Typical Blocking Voltage Distribution
(N=50)
35
Device Count (N)
30
25
20
15
10
5
0
376.3 382.8 389.3 395.8 402.3 408.8 415.3
Blocking Voltage (VP)
Typical Turn-On Time
vs. LED Forward Current
(IL=120mADC)
1.6
1.4
IF=50mA
IF=30mA
IF=20mA
IF=10mA
IF=5mA
1.2
1.0
0.8
-40
-20
0
20
40
60
80
Temperature (ºC)
100
120
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
Typical Turn-Off Time
vs. LED Forward Current
(IL=120mADC)
0.35
0.30
Turn-Off Time (ms)
1.8
Turn-On Time (ms)
LED Forward Voltage Drop (V)
Typical LED Forward Voltage Drop
vs. Temperature
0.25
0.20
0.15
0.10
0.05
0
0
5
10
15
20
25
30
35
40
LED Forward Current (mA)
45
50
0
5
10 15 20 25 30 35 40
LED Forward Current (mA)
45
50
*The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application
department.
R02
www.ixysic.com
3
INTEGRATED CIRCUITS DIVISION
LAA100L
PERFORMANCE DATA @25ºC (Unless Otherwise Noted)*
Turn-On Time (ms)
40
30
20
10
0
-40
-20
0
20
40
60
Temperature (ºC)
80
100
0
20
40
60
Temperature (ºC)
80
LED Current (mA)
2.0
1.5
1.0
0
-20
0
20
40
60
Temperature (ºC)
80
100
80
IF=10mA
IF=5mA
IF=2mA
60
40
-20
0
20
40
60
Temperature (ºC)
80
-40
100
14
400
12
Leakage (nA)
100
Blocking Voltage (VP)
16
390
380
370
-2
-1
0
1
Load Voltage (V)
2
3
0
20
40
60
80
Temperature (ºC)
100
120
10
8
6
4
360
2
-150
-3
-20
Typical Leakage vs. Temperature
Measured across Pins 4 & 6
Typical Blocking Voltage
vs. Temperature
410
-100
100
120
420
-50
80
140
150
0
20
40
60
Temperature (ºC)
0
Typical Load Current vs. Load Voltage
(IF=2mA)
50
0
20
-40
100
-20
160
1.0
0
-40
Maximum Load Current vs. Temperature
1.5
0.5
IF=2mA
IF=5mA
180
2.0
0.5
Typical Turn-Off Time vs. Temperature
(IF=120mADC)
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
100
2.5
-40
Load Current (mA)
-20
Typical IF for Switch Dropout
vs. Temperature
(IL=120mADC)
3.0
2.5
LED Current (mA)
-40
Typical IF for Switch Operation
vs. Temperature
(IL=120mADC)
3.0
IF=2mA
IF=5mA
IF=10mA
IF=20mA
Load Current (mA)
On-Resistance (:)
50
Typical Turn-On Time vs. Temperature
(IL=120mADC)
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
Turn-Off Time (ms)
Typical On-Resistance vs. Temperature
(IF=2mA, IL=120mADC)
60
-40
-20
0
20
40
60
Temperature (ºC)
80
100
80
100
0
-40
-20
0
20
40
60
Temperature (ºC)
80
100
Typical Current Limiting
vs. Temperature
(IF=2mA)
350
Current (mA)
300
250
200
150
100
50
0
-40
-20
0
20
40
60
Temperature (ºC)
*The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application
department.
4
www.ixysic.com
R02
INTEGRATED CIRCUITS DIVISION
LAA100L
Manufacturing Information
Moisture Sensitivity
All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated
Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to
the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product
evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper
operation of our devices when handled according to the limitations and information in that standard as well as to any
limitations set forth in the information or standards referenced below.
Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced
product performance, reduction of operable life, and/or reduction of overall reliability.
This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according
to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033.
Device
Moisture Sensitivity Level (MSL) Rating
LAA100L / LAA100LS / LAA100PL
MSL 1
ESD Sensitivity
This product is ESD Sensitive, and should be handled according to the industry standard JESD-625.
Reflow Profile
This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020
must be observed.
Device
Maximum Temperature x Time
LAA100L / LAA100LS
250ºC for 30 seconds
LAA100PL
260ºC for 30 seconds
Board Wash
IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to
remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as
an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary
if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used.
Cleaning methods that employ ultrasonic energy should not be used.
Pb
R02
e3
www.ixysic.com
5
INTEGRATED CIRCUITS DIVISION
LAA100L
MECHANICAL DIMENSIONS
LAA100L
2.540 ± 0.127
(0.100 ± 0.005)
9.652 ± 0.381
(0.380 ± 0.015)
8-0.800 DIA.
(8-0.031 DIA.)
2.540 ± 0.127
(0.100 ± 0.005)
9.144 ± 0.508
(0.360 ± 0.020)
6.350 ± 0.127
(0.250 ± 0.005)
Pin 1
PCB Hole Pattern
7.620 ± 0.254
(0.300 ± 0.010)
6.350 ± 0.127
(0.250 ± 0.005)
0.457 ± 0.076
(0.018 ± 0.003)
3.302 ± 0.051
(0.130 ± 0.002)
7.620 ± 0.127
(0.300 ± 0.005)
7.239 TYP.
(0.285)
4.064 TYP
(0.160)
7.620 ± 0.127
(0.300 ± 0.005)
0.254 ± 0.0127
(0.010 ± 0.0005)
Dimensions
mm
(inches)
0.813 ± 0.102
(0.032 ± 0.004)
LAA100LS
9.652 ± 0.381
(0.380 ± 0.015)
2.540 ± 0.127
(0.100 ± 0.005)
6.350 ± 0.127
(0.250 ± 0.005)
Pin 1
0.635 ± 0.127
(0.025 ± 0.005)
3.302 ± 0.051
(0.130 ± 0.002)
9.525 ± 0.254
(0.375 ± 0.010)
0.457 ± 0.076
(0.018 ± 0.003)
PCB Land Pattern
2.54
(0.10)
8.90
(0.3503)
1.65
(0.0649)
7.620 ± 0.254
(0.300 ± 0.010)
0.254 ± 0.0127
(0.010 ± 0.0005)
0.65
(0.0255)
4.445 ± 0.127
(0.175 ± 0.005)
Dimensions
mm
(inches)
0.813 ± 0.102
(0.032 ± 0.004)
LAA100PL
2.540 ± 0.127
(0.100 ± 0.005)
6.350 ± 0.127
(0.250 ± 0.005)
0 MIN / 0.102 MAX
(0 MIN / 0.004 MAX)
9.398 ± 0.127
(0.370 ± 0.005)
Pin 1
9.652 ± 0.381
(0.380 ± 0.015)
7.620 ± 0.254
(0.300 ± 0.010)
2.286 MAX.
(0.090 MAX.)
2.54
(0.10)
0.635 ± 0.127
(0.025 ± 0.005)
0.203 ± 0.013
(0.008 ± 0.0005)
8.70
(0.3425)
1.55
(0.0610)
0.65
(0.0255)
2.159 ± 0.025
(0.085 ± 0.001)
0.457 ± 0.076
(0.018 ± 0.003)
0.864 ± 0.120
(0.034 ± 0.004)
6
PCB Land Pattern
Dimensions
mm
(inches)
www.ixysic.com
R02
INTEGRATED CIRCUITS DIVISION
LAA100L
LAA100LSTR Tape & Reel
330.2 DIA.
(13.00 DIA.)
Top Cover
Tape Thickness
0.102 MAX.
(0.004 MAX.)
W=16.00
(0.63)
Bo=10.30
(0.406)
K0 =4.90
(0.193)
Ao=10.30
(0.406)
K1 =4.20
(0.165)
Embossed Carrier
Embossment
P=12.00
(0.472)
User Direction of Feed
Dimensions
mm
(inches)
NOTES:
1. Dimensions carry tolerances of EIA Standard 481-2
2. Tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2
LAA100PLTR Tape & Reel
2.00
(0.079)
330.2 DIA.
(13.00 DIA.)
Top Cover
Tape Thickness
0.102 MAX.
(0.004 MAX.)
Embossment
W = 16.00
(0.63)
7.50
(0.295)
Bo = 10.30
(0.406)
K0 = 2.70
(0.106)
K1 = 2.00
(0.079)
Embossed Carrier
4.00
(0.157)
Ao = 10.30
(0.406)
P = 12.00
(0.472)
User Direction of Feed
Dimensions
mm
(inches)
NOTES:
1. All dimensions carry tolerances of EIA Standard 481-2
2. The tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2
For additional information please visit our website at: www.ixysic.com
IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make
changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated
Circuits Division’s Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its
products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other
applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division’s product may result in direct physical harm, injury, or death to a person or severe
property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice.
7
Specification: DS-LAA100L-R02
©Copyright 2012, IXYS Integrated Circuits Division
OptoMOS® is a registered trademark of IXYS Integrated Circuits Division
All rights reserved. Printed in USA.
12/22/2012