VISHAY RMB4S

PATENT PENDING
PATENT PENDING
PATENT PENDING
RMB2S THRU RMB4S
MINIATURE GLASS PASSIVATED SINGLE-PHASE SURFACE MOUNT
FAST RECOVERY BRIDGE RECTIFIER
Reverse Voltage - 200 to 400 Volts
0.029 (0.74)
0.017 (0.43)
Forward Current - 0.5 Ampere
Case Style MBS
FEATURES
0.272 (6.90)
0.252 (6.40)
0.161 (4.10)
0.144 (3.65)
0.205 (5.21)
0.195 (4.95)
0.105 (2.67)
0.095 (2.41)
0.049 (1.24)
0.039 (0.99)
0.195 (4.95)
0.179 (4.55)
0.062 (1.57)
0.058 (1.47)
o
♦ Plastic package has Underwriters Laboratory Flammability
Classification 94V-0
♦ This series is UL recognized under Component Index,
file number E54214
♦ Glass passivated chip junctions
♦ High surge overload rating: 35A peak
♦ Saves space on printed circuit boards
♦ Fast recovery, low loss switching
♦ High temperature soldering guaranteed:
260°C/10 seconds at 5 lbs. (2.3kg) tension
0-8
0.038 (0.96)
0.019 (0.48)
4 (2.90) 0.106 (2.70)
4 (2.40) 0.090 (2.30)
0.008 (0.20)
0.004 (0.10)
0.117 (2.97)
0.107 (2.72)
0.0075 (0.19)
0.0065 (0.16)
MECHANICAL DATA
0.016 (0.41)
0.006 (0.15)
0.018 (0.46)
0.014 (0.36)
0.058 (1.47)
0.054 (1.37)
Dimensions in inches and (millimeters)
Case: Molded plastic body over passivated junctions
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Polarity: Polarity symbols marked on body
Mounting Position: Any
Weight: 0.0078 ounce, 0.22 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
SYMBOLS
RMB2S
R2
R4
Maximum repetitive peak reverse voltage
VRRM
200
400
Volts
Maximum RMS voltage
VRMS
140
280
Volts
Maximum DC blocking voltage
VDC
200
400
Volts
Maximum average forward output rectified
- on glass-epoxy P.C.B. (NOTE 1)
current at TA=30°C
- on aluminum substrate (NOTE 2)
I(AV)
0.5
0.8
Amp
Peak forward surge current 8.3msec single half sinewave superimposed on rated load (JEDEC Method)
IFSM
30.0
Amps
Rating for fusing (t<8.3ms)
I2t
5.0
A2sec
Maximum instantaneous forward voltage drop
per leg at 0.4A
VF
1.25
Volts
IR
5.0
100
Maximum reverse recovery time (NOTE 3)
trr
150
ns
Typical junction capacitance per leg (NOTE 4)
CJ
13.0
pF
RΘJA
RΘJA
RΘJL
85.0
70.0
20.0
°C/W
TJ, TSTG
-55 to +150
°C
Device marking code
Maximum DC reverse current at
rated DC blocking voltage per leg
Typical thermal resistance per leg
TA=25°C
TA=125°C
(NOTE 1)
(NOTE 2)
(NOTE 1)
Operating junction and storage temperature range
NOTES:
(1) On glass epoxy P.C.B. mounted on 0.05 x 0.05" (1.3 x 1.3mm) pads
(2) On aluminum substrate P.C.B. with an area of 0.8 x 0.8" (2.0 x 2.0mm) mounted on 0.05 x 0.05” (1.3 x 1.3mm) solder pad
(3) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A
(4) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
9/8/98
RMB4S
UNITS
RATINGS AND CHARACTERISTIC CURVES RMB2S THRU RMB4S
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE
CURRENT PER LEG
0.8
35
PEAK FORWARD SURGE CURRENT,
AMPERES
AVERAGE FORWARD RECTIFIED CURRENT,
AMPERES
FIG. 1 - DERATING CURVE FOR OUTPUT
RECTIFIED CURRENT
0.7
GLASS
EPOXY
P.C.B.
0.6
0.5
0.4
0.3
0.2
0.1
RESISTIVE OR INDUCTIVE LOAD
0
0
20
40
60
25
20
f=60 HZ
15
10
1.0 CYCLE
NUMBER OF CYCLES
INSTANTANEOUS FORWARD CURRENT,
AMPERES
10
TJ=150°C
TJ=25°C
0.1
PULSE WIDTH=300µs
1% DUTY CYCLE
0.4
0.6
0.8
1.0
1.4
1.2
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
PER LEG
JUNCTION CAPACITANCE, pF
30
TJ=25°C
f=1.0 MHz
Vsig=50mVp-p
20
15
10
5.0
0
0.1
1
10
REVERSE VOLTAGE, VOLTS
FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS
PER LEG
100
TJ=125°C
10
1
0.1
TJ=25°C
0.01
0
20
40
60
80
100
120
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
25
INSTANTANEOUS REVERSE LEAKAGE CURRENT,
MICROAMPERES
FIG. 3 - TYPICAL FORWARD VOLTAGE
CHARACTERISTICS PER LEG
0.01
0.2
100
10
1
AMBIENT TEMPERATURE, °C
1
f=50 HZ
5.0
0
80 100 120 140 160
TA=40°C
SINGLE HALF SINE-WAVE
(JEDEC Method)
30
100 200
140
160