ZTA4.0MG SCOPE （范围） This 2. 3. specification is applied to the ceramics resonator used for microcomputer （本规格书适用于微电子用陶瓷谐振器） MODEL NAME （产品名称） Part No. (产品号) Customer`s Part No.(顾客产品号) Drawing No.(图号) ZTA4.0MG / JYD-083 DIMENSIONS （尺寸） 10.0 (MAX) 6.0 Z4.00M ) X A M ( 1. ± 5.0 0.5±0.1 1.0 5.0±0.3 0.3±0.1 4.0 (MAX) Materials(材料) Terminal(引脚) Sn plated on Cu（铜镀锡） Coating(涂料) Epoxy Resin（环氧树脂） Unit(单位)：mm http://www.luguang.cn Email:[email protected] ZTA4.0MG 4. ELECTRICAL CHARACTERISTICS （电气性能） Item （项目） Requirements （要求） 1 Oscillation Frequency(Fosc) （振荡频率） 2 Frequency Tolerance （频率公差） Fosc±0.5 % (MAX) 3 Resonator Impedance （谐振阻抗） 30 Ω (MAX) 4 Operating Temp. Range （工作温度范围） -25℃~+85℃ 5 Temperature Stability （温度稳定性） ±0.3% (MAX) (-25℃~+85℃) 6 Insulation Resistance (绝缘阻抗) 100MΩ min (D.C. 100V) 7 Aging(10 years) （10 年老化率） ±0.3 % 8 Storage Temp. Range （贮存温度范围） -40℃~+85℃ 9 Test Temp.&Humi.Condition (测试温、湿度条件) +10℃~+30℃、40%~80% 4.00 MHZ 5． TEST CIRCUIT (测试电路) Unless any necessity to measure under a standard condition(Temp:20±2℃.Humi.:65±5%)is occurred.( 必要时标准测量条件为温度 20± 2℃，相对湿度 65± 5%） VDD IC IC Output 1MΩ C1 IC：1/6CD4069UBE×2 C2 VDD= +5V(DC) C1=C2=30pF http://www.luguang.cn Email:[email protected] ZTA4.0MG 6. PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS （物理及环境特性） Test Item (试验项目) 1 Lead Strength （引脚强度） Lead Pulling （引脚拉力） Lead Bending （引脚弯曲） Condition of Test （试验条件） Force of 0.5kg is applied to each lead in axial direction for 10sec..（沿每个引脚轴向施加 0.5kg 力 保持 10 秒钟） When force of 0.25kg is applied to each lead in axial direction.the lead shall folded up to 90° from the axial direction and folded back to the axial direction. (沿引脚轴向施加 0.25kg 力的时候把引脚折弯 90 Requirements （要求） No mechanical damage and the measured values shall meet Table 1.(无机械损伤， 测量值满足表 1 要求) 度后再折回原形) Lead terminals are immersed in resin for 5 seconds and then immersing in a soldering bath(235±5℃)for 2 Solderability (可焊性) 5±0.5sec.(引脚在助剂内浸 5 秒后再浸入 235±5℃ 的锡炉内 5±0.5 秒) The solder shall coat at least 90% of the surface of terminal(引脚上 锡覆盖率≥90%) After being placed in a chamber with 85℃ for 100 3 Storage in High Temp. (高温贮存) hours and then being placed in natural condition for 1 hours, then measure.(85℃环境下存放 100 小时后取 出自然存放 1 小时测试) After being placed in a chamber with -25℃ for 100 4 Storage in Low Temp. (低温贮存) hours and then being placed in natural condition for 1 hours, then measure.(-25℃环境下存放 100 小时后 取出自然存放 1 小时测试) The measured value shall meet Table 1(测量值满 足表 1 要求) After being placed in a chamber （Humi.:90~95%RH,Temp.:40±2℃） for 100 5 Humidity (潮湿) hours and then being placed in natural condition for 1 hours, then measure. (温度 40±2℃；湿度 90~95%的 环境下存放 100 小时后取出自然存放 1 小时测试) http://www.luguang.cn Email:[email protected] ZTA4.0MG After temperature cycling of -55℃(30 minutes)to +85℃(30 minutes)was performed 5 times,Resonator 6 Thermal Shock (热冲击) shall be measured after being placed in natural condition for 1 hour(-55℃下 30 分钟到+85℃下 30 分钟循环 5 次后自然存放 1 小时测量) Lead terminals are immersed up to 2. 0 ㎜ from the root of terminals in solder bath of 265±5℃ for 7 Resistance to soldering Heat (耐焊接热) 10±1seconds, Resonator shall be measured after being placed in natural condition for 1 hour.( 引脚距 根部 2mm 以下浸入 265±5℃的锡炉中 10±1 秒取出 自然存放 1 小时测量) 8 Random Drop (自由跌落) 9 Vibration (振动) Resonator shall be measured after 3 times random dropping from the hight of 1 m to concrete floor.(谐 振器从 1 米高向水泥地板自由跌落 3 次后测量) Resonator shall be measured after being applied vibration as below:(谐振器做如下振动后测量) Vibration Freq.(振动频率): 10 Hz to 55 Hz Amplitude(幅度): 1.5mm Directions(方向): 3 axial directions（三轴向） Time(时间): 1 hour/each direction（1 小时/向） The measured value shall meet Table 1(测量值满 足表 1 要求) Table 1(表 1) Item (项目) Limit Value (限定值) Oscillation Frequency(Fosc) （振荡频率） ≤±0.3% Resonator Impedance （谐振阻抗） ≤±10Ω ※ Note: The limits in the above table are referenced to the initial measurements. （上表中的限定值参照初始测量值） http://www.luguang.cn Email:[email protected]