MIC24054 12V, 9A High-Efficiency Buck Regulator SuperSwitcher II General Description Features • Hyper Light Load efficiency – up to 80% at 10mA The Micrel MIC24054 is a constant-frequency, synchronous DC/DC buck regulator featuring adaptive on• Hyper Speed Control architecture enables time control architecture. The MIC24054 operates over a − High delta V operation (VIN = 19V and VOUT = 0.8V) supply range of 4.5V to 19V. It has an internal linear − Small output capacitance regulator which provides a regulated 5V to power the • Input voltage range: 4.5V to 19V internal control circuitry. The MIC24054 operates at a constant 600kHz switching frequency in continuous • Output current up to 9A conduction mode and can be used to provide up to 9A of • Up to 95% efficiency output current. The output voltage is adjustable down to • Adjustable output voltage from 0.8V to 5.5V 0.8V. • ±1% FB accuracy ® Micrel’s Hyper Light Load architecture provides the same • Any Capacitor stable − zero-to-high ESR high-efficiency and ultra-fast transient response as the • 600kHz switching frequency Hyper Speed Control architecture under medium to heavy loads, but also maintains high efficiency under light load • Power good (PG) output conditions by transitioning to variable frequency, • Foldback current-limit and “hiccup” mode short-circuit discontinuous mode operation. protection The MIC24054 offers a full suite of protection features to • Safe start-up into pre-biased loads ensure protection of the IC during fault conditions. These • –40°C to +125°C junction temperature range include undervoltage lockout to ensure proper operation • Available in 28-pin 5mm × 6mm QFN package under power-sag conditions, thermal shutdown, internal soft-start to reduce the inrush current, foldback current Applications limit and “hiccup mode” short-circuit protection. The MIC24054 includes a power good (PG) output to allow • Servers and work stations simple sequencing. • Routers, switches, and telecom equipment The 9A Hyper Speed Control part, MIC24053, is also • Base stations available on Micrel’s web site. All support documentation can be found on Micrel’s web site at: www.micrel.com. ___________________________________________________________________________________________________________ Typical Application Efficiency (VIN = 12V) vs. Output Current 100 95 5.0V 3.3V 2.5V 1.8V 1.5V 1.2V 1.0V 0.9V 0.8V EFFICIENCY (%) 90 85 80 75 70 65 60 55 VIN = 12V 50 0 2 4 6 8 10 12 OUTPUT CURRENT (A) Hyper Light Load is a registered trademark of Micrel, Inc. Hyper Speed Control, SuperSwitcher II, and Any Capacitor are trademarks of Micrel, Inc. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com October 2012 M9999-102512-A Micrel, Inc. MIC24054 Ordering Information Part Number Switching Frequency Voltage Package Junction Temperature Range Lead Finish MIC24054YJL 600kHz Adjustable 28-Pin 5mm × 6mm QFN –40°C to +125°C Pb-Free Pin Configuration 28-Pin 5mm x 6mm QFN (JL) (Top View) Pin Description Pin Number Pin Name 1 PVDD 5V Internal Linear Regulator output. PVDD supply is the power MOSFET gate drive supply voltage and created by internal LDO from VIN. When VIN < +5.5V, PVDD should be tied to PVIN pins. A 2.2µF ceramic capacitor from the PVDD pin to PGND (Pin 2) must be placed next to the IC. 2, 5, 6, 7, 8, 21 PGND Power Ground. PGND is the ground path for the MIC24054 buck converter power stage. The PGND pins connect to the low-side N-Channel internal MOSFET gate drive supply ground, the sources of the MOSFETs, the negative terminals of input capacitors, and the negative terminals of output capacitors. The loop for the power ground should be as small as possible and separate from the signal ground (SGND) loop. 3 NC No Connect. 4, 9, 10, 11, 12 SW Switch Node output. Internal connection for the high-side MOSFET source and low-side MOSFET drain. Due to the high speed switching on this pin, the SW pin should be routed away from sensitive nodes. PVIN High-Side N-internal MOSFET Drain Connection input. The PVIN operating voltage range is from 4.5V to 19V. Input capacitors between the PVIN pins and the power ground (PGND) are required and keep the connection short. BST Boost output. Bootstrapped voltage to the high-side N-channel MOSFET driver. A Schottky diode is connected between the PVDD pin and the BST pin. A boost capacitor of 0.1μF is connected between the BST pin and the SW pin. Adding a small resistor at the BST pin can slow down the turn-on time of high-side N-Channel MOSFETs. 13,14,15, 16,17,18,19 20 October 2012 Pin Function 2 M9999-102512-A Micrel, Inc. MIC24054 Pin Description (Continued) Pin Number Pin Name Pin Function 22 CS Current Sense input. The CS pin senses current by monitoring the voltage across the low-side MOSFET during the OFF-time. The current sensing is necessary for short circuit protection and zero current cross comparator. In order to sense the current accurately, connect the low-side MOSFET drain to SW using a Kelvin connection. The CS pin is also the high-side MOSFET’s output driver return. 23 SGND Signal Ground. SGND must be connected directly to the ground planes. Do not route the SGND pin to the PGND pad on the top layer, see PCB layout guidelines for details. 24 FB Feedback input. Input to the transconductance amplifier of the control loop. The FB pin is regulated to 0.8V. A resistor divider connecting the feedback to the output is used to adjust the desired output voltage. 25 PG Power Good output. Open drain output. The PG pin is externally tied with a resistor to VDD. A high output is asserted when VOUT > 92% of nominal. 26 EN Enable input. A logic level control of the output. The EN pin is CMOS-compatible. Logic high = enable, logic low = shutdown. In the off state, supply current of the device is greatly reduced (typically 5µA). The EN pin should not be left floating. 27 VIN Power Supply Voltage input. Requires bypass capacitor to SGND. 28 VDD 5V Internal Linear Regulator output. VDD supply is the supply bus for the IC control circuit. VDD is created by internal LDO from VIN. When VIN < +5.5V, VDD should be tied to PVIN pins. A 1µF ceramic capacitor from the VDD pin to SGND pins must be place next to the IC. October 2012 3 M9999-102512-A Micrel, Inc. MIC24054 Absolute Maximum Ratings(1) Operating Ratings(3) PVIN to PGND............................................... −0.3V to +29V VIN to PGND ................................................. −0.3V to PVIN PVDD, VDD to PGND ..................................... −0.3V to +6V VSW , VCS to PGND ............................. −0.3V to (PVIN +0.3V) VBST to VSW ........................................................ −0.3V to 6V VBST to PGND .................................................. −0.3V to 35V VFB, VPG to PGND ............................. −0.3V to (VDD + 0.3V) VEN to PGND ....................................... −0.3V to (VIN +0.3V) PGND to SGND............................................ −0.3V to +0.3V Junction Temperature .............................................. +150°C Storage Temperature (TS) ......................... −65°C to +150°C Lead Temperature (soldering, 10s) ............................ 260°C (2). ESD Rating ................................................ ESD Sensitive Supply Voltage (PVIN, VIN) .............................. 4.5V to 19V PVDD, VDD Supply Voltage (PVDD, VDD) ..... 4.5V to 5.5V Enable Input (VEN) .................................................. 0V to VIN Junction Temperature (TJ) ........................ −40°C to +125°C Maximum Power Dissipation ...................................... Note 4 (4) Package Thermal Resistance 5mm x 6mm QFN-28 (θJA) ................................ 28°C/W Electrical Characteristics(5) PVIN = VIN = VEN = 12V, VBST – VSW = 5V; TA = 25°C, unless noted. Bold values indicate −40°C ≤ TJ ≤ +125°C. Parameter Condition Min. Typ. Max. Units 19 V Power Supply Input 4.5 Input Voltage Range (VIN, PVIN) Quiescent Supply Current VFB = 1.5V (non-switching) Shutdown Supply Current VEN = 0V 450 750 µA 5 10 µA 5 5.4 V 4.2 4.5 VDD Supply Voltage VDD Output Voltage VDD UVLO Threshold VIN = 7V to 19V, IDD = 25mA 4.8 VDD Rising 3.7 VDD UVLO Hysteresis Dropout Voltage (VIN – VDD) 400 IDD = 25mA 380 V mV 600 mV 5.5 V DC/DC Controller Output-Voltage Adjust Range (VOUT) 0.8 Reference Feedback Reference Voltage 0°C ≤ TJ ≤ 85°C (±1.0%) 0.792 0.8 0.808 −40°C ≤ TJ ≤ 125°C (±1.5%) 0.788 0.8 0.812 V Load Regulation IOUT = 3A to 9A (Continuous Mode) 0.25 % Line Regulation VIN = 4.5V to 19V 0.25 % FB Bias Current VFB = 0.8V 50 500 nA Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5kΩ in series with 100pF. 3. The device is not guaranteed to function outside operating range. 4. PD(MAX) = (TJ(MAX) – TA)/ θJA, where θJA depends upon the printed circuit layout. A 5 square inch 4 layer, 0.62”, FR-4 PCB with 2oz finish copper weight per layer is used for the θJA. 5. Specification for packaged product only. October 2012 4 M9999-102512-A Micrel, Inc. MIC24054 Electrical Characteristics(5) (Continued) PVIN = VIN = VEN = 12V, VBST – VSW = 5V; TA = 25°C, unless noted. Bold values indicate −40°C ≤ TJ ≤ +125°C. Parameter Condition Min. Typ. Max. Units Enable Control 1.8 EN Logic Level High V 0.6 V 6 30 µA 600 750 kHz EN Logic Level Low EN Bias Current VEN = 12V Oscillator (6) VOUT = 2.5V (7) VFB = 0V 82 % VFB = 1.0V 0 % 300 ns 3 ms Switching Frequency Maximum Duty Cycle Minimum Duty Cycle 450 Minimum Off-Time Soft-Start Soft-Start time Short-Circuit Protection Peak Inductor Current-Limit Threshold Short-Circuit Current VFB = 0.8V, TJ = 25°C 12.5 VFB = 0.8V, TJ = 125°C 11.25 VFB = 0V 14 20 A 8 A Internal FETs Top-MOSFET RDS (ON) ISW = 3A 27 mΩ Bottom-MOSFET RDS (ON) ISW = 3A 10.5 mΩ SW Leakage Current VEN = 0V 60 µA VIN Leakage Current VEN = 0V 25 µA 95 %VOUT Power Good (PG) 85 PG Threshold Voltage Sweep VFB from Low to High 92 PG Hysteresis Sweep VFB from High to Low 5.5 %VOUT PG Delay Time Sweep VFB from Low to High 100 µs PG Low Voltage Sweep VFB < 0.9 × VNOM, IPG = 1mA 70 TJ Rising 160 °C 15 °C 200 mV Thermal Protection Over-Temperature Shutdown Over-Temperature Shutdown Hysteresis Notes: 6. Measured in test mode. 7. The maximum duty-cycle is limited by the fixed mandatory off-time tOFF of typically 300ns. October 2012 5 M9999-102512-A Micrel, Inc. MIC24054 Typical Characteristics VIN Shutdown Current vs. Input Voltage VIN Operating Supply Current vs. Input Voltage 10 40 0.8 0.6 0.4 VOUT = 1.8V 0.2 IOUT = 0A SWITCHING VEN = 0V REN = OPEN VDD VOLTAGE (V) SHUTDOWN CURRENT (µA) SUPPLY CURRENT (mA) 1.0 30 20 4 7 10 13 16 4 19 7 16 4 19 0.796 VOUT = 1.8V 0.5% 0.0% -0.5% 4 19 7 VOUT = 1.8V 10 13 16 4 19 550 VOUT = 1.8V 12 8 4 IOUT = 2A October 2012 19 19 95% 90% 85% VFB = 0.8V VEN = VIN 0 500 16 100% VPG THRESHOLD/VREF (%) EN INPUT CURRENT (µA) 600 13 PG/VREF Ratio vs. Input Voltage 16 650 10 INPUT VOLTAGE (V) Enable Input Current vs. Input Voltage 700 16 7 INPUT VOLTAGE (V) Switching Frequency vs. Input Voltage 13 5 0 INPUT VOLTAGE (V) 10 10 VOUT = 1.8V -1.0% 16 19 15 IOUT = 2A to 9A 0.792 16 20 IOUT = 2A 13 13 Output Current Limit vs. Input Voltage CURRENT LIMIT (A) 0.800 INPUT VOLTAGE (V) 10 INPUT VOLTAGE (V) 1.0% 7 7 Total Regulation vs. Input Voltage TOTAL REGULATION (%) FEEDBACK VOLTAGE (V) 13 10 INPUT VOLTAGE (V) 0.804 4 VFB = 0.9V IDD = 10mA 0.808 10 4 0 Feedback Voltage vs. Input Voltage 7 6 2 INPUT VOLTAGE (V) 4 8 10 0 0.0 FREQUENCY (kHz) VDD Output Voltage vs. Input Voltage 80% 4 7 10 13 INPUT VOLTAGE (V) 6 16 19 4 7 10 13 16 19 INPUT VOLTAGE (V) M9999-102512-A Micrel, Inc. MIC24054 Typical Characteristics (Continued) VIN Operating Supply Current vs. Temperature VIN Shutdown Current vs. Temperature 14 0.8 0.6 0.4 VIN = 12V VOUT = 1.8V 0.2 IOUT = 0A SWITCHING RISING 12 10 0.0 8 6 4 VIN = 12V IOUT = 0A VEN = 0V 2 0 -50 -25 0 25 50 75 100 3.9 FALLING 2.9 1.9 0.9 -25 0 25 50 75 100 125 -50 0 25 50 75 TEMPERATURE (°C) Feedback Voltage vs. Temperature Load Regulation vs. Temperature Line Regulation vs. Temperature 0.800 0.796 VIN = 12V VOUT = 1.8V 0.792 0.5% 0.0% VIN = 12V VOUT = 1.8V -0.5% IOUT =2A to 9A 50 75 -25 650 5 VDD (V) 6 600 0 25 50 75 100 125 TEMPERATURE (°C) October 2012 25 50 125 75 100 125 Output Current Limit vs. Temperature VIN = 12V VOUT = 1.8V 15 10 5 VIN = 12V VOUT = 1.8V 2 100 0 -25 IOUT =0A 500 75 -50 TEMPERATURE (°C) 4 IOUT = 2A 50 VIN = 4.5V to 19V VOUT = 1.8V 20 3 VIN = 12V VOUT = 1.8V 25 -0.4% VDD vs. Temperature 700 0 -0.3% TEMPERATURE (°C) Switching Frequency vs. Temperature -25 -0.2% -0.6% -50 125 TEMPERATURE (°C) 550 0.0% -0.1% IOUT = 2A 100 CURRENT LIMIT (A) 25 0.1% -0.5% -1.0% 0.788 0 125 0.2% IOUT = 2A -25 100 0.3% LINE REGULATION (%) LOAD REGULATION (%) 0.804 -50 -25 TEMPERATURE (°C) TEMPERATURE (°C) 1.0% -50 HYST -0.1 -50 125 0.808 FEEBACK VOLTAGE (V) 4.9 VDD THRESHOLD (V) SHUTDOWN CURRENT (µA) SUPPLY CURRENT (mA) 1.0 FREQUENCY (kHz) VDD UVLO Threshold vs. Temperature 0 -50 -25 0 25 50 75 TEMPERATURE (°C) 7 100 125 -50 -25 0 25 50 75 100 125 TEMPERATURE (°C) M9999-102512-A Micrel, Inc. MIC24054 Typical Characteristics (Continued) Feedback Voltage vs. Output Current Output Voltage vs. Output Current 1.0% 1.819 0.804 0.800 0.796 VIN = 12V VOUT = 1.8V LINE REGULATION (%) 1.814 OUTPUT VOLTAGE (V) 1.810 1.805 1.800 1.796 1.791 1.787 0.792 1.5 3 4.5 6 7.5 9 1.5 4.5 6 7.5 9 0 OUTPUT VOLTAGE (V) 650 600 550 VIN = 12V VOUT = 1.8V 8 4.6 4.2 TA 25ºC 85ºC 125ºC 3.8 3.4 2 Die Temperature* (VIN = 12V) vs. Output Current 4 6 8 10 3 5 6 8 9 4.5 6 7.5 9 VIN = 12V 3.0 2.5 VOUT = 3.3V 2.0 1.5 1.0 VOUT = 0.8V 0.5 0.0 0 3 3.5 POWER DISSIPATION (W) POWER DISSIPATION (W) DIE TEMPERATURE (°C) VIN = 12V VOUT = 1.8V OUTPUT CURRENT (A) 1.5 IC Power Dissipation (VIN = 12V) vs. Output Current VIN = 5V 2 VIN = 5V VOUT = 1.8V OUTPUT CURRENT (A) 3.5 0 20 0 12 80 20 9 40 IC Power Dissipation (VIN = 5V) vs. Output Current 40 7.5 60 OUTPUT CURRENT (A) OUTPUT CURRENT (A) 60 6 0 0 10 4.5 80 VIN = 5V VFB < 0.8V 3.0 500 3 Die Temperature* (VIN = 5V) vs. Output Current 5.0 6 1.5 OUTPUT CURRENT (A) Output Voltage (VIN = 5V) vs. Output Current 700 FREQUENCY (kHz) 3 OUTPUT CURRENT (A) Switching Frequency vs. Output Current 4 -0.5% -1.0% 0 OUTPUT CURRENT (A) 2 0.0% VIN = 4.5V to 19V VOUT = 1.8V 1.782 0 0.5% VIN = 12V VOUT = 1.8V DIE TEMPERATURE (°C) FEEDBACK VOLTAGE (V) 0.808 Line Regulation vs. Output Current 3.0 2.5 VOUT = 5.0V 2.0 1.5 1.0 0.5 VOUT = 0.8V 0.0 0 1.5 3 4.5 6 OUTPUT CURRENT (A) 7.5 9 0 1.5 3 4.5 6 7.5 9 OUTPUT CURRENT (A) Die Temperature* : The temperature measurement was taken at the hottest point on the MIC24054 case mounted on a 5 square inch 4 layer, 0.62”, FR-4 PCB with 2oz finish copper weight per layer, see Thermal Measurement section. Actual results will depend upon the size of the PCB, ambient temperature and proximity to other heat emitting components. October 2012 8 M9999-102512-A Micrel, Inc. MIC24054 Typical Characteristics (Continued) Efficiency (VIN = 12V) vs. Output Current Efficiency (VIN = 5V) vs. Output Current 100 100 3.3V 2.5V 1.8V 1.5V 1.2V 1.0V 0.9V 0.8V 85 80 75 70 5.0V 3.3V 2.5V 1.8V 1.5V 1.2V 1.0V 0.9V 0.8V 90 EFFICIENCY (%) 90 65 85 80 75 70 65 60 60 55 VIN = 5V 55 0 2 4 6 8 10 8 6 4 10 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Thermal Derating* vs. Ambient Temperature Thermal Derating* vs. Ambient Temperature 14 OUTPUT CURRENT (A) 1.8V 10 8 3.3V 6 4 VIN = 5V VOUT = 1.8, 2.5, 3.3V 2 -25 0 25 50 75 100 AMBIENT TEMPERATURE (°C) 125 VIN = 5V VOUT = 0.8, 1.2, 1.5V -50 -25 0 25 50 75 100 125 AMBIENT TEMPERATURE (°C) Thermal Derating* vs. Ambient Temperature 12 0.8V 10 8 1.8V 6 4 VIN = 12V VOUT = 0.8, 1.2, 1.8V 12 2.5V 10 5V 8 6 4 VIN = 12V VOUT = 2.5, 3.3, 5V 2 0 -50 4 14 2 0 1.5V 6 12 14 12 8 0 2 0 12 0.8V 10 VIN = 12V 50 50 12 2 OUTPUT CURRENT (A) EFFICIENCY (%) 14 95 OUTPUT CURRENT (A) 95 OUTPUT CURRENT (A) Thermal Derating* vs. Ambient Temperature 0 -50 -25 0 25 50 75 100 AMBIENT TEMPERATURE (°C) 125 -50 -25 0 25 50 75 100 125 AMBIENT TEMPERATURE (°C) Die Temperature* : The temperature measurement was taken at the hottest point on the MIC24054 case mounted on a 5 square inch 4 layer, 0.62”, FR-4 PCB with 2oz finish copper weight per layer, see Thermal Measurement section. Actual results will depend upon the size of the PCB, ambient temperature and proximity to other heat emitting components. October 2012 9 M9999-102512-A Micrel, Inc. MIC24054 Functional Characteristics October 2012 10 M9999-102512-A Micrel, Inc. MIC24054 Functional Characteristics (Continued) October 2012 11 M9999-102512-A Micrel, Inc. MIC24054 Functional Characteristics (Continued) October 2012 12 M9999-102512-A Micrel, Inc. MIC24054 Functional Diagram Figure 1. MIC24054 Block Diagram October 2012 13 M9999-102512-A Micrel, Inc. MIC24054 The maximum duty cycle is obtained from the 300ns tOFF(min): Functional Description The MIC24054 is an adaptive ON-time synchronous step-down DC/DC regulator with an internal 5V linear regulator and a Power Good (PG) output. It is designed to operate over a wide input voltage range from 4.5V to 19V and provides a regulated output voltage at up to 9A of output current. An adaptive ON-time control scheme is employed in to obtain a constant switching frequency and to simplify the control compensation. Over-current protection is implemented without the use of an external sense resistor. The device includes an internal soft-start function which reduces the power supply input surge current at start-up by controlling the output voltage rise time. Dmax = = 1- 300ns tS Eq. 2 It is not recommended to use MIC24054 with a OFF-time close to tOFF(min) during steady-state operation. Also, as VOUT increases, the internal ripple injection will increase and reduce the line regulation performance. Therefore, the maximum output voltage of the MIC24054 should be limited to 5.5V and the maximum external ripple injection should be limited to 200mV. Please refer to “Setting Output Voltage” subsection in Application Information for more details. The actual ON-time and resulting switching frequency will vary with the part-to-part variation in the rise and fall times of the internal MOSFETs, the output load current, and variations in the VDD voltage. Also, the minimum tON results in a lower switching frequency in high VIN to VOUT applications, such as 18V to 1.0V. The minimum tON measured on the MIC24054 evaluation board is about 100ns. During load transients, the switching frequency is changed due to the varying OFF-time. To illustrate the control loop operation, we will analyze both the steady-state and load transient scenarios. Figure 2 shows the MIC24054 control loop timing during steady-state operation. During steady-state, the gm amplifier senses the feedback voltage ripple, which is proportional to the output voltage ripple and the inductor current ripple, to trigger the ON-time period. The ONtime is predetermined by the tON estimator. The termination of the OFF-time is controlled by the feedback voltage. At the valley of the feedback voltage ripple, which occurs when VFB falls below VREF, the OFF period ends and the next ON-time period is triggered through the control logic circuitry. Continuous Mode In continuous mode, the output voltage is sensed by the MIC24054 feedback pin FB via the voltage divider R1 and R2, and compared to a 0.8V reference voltage VREF at the error comparator through a low gain transconductance (gm) amplifier. If the feedback voltage decreases and the output of the gm amplifier is below 0.8V, then the error comparator will trigger the control logic and generate an ON-time period. The ON-time period length is predetermined by the “FIXED tON ESTIMATION” circuitry: VOUT VIN × 600kHz tS where tS = 1/600kHz = 1.66μs. Theory of Operation The MIC24054 is able to operate in either continuous mode or discontinuous mode. The operating mode is determined by the output of the Zero Cross comparator (ZC) as shown in Figure 1. t ON(estimated) = t S - t OFF(min) Eq. 1 where VOUT is the output voltage and VIN is the power stage input voltage. At the end of the ON-time period, the internal high-side driver turns off the high-side MOSFET and the low-side driver turns on the low-side MOSFET. The OFF-time period length depends upon the feedback voltage in most cases. When the feedback voltage decreases and the output of the gm amplifier is below 0.8V, the ON-time period is triggered and the OFF-time period ends. If the OFF-time period determined by the feedback voltage is less than the minimum OFF-time tOFF(min), which is about 300ns, the MIC24054 control logic will apply the tOFF(min) instead. tOFF(min) is required to maintain enough energy in the boost capacitor (CBST) to drive the high-side MOSFET. October 2012 14 M9999-102512-A Micrel, Inc. MIC24054 Unlike true current-mode control, the MIC24054 uses the output voltage ripple to trigger an ON-time period. The output voltage ripple is proportional to the inductor current ripple if the ESR of the output capacitor is large enough. The MIC24054 control loop has the advantage of eliminating the need for slope compensation. In order to meet the stability requirements, the MIC24054 feedback voltage ripple should be in phase with the inductor current ripple and large enough to be sensed by the gm amplifier and the error comparator. The recommended feedback voltage ripple is 20mV~100mV. If a low-ESR output capacitor is selected, then the feedback voltage ripple may be too small to be sensed by the gm amplifier and the error comparator. Also, the output voltage ripple and the feedback voltage ripple are not necessarily in phase with the inductor current ripple if the ESR of the output capacitor is very low. In these cases, ripple injection is required to ensure proper operation. Please refer to “Ripple Injection” subsection in Application Information for more details about the ripple injection technique. Figure 2. MIC24054 Control Loop Timing Figure 3 shows the operation of the MIC24054 during a load transient. The output voltage drops due to the sudden load increase, which causes the VFB to be less than VREF. This will cause the error comparator to trigger an ON-time period. At the end of the ON-time period, a minimum OFF-time tOFF(min) is generated to charge CBST since the feedback voltage is still below VREF. Then, the next ON-time period is triggered due to the low feedback voltage. Therefore, the switching frequency changes during the load transient, but returns to the nominal fixed frequency once the output has stabilized at the new load current level. With the varying duty cycle and switching frequency, the output recovery time is fast and the output voltage deviation is small in MIC24054 converter. Discontinuous Mode In continuous mode, the inductor current is always greater than zero; however, at light loads the MIC24054 is able to force the inductor current to operate in discontinuous mode. Discontinuous mode is where the inductor current falls to zero, as indicated by trace (IL) shown in Figure 4. During this period, the efficiency is optimized by shutting down all the non-essential circuits and minimizing the supply current. The MIC24054 wakes up and turns on the high-side MOSFET when the feedback voltage VFB drops below 0.8V. The MIC24054 has a zero crossing comparator that monitors the inductor current by sensing the voltage drop across the low-side MOSFET during its ON-time. If the VFB > 0.8V and the inductor current goes slightly negative, then the MIC24054 automatically powers down most of the IC circuitry and goes into a low-power mode. Once the MIC24054 goes into discontinuous mode, both LSD and HSD are low, which turns off the high-side and low-side MOSFETs. The load current is supplied by the output capacitors and VOUT drops. If the drop of VOUT causes VFB to go below VREF, then all the circuits will wake up into normal continuous mode. First, the bias currents of most circuits reduced during the discontinuous mode are restored, then a tON pulse is triggered before the drivers are turned on to avoid any possible glitches. Finally, the high-side driver is turned on. Figure 4 shows the control loop timing in discontinuous mode. Figure 3. MIC24054 Load Transient Response October 2012 15 M9999-102512-A Micrel, Inc. MIC24054 Current Limit The MIC24054 uses the RDS(ON) of the internal low-side power MOSFET to sense over-current conditions. This method will avoid adding cost, board space and power losses taken by a discrete current sense resistor. The low-side MOSFET is used because it displays much lower parasitic oscillations during switching than the high-side MOSFET. In each switching cycle of the MIC24054 converter, the inductor current is sensed by monitoring the low-side MOSFET in the OFF period. If the inductor current is greater than 14A, then the MIC24054 turns off the highside MOSFET and a soft-start sequence is triggered. This mode of operation is called “hiccup mode” and its purpose is to protect the downstream load in case of a hard short. The load current-limit threshold has a fold back characteristic related to the feedback voltage as shown in Figure 5. Figure 4. MIC24054 Control Loop Timing (Discontinuous Mode) Current Limit Threshold vs. Feedback Voltage CURRENT LIMIT THRESHOLD (A) 20 During discontinuous mode, the zero crossing comparator and the current limit comparator are turned off. The bias current of most circuits are reduced. As a result, the total power supply current during discontinuous mode is only about 450μA, allowing the MIC24054 to achieve high efficiency in light load applications. 16 12 VDD Regulator The MIC24054 provides a 5V regulated output for input voltage VIN ranging from 5.5V to 19V. When VIN < 5.5V, VDD should be tied to PVIN pins to bypass the internal linear regulator. 4 0 0.0 0.2 0.4 0.6 0.8 1.0 FEEDBACK VOLTAGE (V) Soft-Start Soft-start reduces the power supply input surge current at startup by controlling the output voltage rise time. The input surge appears while the output capacitor is charged up. A slower output rise time will draw a lower input surge current. The MIC24054 implements an internal digital soft-start by making the 0.8V reference voltage VREF ramp from 0 to 100% in about 3ms with 9.7mV steps. Therefore, the output voltage is controlled to increase slowly by a staircase VFB ramp. Once the soft-start cycle ends, the related circuitry is disabled to reduce current consumption. VDD must be powered up at the same time or after VIN to make the soft-start function correctly. October 2012 8 Figure 5. MIC24054 Current-Limit Foldback Characteristic Power-Good (PG) The Power Good (PG) pin is an open drain output which indicates logic high when the output is nominally 92% of its steady state voltage. A pull-up resistor of more than 10kΩ should be connected from PG to VDD. 16 M9999-102512-A Micrel, Inc. MIC24054 MOSFET Gate Drive The Block Diagram (Figure 1) shows a bootstrap circuit, consisting of D1 (a Schottky diode is recommended) and CBST. This circuit supplies energy to the high-side drive circuit. Capacitor CBST is charged, while the low-side MOSFET is on, and the voltage on the SW pin is approximately 0V. When the high-side MOSFET driver is turned on, energy from CBST is used to turn the MOSFET on. As the high-side MOSFET turns on, the voltage on the SW pin increases to approximately VIN. Diode D1 is reverse biased and CBST floats high while continuing to keep the high-side MOSFET on. The bias current of the high-side driver is less than 10mA so a 0.1μF to 1μF is sufficient to hold the gate voltage with minimal droop for the power stroke (high-side switching) cycle, i.e. ΔBST = 10mA x 1.67μs/0.1μF = 167mV. When the low-side MOSFET is turned back on, CBST is recharged through D1. A small resistor RG, which is in series with CBST, can be used to slow down the turn-on time of the high-side N-channel MOSFET. The drive voltage is derived from the VDD supply voltage. The nominal low-side gate drive voltage is VDD and the nominal high-side gate drive voltage is approximately VDD – VDIODE, where VDIODE is the voltage drop across D1. An approximate 30ns delay between the high-side and low-side driver transitions is used to prevent current from simultaneously flowing unimpeded through both MOSFETs. October 2012 17 M9999-102512-A Micrel, Inc. MIC24054 Maximizing efficiency requires the proper selection of core material and minimizing the winding resistance. The high frequency operation of the MIC24054 requires the use of ferrite materials for all but the most cost sensitive applications. Lower cost iron powder cores may be used but the increase in core loss will reduce the efficiency of the power supply. This is especially noticeable at low output power. The winding resistance decreases efficiency at the higher output current levels. The winding resistance must be minimized although this usually comes at the expense of a larger inductor. The power dissipated in the inductor is equal to the sum of the core and copper losses. At higher output loads, the core losses are usually insignificant and can be ignored. At lower output currents, the core losses can be a significant contributor. Core loss information is usually available from the magnetics vendor. Copper loss in the inductor is calculated by Equation 7: Application Information Inductor Selection Values for inductance, peak, and RMS currents are required to select the output inductor. The input and output voltages and the inductance value determine the peak-to-peak inductor ripple current. Generally, higher inductance values are used with higher input voltages. Larger peak-to-peak ripple currents will increase the power dissipation in the inductor and MOSFETs. Larger output ripple currents will also require more output capacitance to smooth out the larger ripple current. Smaller peak-to-peak ripple currents require a larger inductance value and therefore a larger and more expensive inductor. A good compromise between size, loss and cost is to set the inductor ripple current to be equal to 20% of the maximum output current. The inductance value is calculated by Equation 3: 2 L= PINDUCTOR(Cu) = IL(RMS) × RWINDING VOUT × (VIN(max) − VOUT ) VIN(max) × fsw × 20% × IOUT(max) Eq. 3 The resistance of the copper wire, RWINDING, increases with the temperature. The value of the winding resistance used should be at the operating temperature. where: fSW = switching frequency, 600kHz 20% = ratio of AC ripple current to DC output current VIN(max) = maximum power stage input voltage The peak-to-peak inductor current ripple is: ∆IL(pp) = VOUT × (VIN(max) − VOUT ) VIN(max) × fsw × L PWINDING(Ht) = RWINDING(20°C) × (1 + 0.0042 × (TH – T20°C)) Eq. 8 where: TH = temperature of wire under full load T20°C = ambient temperature RWINDING(20°C) = room temperature winding resistance (usually specified by the manufacturer) Eq. 4 The peak inductor current is equal to the average output current plus one half of the peak-to-peak inductor current ripple. IL(pk) =IOUT(max) + 0.5 × ΔIL(pp) Output Capacitor Selection The type of the output capacitor is usually determined by its equivalent series resistance (ESR). Voltage and RMS current capability are two other important factors for selecting the output capacitor. Recommended capacitor types are tantalum, low-ESR aluminum electrolytic, OSCON and POSCAP. The output capacitor’s ESR is usually the main cause of the output ripple. The output capacitor ESR also affects the control loop from a stability point of view. Eq. 5 2 The RMS inductor current is used to calculate the I R losses in the inductor. 2 IL(RMS) = IOUT(max) + October 2012 ΔIL(PP) 12 Eq. 7 2 Eq. 6 18 M9999-102512-A Micrel, Inc. MIC24054 Input Capacitor Selection The input capacitor for the power stage input VIN should be selected for ripple current rating and voltage rating. Tantalum input capacitors may fail when subjected to high inrush currents, caused by turning the input supply on. A tantalum input capacitor’s voltage rating should be at least two times the maximum input voltage to maximize reliability. Aluminum electrolytic, OS-CON, and multilayer polymer film capacitors can handle the higher inrush currents without voltage de-rating. The input voltage ripple will primarily depend on the input capacitor’s ESR. The peak input current is equal to the peak inductor current, so: The maximum value of ESR is calculated: ESR COUT ≤ ΔVOUT(pp) Eq. 9 ΔIL(PP) where: ΔVOUT(pp) = peak-to-peak output voltage ripple ΔIL(PP) = peak-to-peak inductor current ripple The total output ripple is a combination of the ESR and output capacitance. The total ripple is calculated in Equation 10: 2 ΔVIN = IL(pk) × ESRCIN ΔIL(PP) 2 + ΔIL(PP) × ESR C ΔVOUT(pp) = OUT C × f × 8 OUT SW Eq. 10 ( ) The input capacitor must be rated for the input current ripple. The RMS value of input capacitor current is determined at the maximum output current. Assuming the peak-to-peak inductor current ripple is low: where: D = Duty cycle COUT = Output capacitance value fSW = Switching frequency ICIN(RMS) ≈ IOUT(max) × D × (1 − D) 2 ΔIL(PP) Eq. 14 The power dissipated in the input capacitor is: PDISS(CIN) = ICIN(RMS) × ESRCIN As described in the “Theory of Operation” subsection in the Functional Description section, the MIC24054 requires at least 20mV peak-to-peak ripple at the FB pin to make the gm amplifier and the error comparator behave properly. Also, the output voltage ripple should be in phase with the inductor current. Therefore, the output voltage ripple caused by the output capacitors value should be much smaller than the ripple caused by the output capacitor ESR. If low-ESR capacitors, such as ceramic capacitors, are selected as the output capacitors, a ripple injection method should be applied to provide the enough feedback voltage ripple. Please refer to the “Ripple Injection” subsection for more details. The voltage rating of the capacitor should be twice the output voltage for a tantalum and 20% greater for aluminum electrolytic or OS-CON. The output capacitor RMS current is calculated below: ICOUT (RMS) = Eq. 13 Eq. 15 Ripple Injection The VFB ripple required for proper operation of the MIC24054 gm amplifier and error comparator is 20mV to 100mV. However, the output voltage ripple is generally designed as 1% to 2% of the output voltage. For a low output voltage, such as a 1V, the output voltage ripple is only 10mV to 20mV, and the feedback voltage ripple is less than 20mV. If the feedback voltage ripple is so small that the gm amplifier and error comparator can’t sense it, then the MIC24054 will lose control and the output voltage is not regulated. In order to have some amount of VFB ripple, a ripple injection method is applied for low output voltage ripple applications. Eq. 11 12 The power dissipated in the output capacitor is: 2 PDISS(COUT ) = ICOUT (RMS) × ESR COUT October 2012 Eq. 12 19 M9999-102512-A Micrel, Inc. MIC24054 The applications are divided into three situations according to the amount of the feedback voltage ripple: 1. Enough ripple at the feedback voltage due to the large ESR of the output capacitors. As shown in Figure 6, the converter is stable without any ripple injection. The feedback voltage ripple is: Figure 8. Invisible Ripple at FB ΔVFB(pp) R2 = × ESR COUT × ΔIL (pp) R1 + R2 Eq. 16 In this situation, the output voltage ripple is less than 20mV. Therefore, additional ripple is injected into the FB pin from the switching node SW via a resistor Rinj and a capacitor Cinj, as shown in Figure 8. The injected ripple is: where: ΔIL(pp) is the peak-to-peak value of the inductor current ripple. 2. Inadequate ripple at the feedback voltage due to the small ESR of the output capacitors. ΔVFB(pp) = VIN × K div × D × (1 - D) × The output voltage ripple is fed into the FB pin through a feedforward capacitor Cff in this situation, as shown in Figure 7. The typical Cff value is between 1nF and 100nF. With the feedforward capacitor, the feedback voltage ripple is very close to the output voltage ripple: ΔVFB(pp) ≈ ESR × ΔIL (pp) K div = R1//R2 R inj + R1//R2 1 fSW × τ Eq. 18 Eq. 19 where: VIN = Power stage input voltage D = Duty cycle fSW = Switching frequency τ = (R1//R2//Rinj) × Cff Eq. 17 3. Virtually no ripple at the FB pin voltage due to the very low ESR of the output capacitors. In Equations 18 and 19, it is assumed that the time constant associated with Cff must be much greater than the switching period: 1 T = << 1 fSW × τ τ Eq. 20 If the voltage divider resistors R1 and R2 are in the kΩ range, a Cff of 1nF to 100nF can easily satisfy the large time constant requirements. Also, a 100nF injection capacitor Cinj is used in order to be considered as short for a wide range of the frequencies. Figure 6. Enough Ripple at FB Figure 7. Inadequate Ripple at FB October 2012 20 M9999-102512-A Micrel, Inc. MIC24054 The process of sizing the ripple injection resistor and capacitors is: Step 1. Select Cff to feed all output ripples into the feedback pin and make sure the large time constant assumption is satisfied. Typical choice of Cff is 1nF to 100nF if R1 and R2 are in kΩ range. Step 2. Select Rinj according to the expected feedback voltage ripple using Equation 19: K div = ΔVFB(pp) VIN × fSW × τ D × (1 - D) In addition to the external ripple injection added at the FB pin, internal ripple injection is added at the inverting input of the comparator inside the MIC24054, as shown in Figure 10. The inverting input voltage VINJ is clamped to 1.2V. As VOUT is increased, the swing of VINJ will be clamped. The clamped VINJ reduces the line regulation because it is reflected as a DC error on the FB terminal. Therefore, the maximum output voltage of the MIC24054 should be limited to 5.5V to avoid this problem. Eq. 21 Then the value of Rinj is obtained as: R inj = (R1//R2) × ( 1 K div − 1) Eq. 22 Step 3. Select Cinj as 100nF, which could be considered as short for a wide range of the frequencies. Setting Output Voltage The MIC24054 requires two resistors to set the output voltage as shown in Figure 9. The output voltage is determined by Equation 23: VOUT = VFB R1 ) × (1 + R2 Figure 10. Internal Ripple Injection Thermal Measurements Measuring the IC’s case temperature is recommended to insure it is within its operating limits. Although this might seem like a very elementary task, it is easy to get erroneous results. The most common mistake is to use the standard thermal couple that comes with a thermal meter. This thermal couple wire gauge is large, typically 22 gauge, and behaves like a heatsink, resulting in a lower case measurement. Two methods of temperature measurement are using a smaller thermal couple wire or an infrared thermometer. If a thermal couple wire is used, then it must be constructed of 36 gauge wire or higher then (smaller wire size) to minimize the wire heat-sinking effect. In addition, the thermal couple tip must be covered in either thermal grease or thermal glue to make sure that the thermal couple junction is making good contact with the case of the IC. Omega brand thermal couple (5SC-TT-K36-36) is adequate for most applications. Wherever possible, an infrared thermometer is recommended. The measurement spot size of most infrared thermometers is too large for an accurate reading on a small form factor ICs. However, a IR thermometer from Optris has a 1mm spot size, which makes it a good choice for measuring the hottest point on the case. An optional stand makes it easy to hold the beam on the IC for long periods of time. Eq. 23 where: VFB = 0.8V. A typical value of R1 can be between 3kΩ and 10kΩ. If R1 is too large, it may allow noise to be introduced into the voltage feedback loop. If R1 is too small, it will decrease the efficiency of the power supply, especially at light loads. Once R1 is selected, R2 can be calculated using Equation 24: R2 = VFB × R1 VOUT − VFB Eq. 24 Figure 9. Voltage-Divider Configuration October 2012 21 M9999-102512-A Micrel, Inc. MIC24054 Inductor PCB Layout Guidelines Warning!!! To minimize EMI and output noise, follow these layout recommendations. PCB Layout is critical to achieve reliable, stable and efficient performance. A ground plane is required to control EMI and minimize the inductance in power, signal and return paths. The following guidelines should be followed to insure proper operation of the MIC24054 regulator. IC • A 2.2µF ceramic capacitor, which is connected to the PVDD pin, must be located right at the IC. The PVDD pin is very noise sensitive and placement of the capacitor is very critical. Use wide traces to connect to the PVDD and PGND pins. • A 1µF ceramic capacitor must be placed right between VDD and the signal ground SGND. The SGND must be connected directly to the ground planes. Do not route the SGND pin to the PGND Pad on the top layer. • Place the IC close to the point-of-load (POL). • Use fat traces to route the input and output power lines. • Signal and power grounds should be kept separate and connected at only one location. Place the input capacitor next. • Place the input capacitors on the same side of the board and as close to the IC as possible. • Keep both the PVIN pin and PGND connections short. • Place several vias to the ground plane close to the input capacitor ground terminal. • Use either X7R or X5R dielectric input capacitors. Do not use Y5V or Z5U type capacitors. • Do not replace the ceramic input capacitor with any other type of capacitor. Any type of capacitor can be placed in parallel with the input capacitor. • If a Tantalum input capacitor is placed in parallel with the input capacitor, it must be recommended for switching regulator applications and the operating voltage must be derated by 50%. • In “Hot-Plug” applications, a Tantalum or Electrolytic bypass capacitor must be used to limit the overvoltage spike seen on the input supply with power is suddenly applied. October 2012 Keep the inductor connection to the switch node (SW) short. • Do not route any digital lines underneath or close to the inductor. • Keep the switch node (SW) away from the feedback (FB) pin. • The CS pin should be connected directly to the SW pin to accurate sense the voltage across the lowside MOSFET. • To minimize noise, place a ground plane underneath the inductor. • The inductor can be placed on the opposite side of the PCB with respect to the IC. It does not matter whether the IC or inductor is on the top or bottom as long as there is enough air flow to keep the power components within their temperature limits. The input and output capacitors must be placed on the same side of the board as the IC. Output Capacitor Input Capacitor • • • Use a wide trace to connect the output capacitor ground terminal to the input capacitor ground terminal. • Phase margin will change as the output capacitor value and ESR changes. Contact the factory if the output capacitor is different from what is shown in the BOM. • The feedback trace should be separate from the power trace and connected as close as possible to the output capacitor. Sensing a long high current load trace can degrade the DC load regulation. Optional RC Snubber • 22 Place the RC snubber on either side of the board and as close to the SW pin as possible. M9999-102512-A Micrel, Inc. MIC24054 Evaluation Board Schematic Figure 11. Schematic of MIC24054 Evaluation Board (J11, R13, R15 are for testing purposes) October 2012 23 M9999-102512-A Micrel, Inc. MIC24054 Evaluation Board Schematic (Continued) Figure 12. Schematic of MIC24054 Evaluation Board (J11, R13, R15 are for testing purposes) (Optimized for Smaller Footprint) October 2012 24 M9999-102512-A Micrel, Inc. MIC24054 Bill of Materials Item Part Number C1 Open 12103C475KAT2A C2, C3 GRM32DR71E475KA61K C3225X7R1E475K C13, C15 C6, C7, C10 GRM32ER60J107ME20L C12 C14 C11, C16 Murata (2) 4.7µF Ceramic Capacitor, X7R, Size 1210, 25V 2 100µF Ceramic Capacitor, X5R, Size 1210, 6.3V 2 0.1µF Ceramic Capacitor, X7R, Size 0603, 50V 3 1.0µF Ceramic Capacitor, X7R, Size 0603, 10V 1 2.2µF Ceramic Capacitor, X5R, Size 0603, 10V 1 4.7nF Ceramic Capacitor, X7R, Size 0603, 50V 1 220µF Aluminum Capacitor, 35V 1 40V, 350mA, Schottky Diode, SOD323 1 2.2µH Inductor, 15A Saturation Current 1 (3) TDK AVX Murata 06035C104KAT2A AVX GRM188R71H104KA93D GRM188R71A105KA61D Murata TDK AVX Murata C1608X7R1A105K TDK 0603ZD225KAT2A AVX GRM188R61A225KE34D Murata C1608X5R1A225K TDK 06035C472KAZ2A AVX GRM188R71H472K Murata C1608X7R1H472K TDK B41851F7227M (4) EPCOS Open SD103AWS D1 (1) TDK 0603ZC105KAT2A C9 Qty. AVX C3225X5R0J107M C1608X7R1H104K C8 Description Open 12106D107MAT2A C4, C5 Manufacturer SD103AWS-7 SD103AWS (5) MCC Diodes Inc (6) (7) Vishay Cooper Bussmann (8) L1 HCF1305-2R2-R R1 CRCW06032R21FKEA Vishay Dale 2.21Ω Resistor, Size 0603, 1% 1 R2 CRCW06032R00FKEA Vishay Dale 2.00Ω Resistor, Size 0603, 1% 1 R3 CRCW060319K6FKEA Vishay Dale 19.6kΩ Resistor, Size 0603, 1% 1 R4 CRCW06032K49FKEA Vishay Dale 2.49kΩ Resistor, Size 0603, 1% 1 R5 CRCW060320K0FKEA Vishay Dale 20.0kΩ Resistor, Size 0603, 1% 1 R6, R14, R17 CRCW060310K0FKEA Vishay Dale 10.0kΩ Resistor, Size 0603, 1% 3 R7 CRCW06034K99FKEA Vishay Dale 4.99kΩ Resistor, Size 0603, 1% 1 R8 CRCW06032K87FKEA Vishay Dale 2.87kΩ Resistor, Size 0603, 1% 1 R9 CRCW06032K006FKEA Vishay Dale 2.00kΩ Resistor, Size 0603, 1% 1 R10 CRCW06031K18FKEA Vishay Dale 1.18kΩ Resistor, Size 0603, 1% 1 R11 CRCW0603806RFKEA Vishay Dale 806Ω Resistor, Size 0603, 1% 1 R12 CRCW0603475RFKEA Vishay Dale 475Ω Resistor, Size 0603, 1% 1 October 2012 25 M9999-102512-A Micrel, Inc. MIC24054 Bill of Materials (Continued) Item Part Number Manufacturer R13 CRCW06030000FKEA Vishay Dale 0Ω Resistor, Size 0603, 5% 1 R15 CRCW060349R9FKEA Vishay Dale 49.9Ω Resistor, Size 0603, 1% 1 R16, R18 CRCW06031R21FKEA Vishay Dale 1.21Ω Resistor, Size 0603, 1% 2 R20 Open All Reference designators ending with “A” Open U1 MIC24054YJL 12V, 9A High-Efficiency Buck Regulator 1 (9) Micrel. Inc. Description Qty Notes: 1. AVX: www.avx.com. 2. Murata: www.murata.com. 3. TDK: www.tdk.com. 4. EPCOS: www.epcos.com. 5. MCC: www.mccsemi.com. 6. Diode Inc.: www.diodes.com. 7. Vishay: www.vishay.com. 8. Cooper Bussmann: www.cooperbussmann.com. 9. Micrel, Inc.: www.micrel.com. October 2012 26 M9999-102512-A Micrel, Inc. MIC24054 Recommended PCB Layout Figure 13. MIC24054 Evaluation Board Top Layer Figure 14. MIC24054 Evaluation Board Mid-Layer 1 (Ground Plane) October 2012 27 M9999-102512-A Micrel, Inc. MIC24054 Recommended PCB Layout (Continued) Figure 15. MIC24054 Evaluation Board Mid-Layer 2 Figure 16. MIC24054 Evaluation Board Bottom Layer October 2012 28 M9999-102512-A Micrel, Inc. MIC24054 Package Information(1) 28-Pin 5mm × 6mm QFN (JL) Note: 1. Package information is correct as of the publication date. For updates and most current information, go to www.micrel.com. October 2012 29 M9999-102512-A Micrel, Inc. MIC24054 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2012 Micrel, Incorporated. October 2012 30 M9999-102512-A