MOCH & MOCZ Series 1.5” Square, 5 Pin OCXO Oven Controlled Oscillator 500 KHz to 150.0 MHz Available SC Crystal -40°C to 85° Available ±5ppb to ±500ppb Frequency Range Frequency Stability Operating Temperature Storage Temperature Sine wave Output HCMOS Supply Voltage (Vdd) typ max Supply Current Warm-up Time Vc Input Impedance Crystal Phase Noise @ 30MHZ 100 Hz Offset 1000 Hz Offset 10K Hz Offset Voltage Control 0 to VCC Aging (after 30 days) 500.0KHz to150.0MHz ±5ppb to ±500ppb -40°C to 85°C max* * All stabilities not available, please consult MMD for availablity. -40°C to 95°C ±3 dBm 50Ω 10% Vdd max 90% Vdd min 30pF 5.0V 12.0V 85mA 70mA 550mA 335mA 8min. @ 25°C 100K Ohms typical AT or SC Cut options SC AT -125dBc Call MMD -140dBc Call MMD -145dBc Call MMD ±3ppm typ. ±10ppm typ. ±1.0ppm/yr. ±0.1ppm/yr. Environmental & Mechanical Detail Shock MIL-STD-883, Method 2002 Cond B Solderability MIL-STD-883, Method 2003 Solvent Resistance MIL-STD-202, Method 215 Vibration MIL-STD-883, Method 2007, Cond A Gross Leak Test MIL-STD-883, Method 1014, Cond C Fine Leak Test MSL MIL-STD-883, Method 1014, Cond A2 Level 1 per IPC/JEDEC J-STD 20 Marking Detail Line 1 = MXXXXX M = MMD XXXXX = Frequency in MHZ S = Internal Code YYWW = 4 Numerical Digit Date Code (Year / Week) L = Denotes RoHS Compliant Line 2 = SYYWWL Line 3 = XXXXX Internal use only May vary with lots Pin 1 Designator MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Revisions only with customer approval 07/26/11 F Pg 1 of 2 Part Number Guide Frequency MOC 1.5" SQUARE, 5 PIN Operating Temperature Frequency Stability Output H = HCMOS Z = Sinewave Package Height 1 = 12.7mm 2 = 25.4mm Supply Voltage 005 010 050 100 500 Crystal Cut 5 = +5VDC 12 = +12 VDC Blank = AT Cut S = SC Cut A = 0°C to + 50°C B = -10°C to + 60°C C = -20°C to +70°C D = -30°C to +70°C E = -30°C to +80°C F = -40°C to +85°C = ±5PPB = ±10PPB = ±50PPB = ±100PPB = ±500PPB Please Consult with MMD Sales Department for any other Parameters or Options Mechanical Details 38.10 [1.500] 25.40 [1.000] 19.06 [.750] 6.35 [.250] 9.53 [.375] STANDOFF 4 PLACES 5 MXX.XXX SYYWWL CCCCC 0.76 [.030] 1 6.35 [.250] 9.53 [.375] 2 38.10 [1.500] 19.06 [.750] 4 3 12.70 [.500] PIN CONNECTIONS PIN 1 OUTPUT CASE GROUND PIN 2 VOLTAGE CONTROL PIN 3 N/C PIN 4 PIN 5 SUPPLY VOLTAGE 0.65 [.025] DIMENSION IN BRACKETS ARE IN INCHES EXTERNAL BYPASS CAPACITOR IS RECOMMENDED DEVICE SHALL BE MARKED PER MMD DRAWING DO-00336 MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Revisions only with customer approval 07/26/11 F Pg 2 of 2