MOFH & MOFZ Series – 14 Pin Dip OCXO Oven Controlled Oscillator 1.0 MHz to 150.0 MHz Available SC Crystal Option RoHS Option Available ±10ppb to ±500ppb Frequency Range Frequency Stability Operating Temperature 1.0 MHz to 150.0MHz ±50ppb to ±500ppb -40°C to 85°C max* * All stabilities not available, please consult MMD for availablity. -40°C to 95°C Sinewave ±3 dBm 10% Vdd max HCMOS 3.3V, 5V 90% Vdd min Logic ‘0’= .5V max HCMOS 12V Logic ‘1’ = 4.5V min 3.3V 5V typ 220mA 200mA max 550mA 400mA 3min. @ 25°C 100K Ohms typical AT or SC Cut options SC 10 Hz Offset -100dBc 100 Hz Offset -127dBc 1000 Hz Offset -140dBc ±3ppm typ ±0.5ppm/yr. Storage Temperature Output Supply Voltage (Vdd) Supply Current Warm-up Time Input Impedance Crystal Phase Noise @ 10MHZ Voltage Control 0 to VCC Aging (after 30 days) Environmental & Mechanical Detail Shock Solderability MIL-STD-883, Method 2002 Cond B MIL-STD-883, Method 2003 Solvent Resistance MIL-STD-202, Method 215 50Ω 15pF 12V 80mA 150mA AT -92dBc -118dBc -135dBc ±10ppm typ ±1.5ppm/yr. Marking Detail Line 1 = MXXXXX M = MMD XXXXX = Frequency in MHZ = Internal Code = 4 Numerical Digit Date Code (Year / Week) = Denotes RoHS Compliant Line 2 = SYYWWL S Vibration MIL-STD-883, Method 2007, Cond A YYWW Gross Leak Test MIL-STD-883, Method 1014, Cond C L Fine Leak Test MIL-STD-883, Method 1014, Cond A2 Line 3 = XXXXX MSL Level 1 per IPC/JEDEC J-STD 20 Internal use only May vary with lots Pin 1 Designator MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Revisions only with customer approval MOF070711K Pg 1 of 2 Part Number Guide Frequency MOF 14 PIN DIP Operating Temperature Frequency Stability Output H = HCMOS Z = Sinewave Supply Voltage 3 = +3.3 VDC 5 = +5 VDC 12 = +12 VDC Crystal Cut Blank = AT Cut *S = SC Cut 050 100 250 500 = ±50PPB = ±100PPB = ±250PPB = ±500PPB A = 0°C to + 50°C B = -10°C to + 60°C C = -20°C to +70°C D = -30°C to +70°C E = -30°C to +80°C F = -40°C to +85°C Pin 1 Connection Blank = No Connection V = Voltage Control Please Consult with MMD Sales Department for any other Parameters or Options *SC Crystal must be used under specific aging and stabilities Mechanical Details 20.70 [.815] MAX MXXXXX SYYWWL XXXXX 10.80 [.425] 5.08 [.200] MIN 15.24 [.600] 8 13.10 [.516] MAX 14 7.62 [.300] 7 1 PIN CONNECTIONS PIN 1 VC OR NC PIN 7 GROUND PIN 8 OUTPUT PIN 14 SUPPLY VOLTAGE .46 [.018] PIN 1 INDICATOR LOCATED IN THIS AREA DIMENSIONS IN BRACKETS ARE IN INCHES EXTERNAL BYPASS CAPACITOR IS RECOMMENDED MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Revisions only with customer approval MOF070711K Pg 2 of 2