MPD IG136-15

IG100 Series
High Isolation
IGBT Driver
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
Input
• Operates With xx962 Drivers
• Independent Outputs
• 3,000 VAC Isolation
• Miniature SIP Case
• >3.5 MHour MTBF
• 5 Standard Models
• LOW COST!!
Parameter
Supply Voltage Range
Input Filter
Conditions
Min.
Typ.
See Model Selection Guide
Internal Capacitor
Max.
Units
Conditions
For Vin Change of 1%
IG120-12
IG120-12W
IG120-15
IG135-15
IG120-24
Max.
±1.5
200
200
150
150
300
Units
%
Output
Parameter
Line Regulation, See Note 1
Ripple & Noise (20 MHz)
Efficiency
Output Short Circuit, See Note 3
Min.
Typ.
±1.3
100
100
80
50
150
80
Continuous (Autorecovery)
mV P - P
%
General
Parameter
Isolation Voltage
Isolation Resistance
Conditions
60 Seconds
Min.
3,000
1,000
6.6
10
6.6
8.0
6.6
550
IG120-12
IG120-12W
IG120-15
IG135-15
IG120-24
Isolation Capacitance, 1 kHz/1V
Typ.
Switching Frequency
Max.
Units
VAC
M⍀
pF
10
kHz
Environmental
Parameter
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Physical
Case Size
Case Material
Weight
MicroPower Direct
Reliability Specifications
292 Page Street
Suite D
Stoughton, MA 02072
USA
Parameter
MTBF
Min.
Typ.
-40
+25
-50
Free Air Convection
RH, Non-condensing
Ambient
Max.
+85
+125
Units
ºC
ºC
95
%
0.768 x 0.386 x 0.492 Inches (19.50 x 9.80 x 12.50 mm)
Non-Conductive Black Plastic (UL94-V0)
0.195 Oz (5.5g)
Conditions
MIL HDBK 217F, 25ºC, Gnd Benign
Min.
3.5
Typ.
Max.
Units
MHours
Min.
Typ.
Max.
13
15
16
16
26
300
Units
Absolute Maximum Ratings
Parameter
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Conditions
Conditions
Max Supply Voltage (1 Sec)
Lead Temperature
IG120-12
IG120-12W
IG120-15
IG135-15
IG120-24
1.5 mm From Case For 10 Sec
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
VDC
ºC
www.micropowerdirect.com
Model Selection Guide
Input (Supply)
Model
Number
Voltage (VDC)
Nom.
Range
Output 1
Voltage (VDC)
Current
Output 2
Current
Voltage (VDC)
Output
Maximum
Load
Capacitive Fuse Rating
Slow-Blow
Current Regulation
Load
(mA)
Current
Min. Nom. Max. (mA Max) (mA, Min) Min. Nom. Max. (mA Max) (mA, Min)
(%)
(µF)
IG120-12
12
11.6 - 12.4 14.0 15.0 16.0
80.0
0.0
-7.0 -9.0 -10.0
40.0
0.0
12
470
1,000
IG120-12W
12
9.0 - 15.0
14.0 15.0 16.0
100.0
0.0
-7.0 -8.0 -9.0
80.0
0.0
12
470
1,000
IG120-15
15
14.5 - 15.5 14.0 15.0 16.0
80.0
0.0
-7.0 -8.7 -10.0
40.0
0.0
18
470
1,000
IG136-15
15
14.5 - 15.5 16.5 17.0 18.0
80.0
0.0
-7.0 -8.7 -10.0
40.0
0.0
18
470
1,000
IG120-24
24
23.3 - 24.7 14.0 15.0 16.0
80.0
0.0
-7.0 -9.0 -10.0
40.0
0.0
12
470
1,000
Typical
yp
Connection
The IG100 series is designed
to operate with the IGD962
IGBT driver.
Notes:
1. Line regulation for model IG120-12W is given for a
VIN change of 25%.
2. Load regulation is measured from 10% load to full
load. Load regulation is specified for the primary
output (output 1). Load regulation of output 2 may
vary slightly.
3. Operation at no-load will not damage these units.
However, they may not meet all specifications.
4. If output 2 is not used, it should be left open.
5. A short circuit fault that lasts over 10 minutes could
damage the unit due to an over temperature fault.
6. It is recommended that a fuse be used on the input of a
power supply for protection. See the Model Selection
table above for the correct rating.
Mechanical Dimensions
Connection Notes:
1. For model IG120-24, C1 is a 100 µF/65V.
2. Capacitors C1, C2 and C3 should be mounted as close
to the unit as possible. To ensure peak gate current,
these capacitors should have a low ESR.
3. The trace (or wire) between the DC/DC and the driver
circuit should be as short as possible.
4. The average output power of the driver circuit must
be lower than output power of the DC/DC.
Pin Connections
Pin
Function
1
2
5
6
7
+Vin
Gnd
Vout 2
Common
Vout 1
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation on the side of the unit
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]