MP5410 Low Start-up Voltage Boost Converter with Four SPDT Switches The Future of Analog IC Technology DESCRIPTION FEATURES The MP5410 is a high efficiency, current mode step-up converter with four single-pole/doublethrow (SPDT) switches designed for low-power bias supply application. The device can boost dual-cell NiCd/NiMH or single-cell Li+ battery to 10V output voltage. The MP5410 can start up from an input voltage as low as 1.8V. It uses a current limited variable frequency control algorithm to optimize efficiency and minimize external component size and cost. The internal low resistance NChannel MOSFET switch can withstand up to 10V allowing the MP5410 to produce high output voltage with high efficiency. In addition, the MP5410 can disconnect all loads from input DC power supply. The integrated schottky diode reduces external parts to save critical board space. The MP5410 features low shutdown current allowing the part to draw less than 1µA off current in shutdown mode. And it includes input under voltage and over temperature protection. The MP5410 is available in a small 16-pin QFN 3x3mm package. • • • • • • • • • • • • • 1.8V Low Voltage Start-Up 1.8V to 5.5V Input Range Output Disconnection Integrated Power MOS & Schottky Diode Variable Frequency Control <1µA Shutdown Current Current Mode Control with Internal Compensation More than 80% Efficiency at Light Load Conditions Tiny External Components Inrush Current Limiting and Internal SoftStart Input UVLO Over Temperature Protection 3x3mm QFN16 Package APPLICATIONS • • • • • • Dual-cell and Three-cell NiCd/NiMH or Single-cell Li Battery Consumer Products 3D Glass Driver Small LCD Displays Bias Supply Digital Still and Video Cameras Handheld Computers and PDAs Cell Phones For MPS green status, please visit MPS website under Quality Assurance. “MPS” and “The Future of Analog IC Technology” are Registered Trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION L1 Efficiency C OUT L 100 SW IN OUT 95 R1 90 Battery FB R2 EN MP5410 S0 Control Signal ISET RISET S1 S2 GND S3 A B C D EFFICIENCY (%) C IN 85 80 75 70 65 60 55 50 1.6 L+ MP5410 Rev.1.01 3/28/2011 L- R+ R- 2.6 3.6 4.6 5.6 VIN (V) www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. 1 MP5410—LOW START-UP VOLTAGE BOOST CONVERTER WITH FOUR SPDT SWITCHES ORDERING INFORMATION Part Number* Package Top Marking Free Air Temperature (TA) MP5410EQ QFN16 (3x3mm) ABAY -20°C to +85°C * For Tape & Reel, add suffix –Z (e.g. MP5410EQ–Z); For RoHS Compliant Packaging, add suffix –LF (e.g. MP5410EQ–LF–Z) PACKAGE REFERENCE TOP VIEW PIN 1 ID OUT SW IN GND 16 15 14 13 L 1 12 ISET EN 2 11 FB S1 3 10 S2 S0 4 9 S3 5 6 7 8 A B C D EXPOSED PAD CONNECT TO GND QFN16 (3x3mm) (4) ABSOLUTE MAXIMUM RATINGS (1) Thermal Resistance SW, OUT, A, B, C, D.....................-0.5V to +12V All other Pins ................................-0.5V to +6.5V Continuous Power Dissipation (TA = +25°C) (2) ........................................................... 2.08W Junction Temperature ...............................150°C Lead Temperature ....................................260°C Storage Temperature ............... -65°C to +150°C QFN16 (3x3mm) .................... 60 ...... 12 ... °C/W Recommended Operating Conditions (3) Supply Voltage VIN .......................... 1.8V to 5.5V Boost Converter Output Voltage .........VIN to 10V Maximum Junction Temp. (TJ) ............... +125°C MP5410 Rev.1.01 3/28/2011 θJA θJC Notes: 1) Exceeding these ratings may damage the device. 2) The maximum allowable power dissipation is a function of the maximum junction temperature TJ(MAX), the junction-toambient thermal resistance θJA, and the ambient temperature TA. The maximum allowable continuous power dissipation at any ambient temperature is calculated by PD(MAX)=(TJ(MAX)TA)/ θJA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 3) The device is not guaranteed to function outside of its operation conditions. 4) Measured on JESD51-7, 4-layer PCB. www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. 2 MP5410—LOW START-UP VOLTAGE BOOST CONVERTER WITH FOUR SPDT SWITCHES ELECTRICAL CHARACTERISTICS VIN = VEN = 2.4V, VOUT = 10V, IOUT = 2mA, TA = +25°C, unless otherwise noted. Parameters Symbol Operating Input Voltage Minimum Startup Voltage Quiescent Current Shutdown Current IN Under Voltage Lockout Under Voltage Lockout Hysteresis Step-up Converter Maximum On Time Minimum Off Time SW On-Resistance SW Leakage Current SW Current Limit Schottky Diode Forward Voltage Fixed OUT Supply Voltage VIN VST IQ NS ISD VUVLO TON TOFF RDS ON ISW LKG ISW LIMIT VFW VOUT FIXED VFB FB Input Bias Current Control Interface EN/SX Input High Voltage EN/SX Input Low Voltage EN/SX Input Bias Current SPDT Switch Switch On-Resistance Switch On-Resistance Match Between Channels Turn-on Time Turn-off Time Protection Output Disconnect Switch OnResistance IFB MP5410 Rev.1.01 3/28/2011 Min Typ Max Units 28 0.1 1.58 5.5 1.8 50 1 1.7 V V µA µA V 1.8 VOUT=0V IOUT=0, VFB=1.3V, No switching VEN=0V VIN Rising 100 FB Voltage (Regulation Mode) Thermal Shutdown Condition 4 400 ISW = 200mA VSW=12V RISET=300kΩ ON ∆RSPDT_ON TON TOFF RDISC_ON 7.5 700 0.8 2 µs ns Ω µA mA 180 IFW=100mA 0.4 0.5 0.6 V Let FB pin floating, 1.8V<VIN<5.5V Connect R-divider to FB, 1.8V<VIN<5.5V VFB = 1.23V 9.7 10 10.3 V 1.20 1.23 1.26 V 1 µA 0.4 1 V V µA 50 Ω 10 Ω VEN H VEN L IEN RSPDT 6 550 0.65 mV 1.4 VOUT=10V, IA, IB, IC, ID=2mA 25 VOUT=10V, IA, IB, IC, ID=2mA RL= 300Ω, CL= 35pF RL= 300Ω, CL= 35pF 80 170 VOUT=10V 0.7 150 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. ns ns 0.8 Ω °C 3 MP5410—LOW START-UP VOLTAGE BOOST CONVERTER WITH FOUR SPDT SWITCHES PIN FUNCTIONS Pin # Name 1 L 2 EN 3 S1 4 S0 5 6 7 8 A B C D 9 S3 10 S2 11 FB 12 ISET 13 GND 14 IN 15 SW 16 Pin Function Inductor Output Pin. L is the output node of the internal disconnecting switch. Connect the inductor to this pin. On/Off control input. A logic high input turns on the chip. A logic low input turns off the chip. This pin should not be left floating. Channel B SPDT Switch Control Input. If the chip is enabled, a logic low input switches B to GND and a logic high input switches B to OUT. This pin should not be left floating. Channel A SPDT Switch Control Input. If the chip is enabled, a logic low input switches A to GND and a logic high input switches A to OUT. This pin should not be left floating. Channel A SPDT Switch Output. Channel B SPDT Switch Output. Channel C SPDT Switch Output. Channel D SPDT Switch Output. Channel D SPDT Switch Control Input. If the chip is enabled, a logic low input switches D to GND and a logic high input switches D to OUT. This pin should not be left floating. Channel C SPDT Switch Control Input. If the chip is enabled, a logic low input switches C to GND and a logic high input switches C to OUT. This pin should not be left floating. Regulation Feedback Input. Connect to an external resistive voltage divider from the output to FB to set the boost converter output voltage. Floating this pin to achieve fixed 10V output. Constant Peak Current Set. Connect to an external resistor to GND to set the boost converter peak current. Ground. Input Supply Pin. IN pin powers the internal circuitry and is the input node of the internal disconnecting switch. Must be locally bypassed. Output Switch Node. SW is the drain node of the internal low-side N-Channel MOSFET. Connect the inductor to SW to complete the step-up converter. Step-up Converter Output. OUT Exposed Connect exposed pad to GND plane in PCB for proper thermal performance. Pad MP5410 Rev.1.01 3/28/2011 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. 4 MP5410—LOW START-UP VOLTAGE BOOST CONVERTER WITH FOUR SPDT SWITCHES TYPICAL PERFORMANCE CHARACTERISTICS VIN = VEN = 2.4V, VOUT = 10V, IOUT = 2mA, L = 10µH/150mΩ, unless otherwise noted. Efficiency VIN vs. Current Limit RISET vs. Current Limit 250 100 900 EFFICIENCY (%) 90 85 80 75 70 65 60 CURRENT LIMIT (mA) CURRENT LIMIT (mA) 95 200 150 100 50 800 700 600 500 400 300 200 100 55 50 1.6 2.6 3.6 VIN (V) MP5410 Rev.1.01 3/28/2011 4.6 5.6 0 1.6 2.6 3.6 4.6 5.6 0 0 200 400 600 800 1000 VIN (V) www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. 5 MP5410—LOW START-UP VOLTAGE BOOST CONVERTER WITH FOUR SPDT SWITCHES TYPICAL PERFORMANCE CHARACTERISTICS (continued) VIN = VEN = 2.4V, VOUT = 10V, IOUT = 2mA, L = 10µH/150mΩ, unless otherwise noted. MP5410 Rev.1.01 3/28/2011 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. 6 MP5410—LOW START-UP VOLTAGE BOOST CONVERTER WITH FOUR SPDT SWITCHES FUNCTION BLOCK DIAGRAM Figure 1—MP5410 Function Block Diagram MP5410 Rev.1.01 3/28/2011 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. 7 MP5410—LOW START-UP VOLTAGE BOOST CONVERTER WITH FOUR SPDT SWITCHES OPERATION The MP5410 is a step-up converter with four single-pole/double-throw (SPDT) switches designed for low-power bias supply application. It operates from an input voltage as low as 1.8V. The 0.65Ω internal N-Channel MOSFET power switch and low dropout voltage schottky diode are driven with a variable frequency, constant peak-current architecture for improved regulation and low operating current. Operation can be best understood by referring to the Block Diagram. Output Disconnection The MP5410 integrates disconnect switch between IN pin & L pin. The disconnect switch is composed of a NMOS and a PMOS in parallel. The MP5410 can disconnect all loads from input DC power supply when EN pin is connected to ground. Under Voltage Lockout An under voltage lockout function prevents device startup if the supply voltage on VBat is lower than approximately 1.5V. When in operation and the battery is being discharged, the device automatically enters the shutdown mode if the voltage on VIN drops below 1.5V. System Start-Up When the MP5410 is enabled, the PMOS of disconnect switch is turned on first, and then the system starts boosting the step-up converter with an internal soft-start and the output voltage rises up. The NMOS of disconnect switch is driven by Vout. It will be turned on once the output voltage reaches the threshold level. The on-resistance of NMOS is smaller than that of PMOS, so the PMOS is shorted by NOMS at normal operation to reduce the conduction loss. It is recommended on the start up sequence that the enable signal comes after input voltage established. Soft-Start The MP5410 provides soft-start by charging an internal capacitor with a very weak current source. The voltage on this capacitor, in turn, slowly ramps the peak inductor current limit from zero to the setting value. The MP5410 limits this inrush current by increasing the current limit in two steps, starting from ILIM/4 for 256 switching cycles to ILIM/2 for the next 256 cycles, and then full current limit. The soft-start time varies greatly with load current; output voltage and input voltage. Variable Frequency Constant-Peak-Current Operation When the power MOSFET is turned on the inductor current increases until the current limit is reached. The Power MOSFET is then turned off for a setting minimum off time. At the end of this minimum of time transition if the feedback pin is still lower than the 1.23V internal reference the power MOSFET will again be turned on, otherwise the MP5410 waits until the voltage drops below the threshold before turning on the MOSFET again. This process allows for optimal use of the inductor, while minimizing the output ripple and size of the output capacitor and maintaining low operating current. Integrated Schottky Diode The high switching frequency demands a highspeed rectification for optimum efficiency The MP5410 integrates a low voltage-drop schottky diode to reduce external parts to save critical board space. Four SPDT Switches The MP5410 includes four SPDT analog switches. S0~S1 control the switches respectively. If the chip is enabled, a logic low input switches the relative channel output to GND and a logic high input switches it to OUT. Soft-start and inrush current limiting are provided during start-up as well as normal mode operation. MP5410 Rev.1.01 3/28/2011 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. 8 MP5410—LOW START-UP VOLTAGE BOOST CONVERTER WITH FOUR SPDT SWITCHES Table 1—Switching Selection Control Logic EN Control Input S0 S1 S2 S3 A B C D L X X X X Open Open Open Open H L L L L GND GND GND GND H H L L L OUT GND GND GND H L H L L GND OUT GND GND H H H L L OUT OUT GND GND H L L H L GND GND OUT GND H H L H L OUT GND OUT GND H L H H L GND OUT OUT GND H H H H L OUT OUT OUT GND H L L L H GND GND GND OUT H H L L H OUT GND GND OUT H L H L H GND OUT GND OUT H H H L H OUT OUT GND OUT H L L H H GND GND OUT OUT H H L H H OUT GND OUT OUT H L H H H GND OUT OUT OUT H H H H H OUT OUT OUT OUT H: High Level MP5410 Rev.1.01 3/28/2011 Switch Output L: Low Level X: Don’t Care www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. 9 MP5410—LOW START-UP VOLTAGE BOOST CONVERTER WITH FOUR SPDT SWITCHES APPLICATION INFORMATION Components referenced below apply to Typical Application Circuit on page 11. Setting the SW Current Limit The resistor on ISET pin is used to set the SW current limit. The relationship of the SW current limit vs. the ISET resistor is showed as the curve in page 5. For Constant-Peak-Current Operation, when the power MOSFET is turned on the inductor current increases until the current limit is reached. Since the response delay, the actual SW peak current value exceeds the setting current limit a little. Under the higher input voltage and with the lower inductor, the actual SW peak current is higher due to the faster SW current di/dt. Under same condition, a lower current limit allows lower SW current and higher switching frequency, while a higher current limit allows higher SW current and lower switching frequency. Setting the Output Voltage MP5410 features internal resistive voltage divider, so floating the FB pin to achieve fixed about 10V output. Connect to an external resistive voltage divider from the output to FB to set the boost converter output voltage. Set the output voltage by selecting the resistive voltage divider ratio by the equation: VOUT = VFB × R1 + R2 R2 Where, VOUT is the output voltage, VFB = 1.23V. For R1=178kΩ and R2 = 24.9kΩ, then VOUT = 10V. Selecting the Input Capacitor The input capacitor reduces the surge current drawn from the input supply and the switching noise from the device. The input capacitor impedance at the switching frequency should be less than the input source impedance to prevent high frequency switching current from passing through the input. Ceramic capacitors with X5R or X7R dielectrics are highly recommended because of their low ESR and small temperature coefficients. For most applications, a 4.7µF or 10µF capacitor is sufficient. Selecting the Output Capacitor The output capacitor keeps the output voltage ripple small and ensures feedback loop stability. The output capacitor impedance should be low at the switching frequency. Ceramic capacitors with X7R dielectrics are recommended for their low ESR characteristics. For most applications, a less than 10µF ceramic capacitor is sufficient. Layout Considerations Careful attention must be paid to the PCB board layout and components placement. Proper layout of the high frequency switching path is critical to prevent noise and electromagnetic interference problems. The loop of MP5410 SW to GND pin, SW to OUT pin, and output capacitor is flowing with high frequency pulse current. It must be as short as possible. The IN pin is the power supply input for the internal MOSFET switch gate driver and the internal control circuitry. It must be locally bypassed. See the MP5410 demo board layout for reference. Selecting the Inductor A inductor with a DC current rating of at least 40% higher than the maximum input current is recommended for most applications at wide input range. For highest efficiency, the inductor’s DC resistance should be as small as possible. MP5410 Rev.1.01 3/28/2011 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. 10 MP5410—LOW START-UP VOLTAGE BOOST CONVERTER WITH FOUR SPDT SWITCHES TYPICAL APPLICATION CIRCUIT Figure 2—Battery Powered, VOUT=10V, 3D Glass Driver MP5410 Rev.1.01 3/28/2011 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. 11 MP5410—LOW START-UP VOLTAGE BOOST CONVERTER WITH FOUR SPDT SWITCHES PACKAGE INFORMATION QFN16 (3x3mm) 2.90 3.10 0.30 0.50 PIN 1 ID MARKING 0.18 0.30 2.90 3.10 PIN 1 ID INDEX AREA 1.50 1.80 13 16 12 PIN 1 ID SEE DETAIL A 1 1.50 1.80 0.50 BSC 4 9 8 TOP VIEW 5 BOTTOM VIEW PIN 1 ID OPTION A 0.30x45º TYP. PIN 1 ID OPTION B R0.20 TYP. 0.80 1.00 0.20 REF 0.00 0.05 DETAIL A SIDE VIEW 2.90 1.70 0.70 0.25 NOTE: 1) ALL DIMENSIONS ARE IN MILLIMETERS. 2) EXPOSED PADDLE SIZE DOES NOT INCLUDE MOLD FLASH. 3) LEAD COPLANARITY SHALL BE0.10 MILLIMETER MAX. 4) DRAWING CONFORMS TO JEDEC MO-220, VARIATION VEED-4. 5) DRAWING IS NOT TO SCALE. 0.50 RECOMMENDED LAND PATTERN NOTICE: The information in this document is subject to change without notice. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MP5410 Rev. 1.01 3/28/2011 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. 12