7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For RG213, RG214, RG8, RG9, RG225, RG393 TECHNICAL DATA SHEET PE44280 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For RG213, RG214, RG8, RG9, RG225, RG393 Configuration Connector Connector Interface Type Cable Attachment Method (Shield/Contact) Body Style 7/16 DIN Male RG213,RG214,RG8,RG9,RG225,RG393 Clamp/Solder Right Angle Electrical Specifications Impedance, Ohms 50 Mechanical Specifications Size Length, in [mm] Width/Dia., in [mm] Height, in [mm] 1.875 [47.63] 1.25 [32] 1.84 [46.74] Weight, lbs [g] 0.385 [174.63] Connector Type Contact Material and Plating Coupling Nut Material and Plating Hex Size, in Torque, in-lbs [Nm] Body Material and Plating Dielectric Type 7/16 DIN Male Silver Brass, Nickel 1 1/4 18 [2.03] Brass, Nickel PTFE . Compliance Certifications (visit www.Pasternack.com for current document) RoHS Compliant Yes Plotted and Other Data Notes: Values at 25 °C, sea level Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For RG213, RG214, RG8, RG9, RG225, RG393 PE44280 PE44280 REV 1 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For RG213, RG214, RG8, RG9, RG225, RG393 TECHNICAL DATA SHEET PE44280 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For RG213, RG214, RG8, RG9, RG225, RG393 from Pasternack Enterprises has same day shipment for domestic and International orders. Our RF, microwave and fiber optic products maintain a 99% availability and are part of the broadest selection in the industry. Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For RG213, RG214, RG8, RG9, RG225, RG393 PE44280 URL: http://www.pasternack.com/7-16-male-standard-rg213-rg214-rg8-rg9-rg225-rg393-connector-pe44280-p.aspx PE44280 REV 2 © 2013 Pasternack Enterprises All Rights Reserved 2. FORM BRAID OVER CLAMP NUT (4).TRIM BRAID BACK TO SHOULDER. CUT DIELECTRIC & CENTER CONDUCTOR TO DIMENSION SHOWN. DO NOT NICK CENTER CONDUCTOR. TIN CENTER CONDUCTOR SLIDE ASSEMBLY INTO BODY, SOLDER CENTER CONDUCTOR IN PLACE, TIGHTEN CLAMP NUT & SCREW CAP 1. SLIDE CLAMP NUT (1), WASHER (2) & GASKET (3) OVER CABLE. STRIP CABLE AS SHOWN IN A. DO NOT NICK BRAID WHILE CUTTING JACKET. TAPER END OF BRAID TO PERMIT ASSEMBLY OF BRAID CLAMP (4). SLIDE BRAID CLAMP (4) OVER BRAID & SEAT AGAINST CABLE. CUT BRAID TO DIMENSION SHOWN IN B. ASSEMBLY PROCEDURES PE44280 REV REV. - CAD FILE 012004 SCALE N/A SIZE A 127 NOTES: 1. UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE NOMINAL. 2. ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE AT ANY TIME. 3. DIMENSIONS ARE IN INCHES [mm]. 4. FITS MIL-C-17 AND EQUIVALENT CABLES. FSCM NO. 53919 PE44280 DWG TITLE 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For RG213, RG214, RG8, RG9, RG225, RG393 PE44280 CAD Drawing 3