TNC Male Connector Clamp/Solder Attachment For RG59, RG62 TECHNICAL DATA SHEET PE4154 TNC Male Connector Clamp/Solder Attachment For RG59, RG62 Configuration Connector Connector Specification Connector Interface Type Cable Attachment Method (Shield/Contact) Body Style Electrical Specifications Frequency Range, GHz Impedance, Ohms Maximum Operating Voltage, Volts Dielectric Withstanding Voltage, Vrms TNC Male MIL-STD-348A RG59,RG62 Clamp/Solder Straight DC to 11 50 500 1,500 Mechanical Specifications Temperature Operating Range, deg C -65 to +165 Size Length, in [mm] Width/Dia., in [mm] 1.05 [26.67] 0.591 [15.01] Weight, lbs [g] 0.041 [18.6] Connector Type Contact Material and Plating Contact Plating Specification Coupling Nut Material and Plating Coupling Nut Plating Specification Body Material and Plating Body Plating Specification Dielectric Type TNC Male Brass, Gold 30µ in. minimum Brass, Nickel 100µ in. minimum Brass, Nickel 100µ in. minimum Teflon . Compliance Certifications (visit www.Pasternack.com for current document) RoHS Compliant Yes Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: TNC Male Connector Clamp/Solder Attachment For RG59, RG62 PE4154 PE4154 REV 01 1 TNC Male Connector Clamp/Solder Attachment For RG59, RG62 TECHNICAL DATA SHEET PE4154 Plotted and Other Data Notes: Values at 25 °C, sea level TNC Male Connector Clamp/Solder Attachment For RG59, RG62 from Pasternack Enterprises has same day shipment for domestic and International orders. Our RF, microwave and fiber optic products maintain a 99% availability and are part of the broadest selection in the industry. Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: TNC Male Connector Clamp/Solder Attachment For RG59, RG62 PE4154 URL: http://www.pasternack.com/tnc-male-standard-rg59-rg62-connector-pe4154-p.aspx PE4154 REV 01 2 © 2013 Pasternack Enterprises All Rights Reserved PE4154 REV 01 FORM BRAID OVER CLAMP NUT (4). TRIM BRAID BACK TO SHOULDER. CUT DIELECTRIC & CENTER CONDUCTOR TO DIMENSION SHOWN. DO NOT NICK CENTER CONDUCTOR. SOLDER CONTACT TO CENTER CONDUCTOR. REMOVE EXCESS SOLDER. DO NOT OVER HEAT DIELECTRIC. INSERT CABLE ASSEMBLY INTO BODY & TIGHTEN. 2. NOTE: RG62 USES PTFE INSERT. INSERT PTFE BEFORE CONTACT. TAPER END FIRST. SLIDE CLAMP NUT (1), WASHER (2) & GASKET (3) OVER CABLE. STRIP CABLE AS SHOWN. DO NOT NICK BRAID WHILE CUTTING JACKET. TAPER END OF BRAID TO PERMIT ASSEMBLY OF BRAID CLAMP (4). SLIDE BRAID CLAMP (4) OVER BRAID & SEAT AGAINST CABLE. 1. ASSEMBLY PROCEDURES FSCM NO. 53919 PE4154 DWG TITLE CAD FILE 040413-A SCALE N/A SIZE A 2233 NOTES: 1. UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE NOMINAL. 2. ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE AT ANY TIME. 3. DIMENSIONS ARE IN INCHES [mm]. 4. FITS MIL-C-17 AND EQUIVALENT CABLES. TNC Male Connector Clamp/Solder Attachment For RG59, RG62 PE4154 CAD Drawing 3