PASTERNACK PE4383

BNC Male Connector Clamp/Solder Attachment
For PE-B150, RG180, RG195
TECHNICAL DATA SHEET
PE4383
BNC Male Connector Clamp/Solder Attachment For PE-B150, RG180, RG195
Configuration
Connector
Connector Specification
Connector Interface Type
Cable Attachment Method (Shield/Contact)
Body Style
BNC Male
MIL-C-39012
PE-B150,RG180,RG195
Clamp/Solder
Straight
Electrical Specifications
Frequency Range, GHz
Impedance, Ohms
Maximum Operating Voltage, Volts
Dielectric Withstanding Voltage, Vrms
DC to 4
50
500
1,500
Mechanical Specifications
Temperature
Operating Range, deg C
-65 to +165
Size
Length, in [mm]
Width/Dia., in [mm]
1.07 [27.18]
0.57 [14.48]
Weight, lbs [g]
0.041 [18.6]
Connector
Type
Contact Material and Plating Contact Plating Specification
Coupling Nut Material and Plating
Body Material and Plating
Dielectric Type BNC Male
Gold
MIL-G-45204
Brass, Nickel
Brass, Nickel
Teflon
.
Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price,
inventory and certifications: BNC Male Connector Clamp/Solder Attachment For PE-B150, RG180, RG195 PE4383
PE4383 REV
1
BNC Male Connector Clamp/Solder Attachment
For PE-B150, RG180, RG195
TECHNICAL DATA SHEET
PE4383
Compliance Certifications (visit www.Pasternack.com for current document)
Plotted and Other Data
Notes:
Values at 25 °C, sea level
BNC Male Connector Clamp/Solder Attachment For PE-B150, RG180, RG195 from Pasternack Enterprises has same day
shipment for domestic and International orders. Our RF, microwave and fiber optic products maintain a 99% availability and
are part of the broadest selection in the industry.
Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price,
inventory and certifications: BNC Male Connector Clamp/Solder Attachment For PE-B150, RG180, RG195 PE4383
URL: http://www.pasternack.com/bnc-male-standard-pe-b150-rg180-rg195-connector-pe4383-p.aspx
PE4383 REV
2
© 2013 Pasternack Enterprises All Rights Reserved
2. FORM BRAID OVER CLAMP NUT (3). TRIM BRAID BACK TO
SHOULDER. CUT DIELECTRIC TO DIMENSION SHOWN. DO
NOT NICK CENTER CONDUCTOR. SOLDER CONTACT TO
CENTER CONDUCTOR. REMOVE EXCESS SOLDER. DO
NOT OVER HEAT DIELECTRIC. INSERT CABLE ASSEMBLY
INTO BODY & TIGHTEN.
1. SLIDE CLAMP NUT (1) & GASKET (2) OVER CABLE. STRIP
CABLE AS SHOWN. DO NOT NICK BRAID WHILE CUTTING
JACKET. TAPER END OF BRAID TO PERMIT ASSEMBLY OF
BRAID CLAMP (3) SLIDE BRAID CLAMP(3) OVER BRAID &
SEAT AGAINST JACKET.
ASSEMBLY PROCEDURES
PE4383 REV
REV. B
CAD FILE
010711
SCALE N/A
SIZE A
2233
NOTES:
1. UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE NOMINAL.
2. ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE AT ANY TIME.
3. DIMENSIONS ARE IN INCHES [mm].
4. FITS MIL-C-17 AND EQUIVALENT CABLES.
FSCM NO. 53919
PE4383
DWG TITLE
BNC Male Connector Clamp/Solder Attachment For PE-B150, RG180, RG195
PE4383 CAD Drawing
3