75 Ohm N Male Connector Clamp/Solder Attachment For RG59, RG62 TECHNICAL DATA SHEET PE4511 75 Ohm N Male Connector Clamp/Solder Attachment For RG59, RG62 Configuration Connector Connector Interface Type Cable Attachment Method (Shield/Contact) Body Style N Male RG59,RG62 Clamp/Solder Straight Electrical Specifications Frequency Range, MHz Impedance, Ohms Maximum VSWR Maximum Operating Voltage, Volts Dielectric Withstanding Voltage, Vrms DC to 1,000 75 1.3:1 1,000 2,500 Mechanical Specifications Temperature Operating Range, deg C -65 to +165 Size Length, in [mm] Width/Dia., in [mm] 1.39 [35.31] 0.8 [20] Weight, lbs [g] 0.082 [37.19] Connector Type Contact Material and Plating Contact Plating Specification Coupling Nut Material and Plating Coupling Nut Plating Specification Body Material and Plating Body Plating Specification Dielectric Type N Male Brass, Gold 30µ in. minimum Brass, Nickel 100µ in. minimum Brass, Nickel 100µ in. minimum Teflon . Compliance Certifications (visit www.Pasternack.com for current document) RoHS Compliant Yes Plotted and Other Data Notes: Values at 25 °C, sea level Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: 75 Ohm N Male Connector Clamp/Solder Attachment For RG59, RG62 PE4511 PE4511 REV 1 75 Ohm N Male Connector Clamp/Solder Attachment For RG59, RG62 TECHNICAL DATA SHEET PE4511 75 Ohm N Male Connector Clamp/Solder Attachment For RG59, RG62 from Pasternack Enterprises has same day shipment for domestic and International orders. Our RF, microwave and fiber optic products maintain a 99% availability and are part of the broadest selection in the industry. Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: 75 Ohm N Male Connector Clamp/Solder Attachment For RG59, RG62 PE4511 URL: http://www.pasternack.com/n-male-standard-rg59-rg62-connector-pe4511-p.aspx PE4511 REV 2 © 2013 Pasternack Enterprises All Rights Reserved PE4511 REV RG62 USES PTFE INSERT. INSERT PTFE BEFORE CONTACT. TAPER END FIRST. NOTE 2. FORM BRAID OVER CLAMP NUT (4). TRIM BRAID BACK TO SHOULDER. CUT DIELECTRIC & CENTER CONDUCTOR TO DIMENSION SHOWN. DO NOT NICK CENTER CONDUCTOR. SOLDER CONTACT TO CENTER CONDUCTOR. REMOVE EXCESS SOLDER. DO NOT OVER HEAT DIELECTRIC. INSERT CABLE ASSEMBLY INTO BODY & TIGHTEN. 1. SLIDE CLAMP NUT (1), WASHER (2) & GASKET (3) OVER CABLE. STRIP CABLE AS SHOWN. DO NOT NICK BRAID WHILE CUTTING JACKET. TAPER END OF BRAID TO PERMIT ASSEMBLY OF BRAID CLAMP (4). SLIDE BRAID CLAMP (4) OVER BRAID & SEAT AGAINST CABLE. ASSEMBLY PROCEDURES REV. A CAD FILE 120911 SCALE N/A SIZE A 2233 NOTES: 1. UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE NOMINAL. 2. ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE AT ANY TIME. 3. DIMENSIONS ARE IN INCHES [mm]. 4. FITS MIL-C-17 AND EQUIVALENT CABLES. FSCM NO. 53919 PE4511 DWG TITLE 75 Ohm N Male Connector Clamp/Solder Attachment For RG59, RG62 PE4511 CAD Drawing 3