WWW.PHIHONG.COM 80W Power over Ethernet Adapter High Power Single Port Injector Features Fully Compliant Detection, Disconnect and Voltage Control IEEE802.3af Diagnostic LEDs Gigabit Compatible 1 Year Warranty Applications Satellite Receiver Wireless Network Access Points LCD Displays Safety Approvals cUL/UL CE C-Tick IRAM Mechanical Characteristics Length: 203mm (8in) Width: 108mm (4.25in) Single Source 4 Pair Power Current Sharing Wide Temperature range -40 to +55˚C Full Protection OCP, OVP Broken Wire Detection Security Cameras Kiosks Computer Workstations CCC SAA Korea (PHC) Height: 63mm (2.5in) Weight: 1.93Kg Output Specifications Model DC Output Voltage POE80U-560G +56V +56V Load Regulation Min. Max. 0A 0.72A Line Load 54-57V DC under all conditions Phihong is not responsible for any error, and reserves the right to make changes without notice. Please visit our website at www.phihong.com for the most up-to-date specifications and contact information. Revision 11/17/2011 POE80U Characteristics INPUT: AC Input Voltage Range WWW.PHIHONG.COM EMC 85 to 264VAC FCC Part 15 Class B EN55022 Class B AC Input Voltage Rating Isolation Test 100 to 240VAC, 47-63Hz AC Input Current Primary to Secondary: 4242VDC for 1 minute 10mA Primary to Field Ground: 2121VDC for 1 minute Output to Field Ground: 2121VDC 2.0A (RMS) maximum for 90VAC 1.2A (RMS) maximum for 240VAC Immunity Leakage Current 3.5mA maximum @ 254VAC 60Hz AC Inrush Current 50A (RMS) maximum for 115VAC 50A (RMS) maximum for 230VAC Primary to Secondary: >10M OHM 500VDC Primary to Field Ground: >10M OHM 500VDC 80W IEEE 802.3af/at Interoperability DC Offset No data degradation with DC imbalance 18mA per min. Ripple and Regulation 100mV maximum Efficiency 75% (typical) at maximum load, and 120VAC 60Hz Hold-up Time 10mS min. 120VAC and maximum load Transient O/P Voltage Protection 60V maximum at switch on and off at any point on AC line phase ENVIRONMENTAL: Temperature -40 to +55°C -50 to +85°C UNH Interoperability report available upon request FEATURE: Detection 12.5kohm detection resistor value required to turn on full power 4 pair power. Over Voltage/Current, Short Circuit Protection Outputs equipped with short circuit protection and overload protection as per 802.3af specifications except max average pair current is 0.72A, Peak 1.4A per pair. The output can be shorted permanently without damage Indicators Green LED 1: DC Power “OK” Red LED: Fault detected Green LED 2: Power detected “CONNECT” at 80W Input Connector IEC320 inlet 3 pin Humidity Operation EN61000-4-2. Level 3 EN61000-4-3. Level 2 EN61000-4-4. Level 2 EN61000-4-5. Level 3 EN61000-4-6. Level 2 EN61000-4-11 EN61000-3-2 Insulation Resistance OUTPUT: Total Output Power Operation Non-operation ESD: RS: EFT: Surge: CS: Voltage Dips Harmonic: 5 to 90% Warranty 1 Year Dimension Diagram Unit: mm WWW.PHIHONG.COM Description of LED Functions for Gigabit Power Injector Power-up Sequence: Upon power-up, all 3 LEDs will light for 2 seconds, as part of the self-test for the internal microprocessor software. After the 2 second period, the "ON" LED will illuminate green. The DC output voltage is now available for powering a compliant load (Phihong Proprietary detetcion). Detection Sequence: Once a compliant load is attached to the output RJ45 connector, the green "CONNECT" LED will illuminate. Should the load be non-compliant then the LEDs will blink a code specific to the cause for nondetection. Detection Failure Codes: 1. Incorrect resistive signature – The green “CONNECT” and red “FAULT” LEDs will blink 3 times. 2. Incorrect capacitive signature – The green “ON” LED will blink 3 times. 3. Incorrect Voffset – The green “CONNECT” and green “ON” LEDs will blink 3 times. 4. Unstable current measurement – The green “ON” LED will blink 3 times 5. Low voltage sensed during detection (overload) – The red “FAULT” LED will blink 3 times After the LEDs blink 3 times the Power Injector will continue to try to detect a valid load. Until the correct load is applied, the LEDs will continue to blink. If there is an open circuit connected to the output RJ45 then the LEDs will not blink but the Power Injector will continue to try to detect a valid load. Fault Sequence: Should there be a fault such as an overload or short circuit then the red "FAULT" LED will illuminate. The red “FAULT” LED will illuminate for 2 seconds and then go off as the power supply tries to redetect a valid load. If there is a problem detecting the load, the LED will indicate the possible fault as per the codes in the section above.