DC-AC INVERTER UNIT PS-DA0140-01(S) (8 W SINGLE OUTPUT) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile DC to AC Inverter is developed for single lamps Displays. Optimized for Hitachi: TX14D11VM1;TX14D12VM1; TX14D14VM1BAA; TX16D11VM2; TX18D16VM1CAB; TX20D16VM2; TX23D11VM2; TX23D12VM0 APPLICABLE LCD: Lamp Voltage 1.000 Vrms Lamp Current 3.5 ~ 6.0 mArms Lamp Start Up Voltage 2.400 Vrms (Vin : 12 Vdc) FEATURES : Remote ON/OFF Current balance circuit Extra high starting Voltage Selectable output current by jumper setting (crosslist second page) RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity LxBxH 100 x 30 x 8.5 mm SM02B-BHSS-1-TB (JST) SM02(8.0)B-BHS-1-TB (JST) DIMENSIONS : -10°C ~ +60°C -20°C ~ +85°C 95 %RH max Pin 1 Pin 1 Pin 1 Unit : mm Weight :15 (g) typ. JP3 JP2 JP1 Note: Please use plastic screw in case of a non-insulating mounting base! ORDER KEY : With order of this Inverter please give the following key. -1: for SM02(8.0)B-BHS-1-TB (JST) -2: for SM02B-BHSS-1-TB (JST) For example PS-DA0140-01-1 (S) Components No. 1 2 Part Description PCB Connector CN1 3 Connector CN2 Qty. 1 1 1 Material UL94V-0 (FR-4 or CEM-3) 53261-0690 SM02(8.0)B-BHS-1-TB Note t=1m m Molex or equal JST or equal 1 SM02B-BHSS-1-TB JST or equal Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstraße 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 1.0.3, 13th January 2010 DC-AC INVERTER UNIT PS-DA0140-01(S) (8 W SINGLE OUTPUT) (PRELIMINARY INFORMATION) Input side CN1: Pin No. CN 1-1 CN 1-2 CN 1-3 CN 1-4 CN 1-5 Output side CN2 Symbols Ratings Vin 10.8 ~ 13.2 Vdc Vin 10.8 ~ 13.2 Vdc Vrm t 0 ~ 0.4 = OFF / 2.5 ~ 5.0 = ON Vbr 0 ~ 5.0 Vdc GND GND CN 1-6 Pin No. CN 2-1 CN 2-2 CN 2-3 Short Output Current (± 0.5 mArms) 3.5 m Arm s Short 4.0 m Arm s Short 5.0 m Arm s Short 6.0 m Arm s JP 1 JP 2 JP 3 Vlow (GND) Crosslist: Displays - Jumper JP 1 JP 2 JP 2 JP 2 NO JP NO JP JP 3 JP 3 TX14D11VM1 TX14D12VM1 TX14D14VM1BAA TX16D11VM2 TX18D16VM1CAB TX20D16VM2 TX23D11VM2 TX23D12VM0 Output Current Select Control Jumper Symbols Ratings Vhigh 1.000 Vrm s (6.0 m Arm s ) N.C. - = JUMP (SHORT J1=Short 1-2, J2=Short 3-4, J3=Short 5-6) ELECTRICAL CHARACTERISTICS : (for 6mArms selection) Conditions Parameters Symbols Output Current Output Current Input Current Frequency Open Circuit Voltage No Load Shotdown Iout Iout Iin F Vopen Tsd Note 1 : Note 2: Note 3: Specification Vin (V) Vbr (V) Tu (°C) Min. Typ. Max. 12±1.2 12±0.6 12±1.2 12±1.2 11.4 12±1.2 0.0 5.0 0.0 0.0 0.0 0.0 -10 ~ +60 -10 ~ +60 -10 ~ +60 -10 ~ +60 -10 ~ +60 -10 ~ +60 5.5 50 2.200 1.0 6.0 20 0.67 60 2.400 - 6.5 0.75 70 2.700 - Unit Note mArms % Adc kHz Vrms sec Duty 100% without load Please keep minimum of 2mm clearance (all directions) between inverter high voltage area as marked on mechanical drawing and any conductors. Open circuit on all lamps for more than 3 sec., will shut the inverter down. Before apply any control signal into inverter, please provide Vcc first. Please follow the reversed sequence during power off. Power off control signal first, then power off Vcc. TEST CIRCUIT : F Vin 10.8 ~ 13.2 Vdc A 1000:1 PROBE F SW 1 V ~ Vopen Iin CN1-1 CN2-1 a V Operation b Non operation SW3 V CN1-2 Vrmt 0.4 / 2.5 Vdc Operation of unit a b SW1 CN1-3 T1 CL1 RL1 N.C. CN2-2 A ~ CN1-4 Vbr 0 ~ 5 Vdc CN1-5 CN2-3 Iout1 SW4 CN1-6 Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstraße 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 1.0.3, 13th January 2010