SF2186E • Surface Mount 3.0 x 3.0 mm Package • Complies with Directive 2002/95/EC (RoHS) Pb 1268.52 MHz SAW Filter Absolute Maximum Ratings Rating Value Units 10 dBm Input Power Level 3 V Operating Temperature Range DC Voltage on any Non-ground Terminal -40 to +85 °C Storage Temperature Range in Tape and Reel -40 to +85 °C Suitable for Lead-free Soldering - Maximum Soldering Profile 260°C for 30 s SM3030-6 Electrical Characteristics Characteristic Sym Center Frequency fC Notes Min 1268.52 Typ Insertion Loss, 1258.29 to 1278.75 MHz IL 1.7 3.2 0.5 1.8 Amplitude Ripple, 1258.29 to 1278.75 MHz 2 dB Bandwidth 20.46 38.3 1227.52 MHz 39 45.5 1309.52 MHz 50 67 Max Units MHz dB MHz Attenuation, Referenced from Minimum IL: Input/Output VSWR, 1258.29 to 1278.75 MHz 1.3 Source Impedance ZS 50 Load Impedance ZL 50 Case Style 2.1 Ω SM3030-6 3.0 x 3.0 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator Standard Reel Quantity dB 874, YWWS Reel Size 7 Inch 500 Pieces/Reel Reel Size 13 Inch 3000 Pieces/Reel Electrical Connections Connection Terminals Input 2 Output 5 Case Ground 5 0 o h m 2 All others 5 . & $ - 5 5 0 o h m 1 , 3 , 4 , 6 CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. 5. 6. 7. 8. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 1 of 5 SF2186E - 4/21/10 SF2186E Amplitude Response, 100 MHz Sweep SF2186E Amplitude Response, 300 MHz Sweep www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 2 of 5 SF2186E - 4/21/10 SF2186E Input VSWR, 100 MHz Sweep SF2186E Output VSWR, 100 MHz Sweep www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 3 of 5 SF2186E - 4/21/10 SM3030-6 Case 6-Terminal Ceramic Surface-Mount Case 3.0 X 3.0 mm Nominal Footprint Case and PCB Footprint Dimensions Dimension A B C D E F G H I J K L M N O K L N K N Min 2.87 2.87 1.12 0.77 2.67 1.47 0.72 1.37 0.47 1.17 mm Nom 3.00 3.00 1.25 0.90 2.80 1.60 0.85 1.50 0.60 1.30 3.20 1.70 1.05 0.81 0.38 Max 3.13 3.13 1.38 1.03 2.93 1.73 0.98 1.63 0.73 1.43 Min 0.113 0.113 0.044 0.030 0.105 0.058 0.028 0.054 0.019 0.046 Inches Nom 0.118 0.118 0.049 0.035 0.110 0.063 0.033 0.059 0.024 0.051 0.126 0.067 0.041 0.032 0.015 Max 0.123 0.123 0.054 0.040 0.115 0.068 0.038 0.064 0.029 0.056 Case Materials O Materials N M M PCB Footprint Top View Solder Pad Plating 0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel Lid Plating 2.0 to 3.0 µm Nickel Body Al2O3 Ceramic Pb Free TOP VIEW BOTTOM VIEW B 1 3 6 874 YWWS A 2 5 E 4 D www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. G C F H 6 1 5 2 4 3 I J Page 4 of 5 SF2186E - 4/21/10 Tape and Reel Specifications "B" REF. 100 REF. “B” Quantity Per Reel Inches millimeters 7 178 500 13 330 3000 See Detail "A" 13. 0 12.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions 2.0 3.35 mm Bo 3.35 mm Ko 1.40 mm Pitch 8.0 mm W 12.0 mm 4.0 PIN #1 A 1.50 1.75 0.3 ± 0.05 Ao 679 YWWS Bo B Ao 12.0 5.5 RO.3 (MAX.) B Pitch A Ko R0.5 (MAX.) 1.5 SECTION A-A SECTION B-B www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. USER DIRECTION OF FEED Page 5 of 5 SF2186E - 4/21/10