1000 WATTS POWER FACTOR CORRECTED SINGLE OUTPUT, HOT SWAP TCM-1000 Featuring: • Diode isolated output for hot swap • “Zero wire” slope program current sharing • High power density 6.5 Watt/cu. in. • Industry standard DIN connector • 0.99 typical power factor • DC power good and AC power fail signals • True remote inhibit • Monotonic turn-on and turn-off • Extended temperature operation • High efficiency 87% typical (48 V units) • Operating temperature range -20°C to +60°C STANDARD TCM SERIES MODEL OUTPUT RATING PWR OUT TCM-1000-24 TCM-1000-28 TCM-1000-48 24V @ 41.6A 28V @ 35.7A 48V @ 20.8A 1000 1000 1000 The 1000-watt TCM Series “hot swappable” power supplies deliver remarkable economy and reliability in applications that require redundancy over extended temperature ranges. These high-density, single-output supplies are available with a front panel and handle for use in sub-system racks or without handles for embedded applications. Power factor correction, OR-ing diodes, and current sharing make the TCM Series an ideal choice for communications and data processing systems utilizing distributed power or redundant power architecture. SEE TRACSK (R EM) T SYS Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com 1000 WATTS 13.27”x 4.87”x 2.49” TCM-1000 TCM-1000 5.2 lbs - 2.6 kgs Dimensions: Inches Millimeters SPECIFICATIONS: ALL MODELS INPUT AC Input: 180-264 Vac, 47-63 Hz internally fused 10 A. Power Factor: 0.99 typical at full load. Meets EN61000-3.2. Inrush: Limited by thermistor, 40 Ampere maximum (8ms), cold start. Hold Up Time: 20 ms minimum after removal of power supply at full load. Efficiency: 87% typical @ full load. AC Power Fail: Provides TTL "O" 5 ms before output voltage goes out of regulation band upon loss of AC power. OUTPUT Adjustability: User adjustable ±5% minimum. Output: 48 V @ 20.8 Amp. (1000 W max.). Line Regulation: ±0.2% Load Regulation: ±2% (Slope Program) from 0 to 100% load changes. Turn On Delay: 1 second typical. Ripple & Noise: 0.5% p-p, measured at 20 MHz bandwidth. Temperature Coefficient: 0.02% per degree C. Stability: 0.1% over 8 hours, under constant line, load and ambient. Transient Response: Output voltage returns to within 1% in less than 500 µs for a 50% load change. Peak transient does not exceed 3%. Overload Protection: Electronic current limit, 120% maximum. Overvoltage Protection: Protects load against power supply induced overvoltage. Trip point is factory set so that output voltage cannot exceed 136% of nominal. Requires AC input to be cycled to reset. Remote Inhibit: Contact closure or TTL "0" turns off output. DC Power Good: Provides a TTL "0" open collector when output is above 90% of nominal Maximum pull-up voltage 30 Vdc; maximum sink current, 10 mA. Redundancy: Built-in OR-ing diode, slope program current sharing, and DIN blade connector provide "hot swap" and "N+1" capabilities. Current sharing remains within 10% of the unit's full output rating given 0.2% initial accuracy in the output voltage setting. Current Sharing: As calibrated at factory, modules will share current within 10% of full rated load. Reverse Voltage: Protected against reverse voltage up to twice output voltage rating. (internal OR-ing diode.) ENVIRONMENTAL Thermal Protection: Shuts down power supply if overheated. Automatic recovery. Temperature Range: -20° to +60° C, full power, de-rate to 66% maximum power @ 71° C. Safety Agencies: Approved to UL1950; CSA 22.2 #950; IEC 950 and TUV EN60950, Class 1 SELV, CE 73/23/EEC//93/68/EEC (low voltage directive). Conducted RFI: Meets FCC Part 15, Subpart J, Class A; EN55022 Class B; and CISPR 22 Class B. Output Isolation: Isolated from ground 100 Vdc. Cooling: Self-cooled by internal ball-bearing fan. OPTIONS Option "R" - Rack Mount Panel: special panel that is required for rack mounting. Consult factory for other available options. AC INPUT (180-264 VAC Continuous Range) LOCATION 230 VAC Line 1 Line 2 Safety Ground Z32 D30 Z28 CONNECTOR Eurocard Connector Male DIN 41 612 Level 1- Type H DC OUTPUT FUNCTION LOCATION NOTES Output Z12 D14 Z16 D18 (+) Polarity Voltage Z4 D6 Z8 D10 (-) Polarity CONNECTOR Eurocard Connector Male DIN 41 612 Level 1- Type H STATUS AND CONTROL FUNCTION DC Power Good AC Power Fail Inhibit LOCATION Z20 D22 Z24 NOTES Reference to Common CONNECTOR Eurocard Connector Male DIN 41 612 Level 1- Type H Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com