DS25CP102 3.125 Gbps 2X2 LVDS Crosspoint Switch with Transmit Pre-Emphasis and Receive Equalization General Description Features The DS25CP102 is a 3.125 Gbps 2x2 LVDS crosspoint switch optimized for high-speed signal routing and switching over lossy FR-4 printed circuit board backplanes and balanced cables. Fully differential signal paths ensure exceptional signal integrity and noise immunity. The non-blocking architecture allows connections of any input to any output or outputs. The DS25CP102 features two levels (Off and On) of transmit pre-emphasis (PE) and two levels (Off and On) of receive equalization (EQ). Wide input common mode range allows the switch to accept signals with LVDS, CML and LVPECL levels; the output levels are LVDS. A very small package footprint requires a minimal space on the board while the flow-through pinout allows easy board layout. Each differential input and output is internally terminated with a 100Ω resistor to lower device insertion and return losses, reduce component count and further minimize board space. ■ DC - 3.125 Gbps low jitter, low skew, low power operation ■ Pin configurable, fully differential, non-blocking architecture ■ Pin selectable transmit pre-emphasis and receive equalization eliminate data dependant jitter ■ Wide Input Common Mode Voltage Range allows DCcoupled interface to CML and LVPECL drivers ■ On-chip 100Ω input and output termination minimizes insertion and return losses, reduces component count and minimizes board space ■ 8 kV ESD on LVDS I/O pins protects adjoining components ■ Small 4 mm x 4 mm LLP-16 space saving package Applications ■ ■ ■ ■ High-speed channel select applications Clock and data buffering and muxing OC-48 / STM-16 SD/HD/3GHD SDI Routers Typical Application 30008003 © 2008 National Semiconductor Corporation 300080 www.national.com DS25CP102 3.125 Gbps 2X2 LVDS Crosspoint Switch with Pre-Emphasis and Equalization January 17, 2008 DS25CP102 Ordering Code NSID Function DS25CP102TSQ Crosspoint Switch Block Diagram Available Equalization Levels Available Pre-Emphasis Levels Off / On Off / On Connection Diagram 30008001 30008002 Pin Descriptions Pin Name Pin Number I/O, Type Pin Description IN0+, IN0- , IN1+, IN1- 1, 2, 3, 4 I, LVDS Inverting and non-inverting high speed LVDS input pins. OUT0+, OUT0-, OUT1+, OUT1- 12, 11, 10, 9 O, LVDS Inverting and non-inverting high speed LVDS output pins. SEL0, SEL1 7, 8 I, LVCMOS Switch configuration pins. There is a 20k pulldown resistor on this pin. EN0, EN1 14, 13 I, LVCMOS Output enable pins. There is a 20k pulldown resistor on this pin. PE 15 I, LVCMOS Transmit Pre-Emphasis select pin. There is a 20k pulldown resistor on this pin. EQ 6 I, LVCMOS Receive Equalizaton select pin. There is a 20k pulldown resistor on this pin. VDD 16 Power Power supply pin. GND 5, DAP Power Ground pin and Device Attach Pad (DAP) ground. www.national.com 2 θJA If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. +41.8°C/W θJC ESD Susceptibility HBM (Note 1) Supply Voltage −0.3V to +4V LVCMOS Input Voltage −0.3V to (VCC + 0.3V) LVDS Input Voltage −0.3V to +4V LVDS Differential Input Voltage 0V to 1.0V LVDS Output Voltage −0.3V to (VCC + 0.3V) LVDS Differential Output Voltage 0V to 1.0V LVDS Output Short Circuit Current 5 ms Duration Junction Temperature +150°C Storage Temperature Range −65°C to +150°C Lead Temperature Range Soldering (4 sec.) +260°C Maximum Package Power Dissipation at 25°C SQA Package 2.99W Derate SQA Package 23.9 mW/°C above +25°C +6.9°C/W ≥8 kV ≥250V ≥1250V MM (Note 2) CDM (Note 3) Note 1: Human Body Model, applicable std. JESD22-A114C Note 2: Machine Model, applicable std. JESD22-A115-A Note 3: Field Induced Charge Device Model, applicable std. JESD22-C101-C Recommended Operating Conditions Supply Voltage (VCC) Receiver Differential Input Voltage (VID) Operating Free Air Temperature (TA) Min 3.0 0 Typ 3.3 Max 3.6 1 Units V V −40 +25 +85 °C DC Electrical Characteristics (Notes 5, 6, 7) Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units VCC V LVCMOS DC SPECIFICATIONS VIH High Level Input Voltage 2.0 VIL Low Level Input Voltage IIH High Level Input Current VIN = 3.6V VCC = 3.6V IIL Low Level Input Current VIN = GND VCC = 3.6V VCL Input Clamp Voltage ICL = −18 mA, VCC = 0V GND 40 0.8 V 175 250 μA 0 ±10 μA −0.9 −1.5 V 1 V +100 mV LVDS INPUT DC SPECIFICATIONS VID Input Differential Voltage 0 VTH Differential Input High Threshold VTL Differential Input Low Threshold VCMR Common Mode Voltage Range VID = 100 mV IIN Input Current VIN = +3.6V or 0V VCC = 3.6V or 0V CIN Input Capacitance Any LVDS Input Pin to GND 1.7 pF RIN Input Termination Resistor Between IN+ and IN- 100 Ω VCM = +0.05V or VCC-0.05V 0 −100 3 0 0.05 ±1 mV VCC 0.05 V ±10 μA www.national.com DS25CP102 Package Thermal Resistance Absolute Maximum Ratings (Note 4) DS25CP102 Symbol Parameter Conditions Min Typ Max Units 250 350 450 mV 35 mV 1.375 V 35 mV LVDS OUTPUT DC SPECIFICATIONS VOD Differential Output Voltage ΔVOD Change in Magnitude of VOD for Complimentary Output States VOS Offset Voltage ΔVOS Change in Magnitude of VOS for Complimentary Output States RL = 100Ω IOS Output Short Circuit Current (Note 8) OUT to GND -35 -55 mA OUT to VCC 7 55 mA RL = 100Ω -35 1.05 1.2 -35 COUT Output Capacitance Any LVDS Output Pin to GND 1.2 pF ROUT Output Termination Resistor Between OUT+ and OUT- 100 Ω SUPPLY CURRENT ICC Supply Current PE = OFF, EQ = OFF 77 90 mA ICCZ Supply Current with Outputs Disabled EN0 = EN1 = 0 23 29 mA Note 4: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. Note 5: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed. Note 6: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except VOD and ΔVOD. Note 7: Typical values represent most likely parametric norms for VCC = +3.3V and TA = +25°C, and at the Recommended Operation Conditions at the time of product characterization and are not guaranteed. Note 8: Output short circuit current (IOS) is specified as magnitude only, minus sign indicates direction only. www.national.com 4 (Note 11) Over recommended operating supply and temperature ranges unless otherwise specified. (Notes 9, 10) Symbol Parameter Conditions Min Typ Max Units 365 500 ps 345 500 ps LVDS OUTPUT AC SPECIFICATIONS tPLHD Differential Propagation Delay Low to High tPHLD Differential Propagation Delay High to Low tSKD1 Pulse Skew |tPLHD − tPHLD| (Note 12) 20 55 ps tSKD2 Channel to Channel Skew (Note 13) 12 25 ps tSKD3 Part to Part Skew , (Note 14) 50 150 ps tLHT Rise Time 65 120 ps tHLT Fall Time 65 120 ps tON Output Enable Time ENn = LH to output active 7 20 μs tOFF Output Disable Time ENn = HL to output inactive 5 12 ns tSEL Select Time SELn LH or HL to output 3.5 12 ns RL = 100Ω RL = 100Ω JITTER PERFORMANCE WITH EQ = Off, PE = Off (Figure 5) tRJ1 tRJ2 tDJ1 tDJ2 tTJ1 tTJ2 Random Jitter (RMS Value) No Test Channels (Note 15) VID = 350 mV VCM = 1.2V Clock (RZ) 2.5 Gbps 0.5 1 ps 3.125 Gbps 0.5 1 ps Deterministic Jitter (Peak to Peak) No Test Channels (Note 16) VID = 350 mV VCM = 1.2V K28.5 (NRZ) 2.5 Gbps 6 22 ps 3.125 Gbps 6 22 ps Total Jitter (Peak to Peak) No Test Channels (Note 17) VID = 350 mV VCM = 1.2V PRBS-23 (NRZ) 2.5 Gbps 0.03 0.08 UIP-P 3.125 Gbps 0.05 0.11 UIP-P JITTER PERFORMANCE WITH EQ = Off, PE = On (Figures 6, 9) tRJ1B tRJ2B tDJ1B tDJ2B tTJ1B tTJ2B Random Jitter (RMS Value) Test Channel B (Note 15) VID = 350 mV VCM = 1.2V Clock (RZ) 2.5 Gbps 0.5 1 ps 3.125 Gbps 0.5 1 ps Deterministic Jitter (Peak to Peak) Test Channel B (Note 16) VID = 350 mV VCM = 1.2V K28.5 (NRZ) 2.5 Gbps 3 12 ps 3.125 Gbps 3 12 ps Total Jitter (Peak to Peak) Test Channel B (Note 17) VID = 350 mV VCM = 1.2V PRBS-23 (NRZ) 2.5 Gbps 0.03 0.06 UIP-P 3.125 Gbps 0.04 0.09 UIP-P JITTER PERFORMANCE WITH EQ = On, PE = Off (Figures 7, 9) tRJ1D tRJ2D tDJ1D tDJ2D tTJ1D tTJ2D Random Jitter (RMS Value) Test Channel D (Note 15) VID = 350 mV VCM = 1.2V Clock (RZ) 2.5 Gbps 0.5 1 ps 3.125 Gbps 0.5 1 ps Deterministic Jitter (Peak to Peak) Test Channel D (Note 16) VID = 350 mV VCM = 1.2V K28.5 (NRZ) 2.5 Gbps 16 24 ps 3.125 Gbps 12 24 ps Total Jitter (Peak to Peak) Test Channel D (Note 17) VID = 350 mV VCM = 1.2V PRBS-23 (NRZ) 2.5 Gbps 0.07 0.11 UIP-P 3.125 Gbps 0.07 0.11 UIP-P 5 www.national.com DS25CP102 AC Electrical Characteristics DS25CP102 Symbol Parameter Conditions Min Typ Max Units JITTER PERFORMANCE WITH EQ = On, PE = On (Figures 8, 9) tRJ1BD tRJ2BD tDJ1BD tDJ2BD tTJ1BD tTJ2BD Random Jitter (RMS Value) Input Test Channel D Output Test Channel B (Note 15) VID = 350 mV VCM = 1.2V Clock (RZ) 2.5 Gbps 0.5 1 ps 3.125 Gbps 0.5 1 ps Deterministic Jitter (Peak to Peak) Input Test Channel D Output Test Channel B (Note 16) VID = 350 mV VCM = 1.2V K28.5 (NRZ) 2.5 Gbps 14 31 ps 3.125 Gbps 6 21 ps Total Jitter (Peak to Peak) Input Test Channel D Output Test Channel B (Note 17) VID = 350 mV VCM = 1.2V PRBS-23 (NRZ) 2.5 Gbps 0.08 0.15 UIP-P 3.125 Gbps 0.10 0.16 UIP-P Note 9: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed. Note 10: Typical values represent most likely parametric norms for VCC = +3.3V and TA = +25°C, and at the Recommended Operation Conditions at the time of product characterization and are not guaranteed. Note 11: Specification is guaranteed by characterization and is not tested in production. Note 12: tSKD1, |tPLHD − tPHLD|, Pulse Skew, is the magnitude difference in differential propagation delay time between the positive going edge and the negative going edge of the same channel. Note 13: tSKD2, Channel to Channel Skew, is the difference in propagation delay (tPLHD or tPHLD) among all output channels in Broadcast mode (any one input to all outputs). Note 14: tSKD3, Part to Part Skew, is defined as the difference between the minimum and maximum differential propagation delays. This specification applies to devices at the same VCC and within 5°C of each other within the operating temperature range. Note 15: Measured on a clock edge with a histogram and an acummulation of 1500 histogram hits. Input stimulus jitter is subtracted geometrically. Note 16: Tested with a combination of the 1100000101 (K28.5+ character) and 0011111010 (K28.5- character) patterns. Input stimulus jitter is subtracted algebraically. Note 17: Measured on an eye diagram with a histogram and an acummulation of 3500 histogram hits. Input stimulus jitter is subtracted. www.national.com 6 DS25CP102 DC Test Circuits 30008020 FIGURE 1. Differential Driver DC Test Circuit AC Test Circuits and Timing Diagrams 30008021 FIGURE 2. Differential Driver AC Test Circuit 30008022 FIGURE 3. Propagation Delay Timing Diagram 30008023 FIGURE 4. LVDS Output Transition Times 7 www.national.com DS25CP102 Pre-Emphasis and Equalization Test Circuits 30008029 FIGURE 5. Jitter Performance Test Circuit 30008027 FIGURE 6. Pre-Emphasis Performance Test Circuit 30008026 FIGURE 7. Equalization Performance Test Circuit www.national.com 8 DS25CP102 30008030 FIGURE 8. Pre-Emphasis and Equalization Performance Test Circuit 30008028 FIGURE 9. Test Channel Block Diagram stant of 3.7 and Loss Tangent of 0.02). The edge coupled differential striplines have the following geometries: Trace Width (W) = 5 mils, Gap (S) = 5 mils, Height (B) = 16 mils. Test Channel Loss Characteristics The test channel was fabricated with Polyclad PCL-FR-370Laminate/PCL-FRP-370 Prepreg materials (Dielectric conTest Channel Length (inches) 500 MHz 750 MHz 1000 MHz Insertion Loss (dB) 1250 MHz 1500 MHz 1560 MHz A 10 -1.2 -1.7 -2.0 -2.4 -2.7 -2.8 B 20 -2.6 -3.5 -4.1 -4.8 -5.5 -5.6 C 30 -4.3 -5.7 -7.0 -8.2 -9.4 -9.7 D 15 -1.6 -2.2 -2.7 -3.2 -3.7 -3.8 E 30 -3.4 -4.5 -5.6 -6.6 -7.7 -7.9 F 60 -7.8 -10.3 -12.4 -14.5 -16.6 -17.0 9 www.national.com DS25CP102 Functional Description The DS25CP102 is a 3.125 Gbps 2x2 LVDS digital crosspoint switch optimized for high-speed signal routing and switching over lossy FR-4 printed circuit board backplanes and balanced cables. TABLE 1. Switch Configuration Truth Table SEL1 SEL0 OUT1 OUT0 0 0 IN0 IN0 0 1 IN0 IN1 1 0 IN1 IN0 1 1 IN1 IN1 TABLE 2. Output Enable Truth Table EN1 EN0 OUT1 OUT0 0 0 Disabled Disabled 0 1 Disabled Enabled 1 0 Enabled Disabled 1 1 Enabled Enabled In addition, the DS25CP102 has a pre-emphasis control pin for switching the transmit pre-emphasis to ON and OFF setting and an equalization control pin for switching the receive equalization to ON and OFF setting. The following are the transmit pre-emphasis and receive equalization truth tables. Transmit Pre-Emphasis Truth Table OUTPUTS OUT0 and OUT1 CONTROL Pin (PE) State Pre-Emphasis Level 0 OFF 1 ON Transmit Pre-Emphasis Level Selection Receive Equalization Truth Table INPUTS IN0 and IN1 CONTROL Pin (EQ) State Equalization Level 0 OFF 1 ON Receive Equalization Level Selection www.national.com 10 The DS25CP102 accepts differential signals and allows simple AC or DC coupling. With a wide common mode range, the DS25CP102 can be DC-coupled with all common differential 30008031 Typical LVDS Driver DC-Coupled Interface to DS25CP102 Input 30008032 Typical CML Driver DC-Coupled Interface to DS25CP102 Input 30008033 Typical LVPECL Driver DC-Coupled Interface to DS25CP102 Input 11 www.national.com DS25CP102 drivers (i.e. LVPECL, LVDS, CML). The following three figures illustrate typical DC-coupled interface to common differential drivers. Note that the DS25CP102 inputs are internally terminated with a 100Ω resistor. Input Interfacing DS25CP102 and assumes that the receivers have high impedance inputs. While most differential receivers have a common mode input range that can accomodate LVDS compliant signals, it is recommended to check respective receiver's data sheet prior to implementing the suggested interface implementation. Output Interfacing The DS25CP102 outputs signals that are compliant to the LVDS standard. Its outputs can be DC-coupled to most common differential receivers. The following figure illustrates typical DC-coupled interface to common differential receivers 30008034 Typical DS25CP102 Output DC-Coupled Interface to an LVDS, CML or LVPECL Receiver www.national.com 12 DS25CP102 Typical Performance 30008050 30008052 Total Jitter as a Function of Data Rate Residual Jitter as a Function of Data Rate, FR4 Stripline Length and EQ Level 30008058 Total Jitter as a Function of Input Common Mode Voltage 30008057 Supply Current as a Function of Data Rate and PE Level 30008051 Residual Jitter as a Function of Data Rate, FR4 Stripline Length and PE Level 13 www.national.com DS25CP102 30008060 30008062 A 3.125 Gbps NRZ PRBS-7 without PE or EQ After 2" Differential FR-4 Stripline H: 50 ps / DIV, V: 100 mV / DIV A 3.125 Gbps NRZ PRBS-7 with PE After 40" Differential FR-4 Stripline H: 50 ps / DIV, V: 100 mV / DIV 30008061 A 3.125 Gbps NRZ PRBS-7 without PE or EQ After 40" Differential FR-4 Stripline H: 50 ps / DIV, V: 100 mV / DIV www.national.com 14 DS25CP102 Physical Dimensions inches (millimeters) unless otherwise noted Order Number DS25CP102TSQ NS Package Number SQA16A (See AN-1187 for PCB Design and Assembly Recommendations) 15 www.national.com DS25CP102 3.125 Gbps 2X2 LVDS Crosspoint Switch with Pre-Emphasis and Equalization Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: [email protected] German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: [email protected] National Semiconductor Japan Technical Support Center Email: [email protected]