FUJI 6MBP10VAA120-50

http://www.fujielectric.com/products/semiconductor/
6MBP10VAA120-50
IGBT Modules
IGBT MODULE (V series)
1200V / 10A / IPM
Features
• Temperature protection provided by directly detecting
the junction temperature of the IGBTs
• Low power loss and soft switching
• High performance and high reliability IGBT with overheating
protection
• Higher reliability because of a big decrease in number of
parts in built-in control circuit
Maximum Ratings and Characteristics
Absolute Maximum Ratings (TC =25ºC, VCC =15V unless otherwise specified)
Items
Symbol
Min.
Max.
Units
Collector-Emitter Voltage (*1)
Short Circuit Voltage
VCES
VSC
IC
Icp
-IC
PC
VCC
Vin
VALM
IALM
Tj
Topr
Tstg
Tsol
Viso
-
0
400
-0.5
-0.5
-0.5
-20
-40
-
1200
800
10
20
10
97
20
VCC+0.5
VCC
20
150
110
125
260
AC2500
1.7
V
V
A
A
A
W
V
V
V
mA
ºC
ºC
ºC
ºC
Vrms
Nm
Collector Current
DC
1ms
Duty=89% (*2)
1 device (*3)
Collector Power Dissipation
Supply Voltage of Pre-Driver (*4)
Input Signal Voltage (*5)
Alarm Signal Voltage (*6)
Alarm Signal Current (*7)
Junction Temperature
Operating Case Temperature
Storage Temperature
Solder Temperature (*8)
Isolating Voltage (*9)
Screw Torque
Mounting (M4)
Note *1: VCES shall be applied to the input voltage between terminal P-(U,V, W) and (U,V, W)-N.
Note *2: Duty=125ºC/Rth(j-c)D /(I F×VF Max.)×100
Note *3: PC=125ºC/Rth(j-c)Q
Note *4: VCC shall be applied to the input voltage between terminal No.3 and 1, 6 and 4, 9 and 7,11 and 10.
Note *5: Vin shall be applied to the input voltage between terminal No.2 and 1, 5 and 4, 8 and 7,12~14 and 10.
Note *6: VALM shall be applied to the voltage between terminal No.15 and 10.
Note *7: I ALM shall be applied to the input current to terminal No.15.
Note *8: Immersion time 10±1sec. 1time
Note *9: Terminal to base, 50/60Hz sine wave 1min. All terminals should be connected together during the test.
1
6MBP10VAA120-50
IGBT Modules
http://www.fujielectric.com/products/semiconductor/
Electrical Characteristics (Tj =25ºC, VCC =15V unless otherwise specified)
Items
Inverter
Collector Current at off signal input
Symbol
Conditions
ICES
VCE=1200V
Terminal
Chip
Terminal
Chip
Collector-Emitter saturation voltage
VCE(sat)
IC =10A
Forward voltage of FWD
VF
IF=10A
ton
toff
VDC =600V, Tj =125ºC, IC =10A
trr
VDC =600V, IC =10A
Switching time
Supply current of P-side pre-driver (per one unit)
Supply current of N-side pre-driver
Iccp
Iccn
Vinth(on)
Input signal threshold voltage
Vinth(off)
Over Current Protection Level
IOC
Over Current Protection Delay time
tdOC
Short Circuit Protection Delay time
tSC
IGBT Chips Over Heating Protection Temperature Level TjOH
Over Heating Protection Hysteresis
TjH
Under Voltage Protection Level
VUV
Under Voltage Protection Hysteresis
VH
tALM(OC)
tALM(UV)
Alarm Signal Hold Time
tALM(TjOH)
Resistance for current limit
RALM
Switching Frequency= 0-15kHz
TC =-20~110ºC
Vin -GND
ON
OFF
Tj =125ºC
Tj =125ºC
Tj =125ºC
Surface of IGBT Chips
ALM-GND
TC =-20~110ºC
VCC 10V
Min.
Typ.
Max.
Units
1.1
-
1.68
2.10
-
1.0
2.05
2.55
2.1
mA
V
V
V
V
µs
µs
-
-
0.3
µs
1.2
1.5
15
150
11.0
0.2
1.0
2.5
5.0
960
1.4
1.7
5
2
20
0.5
2.0
4.0
8.0
1265
8
18
1.6
1.9
3
12.5
2.4
4.9
11.0
1570
mA
mA
V
V
A
µs
µs
ºC
ºC
V
V
ms
ms
ms
Ω
Thermal Characteristics (TC = 25ºC)
Items
Junction to Case Thermal Resistance (*10)
Inverter
Symbol
Rth(j-c)Q
Rth(j-c)D
Rth(c-f)
IGBT
FWD
Case to Fin Thermal Resistance with Compound
Min.
-
Typ.
0.05
Max.
1.28
2.02
-
Units
°C/W
°C/W
°C/W
Note *10: For 1device, the measurement point of the case is just under the chip.
Noise Immunity (VDC =600V, VCC =15V)
Items
Conditions
Min.
Typ.
Max.
Units
Common mode rectangular noise
Pulse width 1μs, polarity ±, 10 min.
Judge : no over-current, no miss operating
±2.0
-
-
kV
Recommended Operating Conditions
Items
DC Bus Voltage
Power Supply Voltage of Pre-Driver
Switching frequency of IPM
Arm shoot through blocking time for IPM's input signal
Screw Torque (M4)
Symbol
VDC
VCC
fSW
tdead
-
Min.
13.5
1.0
1.3
2
Typ.
15.0
-
Max.
800
16.5
20
1.7
Units
V
V
kHz
µs
Nm
6MBP10VAA120-50
IGBT Modules
http://www.fujielectric.com/products/semiconductor/
Block Diagram
P
VccU ③
VinU ②
Pre-Driver
U
GNDU ①
VccV ⑥
VinV ⑤
Pre-Driver
V
GNDV ④
VccW ⑨
VinW ⑧
Pre-Driver
W
GNDW ⑦
Vcc ⑪
VinX ⑫
VinY ⑬
Pre-Driver
VinZ ⑭
GND ⑩
ALM ⑮
N
RALM
Pre-drivers include following functions
1. Amplifier for driver
2. Short circuit protection
3. Under voltage lockout circuit
4. Over current protection
5. IGBT chip over heating protection
3
6MBP10VAA120-50
IGBT Modules
http://www.fujielectric.com/products/semiconductor/
Characteristics (Representative)
Tj
Vinth(on), Vinth(off) [V]
IOC
TC
VCC
VCC
VCC
Vinth(off)
Vinth(on)
VCC
VCC
VCC
VUV
VH
VCC
Tj
Tj
TjOH , TjH vs. VCC (typ.)
TjOH
tALM
TjH
TjOH
tALM(TjOH)
tALM(OC)
TjH
VCC
VCC
4
6MBP10VAA120-50
IGBT Modules
http://www.fujielectric.com/products/semiconductor/
Inverter
Tj
Tj
VCC
VCC
VCC
VCC
IC
IC
VCC
VCC
VCE
VCE
Tj
Tj
VCC
VCC
VCC
VCC
IC
IC
VCC
VCC
VCE
Tj
Tj
IF
Tj
IF
Tj
VCE
VF
VF
5
6MBP10VAA120-50
Tj
VDC
Eon
VCC
Tj
Eon, Eoff, Err [mj/cycle]
VCC
Eon, Eoff, Err [mJ/cycle]
VDC
IGBT Modules
http://www.fujielectric.com/products/semiconductor/
Eon
Eoff
Eoff
Err
Err
IC
Rth(j-c) [°C/W]
Tj
IC
VCC
IC
PC
PC
VCE
TC
TC
6
6MBP10VAA120-50
VDC = 600V, VCC = 15V, Tj = 125°C
Tj
ton
ton
toff
toff
ton, toff, tf [nsec]
VCC
ton, toff, tf [nsec]
VDC
IGBT Modules
http://www.fujielectric.com/products/semiconductor/
tf
tf
IC
IC
trr, Irr vs. If VDC = 600V,
VDC VCC = 15V
VCC
VCC
trr
Irr
IOC
trr Tj
trr Tj
Irr Tj
Irr Tj
IF
Tj
Outline Drawings, mm
7
6MBP10VAA120-50
IGBT Modules
http://www.fujielectric.com/products/semiconductor/
WARNING
1.This Catalog contains the product specifications, characteristics, data, materials, and structures as of May 2011.
The contents are subject to change without notice for specification changes or other reasons. When using a product listed in this Catalog, be
sur to obtain the latest specifications.
2.All applications described in this Catalog exemplify the use of Fuji's products for your reference only. No right or license, either express or
implied, under any patent, copyright, trade secret or other intellectual property right owned by Fuji Electric Co., Ltd. is (or shall be deemed)
granted. Fuji Electric Co., Ltd. makes no representation or warranty, whether express or implied, relating to the infringement or alleged
infringement of other's intellectual property rights which may arise from the use of the applications described herein.
3.Although Fuji Electric Co., Ltd. is enhancing product quality and reliability, a small percentage of semiconductor products may become
faulty. When using Fuji Electric semiconductor products in your equipment, you are requested to take adequate safety measures to prevent
the equipment from causing a physical injury, fire, or other problem if any of the products become faulty. It is recommended to make your
design failsafe, flame retardant, and free of malfunction.
4.The products introduced in this Catalog are intended for use in the following electronic and electrical equipment which has normal reliability
requirements.
• Computers
• OA equipment
• Communications equipment (terminal devices)
• Measurement equipment
• Machine tools
• Audiovisual equipment • Electrical home appliances
• Personal equipment • Industrial robots etc.
5.If you need to use a product in this Catalog for equipment requiring higher reliability than normal, such as for the equipment listed below,
it is imperative to contact Fuji Electric Co., Ltd. to obtain prior approval. When using these products for such equipment, take adequate
measures such as a backup system to prevent the equipment from malfunctioning even if a Fuji's product incorporated in the equipment
becomes faulty.
• Transportation equipment (mounted on cars and ships)
• Trunk communications equipment
• Traffic-signal control equipment
• Gas leakage detectors with an auto-shut-off feature
• Emergency equipment for responding to disasters and anti-burglary devices
• Safety devices
• Medical equipment
6.Do not use products in this Catalog for the equipment requiring strict reliability such as the following and equivalents to strategic equipment
(without limitation).
• Space equipment
• Aeronautic equipment
• Nuclear control equipment
• Submarine repeater equipment
7.Copyright ©1996-2011 by Fuji Electric Co., Ltd. All rights reserved.
No part of this Catalog may be reproduced in any form or by any means without the express permission of Fuji Electric Co., Ltd.
8.If you have any question about any portion in this Catalog, ask Fuji Electric Co., Ltd. or its sales agents before using the product.
Neither Fuji Electric Co., Ltd. nor its agents shall be liable for any injury caused by any use of the products not in accordance with instructions
set forth herein.
8