Board 1 SKYPER 32PRO R Absolute Maximum Ratings Symbol SKYPER® Values Unit Vs Supply voltage primary 16 V IoutPEAK Output peak current 15 A IoutAVmax Output average current 50 mA fmax max. switching frequency 50 kHz VCE Collector emitter voltage sense across the IGBT 1700 V 4000 V 1500 V 1500 V 1.5 " 1.5 " Visol IO VisolPD Adaptor board Visol12 Board 1 SKYPER 32PRO R Conditions Isolation test voltage input - output (AC, rms, 2s) Partial discharge extinction voltage, rms, QPD ! 10pC Isolation test voltage output 1 - output 2 (AC, rms, 2s) RGon min RGoff min Minimum rating for external RGoff Top Operating temperature -25 ... 85 °C Features Tstg Storage temperature -25 ... 85 °C • Two output channels • Failure management Characteristics Preliminary Data Symbol Conditions min. typ. max. Unit • Adaptor board for SKYPER 32 IGBT drivers in bridge circuits for industrial applications • DC bus up to 1200V Vs Supply voltage primary side 14.4 15 15.6 V Vj input signal voltage on / off VIT+ Input treshold voltage HIGH VIT- Input threshold voltage (LOW) Footnotes VG(on) Turn on gate voltage output All characteristics listed in the data sheet are guilty for the use with SKYPER 32 Please consider the derating of the ambient temperature Please refer to the datasheet of SKYPER 32 for further information VG(off) Turn off gate voltage output -7 V td(on)IO Input-output turn-on propagation time 1.2 µs td(off)IO Input-output turn-off propagation time 1.2 µs Typical Applications* 15 / 0 V 12.3 4.6 V V 15 V Derating This is an electrostatic discharge sensitive device (ESDS), international standard IEC 60747-1, Chapter IX * The specifications of our components may not be considered as an assurance of component characteristics. Components have to be tested for the respective application. Adjustments may be necessary. The use of SEMIKRON products in life support appliances and systems is subject to prior specification and written approval by SEMIKRON. We therefore strongly recommend prior consultation of our personal. Adaptor board © by SEMIKRON Rev. 02 – 21.04.2010 1 Board 1 SKYPER® 32PRO R - Technical Explanations Adaptor Board 1 SKYPER® 32PRO R Technical Explanations Revision 02 -----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------This Technical Explanation is valid for the following parts: part number L6100231 type Board 1 SKYPER® 32PRO R date code (YYWW) ≥ 1004 Related documents: title Technical Explanations SKYPER® 32PRO R Prepared by: Johannes Krapp ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ Content Application and Handling Instructions .................................................................................................................... 3 Further application support ..................................................................................................................................... 3 General Description ................................................................................................................................................ 3 Dimensions ............................................................................................................................................................. 4 Component Placement Layout ............................................................................................................................... 4 ® PIN Array (not SKiiP compatible).......................................................................................................................... 5 PIN Array – Secondary Side................................................................................................................................... 6 Signal IF_CMN_nHALT .......................................................................................................................................... 7 Setting Dead Time .................................................................................................................................................. 7 Setting Dynamic Short Circuit Protection ............................................................................................................... 7 Collector Series Resistance.................................................................................................................................... 8 Adaptation Gate Resistors...................................................................................................................................... 8 Setting Soft Turn-Off............................................................................................................................................... 8 Over Temperature Protection Circuit (OTP) ........................................................................................................... 9 Mounting Notes....................................................................................................................................................... 9 Schematics ........................................................................................................................................................... 10 Parts List ............................................................................................................................................................... 12 2 Rev. 02 – 21.04.2010 © by SEMIKRON Board 1 SKYPER® 32PRO R - Technical Explanations Please note: All values in this technical explanation are typical values. Typical values are the average values expected in large quantities and are provided for information purposes only. These values can and do vary in different applications. All operating parameters should be validated by user’s technical experts for each application. Application and Handling Instructions Please provide for static discharge protection during handling. As long as the hybrid driver is not completely assembled, the input terminals have to be short-circuited. Persons working with devices have to wear a grounded bracelet. Any synthetic floor coverings must not be statically chargeable. Even during transportation the input terminals have to be short-circuited using, for example, conductive rubber. Worktables have to be grounded. The same safety requirements apply to MOSFET- and IGBT-modules. Any parasitic inductances within the DC-link have to be minimised. Over-voltages may be absorbed by C- or RCDsnubber networks between main terminals for PLUS and MINUS of the power module. When first operating a newly developed circuit, SEMIKRON recommends to apply low collector voltage and load current in the beginning and to increase these values gradually, observing the turn-off behaviour of the free-wheeling diode and the turn-off voltage spikes generated across the IGBT. An oscillographic control will be necessary. Additionally, the case temperature of the module has to be monitored. When the circuit works correctly under rated operation conditions, short-circuit testing may be done, starting again with low collector voltage. It is important to feed any errors back to the control circuit and to switch off the device immediately in failure events. Repeated turn-on of the IGBT into a short circuit with a high frequency may destroy the device. The inputs of the hybrid driver are sensitive to over-voltage. Voltages higher than VS +0,3V or below -0,3V may destroy these inputs. Therefore, control signal over-voltages exceeding the above values have to be avoided. The connecting leads between hybrid driver and the power module should be as short as possible (max. 20cm), the driver leads should be twisted. Further application support Latest information is available at http://www.semikron.com. For design support please read the SEMIKRON Application Manual Power Modules available at http://www.semikron.com. General Description ® ® The Board 1 SKYPER 32PRO is an adaptor board for the IGBT module e.g. SEMITRANS™, SEMiX (solder pin version). The board can be customized allowing adaptation and optimization to the used IGBT module. The switching characteristic of the IGBT can be influenced through user settings, e.g. changing turn-on and turn-off speed by variation of RGon and RGoff. Furthermore, it is possible to adjust the monitoring level and blanking time for the DSCP, soft ® turn-off behaviour as well as an over temperature trip level by using the temperature sensor integrated in SEMiX modules ® (see Technical Explanations SKYPER 32PRO). Please note: This technical explanation is based on the Technical Explanations for SKYPER® 32PRO. Please read the Technical Explanations SKYPER® 32PRO before using the Adaptor Board. Board 1 SKYPER® 32PRO 3 Rev. 02 – 21.04.2010 © by SEMIKRON Board 1 SKYPER® 32PRO R - Technical Explanations Dimensions 6 X200 66 1 X12 1 X100 1 2 1 2 9 10 19 20 9 10 Ø 3,2 X20 60 1 2 1 2 2 1 X10 9 10 9 10 20,3 21,57 1 Dimensions in mm Component Placement Layout Adaptor Board 4 Rev. 02 – 21.04.2010 © by SEMIKRON Board 1 SKYPER® 32PRO R - Technical Explanations PIN Array (not SKiiP® compatible) Connector X20 (ODU FLAKAFIX 511.068.803.020) Product information of suitable female connectors and distributor contact information is available at e.g. http://www.harting.com (part number 09 18 520 6 813). PIN Signal Function Specification X20:01 X20:02 IF_PWR_15P Drive power supply Stabilised +15V ±4% IF_PWR_GND GND for power supply X20:03 IF_PWR_15P Drive power supply X20:04 IF_PWR_GND GND for power supply X20:05 IF_PWR_15P Drive power supply X20:06 IF_PWR_GND GND for power supply X20:07 reserved X20:08 IF_PWR_GND GND for power supply X20:09 IF_CMN_nHALT Driver core status signal (bidirectional signal with dominant recessive behaviour) X20:10 reserved X20:11 reserved X20:12 IF_CMN_GND X20:13 reserved X20:14 reserved X20:15 IF_HB_TOP Switching signal input (TOP switch) Digital 15 V logic; 10 kOhm impedance; LOW = TOP switch off; HIGH = TOP switch on X20:16 IF_HB_BOT Switching signal input (BOTTOM switch) Digital 15 V logic; 10 kOhm impedance; LOW = BOT switch off; HIGH = BOT switch on X20:17 reserved X20:18 IF_HB_GND X20:19 reserved X20:20 reserved 5 Stabilised +15V ±4% Stabilised +15V ±4% Digital 15V logic; LOW (dominant) = driver disabled; HIGH (recessive) = ready to operate GND for signal IF_CMN_nHALT GND for signals IF_HB_TOP & IF_HB_BOT Rev. 02 – 21.04.2010 © by SEMIKRON Board 1 SKYPER® 32PRO R - Technical Explanations PIN Array – Secondary Side Connector X100, X200 (MOLEX Series 41791, Part Number 26-60-4050) Product information of suitable female connectors and distributor contact information is available at e.g. http://www.molex.com (e.g. series 41695). PIN Signal Function Specification X100:01 EMITTER_TOP Emitter output TOP IGBT X100:02 reserved X100:03 GATE_TOP Gate output TOP IGBT X100:05 VCE_TOP Collector output TOP IGBT X200:01 EMITTER_BOT Emitter output BOT IGBT X200:02 reserved X200:03 GATE_BOT Gate output BOT IGBT X200:05 VCE_BOT Collector output BOT IGBT Connector X12 (MOLEX Series 41791, Part Number 26-60-4020) Product information of suitable female connectors and distributor contact information is available at e.g. http://www.molex.com (e.g. series 41695). PIN Signal Function Specification X12:01 SENSE_TEMP_T1 Input temperature signal NTC + / PTC + X12:02 SENSE_TEMP_T2 Input temperature signal NTC - / PTC - 6 Rev. 02 – 21.04.2010 © by SEMIKRON Board 1 SKYPER® 32PRO R - Technical Explanations Signal IF_CMN_nHALT The Halt Logic Signals PRIM_HALT_IN and PRIM_HALT_OUT of the driver core are coupled to one bidirectional signal (IF_CMN_nHALT) with dominant recessive behaviour. IF_CMN_nHALT shows the driver core status. When IF_CMN_nHALT is HIGH (recessive), the driver core is ready to operate. When IF_CMN_nHALT is LOW (dominant), the driver core is disabled / not ready to operate because of e. g. detected failure or driver core system start. A controller can hold with the IF_CMN_nHALT signal the driver core in a safe state (e.g. during a start up of a system or gathered failure signal of other hardware) or generate a coeval release of paralleled driver. Furthermore, paralleled drivers can send and receive IF_CMN_nHALT signals among each other by using a single-wire bus. Connection IF_CMN_nHALT Setting Dead Time DT adjustment Designation R43 (connected to GND) R44 (connected to GND) R45 (connected to GND) R46 (connected to GND) Shape Setting 0603 (SMD) PRIM_CFG_TDT2_IN Factory setting: 0Ω 0603 (SMD) PRIM_CFG_SELECT_IN Factory setting: not equipped 0603 (SMD) PRIM_CFG_TDT3_IN Factory setting: 0Ω 0603 (SMD) PRIM_CFG_TDT1_IN Factory setting: not equipped Factory setting: 3,3µs Setting Dynamic Short Circuit Protection RCE & CCE 7 Designation Shape R162 1206 (SMD) C150 1206 (SMD) R262 1206 (SMD) C260 1206 (SMD) Setting RCE Factory setting: not equipped CCE Factory setting: not equipped RCE Factory setting: not equipped CCE Factory setting: not equipped Rev. 02 – 21.04.2010 TOP TOP BOT BOT © by SEMIKRON Board 1 SKYPER® 32PRO R - Technical Explanations Collector Series Resistance RVCE Designation Setting R150 MiniMELF (SMD) R250 MiniMELF (SMD) RVCE * Factory setting: not equipped RVCE * Factory setting: not equipped TOP BOT * 1200V IGBT operation: 0Ω * 1700V IGBT operation: 1kΩ / 0,4W * Adaptation Gate Resistors RGon & RGoff Designation Shape Setting R151, R152, R153 (parallel connected) MiniMELF (SMD) RGon Factory setting: not equipped TOP R154, R155, R156 (parallel connected) MiniMELF (SMD) RGoff Factory setting: not equipped TOP R251, R252, R253 (parallel connected) MiniMELF (SMD) RGon Factory setting: not equipped BOT R254, R255, R256 (parallel connected) MiniMELF (SMD) RGoff Factory setting: not equipped BOT Setting Soft Turn-Off RGoff_SC Designation R160, R161 (parallel connected) R260, R261 (parallel connected) 8 Shape MiniMELF (SMD) MiniMELF (SMD) Rev. 02 – 21.04.2010 Setting RGoff_SC Factory setting: not equipped RGoff_SC Factory setting: not equipped TOP BOT © by SEMIKRON Board 1 SKYPER® 32PRO R - Technical Explanations Over Temperature Protection Circuit (OTP) The external error input SEC_TOP_ERR_IN on the secondary side (high potential) of the driver core is used for an over temperature protection circuit to place the gate driver into halt mode. Dimensioning OTP If no temperature sensor is connected: - R172: 0Ω (factory setting: not equipped) - R175: not equip (factory setting: equipped) - R177: not equip (factory setting: not equipped) If a NTC temperature sensor is connected: 1. Define an over temperature trip level according to the application. 2. Calculate the nominal ohmic resistance value of the temperature sensor at the defined trip level according to the IGBT Module explanation. 3. The trip level on the adapter board is set with R172 (factory setting: not equipped) by using the calculated resistance value. 4. R177 = 450kΩ2 / RNTC(@ -40°C)[kΩ] (factory setting: not equipped) 5. R175: equip (factory setting: equipped) If a PTC temperature sensor is connected: 1. Define an over temperature trip level according to the application. 2. Calculate the nominal ohmic resistance value of the temperature sensor at the defined trip level according to the IGBT Module explanation. 3. The trip level on the adapter board is set with R177 = 450kΩ2 / Rcalculated_resistance[kΩ] (factory setting: not equipped) 4. R172 = 0Ω (factory setting: not equipped) 5. R175: equip (factory setting: equipped) Mounting Notes Driver Core Mounting 1. Soldering of components (e.g. RGon, RGoff, etc.) on adaptor board. 2. Insert driver core into the box connector on adaptor board. 3. The connecting leads between board and power module should be as short as possible (max. 20cm), the leads should be twisted. The connection between driver core and adaptor board should be mechanical reinforced by using support posts. The posts have to be spaced between driver core and adaptor board. Product information of suitable support posts and distributor contact information is available at e.g. http://www.richco-inc.com (e.g. part number DLMSPM-8-01, LCBST-8-01). 9 Rev. 02 – 21.04.2010 © by SEMIKRON Board 1 SKYPER® 32PRO R - Technical Explanations Schematics Schematic I Adaptor Board 10 Rev. 02 – 21.04.2010 © by SEMIKRON Board 1 SKYPER® 32PRO R - Technical Explanations Schematic II Adaptorboard 11 Rev. 02 – 21.04.2010 © by SEMIKRON Board 1 SKYPER® 32PRO R - Technical Explanations Parts List Parts List Adaptor Board Count Ref. Designator 8 C170, C171, C173, C174, C175, C176, CD20, CN170, Value Pattern Name 100nF 0805 (SMD) Capacitor X7R 6 1 1 1 2 1 1 2 1 1 2 2 3 1 3 6 1 2 3 1 1 1 1 2 1 2 2 1 5 1 4 2 1 1 C20, C21, C22, C23, C24, C25 C27 C28 C32 C35, C151 C36 D20 L150, L151 N170 R100 R157, R171 R163, R263 R173, R174, R176 R175 R28, R50, R52 R30, R31, R32, R33, R34, R37 R36 R43, R45 R47, R54, R56 R51 R53 R57 R58 R60, R61 R62 V150, V250 V170, V171 V20 V23, V25, V26, V27, V29 V28 X10, X11, X101, X201 X100, X200 X12 X20 1nF 2,2µF 220uF/35V 68pF 1uF 100pF 74C14 100uH LM2904 10,0Ohm 15,0KOhm 10,0KOhm 30,1KOhm 5,62KOhm 10,0KOhm 5,11KOhm 3,32KOhm 0,00Ohm 10,0KOhm 121KOhm 100Ohm 1,50KOhm 1,00KOhm 2,00KOhm 3,92KOhm BY203/20S BAV70W SMCJ15 BC847B BZX284-C7V5 RM2,54 10p. 5p. 2p. 20p. 0805 (SMD) 1210 (SMD) SMD 0603 (SMD) 1206 (SMD) 0603 (SMD) SOIC 14 (SMD) SIMID02 (SMD) SOIC 8 (SMD) 0603 (SMD) 0603 (SMD) MiniMelf (SMD) 0603 (SMD) MiniMelf (SMD) MikroMelf (SMD) MikroMelf (SMD) 0603 (SMD) 0603 (SMD) 0603 (SMD) 0603 (SMD) MikroMelf (SMD) MikroMelf (SMD) 0603 (SMD) 0603 (SMD) 0603 (SMD) Capacitor X7R Capacitor X7R Longlife-Elko Capacitor NP0 Capacitor X7R Capacitor NP0 Logic-IC 74C... Inductor Operational Amplifier 1% 1% 1% 1% 1% 1% 1% 1% SOT323 (SMD) DO214AB (SMD) SOT23 (SMD) SOD110 (SMD) SMD SMD Description 1% 1% 1% 1% 1% 1% 1% High Voltage Diode Double Diode Suppressor Diode NPN-Transistor Zener-Diode Box Connector Connector Connector Connector TP: Test Point Box Connector: SUYIN 254100FA010G200ZU DISCLAIMER SEMIKRON reserves the right to make changes without further notice herein to improve reliability, function or design. Information furnished in this document is believed to be accurate and reliable. However, no representation or warranty is given and no liability is assumed with respect to the accuracy or use of such information. SEMIKRON does not assume any liability arising out of the application or use of any product or circuit described herein. Furthermore, this technical information may not be considered as an assurance of component characteristics. No warranty or guarantee expressed or implied is made regarding delivery, performance or suitability. This document supersedes and replaces all information previously supplied and may be superseded by updates without further notice. SEMIKRON products are not authorized for use in life support appliances and systems without the express written approval by SEMIKRON. www.SEMIKRON.com 12 Rev. 02 – 21.04.2010 © by SEMIKRON