SKYPER 32 R UL Absolute Maximum Ratings Symbol SKYPER ® IGBT Driver Core Supply voltage primary 16 V Input signal voltage (HIGH) Vs + 0.3 V GND - 0.3 V ViL Input signal voltage (LOW) IoutPEAK Output peak current 15 A IoutAVmax Output average current 50 mA fmax Max. switching frequency 50 kHz VCE Collector emitter voltage sense across the IGBT 1700 V dv/dt Rate of rise and fall of voltage secondary to primary side 50 kV/µs 4000 V 1500 V 1500 V " VisolPD Visol12 • • • • • • • • • • UL recognized according UL 508C UL report reference E242581 Two output channels Integrated potential free power supply Under voltage protection Drive interlock top / bottom Dynamic short cirucit protection Shut down input Failure management IEC 60068-1 (climate) 40/085/56, no condensation and no dripping water permitted, non-corrosive, climate class 3K3 acc. EN60721 Unit Vs Preliminary Data Features Values ViH Visol IO SKYPER 32 R UL Conditions Isolation test voltage input - output (AC, rms, 2s) Partial discharge extinction voltage, rms, QPD ! 10pC Isolation test voltage output 1 - output 2 (AC, rms, 2s) RGon min Minimum rating for external RGon 1.5 RGoff min Minimum rating for external RGoff 1.5 " Qout/pulse Max. rating for output charge per pulse 2.5 µC Top Operating temperature -40 ... 85 °C Tstg Storage temperature -40 ... 85 °C Characteristics Symbol Conditions min. typ. max. 14.4 15 15.6 Unit Vs Supply voltage primary side ISO Supply current primary (no load) Typical Applications* Vi Input signal voltage on / off • Driver for IGBT modules in bridge circuits in industrial application • DC bus voltage up to 1200V VIT+ Input treshold voltage HIGH VIT- Input threshold voltage (LOW) RIN Input resistance (switching/HALT signal) 10 k" VG(on) Turn on output voltage 15 V 80 Supply current primary side (max.) Footnotes VCE: With external high voltage diode VisolIO/Visol12: Isolation test is not performed as a series test at SEMIKRON and must be performed by the user VisolPD: According to VDE 0110-20 Qout/pulse can be expanded to 6,3µQ with boost capacitors 450 15 / 0 mA V 12.3 4.6 V V VG(off) Turn off output voltage -7 V fASIC Asic system switching frequency 8 MHz td(on)IO Input-output turn-on propagation time 1.1 µs td(off)IO Input-output turn-off propagation time 1.1 µs td(err) Error input-output propagation time tpERRRESET Error reset time Isolation coordination in compliance with EN50178 PD2 Operating temperature is real ambient temperature around the driver core Degree of protection: IP00 V mA 5.4 7.9 9 µs µs tTD Top-Bot interlock dead time 3 Cps Coupling capacitance prim sec 12 pF 28 g w 4.3 µs MTBF Mean Time Between Failure Ta = 40°C 2.5 106h This is an electrostatic discharge sensitive device (ESDS), international standard IEC 60747-1, Chapter IX * The specifications of our components may not be considered as an assurance of component characteristics. Components have to be tested for the respective application. Adjustments may be necessary. The use of SEMIKRON products in life support appliances and systems is subject to prior specification and written approval by SEMIKRON. We therefore strongly recommend prior consultation of our personal. Driver Core © by SEMIKRON Rev. 0 – 11.08.2010 1 SKYPER® 32 R UL Technical Explanations Revision Status: Prepared by: 00 Johannes Krapp This Technical Explanation is valid for the following parts: part number: date code (YYWW): L6100104 ≥ 1030 Related Documents: title: Data Sheet SKYPER 32 R UL SKYPER® 32 R UL Content Application and Handling Instructions .................................................................................................................... 2 Further application support ..................................................................................................................................... 2 General Description ................................................................................................................................................ 2 Features of SKYPER 32 R UL................................................................................................................................ 2 UL specified remarks .............................................................................................................................................. 3 Block diagram ......................................................................................................................................................... 3 Dimensions ............................................................................................................................................................. 3 PIN Array – Primary Side........................................................................................................................................ 4 PIN Array – Secondary Side................................................................................................................................... 5 Driver Performance................................................................................................................................................. 6 Insulation................................................................................................................................................................. 6 Isolation Test Voltage ............................................................................................................................................. 7 Auxiliary Power Supply ........................................................................................................................................... 7 Under Voltage Protection of driver power supply (UVP) ........................................................................................ 8 Input Signals ........................................................................................................................................................... 8 Short Pulse Suppression (SPS) ............................................................................................................................. 8 Failure Management............................................................................................................................................... 9 Shut Down Input (SDI)............................................................................................................................................ 9 Dead Time generation (Interlock TOP / BOT) (DT).............................................................................................. 10 Dynamic Short Circuit Protection by VCEsat monitoring / de-saturation monitoring (DSCP).................................. 10 Adjustment of DSCP............................................................................................................................................. 11 High Voltage Diode for DSCP............................................................................................................................... 12 Gate resistors ....................................................................................................................................................... 12 External Boost Capacitors (BC)............................................................................................................................ 13 Application Example ............................................................................................................................................. 13 Mounting Notes..................................................................................................................................................... 14 Environmental Conditions..................................................................................................................................... 14 Marking ................................................................................................................................................................. 15 1 Rev 0 – 11.08.2010 © by SEMIKRON SKYPER® 32 R UL Please note: Unless otherwise specified, all values in this technical explanation are typical values. Typical values are the average values expected in large quantities and are provided for information purposes only. These values can and do vary in different applications. All operating parameters should be validated by user’s technical experts for each application. Application and Handling Instructions Please provide for static discharge protection during handling. As long as the hybrid driver is not completely assembled, the input terminals have to be short-circuited. Persons working with devices have to wear a grounded bracelet. Any synthetic floor coverings must not be statically chargeable. Even during transportation the input terminals have to be short-circuited using, for example, conductive rubber. Worktables have to be grounded. The same safety requirements apply to MOSFET- and IGBT-modules. Any parasitic inductances within the DC-link have to be minimised. Over-voltages may be absorbed by C- or RCDsnubbers between main terminals for PLUS and MINUS of the power module. When first operating a newly developed circuit, SEMIKRON recommends to apply low collector voltage and load current in the beginning and to increase these values gradually, observing the turn-off behaviour of the free-wheeling diode and the turn-off voltage spikes generated across the IGBT. An oscillographic control will be necessary. Additionally, the case temperature of the module has to be monitored. When the circuit works correctly under rated operation conditions, short-circuit testing may be done, starting again with low collector voltage. It is important to feed any errors back to the control circuit and to switch off the device immediately in failure events. Repeated turn-on of the IGBT into a short circuit with a high frequency may destroy the device. The inputs of the hybrid driver are sensitive to over-voltage. Voltages higher than VS +0,3V or below -0,3V may destroy these inputs. Therefore, control signal over-voltages exceeding the above values have to be avoided. The connecting leads between hybrid driver and the power module should be as short as possible (max. 20cm), the driver leads should be twisted. Further application support Latest information is available at http://www.semikron.com. For design support please read the SEMIKRON Application Manual Power Modules available at http://www.semikron.com. General Description The SKYPER 32 core constitutes an interface between IGBT modules and the controller. The driver is developed according to the requirements of UL standard. This core is a half bridge driver. Basic functions for driving, potential separation and protection are integrated in the driver. Thus it can be used to build up a driver solution for IGBT modules. Features of SKYPER 32 R UL Two output channels Integrated potential free power supply for the secondary side Short Pulse Suppression (SPS) Under Voltage Protection (UVP) Drive interlock (dead time) top / bottom (DT) Dynamic Short Circuit Protection (DSCP) by VCE monitoring and direct switch off Shut Down Input (SDI) Failure Management Expandable by External Boost Capacitors (BC) DC bus voltage up to 1200V 2 Rev 0 – 11.08.2010 SKYPER 32 © by SEMIKRON SKYPER® 32 R UL UL specified remarks The equipment shall be installed in compliance with the mounting and spacing requirements of the end-use application. SKYPER 32 shall be supplied by an isolated limited voltage / limited current source or a Class 2 source. The 15 A peak rating is an instantaneous peak rating only. These devices do not incorporate solid-state motor overload protection. The need for overload protection and overcurrent protection devices shall be determined in the end-use product. These devices have not been evaluated to over-voltage, over-current, and over-temperature control, and may need to be subjected to the applicable end-product tests. Temperature and tests shall be considered in the end use. Due to the limited current source, only the effect of heat generating components in this device on adjacent components in the end product needs to be considered. Connectors have not been evaluated field wiring; all connections are to be factory wired only. Block diagram Block diagram Dimensions (top view) 10,3 10,3 Dimensions in mm (bottom view) ±0,2mm unless otherwise noted 3 Rev 0 – 11.08.2010 © by SEMIKRON SKYPER® 32 R UL PIN Array – Primary Side Connectors Connector X10 (RM2,54, 10pin) ±0,25mm unless otherwise noted PIN Signal Function X10:01 PRIM_PWR_GND GND for power supply and GND for digital signals X10:02 PRIM_PWR_GND GND for power supply and GND for digital signals X10:03 PRIM_nERROR_OUT ERROR output LOW = NO ERROR; open collector output; max. 30V / 15mA (external pull up resistor necessary) X10:04 PRIM_nERROR_IN ERROR input 5V logic; LOW active X10:05 PRIM_PWR_GND GND for power supply and GND for digital signals X10:06 PRIM_PWR_GND GND for power supply and GND for digital signals X10:07 PRIM_TOP_IN Switching signal input (TOP switch) Digital 15 V; 10 kOhm impedance; LOW = TOP switch off; HIGH = TOP switch on X10:08 PRIM_BOT_IN Switching signal input (BOTTOM switch) Digital 15 V; 10 kOhm impedance; LOW = BOT switch off; HIGH = BOT switch on X10:09 PRIM_PWR_15P Drive core power supply Stabilised +15V ±4% X10:10 PRIM_PWR_15P Drive core power supply Stabilised +15V ±4% 4 Specification Rev 0 – 11.08.2010 © by SEMIKRON SKYPER® 32 R UL PIN Array – Secondary Side Connectors Connector X100 / X200 (RM2,54, 10pin) ±0,25mm unless otherwise noted PIN Signal Function X100:01 SEC_TOP_VCE_CFG Input reference voltage adjustment X100:02 SEC_TOP_VCE_IN Input VCE monitoring X100:03 SEC_TOP_15P Output power supply for external buffer capacitors Stabilised +15V X100:04 SEC_TOP_15P Output power supply for external buffer capacitors Stabilised +15V X100:05 SEC_TOP_GND GND for power supply and GND for digital signals X100:06 SEC_TOP_IGBT_ON Switch on signal TOP IGBT X100:07 SEC_TOP_GND GND for power supply and GND for digital signals X100:08 SEC_TOP_IGBT_OFF Switch off signal TOP IGBT X100:09 SEC_TOP_8N Output power supply for external buffer capacitors Stabilised -7V X100:10 SEC_TOP_8N Output power supply for external buffer capacitors Stabilised -7V X200:01 SEC_BOT_VCE_CFG Input reference voltage adjustment X200:02 SEC_BOT_VCE_IN Input VCE monitoring X200:03 SEC_BOT_15P Output power supply for external buffer capacitors Stabilised +15V X200:04 SEC_BOT_15P Output power supply for external buffer capacitors Stabilised +15V X200:05 SEC_BOT_GND GND for power supply and GND for digital signals X200:06 SEC_BOT_IGBT_ON Switch on signal BOT IGBT X200:07 SEC_BOT_GND GND for power supply and GND for digital signals X200:08 SEC_BOT_IGBT_OFF Switch off signal BOT IGBT X200:09 SEC_BOT_8N Output power supply for external buffer capacitors Stabilised -7V X200:10 SEC_BOT_8N Output power supply for external buffer capacitors Stabilised -7V 5 Specification Rev 0 – 11.08.2010 © by SEMIKRON SKYPER® 32 R UL Driver Performance The driver is designed for application with half bridges or single modules and a maximum gate charge per pulse < 2,5µC (< 6,3µC with external boost capacitors). The charge necessary to switch the IGBT is mainly depending on the IGBT’s chip size, the DC-link voltage and the gate voltage. This correlation is shown in module datasheets. It should, however, be considered that the driver is turned on at +15V and turned off at -7V. Therefore, the gate voltage will change by 22V during each switching procedure. Unfortunately, many datasheets do not show negative gate voltages. In order to determine the required charge, the upper leg of the charge curve may be prolonged to +22V for determination of approximate charge per switch. The medium output current of the driver is determined by the switching frequency and the gate charge. The maximum switching frequency may be calculated with the shown equation and is limited by the average current of the driver power supply and the power dissipation of driver components. Calculation Switching Frequency Maximum Switching Frequency @ different Gate Charges @ Tamb=25°C 60 kHz fmax: Iout AV max QGE Maximum switching frequency * IoutAVmax: Maximum output average current QGE: 50 kHz switching frequency fmax = 40 kHz 30 kHz 20 kHz Gate charge of the driven IGBT 10 kHz with external boost capacitors * @ Tamb=25°C 0 kHz 0 µC Calculation Average Output Current 1 µC 2 µC 3 µC 4 µC gate charge 5 µC 6 µC 7 µC Average Output Current as a Function of the Ambient Temperature 60 mA 50 mA IoutAV: Average output current fsw: Switching frequency QGE: Gate charge of the driven IGBT average output current Iout AV = fsw × Q GE 40 mA 30 mA 20 mA 10 mA 0 mA 0 °C 10 °C 20 °C 30 °C 40 °C 50 °C ambient temperature 60 °C 70 °C 80 °C 90 °C Please note: The maximum value of the switching frequency is limited to 50kHz due to switching reasons. Insulation Magnetic transformers are used for insulation between gate driver primary and secondary side. The transformer set consists of pulse transformers which are used bidirectional for turn-on and turn-off signals of the IGBT and the error feedback between secondary and primary side, and a DC/DC converter. This converter provides a potential separation (galvanic separation) and power supply for the two secondary (TOP and BOT) sides of the driver. Thus, external transformers for external power supply are not required. Creepage and Clearance Distance in mm Primary to secondary 6 Min. 12,2 Rev 0 – 11.08.2010 © by SEMIKRON SKYPER® 32 R UL Isolation Test Voltage The isolation test voltage represents a measure of immunity to transient voltages. The maximum test voltage and time applied once between input and output, and once between output 1 and output 2 are indicated in the absolute maximum ratings. The high-voltage isolation tests and repeated tests of an isolation barrier can degrade isolation capability due to partial discharge. Repeated isolation voltage tests should be performed with reduced voltage. The test voltage must be reduced by 20% for each repeated test. The isolation of the isolation barrier (transformer) is checked in the part. With exception of the isolation barrier, no active parts, which could break through are used. An isolation test is not performed as a series test. Therefore, the user can perform once the isolation test with voltage and time indicated in the absolute maximum ratings. Please note: An isolation test is not performed at SEMIKRON as a series test. Auxiliary Power Supply A few basic rules should be followed when dimensioning the customer side power supply for the driver. The following table shows the required features of an appropriate power supply. Requirements of the auxiliary power supply Regulated power supply +15V ±4% Maximum rise time of auxiliary power supply 50ms Minimum peak current of auxiliary supply 1A Power on reset completed after 150ms Please note: Do not apply switching signals during power on reset. The supplying switched mode power supply may not be turned-off for a short time as consequence of its current limitation. Its output characteristic needs to be considered. Switched mode power supplies with fold-back characteristic or hiccup-mode can create problems if no sufficient over current margin is available. The voltage has to rise continuously and without any plateau formation as shown in the following diagram. Rising slope of the power supply voltage If the power supply is able to provide a higher current, a peak current will flow in the first instant to charge up the input capacitances on the driver. Its peak current value will be limited by the power supply and the effective impedances (e.g. distribution lines), only. It is recommended to avoid the paralleling of several customer side power supply units. Their different set current limitations may lead to dips in the supply voltage. The driver is ready for operation typically 150ms after turning on the supply voltage. The driver error signal PRIM_nERROR_OUT is operational after this time. Without any error present, the error signal will be reset. To assure a high level of system safety the TOP and BOT signal inputs should stay in a defined state (OFF state, LOW) during driver turn-on time. Only after the end of the power-on-reset, IGBT switching operation shall be permitted. 7 Rev 0 – 11.08.2010 © by SEMIKRON SKYPER® 32 R UL Under Voltage Protection of driver power supply (UVP) The internally detected supply voltage of the driver has an under voltage protection. The table below gives an overview of the trip level. Supply voltage UVP level Regulated +15V ±4% 13,5V If the internally detected supply voltage of the driver falls below this level, the IGBTs will be switched off (IGBT driving signals set to LOW). The input side switching signals of the driver will be ignored. The error memory will be set, and the output PRIM_nERROR_OUT changes to the HIGH state. Input Signals The signal transfer to each IGBT is made with pulse transformers, used for switching on and switching off of the IGBT. The inputs have a Schmitt Trigger characteristic and a positive / active high logic (input HIGH = IGBT on; input LOW = IGBT off). It is mandatory to use circuits which switch active to +15V and 0V. Pull up and open collector output stages must not be used for TOP / BOT control signals. It is recommended choosing the line drivers according to the demanded length of the signal lines. Please note: It is not permitted to apply switching pulses shorter than 1µs. TOP / BOT Input A capacitor is connected to the input to obtain high noise immunity. This capacitor can cause for current limited line drivers a little delay of few ns, which can be neglected. The capacitors have to be placed as close as possible to the driver interface. Short Pulse Suppression (SPS) This circuit suppresses short turn-on and off-pulses of incoming signals. This way the IGBTs are protected against spurious noise as they can occur due to bursts on the signal lines. Pulses shorter than 625ns are suppressed and all pulses longer than 750ns get through for 100% probability. Pulses with a length in-between 625ns and 750ns can be either suppressed or get through. Pulse pattern – SPS short pulses PRIM_TOP/BOT_IN (HIGH) PRIM_TOP/BOT_IN (LOW) SEC_TOP/BOT_IGBT_ON SEC_TOP/BOT_IGBT_OFF 8 Rev 0 – 11.08.2010 © by SEMIKRON SKYPER® 32 R UL Failure Management Any error detected will set the error latch and force the output PRIM_nERROR_OUT into HIGH state. Switching pulses from the controller will be ignored. Connected and switched off IGBTs remain turned off. The switched off IGBTs remain turned off. A reset of the latched error memory is only possible if no failure is present anymore and if the TOP and BOT input signals are set to the LOW level for a period of tpERRRESET > 9µs. The output PRIM_nERROR_OUT is an open collector output. For the error evaluation an external pull-up-resistor is necessary pulled-up to the positive operation voltage of the control logic (LOW signal = no error present, wire break safety is assured). Open collector error transistor Application hints An external resistor to the controller logic high level is required. The resistor has to be in the range of V / Imax < Rpull_up < 10kΩ. PRIM_nERROR_OUT can operate to maximum 30V and can switch a maximum of 15mA. Example: For V = +15V the needed resistor should be in the range Rpull_up = (15V/15mA) … 10kΩ ⇒ 1kΩ… 10kΩ. Please note: The error output PRIM_ERROR_OUT is not short circuit proof. Shut Down Input (SDI) The shut down input / error input signal can gather error signals of other hardware components for switching off the IGBT (input HIGH = no turn-off; input LOW = turn-off). A LOW signal at PRIM_nERROR_IN will set the error latch and force the output PRIM_nERROR_OUT into HIGH state. Switching pulses from the controller will be ignored. A reset of the latched error memory is only possible if no LOW signal at PRIM_nERROR_IN is present anymore and if the TOP and BOT input signals are set to the LOW level for a period of tpERRRESET > 9µs. The SDI function can be disabled by no connection or connecting to 5V. Connection SDI 9 Rev 0 – 11.08.2010 © by SEMIKRON SKYPER® 32 R UL Dead Time generation (Interlock TOP / BOT) (DT) The DT circuit prevents, that TOP and BOT IGBT of one half bridge are switched on at the same time (shoot through). The dead time is not added to a dead time given by the controller. Thus the total dead time is the maximum of "built in dead time" and "controller dead time". It is possible to control the driver with one switching signal and its inverted signal. Please note: The generated dead time is fixed and cannot be changed. Pulse pattern – DT The total propagation delay of the driver is the sum of interlock dead time (tTD) and driver input output signal propagation delay (td(on;off)IO) as shown in the pulse pattern. Moreover the switching time of the IGBT chip has to be taken into account (not shown in the pulse pattern). In case both channel inputs (PRIM_TOP_IN and PRIM_BOT_IN) are at high level, the IGBTs will be turned off. If only one channel is switching, there will be no interlock dead time. Please note: No error message will be generated when overlap of switching signals occurs. Dynamic Short Circuit Protection by VCEsat monitoring / de-saturation monitoring (DSCP) The DSCP circuit is responsible for short circuit sensing. It monitors the collector-emitter voltage VCE of the IGBT during its on-state. Due to the direct measurement of VCEsat on the IGBT's collector, the DSCP circuit switches off the IGBTs and an error is indicated. The reference voltage VCEref may dynamically be adapted to the IGBTs switching behaviour. Immediately after turn-on of the IGBT, a higher value is effective than in steady state. This value will, however, be reset, when the IGBT is turned off. VCEstat is the steady-state value of VCEref and is adjusted to the required maximum value for each IGBT by an external resistor RCE. It may not exceed 10V. The time constant for the delay (exponential shape) of VCEref may be controlled by an external capacitor CCE, which is connected in parallel to RCE. It controls the blanking time tbl which passes after turn-on of the IGBT before the VCEsat monitoring is activated. This makes an adaptation to any IGBT switching behaviour possible. Reference Voltage (VCEref) Characteristic After tbl has passed, the VCE monitoring will be triggered as soon as VCE > VCEref and will turn off the IGBT. The error memory will be set, and the output PRIM_nERROR_OUT changes to the HIGH state. Possible failure modes are shows in the following pictures. 10 Rev 0 – 11.08.2010 © by SEMIKRON SKYPER® 32 R UL Short circuit during operation Turn on of IGBT too slow * Short circuit during turn on * or adjusted blanking time too short Adjustment of DSCP The external components RCE and CCE are applied for adjusting the steady-state threshold the blanking time. Connection RCE and CCE Dimensioning of RCE and CCE V VCEstat + R VCE ⋅ kΩ R CE [kΩ ] = −17kΩ ⋅ ln 1 − 8,5 V C CE [ pF ] = t bl [µs ] − 2,5µs − 0,11 0,00323 µs ⋅ RCE kΩ µs pF VCEstat: Collector-emitter threshold static monitoring voltage tblx: Blanking time VCEstat_max = 8V (RVCE = 0Ω) VCEstat_max = 7V (RVCE = 1kΩ) Please Note: The equations are calculated considering the use of high voltage diode BY203/20S. The calculated values VCEstat and tbl are typical values at room temperature. These values can and do vary in the application (e.g. tolerances of used high voltage diode, resistor RCE, capacitor CCE). The DSCP function is not recommended for over current protection. Application hints If the DSCP function is not used, for example during the experimental phase, SEC_TOP_VCE_IN must be connected with SEC_TOP_GND for disabling SCP @ TOP side and SEC_BOT_VCE_IN must be connected with SEC_BOT_GND for disabling SCP @ BOT side. 11 Rev 0 – 11.08.2010 © by SEMIKRON SKYPER® 32 R UL High Voltage Diode for DSCP The high voltage diode blocks the high voltage during IGBT off state. The connection of this diode between driver and IGBT is shown in the following schematic. Connection High Voltage Diode Characteristics Reverse blocking voltage of the diode shall be higher than the used IGBT. Reverse recovery time of the fast diode shall be lower than VCE rising of the used IGBT. Forward voltage of the diode: 1,5V @ 2mA forward current (Tj=25°C). A collector series resistance RVCE (1kΩ / 0,4W) must be connected for 1700V IGBT operation. Gate resistors The output transistors of the driver are MOSFETs. The sources of the MOSFETs are separately connected to external terminals in order to provide setting of the turn-on and turn-off speed of each IGBT by the external resistors RGon and RGoff. As an IGBT has input capacitance (varying during switching time) which must be charged and discharged, both resistors will dictate what time must be taken to do this. The final value of the resistance is difficult to predict, because it depends on many parameters as DC link voltage, stray inductance of the circuit, switching frequency and type of IGBT. Connection RGon, RGoff Application Hints The gate resistor influences the switching time, switching losses, dv/dt behaviour, etc. and has to be selected very carefully. Due to this influence a general value for the gate resistors cannot be recommended. The gate resistor has to be optimized according to switching behaviour and over voltage peaks within the specific circuitry. By increasing RGon the turn-on speed will decrease. The reverse peak current of the free-wheeling diode will diminish. By increasing RGoff the turn-off speed of the IGBT will decrease. The inductive peak over voltage during turn-off will diminish. In order to ensure locking of the IGBT even when the driver supply voltage is turned off, a resistance (RGE) has to be integrated. Please note: Do not connect the terminals SEC_TOP_IGBT_ON with SEC_TOP_IGBT_OFF and SEC_BOT_IGBT_ON with SEC_BOT_IGBT_OFF, respectively. 12 Rev 0 – 11.08.2010 © by SEMIKRON SKYPER® 32 R UL External Boost Capacitors (BC) The rated gate charge of the driver may be increase by additional boost capacitors to drive IGBT with large gate capacitance. Connection External Boost Capacitors Dimensioning of Cboost Cboost15P [µF] = QGE [µC] × 1/V - 2,2µF Cboost8N [µF] = QGE [µC] × 2/V - 4,7µF QGE: Gate charge of the IGBT @ VGE = -7 …+15V Minimum rated voltage Cboost15P: 25V Minimum rated voltage Cboost8N: 16V Type of capacitor: ceramic capacitor Please consider the maximum rating four output charge per pulse of the gate driver. Application Hints The external boost capacitors should be connected as close as possible to the gate driver and to have low inductance. Application Example Connection Schematic DC+ SKYPERTM 32 SEC_TOP_VCE_CFG BY203/20S SEC_TOP_VCE_IN SEC_TOP_15P 18k 330pF 50V SEC_TOP_15P SEC_TOP_GND Ron SEC_TOP_IGBT_ON PRIM_PWR_GND 4,75k SEC_TOP_GND PRIM_PWR_GND SEC_TOP_IGBT_OFF ERROR OUT Roff PRIM_nERROR_OUT SEC_TOP_8N 4,7µF 2,2µF SEC_TOP_8N 16V 25V PRIM_nERROR_IN 10k PRIM_PWR_GND PRIM_PWR_GND SEC_BOT_VCE_CFG INPUT TOP load BY203/20S PRIM_TOP_IN SEC_BOT_VCE_IN INPUT BOT PRIM_BOT_IN SEC_BOT_15P 18k PRIM_PWR_15P +15V 330pF 50V SEC_BOT_15P PRIM_PWR_15P 1nF 1nF 1nF 100V 100V 100V SEC_BOT_GND 1nF 100V 220µF 35V Ron SEC_BOT_IGBT_ON SEC_BOT_GND SEC_BOT_IGBT_OFF Roff SEC_BOT_8N SEC_BOT_8N 4,7µF 2,2µF 16V 25V 10k DC- - 13 application example for 1200V IGBT Qout/pulse = 5µC VCEref = 5,5V tbl = 5,5µs Rev 0 – 11.08.2010 © by SEMIKRON SKYPER® 32 R UL Mounting Notes Soldering Hints Finished Hole & Pad Size in mm The temperature of the solder must not exceed 260°C, and solder time must not exceed 10 seconds. The ambient temperature must not exceed the specified maximum storage temperature of the driver. The solder joints should be in accordance to IPC A 610 Revision D (or later) Class 3 (Acceptability of Electronic Assemblies) to ensure an optimal connection between driver core and printed circuit board. Please note: The driver is not suited for hot air reflow or infrared reflow processes. The connection between driver core and printed circuit board should be mechanical reinforced by using support posts. Use of Support Posts Product information of suitable support posts and distributor contact information is available at e.g. http://www.richco-inc.com (e.g. series DLMSPM, LCBST). Please note: The use of agressive materials in cleaning and potting process of driver core may be detrimental for the device parameters. If the driver core is coated by the user, any warranty (Gewährleistung) expires. Environmental Conditions The driver core is type tested under the environmental conditions below. Conditions Values (max.) Vibration Sinusoidal sweep 20Hz … 500Hz, 5g, 26 sweeps per axis (x, y, z) Shock - Tested acc. IEC 68-2-6 - Connection between driver core and printed circuit board mechanical reinforced by using support posts. Half-sinusoidal pulse, 5g, shock width 18ms, 3 shocks in each direction (±x, ±y, ±z), 18 shocks in total - Tested acc. IEC 68-2-27 - Connection between driver core and printed circuit board mechanical reinforced by using support posts. The characteristics and further environmental conditions are indicated in the data sheet. 14 Rev 0 – 11.08.2010 © by SEMIKRON SKYPER® 32 R UL Marking Every driver core is marked. The marking contains the following items. Part Marking Information The Data Matrix Code is described as follows: Type: EEC 200 Standard: ICO / IEC 16022 Cell size: 0,254 - 0,3 mm Dimension: 5 × 5 mm The following data is coded: XXXXXXXXYY ZZZZ VVVV 2. Date code (4 digits): YYWW 8 digits 2 digits 1 digit 3. Continuous number referred to date coce (4 digits) 4 digits date code 4. Data matrix code 1 digit blank 4 digits continuous number 1. SEMIKRON part number (8 digits) + version number (2 digits) part number version number blank DISCLAIMER SEMIKRON reserves the right to make changes without further notice herein to improve reliability, function or design. Information furnished in this document is believed to be accurate and reliable. However, no representation or warranty is given and no liability is assumed with respect to the accuracy or use of such information. SEMIKRON does not assume any liability arising out of the application or use of any product or circuit described herein. Furthermore, this technical information may not be considered as an assurance of component characteristics. No warranty or guarantee expressed or implied is made regarding delivery, performance or suitability. This document supersedes and replaces all information previously supplied and may be superseded by updates without further notice. SEMIKRON products are not authorized for use in life support appliances and systems without the express written approval by SEMIKRON. www.SEMIKRON.com 15 Rev 0 – 11.08.2010 © by SEMIKRON