CX77105
Power Amplifier Module for CDMA/AMPS (824–849 MHz)
The CX77105, a dual-mode, Code Division Multiple Access (CDMA) / Advanced
Mobile Phone Service (AMPS) Power Amplifier Module (PAM), is a fully matched,
10-pin surface mount module developed for cellular handsets and wireless local loop
applications. This small and efficient power amplifier module packs a full 824–849
MHz bandwidth coverage into a single compact package. The device meets the
stringent IS95 CDMA linearity requirements to and exceeding 28 dBm output power,
and can be driven to levels beyond 31 dBm for high efficiency in FM mode operation.
A low current digital pin (VCONT) provides improved efficiency for the low RF power
range of operation.
Distinguishing Features
•
•
•
•
•
•
•
The single Gallium Arsenide (GaAs) Microwave Monolithic Integrated Circuit (MMIC) •
contains all active circuitry in the module. The MMIC contains on-board bias circuitry, •
as well as input and interstage matching circuits. The output match is realized off-chip •
and within the module package to optimize efficiency and power performance into a
50 Ω load. This device is manufactured with Skyworks’ GaAs Heterojunction Bipolar
Transistor (HBT) process that provides for all positive voltage DC supply operation
while maintaining high efficiency and good linearity. Primary bias to the CX77105 is
supplied directly from a three-cell nickel cadmium, a single-cell lithium ion, or other
suitable battery with an output in the 3–4 volt range. Power down is accomplished by
setting the voltage on the low current reference pin to zero volts. No external supply
side switch is needed as typical “off” leakage is a few microamperes with full primary
voltage supplied from the battery.
Low voltage positive bias supply
(3.2 V to 4.2 V, typical)
Good linearity
High efficiency
Dual mode operation
Large dynamic range
10-pin package (4 x 4 x 1.5 mm)
Power down control
Low power-state control
InGaP
IS 95/CDMA2000
Applications
•
•
•
Digital cellular (CDMA)
Analog cellular (AMPS)
Wireless local loop (WLL)
Functional Block Diagram
VREF
(1)
Driver
Stage Bias
RF IN (4)
Input
Match
VCC2
(6)
VCONT
(2)
VCC1
(5)
Power
Stage Bias
Inter
Stage
Match
DA
PA
Output
Match
(8) RF OUT
MMIC
MODULE
(3, 7, 9, 10)
GND
(3, 7, 9, 10)
GND
Data Sheet
© 2001, 2002 Skyworks Solutions, Inc., All Rights Reserved.
101787A
December 10, 2002
CX77105
Electrical Specifications
Power Amplifier Module for CDMA/AMPS (824–849 MHz)
Electrical Specifications
The following tables list the electrical characteristics of the CX77105 Power Amplifier. Table 2
lists the recommended operating conditions for achieving the electrical performance listed in
Table 4. Table 3 lists the electrical performance of the CX77105 Power Amplifier over the
recommended operating conditions.
Table 1. Absolute Maximum Ratings(1)
Parameter
Symbol
Minimum
Nominal
Maximum
Unit
RF Input Power
PIN
—
4.0
7.0
dBm
Supply Voltage
VCC
—
3.4
6.0
Volts
Reference Voltage
VREF
—
3.0
3.1
Volts
TC
–30
25
+110
o
C
TSTG
–55
—
+125
o
C
Case Operating Temperature
Storage Temperature
NOTE(S):
(1)
No damage assuming only one parameter is set at limit at a time with all other parameters set at or below
nominal value.
Table 2. Recommended Operating Conditions
Parameter
Symbol
Minimum
Nominal
Maximum
Unit
VCC
3.2
3.4
4.2
Volts
PA On
VREF
2.95
3.0
3.05
PA Off
VREF
—
—
0.5
High
Bias
VCONT
0.0
—
0.5
Low
Bias
VCONT
2.5
—
3.0
Operating Frequency
FO
824.0
836.5
849.0
MHz
Operating Temperature
TO
–30
—
+85
°C
Supply Voltage
Reference Voltage
Volts
Volts
Mode Input Impedance >2.5 kΩ
Table 3. Power Range Truth Table
Power Mode
2
VREF
VCONT
Range
High Power
3.0 V
0.0–0.5 V
16 dBm–28 dBm
Low Power
3.0 V
2.5–3.0 V
≤ 16 dBm
Shut Down
0.0 V
0.0 V
—
Skyworks Solutions, Inc. Proprietary
101787A
December 10, 2002
CX77105
Electrical Specifications
Power Amplifier Module for CDMA/AMPS (824–849 MHz)
Table 4. Electrical Specifications for CDMA / AMPS Nominal Operating Conditions(1)
Characteristics
Symbol
Digital
Mode
Gain conditions
Analog
Mode
Digital
Mode
Power Added Efficiency
GLOW
GHIGH
GP
PAELOW
PAEHIGH
Condition
VCONT ≥ 2.5 V
PO = 16 dBm
VCONT ≤ 0.5 V
PO = 28 dBm
VCONT ≤ 0.5 V
PO = 31 dBm
VCONT ≥ 2.5 V
PO = 16 dBm
VCONT ≤ 0.5 V
PO = 28 dBm
Minimum
Typical
Maximum
25.0
27.0
28.0
28.5
29.0
31.0
27.5
29.0
31.0
7.6
8.5
—
37.0
40.0
—
Unit
dB
%
PAEa
VCONT ≤ 0.5 V
PO = 31 dBm
48.0
55.0
—
Total Supply Current
ICC_LOW
ICC_HIGH
PO = 16 dBm
PO = 28 dBm
—
—
137
490
153
500
mA
Quiescent Current
IQ_LOW
IQ_HIGH
VCONT ≥ 2.5 V
VCONT ≤ 0.5 V
40
60
55
78
75
105
mA
Reference Current
IREF
—
—
2.5
5.0
mA
Control Current
ICTRL
VCONT = 2.5 V
200
235
500
µA
IPD
VCC = 3.4 V
VREF = 0 V
—
3.0
5.0
µA
—
–49.0
–47.3
—
–50.0
–47.0
—
–65.0
–59.0
—
–60.0
–57.4
Analog
Mode
Total Supply current in Power-down
Mode
885 kHz
offset
Adjacent Channel
Power(2)(3)
1.98
MHz
offset
Harmonic Suppression
101787A
December 10, 2002
ACP1LOW
ACP1HIGH
ACP2LOW
ACP2HIGH
VCONT ≥ 2.5 V
PO ≤ 16 dBm
VCONT ≤ 0.5 V
PO ≤ 28 dBm
VCONT ≥ 2.5 V
PO ≤ 16 dBm
or
VCONT ≤ 0.5 V
PO ≤ 28 dBm
Secon
d
FO2
PO ≤ 28 dBm
—
–38.0
–35.0
Third
FO3
PO ≤ 28 dBm
—
–59.0
–45.0
dBc
dBc
Skyworks Solutions, Inc. Proprietary
3
CX77105
Electrical Specifications
Power Amplifier Module for CDMA/AMPS (824–849 MHz)
Table 4. Electrical Specifications for CDMA / AMPS Nominal Operating Conditions(1)
Characteristics
Symbol
Condition
Minimum
Typical
Maximum
Unit
RxBN
PO ≤ 28 dBm
—
–137
—
dBm/Hz
NF
—
—
4.6
5.0
dB
VSWR
—
—
—
1.9:1
—
Stability (Spurious output)
S
5:1 VSWR
all phases
—
—
–60.0
dBc
Ruggedness—No damage(4)
Ru
PO ≤ 28 dBm
10:1
—
—
VSWR
Noise Power in RX Band 869-894 MHz
Noise Figure
Input Voltage Standing Wave Ratio
NOTE(S):
(1)
VCC = +3.4 V, VREF = +3.0 V, Freq = 836.5 MHz, TC = 25 °C, unless otherwise specified.
ACP is specified per IS95 as the ratio of the total in-band power (1.23 MHz BW) to adjacent power in a 30 kHz BW.
(3)
CDMA2000 is configured as DCCH = 9600, SCHO = 9600, PCH (Walsh 0) = – 3.75 dB, and Peak-to-Average Ratio
(CCDF = 1%) = 4.5 dB. For CDMA2000, 0.5 dB back-off in output power is required.
(4) All phases, time = 10 seconds.
(2)
Table 5. Electrical Specifications for CDMA / AMPS Recommended Operating Conditions(1)
Characteristics
Symbol
Digital
Mode
Gain conditions
Analog
Mode
1.25 MHz
offset
Adjacent Channel Power(2)(3)
GLOW
GHIGH
GP
ACP1LOW
ACP1HIGH
ACP2LOW
1.98 MHz
offset
ACP2HIGH
Minimum
Maximum
24.0
28.5
27.1
32.4
24.0
33.0
—
–44
dBc
—
–44
dBc
—
–56
dBc
—
–56
dBc
VCONT ≥ 2.5 V
PO = 16 dBm
VCONT ≤ 0.5 V
PO = 28 dBm
VCONT ≤ 0.5 V
PO = 31 dBm
VCONT ≥ 2.5 V
PO ≤ 16 dBm
VCONT ≤ 0.5 V
PO ≤ 28 dBm
VCONT ≥ 2.5 V
PO ≤ 16 dBm
or
VCONT ≤ 0.5 V
PO ≤ 28 dBm
Unit
dB
Second
F O2
PO ≤ 28 dBm
—
–30
dBc
Third
F O3
PO ≤ 28 dBm
—
–40
dBc
Harmonic Suppression
4
Condition
Skyworks Solutions, Inc. Proprietary
101787A
December 10, 2002
CX77105
Electrical Specifications
Power Amplifier Module for CDMA/AMPS (824–849 MHz)
Table 5. Electrical Specifications for CDMA / AMPS Recommended Operating Conditions(1)
Characteristics
Symbol
Condition
Minimum
Maximum
Unit
RxBN
PO ≤ 28 dBm
—
–134.0
dBm/Hz
NF
—
—
7.0
dB
VSWR
—
—
2.0:1
—
Stability (Spurious output)
S
5:1 VSWR
All phases
—
–60.0
dBc
Ruggedness – No damage(4)
Ru
PO ≤ 28dBm
10:1
—
VSWR
Noise Power in RX Band 869-894 MHz
Noise Figure
Input Voltage Standing Wave Ratio (VSWR)
NOTE(S):
(1)
Per Table 2, unless otherwise specified.
ACP is specified per IS95 as the ratio of the total in-band power (1.23 MHz BW) to adjacent power in a 30 kHz BW.
(3)
CDMA2000 is configured as DCCH = 9600, SCHO = 9600, PCH (Walsh 0) = –3.75 dB, and Peak-to-Average Ratio
(CCDF = 1%) = 4.5 dB. For CDMA2000, 0.5 dB back-off in output power is required.
(4) All phases, time = 10 seconds.
(2)
101787A
December 10, 2002
Skyworks Solutions, Inc. Proprietary
5
CX77105
Characterization Data
Power Amplifier Module for CDMA/AMPS (824–849 MHz)
Characterization Data
The following graphs illustrate the characteristics of a typical CX77105 power amplifier designed
for operation in the cellular frequency band (824–849 MHz). This amplifier was selected by
characterizing a group of devices and then selecting a part with average electrical performance for
both nominal and the full range of recommended operating conditions, including worst case limits.
Figures 1 through 7 illustrate the digital signal characteristics of the CX77105. Shown are power
sweep characteristics for key performance parameters, over temperature and frequency, up to 28.5
dBm output power. The data was taken up to and including 16 dBm output power with the bias
mode control pin setting of VCONT = 2.5 volts. Beyond 16 dBm output power, the VCONT was set to
0 volts.
Figure 1. Digital Mode Gain vs. Output Power
35
VREF = 3.0 V VCC = 3.4 V
34
33
32
31
Gain (dB)
30
29
28
27
+85 ˚C
26
+25 ˚C
25
–30 ˚C
24
23
VCONT > 2.5 V
VCONT < 0.5 V
22
21
20
0
5
10
15
20
25
30
Output Power (dBm)
101787_009
Legend
6
824 @ –30
30 ˚C
824 @ +25 ˚C
824 @ +85 ˚C
837 @ –30
30 ˚C
837 @ +25 ˚C
837 @ +85 ˚C
849 @ –30
30 ˚C
849 @ +25 ˚C
849 @ +85 ˚C
Skyworks Solutions, Inc. Proprietary
101787A
December 10, 2002
CX77105
Characterization Data
Power Amplifier Module for CDMA/AMPS (824–849 MHz)
Figure 2. Primary Bias Current vs. Output Power
VREF = 3.0 V
VCC = 3.4 V
600
500
Icc (mA)
400
VCONT > 2.5 V
VCONT < 0.5 V
300
200
100
0
0
5
10
15
20
25
30
Output Power (dBm)
101787_010
Figure 3. Power Added Efficiency vs. Output Power
VREF = 3.0 V VCC = 3.4 V
45
40
Power Added Efficiency (%)
35
30
25
VCONT > 2.5 V
VCONT < 0.5 V
20
15
10
5
0
0
5
10
15
20
25
30
Output Power (dBm)
101787_011
Legend
101787A
December 10, 2002
824 @ –30
30 ˚C
824 @ +25 ˚C
824 @ +85 ˚C
837 @ –30
30 ˚C
837 @ +25 ˚C
837 @ +85 ˚C
849 @ –30
30 ˚C
849 @ +25 ˚C
849 @ +85 ˚C
Skyworks Solutions, Inc. Proprietary
7
CX77105
Characterization Data
Power Amplifier Module for CDMA/AMPS (824–849 MHz)
Figure 4. Adjacent Channel Power for 885 kHz Offset Current vs. Output Power
VREF = 3.0 V VCC = 3.4 V
80
Adjacent Channel Power Ratio
75
70
+8
5˚
C
65
+2
5˚
C
VCONT > 2.5 V
60
VCONT < 0.5 V
–3
0˚
C
55
50
45
40
0
5
10
15
20
25
30
Output Power (dBm)
101787_012
Figure 5. Adjacent Channel Power for 1.98 MHz Offset vs. Output Power
VREF = 3.0 V
Vcc = 3.4 V
Adjacent Channel Power Ratio (-dBc)
90
85
+8
5˚
C
80
+2
5˚
C
75
–3
0˚
C
70
65
VCONT > 2.5 V
60
VCONT < 0.5 V
55
50
0
5
10
15
20
25
30
Output Power (dBm)
Legend
8
824 @ –30
30 ˚C
824 @ +25 ˚C
824 @ +85 ˚C
837 @ –30
30 ˚C
837 @ +25 ˚C
837 @ +85 ˚C
849 @ –30
30 ˚C
849 @ +25 ˚C
849 @ +85 ˚C
Skyworks Solutions, Inc. Proprietary
101787A
December 10, 2002
CX77105
Characterization Data
Power Amplifier Module for CDMA/AMPS (824–849 MHz)
Figure 6. Second Harmonic Rejection vs. Output Power
VREF = 3.0 V VCC = 3.4 V
2nd Harmonic Rejection (-dBc)
55
50
45
40
35
VCONT > 2.5 V
VCONT < 0.5 V
30
0
5
10
15
20
25
30
Output Power (dBm)
101787_014
Figure 7. Third Harmonic Rejection vs. Output Power
3rd Harmonic Rejection (-dBc)
70
VREF = 3.0 V VCC = 3.4 V
65
60
55
VCONT > 2.5 V
VCONT < 0.5 V
50
0
5
10
15
20
25
30
Output Power (dBm)
101787_015
Legend
101787A
December 10, 2002
824 @ –30
30 ˚C
824 @ +25 ˚C
824 @ +85 ˚C
837 @ –30
30 ˚C
837 @ +25 ˚C
837 @ +85 ˚C
849 @ –30
30 ˚C
849 @ +25 ˚C
849 @ +85 ˚C
Skyworks Solutions, Inc. Proprietary
9
CX77105
Characterization Data
Power Amplifier Module for CDMA/AMPS (824–849 MHz)
Figure 8. Noise Figure as Function of Operating Conditions
7
824
COLD
6
836.5
849
ROOM TEMPERATURE
HOT
Noise Figure (dB)
5
4
3
2
1
0
3.2 V
–30 ˚C
3.4 V
–30 ˚C
4.2 V
–30 ˚C
3.2 V
+25 ˚C
3.4 V
+25 ˚C
4.2 V
+25 ˚C
3.2 V
+85 ˚C
3.4 V
+85 ˚C
4.2 V
+85 ˚C
Collector Voltage / Case Temperature
101787_016
Figure 9. Input VSWR as Function of Operating Conditions
2.0
824
836.5
849
1.9
COLD
ROOM TEMPERATURE
HOT
1.8
1.7
VSWR
1.6
1.5
1.4
1.3
1.2
1.1
1.0
3.2 V
–30 ˚C
3.4 V
–30 ˚C
4.2 V
–30 ˚C
3.2 V
+25 ˚C
3.4 V
+25 ˚C
4.2 V
+25 ˚C
3.2 V
+85 ˚C
3.4 V
+85 ˚C
4.2 V
+85 ˚C
Collector Voltage / Case Temperature
101787_017
10
Skyworks Solutions, Inc. Proprietary
101787A
December 10, 2002
CX77105
Evaluation Board Description
Power Amplifier Module for CDMA/AMPS (824–849 MHz)
Evaluation Board Description
The evaluation board is a platform for testing and interfacing design circuitry. To accommodate the
interface testing of the CX77105, the evaluation board schematic and diagrams are included for
preliminary analysis and design. Figure 10 shows the basic schematic of the board for the 824 MHz
to 849 MHz range.
Figure 10. Evaluation Board Schematic
VREF
GND 10
1 VREF
C9
1000 pF
GND 9
2 VCONT
VCONT
RF OUT
C3
1000 pF
RF OUT 8
3 GND
RF IN
4 RF IN
GND 7
5 VCC1
VCC2 6
VCC2
VCC1
C6
10 µF
C4
1000 pF
C7
0.1 µF
C5
330 pF
101787_003
Figure 11. Evaluation Board Assembly Diagram
P1
RF IN
J1
CELLULAR 4X4
J2
C7
GND
GND
C3
VCT
VCC1
GND
U1
VCC2
C9
GND
GND
VREF
C5 C4
EN14-D1235-003
C6
12/17/01
RF OUT
P2
101787_002
101787A
December 10, 2002
Skyworks Solutions, Inc. Proprietary
11
CX77105
Package Dimensions and Pin Descriptions
Power Amplifier Module for CDMA/AMPS (824–849 MHz)
Package Dimensions and Pin Descriptions
The CX77105 is a multi-layer laminate base, overmold encapsulated modular package designed for
surface mount solder attachment to a printed circuit board.
Figure 12 is a mechanical drawing of the pad layout for this package. The pin numbering
convention starts with pin 1 in the upper left, as indicated in Figure 12, and increments
counter-clockwise around the package. Table 6 describes each pin function and Figure 13
illustrates typical case markings.
Figure 12. CX77105 Package Dimensional Drawing
1.9
1.275
1.0
SOLDER MASK EDGES
1.7
0.85
1.275
0.1
0.4 ± 0.05
1.9
0.4 ± 0.05
METAL PAD EDGES
DETAIL
PAD
A
A
R0.2
TOP VIEW
Note: Solder mask pattern pad layout as viewed
from top looking through package.
PIN 1
INDICATOR
0.48
0.45
10
2
9
3
8
4
7
5
6
1.5 ± 0.1
SIDE VIEW
4 ± 0.05
4 ± 0.05
TOP VIEW
All Dimensions in millimeters.
101787_004
12
Skyworks Solutions, Inc. Proprietary
101787A
December 10, 2002
CX77105
Package Dimensions and Pin Descriptions
Power Amplifier Module for CDMA/AMPS (824–849 MHz)
Table 6. Pin Descriptions
Pin #
Function
Pin #
Function
Pin #
Function
1
VREF
5
VCC1(1)
9
GND
10
GND
GND PAD(2)
GND
2
VCONT
6
VCC2(1)
3
GND
7
GND
4
RF IN
8
RF OUT
NOTE(S):
(1)
(2)
All supply pins may be connected together at the supply.
GROUND PAD is package underside.
Figure 13. Typical Case Markings
SKYWORKS
Mark Pin 1
Identifier
CX77105-NN
EXXXXX.XX
YYWW MEX
Manufacturing Part Number-Revision Number
Lot Number
YY = Manufacture Year
WW = Week Package Sealed
MEX = Country Code
101787_006
101787A
December 10, 2002
Skyworks Solutions, Inc. Proprietary
13
CX77105
Package and Handling Information
Power Amplifier Module for CDMA/AMPS (824–849 MHz)
Package and Handling Information
Because of its sensitivity to moisture absorption, this device package is baked and vacuum packed
prior to shipment. Instructions on the shipping container label must be followed regarding exposure
to moisture after the container seal is broken, otherwise, problems related to moisture absorption
may occur when the part is subjected to high temperature during solder assembly.
The CX77105 is capable of withstanding an MSL 3/240 °C solder reflow. Care must be taken when
attaching this product, whether it is done manually or in a production solder reflow environment. If
the part is attached in a reflow oven, the temperature ramp rate should not exceed 5 °C per second;
maximum temperature should not exceed 240 °C. If the part is manually attached, precaution
should be taken to insure that the part is not subjected to temperatures exceeding 240 °C for more
than 10 seconds. For details on both attachment techniques, precautions, and handling procedures
recommended by Skyworks, please refer to Application Note: PCB Design and SMT
Assembly/Rework, Document Number 101752. Additional information on standard SMT reflow profiles
can also be found in the JEDEC Standard J–STD–020B.
Production quantities of this product are shipped in the standard tape-and-reel format. For
packaging details, refer to Application Note: Tape and Reel, Document Number 101568.
14
Skyworks Solutions, Inc. Proprietary
101787A
December 10, 2002
CX77105
Electrostatic Discharge Sensitivity
Power Amplifier Module for CDMA/AMPS (824–849 MHz)
Electrostatic Discharge Sensitivity
The CX77105 is a Class I device. Figure 14 lists the Electrostatic Discharge (ESD) immunity level
for each pin of the CX77105 product. The numbers in Figure 14 specify the ESD threshold level
for each pin where the I-V curve between the pin and ground starts to show degradation. The ESD
testing was performed in compliance with MIL-STD-883E Method 3015.7 using the Human Body
Model. Since 2000 volts represents the maximum measurement limit of the test equipment used,
pins marked > 2000 V pass 2000V ESD stress.
Figure 14. ESD Sensitivity Ares (Top View)
+ 1600 V
VREF
– 1400 V
1
10
GND
+ 1000 V
VCONT
– 1300 V
2
9
GND
GND
3
8
> + 2000 V
RF OUT < – 2000 V
+ 2000 V
– 2000 V RF IN
4
7
GND
6
VCC2
GROUND PAD
+ 2000 V
– 2000 V VCC1
5
> + 2000 V
< – 2000 V
101787_007
Various failure criteria can be utilized when performing ESD testing. Many vendors employ
relaxed ESD failure standards which fail devices only after “the pin fails the electrical specification
limits” or “the pin becomes completely non-functional”. Skyworks employs most stringent criteria,
fails devices as soon as the pin begins to show any degradation on a curve tracer.
To avoid ESD damage, both latent and visible, it is very important that the product assembly and
test areas follow the Class-1 ESD handling precautions listed in Table 7.
Table 7. Precautions for GaAs ICs with ESD Thresholds Greater Than 200 V But Less Than 2000 V
Personnel Grounding
Wrist Straps
Conductive Smocks, Gloves and Finger Cots
Antistatic ID Badges
Facility
Relative Humidity Control and Air Ionizers
Dissipative Floors (less than 109 Ω to GND)
Protective Workstation
Dissipative Table Tops
Protective Test Equipment (Properly Grounded)
Grounded Tip Soldering Irons
Conductive Solder Suckers
Static Sensors
Protective Packaging & Transportation
Bags and Pouches (Faraday Shield)
Protective Tote Boxes (Conductive Static Shielding)
Protective Trays
Grounded Carts
Protective Work Order Holders
101787A
December 10, 2002
Skyworks Solutions, Inc. Proprietary
15
Ordering Information
Model Number
Manufacturing
Part Number
Product Revision
Package
Operating Temperature
CX77105
CX77105-16P
16
4x4LM-10
–30 °C to +85 °C
Revision History
Revision
A
Level
Date
December 10, 2002
Description
Initial Release
References
Application Note: PCB Design and SMT Assembly/Rework, Document Number 101752.
Application Note: Tape and Reel, Document Number 101568
JEDEC Standard J–STD–020B.
© 2001, 2002, Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. ("Skyworks") products. These materials are
provided by Skyworks as a service to its customers and may be used for informational purposes only. Skyworks assumes no
responsibility for errors or omissions in these materials. Skyworks may make changes to its products, specifications and product
descriptions at any time, without notice. Skyworks makes no commitment to update the information and shall have no responsibility
whatsoever for conflicts, incompatibilities, or other difficulties arising from future changes to its products and product descriptions.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as
may be provided in Skyworks' Terms and Conditions of Sale for such products, Skyworks assumes no liability whatsoever.
THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, RELATING
TO SALE AND/OR USE OF SKYWORKS™ PRODUCTS INCLUDING WARRANTIES RELATING TO FITNESS FOR A
PARTICULAR PURPOSE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY PATENT,
COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. SKYWORKS FURTHER DOES NOT WARRANT THE ACCURACY
OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS.
SKYWORKS SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THESE
MATERIALS.
Skyworks™ products are not intended for use in medical, lifesaving or life-sustaining applications. Skyworks' customers using or
selling Skyworks™ products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
The following are trademarks of Skyworks Solutions, Inc.: Skyworks™, the Skyworks symbol, and "Breakthrough Simplicity"™.
Product names or services listed in this publication are for identification purposes only, and may be trademarks of third parties. Thirdparty brands and names are the property of their respective owners.
Additional information, posted at www.skyworksinc.com, is incorporated by reference.
General Information:
Skyworks Solutions, Inc.
4311 Jamboree Rd.
Newport Beach, CA. 92660-3007
www.skyworksinc.com