RADIO FREQUENCY IDENTIFICATION SYSTEMS Tag-itä HF-I Transponder Inlay - Rectangle-Large The Tag-it HF-I Transponder Inlay is compliant with the ISO/IEC 15693 standard. With a user memory of 2k bits, organized in 64 blocks, the Tag-it HF-I Transponder Inlays allows advanced solutions for a variety of applications, including product authentication, ticketing, library management, supply chain management etc. The thin and flexible Tag-it HF-I Transponder Inlays can be easily converted into paper labels. Specifications: Part Number RI-I12-112A Supported Standard ISO 15693-2,-3 Recommended Operating frequency 13.56 MHz Passive Resonance Frequency (at +25°C) 13.86 MHz ± 200kHz (includes frequency offset to compensate further integration into paper) Typ. required activation field strength read (at +25°C) 94 dBµA/m # Typ. required activation field strength write (at +25°C) 97 dBµA/m # Factory programmed Read Only Number 64 bits Memory (user programmable) 2k bits organized in 64 x 32-bit blocks Typical programming cycles (at +25°C) 100,000 Data retention time (at +55°C) > 10 years Simultaneous Identification of Tags Up to 50 tags per second (reader/antenna dependent) Antenna size 45 mm x 76 mm (∼1.77 in x ∼2.99 in) Foil width 48 mm ± 0.5 mm (1.89 in ± 0.02 in) Foil pitch 101.6 mm +0.1mm/-0.4mm (4 in) Thickness Chip: 0.355mm (∼0.014 in) Antenna: 0.085mm (∼0.0033 in) Base material Substrate: PET (Polyethylenetherephtalate) Antenna: Aluminum Smallest bending radius allowed 18 mm (∼0.71 in) Operating temperature -25°C to +70°C Storage temperature (single inlay) -40°C to +85°C (warpage may occur at upper temperature range) Storage temperature (on reel) -40°C to +40°C Delivery Single row tape wound on cardboard reel with 500 mm diameter Reel outer width: approx. 60 mm (∼2.36 in) Reel inner width: approx. 50 mm (∼1.97 in) Hub diameter: 76.2 mm (3 in) Typical quantity of good units per reel 5,000 Note: For highest possible read-out coverage we recommend to operate readers at a modulation depth of 20% or higher # After integration into paper For more information, contact the sales office or distributor nearest you. This contact information can be found on our web site at: http://www.ti-rfid.com Supported Command Set Request ISO 15693 Mandatory and Optional Commands Inventory Stay Quiet Read_Single_Block Write_Single_Block Lock_Block Read_Multi_Blocks Write_Multi_Blocks Select Tag Reset to Ready Write_AFI Lock_AFI Write DSFID Lock DSFID Get_System_info Get_M_Blk_Sec_St TI Custom Commands Write_2_Blocks Lock_2_Blocks Request Mode Request Inventory Addressed NonSelect Code Addressed 0x01 0x02 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 2 0xA2 0xA3 - - - AFI 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 - 2 2 2 2 2 2 - - 2 - - - - - 2 - 2 - 2: Implemented - : Not applicable Memory Organization 32 bits Lock Bits F = Factory Lock, U = User Lock F U Block # 1 2 3 User data (2048 bits) 62 63 64 X DSFID AFI IC Version UID Num ber (64 bits) Application Configuration Factory programmed Texas Instruments reserves the right to change its products and services at any time without notice. TI provides customer assistance in various technical areas, but does not have full access to data concerning the uses and applications of customers products. Therefore, TI assumes no responsibility for customer product design or for infringement of patents and/or the rights of third parties, which may result from assistance provided by TI. © Copyright 2002 Texas Instruments Incorporated. 11-09-22-129 10/02