LTC1864/LTC1865 µPower, 16-Bit, 250ksps 1- and 2-Channel ADCs in MSOP U FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ DESCRIPTIO 16-Bit 250ksps ADCs in MSOP Package Single 5V Supply Low Supply Current: 850µA (Typ) Auto Shutdown Reduces Supply Current to 2µA at 1ksps True Differential Inputs 1-Channel (LTC1864) or 2-Channel (LTC1865) Versions SPI/MICROWIRETM Compatible Serial I/O 16-Bit Upgrade to 12-Bit LTC1286/LTC1298 Pin Compatible with 12-Bit LTC1860/LTC1861 U APPLICATIO S ■ ■ ■ ■ High Speed Data Acquisition Portable or Compact Instrumentation Low Power Battery-Operated Instrumentation Isolated and/or Remote Data Acquisition The LTC®1864/LTC1865 are 16-bit A/D converters that are offered in MSOP and SO-8 packages and operate on a single 5V supply. At 250ksps, the supply current is only 850µA. The supply current drops at lower speeds because the LTC1864/LTC1865 automatically power down between conversions. These 16-bit switched capacitor successive approximation ADCs include sample-and-holds. The LTC1864 has a differential analog input with an adjustable reference pin. The LTC1865 offers a softwareselectable 2-channel MUX and an adjustable reference pin on the MSOP version. The 3-wire, serial I/O, small MSOP or SO-8 package and extremely high sample rate-to-power ratio make these ADCs ideal choices for compact, low power, high speed systems. These ADCs can be used in ratiometric applications or with external references. The high impedance analog inputs and the ability to operate with reduced spans down to 1V full scale, allow direct connection to signal sources in many applications, eliminating the need for external gain stages. , LTC and LT are registered trademarks of Linear Technology Corporation. MICROWIRE is a trademark of National Semiconductor Corporation. U TYPICAL APPLICATIO Supply Current vs Sampling Frequency 1000 Single 5V Supply, 250ksps, 16-Bit Sampling ADC 100 SUPPLY CURRENT (µA) 1µF 5V LTC1864 1 ANALOG INPUT 0V TO 5V VREF VCC 2 IN + SCK 3 IN – SDO GND CONV 4 8 7 6 5 1864 TA01 SERIAL DATA LINK TO ASIC, PLD, MPU, DSP OR SHIFT REGISTERS 10 1 0.1 0.01 0.01 0.1 10 100 1 SAMPLING FREQUENCY (kHz) 1000 1864 TA02 18645f 1 LTC1864/LTC1865 W W W AXI U U ABSOLUTE RATI GS (Notes 1, 2) Supply Voltage (VCC) ................................................. 7V Ground Voltage Difference AGND, DGND LTC1865 MSOP Package ........... ±0.3V Analog Input ............... (GND – 0.3V) to (VCC + 0.3V) Digital Input ................................ (GND – 0.3V) to 7V Digital Output .............. (GND – 0.3V) to (VCC + 0.3V) Power Dissipation .............................................. 400mW Operating Temperature Range LTC1864C/LTC1865C/ LTC1864AC/LTC1865AC ........................ 0°C to 70°C LTC1864I/LTC1865I/ LTC1864AI/LTC1865AI ..................... – 40°C to 85°C Storage Temperature Range ................. – 65°C to 150°C Lead Temperature (Soldering, 10 sec)................. 300°C U U W PACKAGE/ORDER I FOR ATIO ORDER PART NUMBER TOP VIEW TOP VIEW VREF IN + IN¯ GND 1 2 3 4 ORDER PART NUMBER 8 7 6 5 LTC1864CMS8 LTC1864IMS8 LTC1864ACMS8 LTC1864AIMS8 VCC SCK SDO CONV MS8 PACKAGE 8-LEAD PLASTIC MSOP CONV CH0 CH1 AGND DGND LTHQ LTHR VREF 1 8 VCC IN + 2 7 SCK IN – 3 6 SDO GND 4 5 CONV LTVL LTVM LTHS LTHT TJMAX = 150°C, θJA = 175°C/W 1864 1864I CONV 1 8 VCC CH0 2 7 SCK CH1 3 6 SDO GND 4 5 SDI LTC1865CS8 LTC1865IS8 LTC1865ACS8 LTC1865AIS8 S8 PACKAGE 8-LEAD PLASTIC SO S8 PART MARKING S8 PART MARKING TJMAX = 150°C, θJA = 175°C/W 1864A 1864AI LTVN LTVP ORDER PART NUMBER TOP VIEW LTC1864CS8 LTC1864IS8 LTC1864ACS8 LTC1864AIS8 S8 PACKAGE 8-LEAD PLASTIC SO MS PART MARKING TJMAX = 150°C, θJA = 210°C/W ORDER PART NUMBER TOP VIEW LTC1865CMS LTC1865IMS LTC1865ACMS LTC1865AIMS VREF VCC SCK SDO SDI MS PACKAGE 10-LEAD PLASTIC MSOP MS8 PART MARKING TJMAX = 150°C, θJA = 210°C/W 10 9 8 7 6 1 2 3 4 5 1865 1865I 1865A 1865AI Consult LTC Marketing for parts specified with wider operating temperature ranges. W U U CO VERTER A D ULTIPLEXER CHARACTERISTICS The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are TA = 25°C. VCC = 5V, VREF = 5V, fSCK = fSCK(MAX) as defined in Recommended Operating Conditions, unless otherwise noted. PARAMETER Resolution No Missing Codes Resolution INL LTC1864/LTC1865 MIN TYP MAX CONDITIONS (Note 3) ● 16 ● 14 Gain Error 16 15 1.1 ● Bits ±6 1.1 ±20 UNITS Bits ±8 ● Transition Noise LTC1864A/LTC1865A MIN TYP MAX LSB LSBRMS ±20 mV 18645f 2 LTC1864/LTC1865 W U U CO VERTER A D ULTIPLEXER CHARACTERISTICS The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are TA = 25°C. VCC = 5V, VREF = 5V, fSCK = fSCK(MAX) as defined in Recommended Operating Conditions, unless otherwise noted. PARAMETER LTC1864/LTC1865 MIN TYP MAX CONDITIONS Offset Error LTC1864 SO-8 and MSOP, LTC1865 MSOP ● LTC1865 SO-8 ● Input Differential Voltage Range VIN = IN + – IN – Absolute Input Range IN + Input (Note 4) CIN Input Capacitance In Sample Mode During Conversion ±2 ±3 ±5 ±7 mV mV VREF 0 VREF V – 0.05 – 0.05 VCC + 0.05 VCC /2 – 0.05 – 0.05 VCC + 0.05 VCC /2 V V 1 VCC 1 VCC V ±1 µA LTC1864 SO-8 and MSOP, LTC1865 MSOP Analog Input Leakage Current ±5 ±7 UNITS 0 ● IN – Input VREF Input Range ±2 ±3 LTC1864A/LTC1865A MIN TYP MAX ±1 ● 12 5 12 5 pF pF W U DY A IC ACCURACY TA = 25°C. VCC = 5V, VREF = 5V, fSAMPLE = 250kHz, unless otherwise noted. SYMBOL PARAMETER SNR Signal-to-Noise Ratio UNITS 87 dB 10kHz Input Signal 100kHz Input Signal 83 76 dB dB Total Hamonic Distortion Up to 5th Harmonic 10kHz Input Signal 100kHz Input Signal 88 77 dB dB Full Power Bandwidth 20 MHz 125 kHz S/(N + D) Signal-to-Noise Plus Distortion Ratio THD LTC1864/LTC1865 MIN TYP MAX CONDITIONS Full Linear Bandwidth S/(N + D) ≥ 75dB U DIGITAL A D DC ELECTRICAL CHARACTERISTICS The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are TA = 25°C. VCC = 5V, VREF = 5V, unless otherwise noted. LTC1864/LTC1865 MIN TYP MAX SYMBOL PARAMETER CONDITION VIH High Level Input Voltage VCC = 5.25V ● VIL Low Level Input Voltage VCC = 4.75V ● 0.8 V IIH High Level Input Current VIN = VCC ● 2.5 µA IIL Low Level Input Current VIN = 0V ● – 2.5 µA VOH High Level Output Voltage VCC = 4.75V, IO = 10µA VCC = 4.75V, IO = 360µA ● ● VOL Low Level Output Voltage VCC = 4.75V, IO = 1.6mA ● 0.4 V IOZ Hi-Z Output Leakage CONV = VCC ● ±3 µA ISOURCE Output Source Current VOUT = 0V – 25 mA ISINK Output Sink Current VOUT = VCC 20 mA IREF Reference Current (LTC1864 SO-8 and MSOP, LTC1865 MSOP) CONV = VCC fSMPL = fSMPL(MAX) ● ● 0.001 0.05 3 0.1 µA mA ICC Supply Current CONV = VCC After Conversion fSMPL = fSMPL(MAX) ● ● 0.001 0.85 3 1.3 µA mA PD Power Dissipation fSMPL = fSMPL(MAX) 2.4 4.5 2.4 UNITS V 4.74 4.72 4.25 V V mW 18645f 3 LTC1864/LTC1865 U U U U WW RECO E DED OPERATI G CO DITIO S The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are TA = 25°C. SYMBOL PARAMETER LTC1864/LTC1865 MIN TYP MAX CONDITIONS VCC Supply Voltage fSCK Clock Frequency tCYC Total Cycle Time tSMPL Analog Input Sampling Time tsuCONV Setup Time CONV↓ Before First SCK↑ (See Figure 1) thDI Hold Time SDI After SCK↑ tsuDI Setup Time SDI Stable Before SCK↑ tWHCLK SCK High Time fSCK = fSCK(MAX) tWLCLK SCK Low Time fSCK = fSCK(MAX) tWHCONV CONV High Time Between Data Transfer Cycles tWLCONV CONV Low Time During Data Transfer 16 SCK thCONV Hold Time CONV Low After Last SCK↑ 13 ns ● 4.75 5.25 DC 20 UNITS V MHz µs 16 • SCK + tCONV LTC1864 LTC1865 16 14 SCK SCK 30 ns LTC1865 15 ns LTC1865 15 ns 40% 1/fSCK 40% 1/fSCK tCONV µs WU TI I G CHARACTERISTICS The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are TA = 25°C. VCC = 5V, VREF = 5V, fSCK = fSCK(MAX) as defined in Recommended Operating Conditions, unless otherwise noted. LTC1864/LTC1865 MIN TYP MAX SYMBOL PARAMETER tCONV Conversion Time (See Figure 1) ● fSMPL(MAX) Maximum Sampling Frequency ● tdDO Delay Time, SCK↓ to SDO Data Valid CONDITIONS 2.75 kHz 15 20 25 ns ns 30 60 ns 30 60 ns ● tdis Delay Time, CONV↑ to SDO Hi-Z ten Delay Time, CONV↓ to SDO Enabled CLOAD = 20pF ● thDO Time Output Data Remains Valid After SCK↓ CLOAD = 20pF ● tr SDO Rise Time tf SDO Fall Time ● 10 ns CLOAD = 20pF 8 ns CLOAD = 20pF 4 ns Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: All voltage values are with respect to GND. 5 µs 3.2 250 CLOAD = 20pF UNITS Note 3: Integral nonlinearity is defined as deviation of a code from a straight line passing through the actual endpoints of the transfer curve. The deviation is measured from the center of the quantization band. Note 4: Channel leakage current is measured while the part is in sample mode. 18645f 4 LTC1864/LTC1865 U W TYPICAL PERFOR A CE CHARACTERISTICS Supply Current vs Sampling Frequency VCC = 5V TA = 25°C CONV LOW = 800ns 1000 900 10 1 600 400 VCC = 5V VREF = 5V fSAMPLE = 250kHz CONV HIGH = 3.2µS 200 0.1 0.01 0.01 0.1 10 100 1.0 SAMPLING FREQUENCY (kHz) 0 –50 1000 50 0 75 25 TEMPERATURE (°C) –25 1864/65 G01 500 400 300 200 100 0 –50 125 30 20 50 0 75 25 TEMPERATURE (°C) 10 125 100 Reference Current vs Reference Voltage 60 VCC = 5V 54 VREF = 5V f = 250kHz 53 S VCC = 5V TA = 25°C fS = 250kHz 50 REFERENCE CURRENT (µA) 40 –25 1864/65 G03 55 REFERENCE CURRENT (µA) REFERENCE CURRENT (µA) 600 Reference Current vs Temperature VCC = 5V TA = 25°C VREF = 5V CONV LOW = 800ns 50 100 700 1864/65 G02 Reference Current vs Sampling Rate 60 CONV = VCC = 5V 800 800 SUPPLY CURRENT (µA) SUPPLY CURRENT (µA) 100 Sleep Current vs Temperature Supply Current vs Temperature 1000 SLEEP CURRENT (nA) 1000 52 51 50 49 48 47 40 30 20 10 46 0 0 50 100 150 200 SAMPLE RATE (kHz) 0 45 –50 –25 250 50 25 0 75 TEMPERATURE (°C) 1864/65 G04 VCC = 5V TA = 25°C VREF = 5V ANALOG INPUT LEAKAGE (nA) 2 DNL ERROR (LSBs) 1 –2 0 –1 0 16384 32768 CODE 49152 65536 1864/65 G07 1 2 3 VREF (V) –2 0 16384 32768 CODE 5 4 Analog Input Leakage Current vs Temperature 100 2 VCC = 5V TA = 25°C VREF = 5V 0 0 1864/65 G06 Typical DNL Curve 4 INL ERROR (LSBs) 125 1864/65 G05 Typical INL Curve –4 100 49152 65536 VCC = 5V VREF = 5V CONV = 0V 75 50 25 0 –50 –25 0 25 50 75 100 125 TEMPERATURE (°C) 1864/65 G08 1864/65 G09 18645f 5 LTC1864/LTC1865 U W TYPICAL PERFOR A CE CHARACTERISTICS Change in Offset Error vs Reference Voltage 5 20 VCC = 5V 4 VREF = 5V CHANGE IN OFFSET (LSB) VCC = 5V TA = 25°C 50 25 0 VCC = 5V 15 TA = 25°C CHANGE IN GAIN ERROR (LSB) 75 CHANGE IN OFFSET ERROR (LSB) Change in Gain Error vs Reference Voltage Change in Offset vs Temperature 3 2 1 0 –1 –2 –3 1 0 3 4 2 REFERENCE VOLTAGE (V) –5 –50 5 –25 50 0 75 25 TEMPERATURE (°C) 100 5 3 1400 0 –1 800 –2 –3 400 –4 200 729 516 125 0 1 CODE 2 1864/65 G13 SINAD 60 THD (dB) SINAD (dB) 12 0 0 3 4 5 –60 –80 –140 0 50 40 30 VCC = 5V VREF = 5V TA = 25°C VIN = 0dB 10 100 1000 FIN (kHz) 100 –10 90 –20 80 –30 70 –40 60 –50 –60 –90 –100 100 120 50 40 30 VCC = 5V VREF = 5V TA = 25°C VIN = 0dB –80 1 10 100 1000 VCC = 5V VREF = 5V TA = 25°C VIN = 0dB 20 10 0 1 10 100 1000 FIN (kHz) FIN (kHz) 1864/5 G16 40 60 80 FREQUENCY (kHz) SFDR vs Frequency 0 –70 20 20 1864/65 G15 SFDR (dB) SNR 80 10 –20 THD vs Frequency 70 fS = 203.125kHz fIN = 99.72763kHz VCC = 5V VREF = 5V TA = 25°C 1864/65 G14 SINAD vs Frequency 1 0 –120 0 –4 –3 –2 –1 100 5 –100 127 0 0 90 4 2 3 REFERENCE VOLTAGE(V) 1864/65 G12 –40 1000 600 100 1 4096 Point FFT Nonaveraged 1178 1200 1 0 0 AMPLITUDE (dB) 2 50 0 75 25 TEMPERATURE (°C) –10 –20 125 VCC = 5V TA = 25°C VREF = 5V 1534 1600 FREQUENCY CHANGE IN GAIN ERROR (LSB) 1800 VCC = 5V VREF = 5V –25 –5 Histogram of 4096 Conversions of a DC Input Voltage Change in Gain Error vs Temperature –5 –50 0 1864/65 G11 1864/65 G10 4 5 –15 –4 –25 10 1864/5 G17 1864/5 G18 18645f 6 LTC1864/LTC1865 U U U PI FU CTIO S LTC1864 VREF (Pin 1): Reference Input. The reference input defines the span of the A/D converter and must be kept free of noise with respect to GND. IN +, IN– (Pins 2, 3): Analog Inputs. These inputs must be free of noise with respect to GND. GND (Pin 4): Analog Ground. GND should be tied directly to an analog ground plane. CONV (Pin 5): Convert Input. A logic high on this input starts the A/D conversion process. If the CONV input is left high after the A/D conversion is finished, the part powers down. A logic low on this input enables the SDO pin, allowing the data to be shifted out. SDO (Pin 6): Digital Data Output. The A/D conversion result is shifted out of this pin. SCK (Pin 7): Shift Clock Input. This clock synchronizes the serial data transfer. VCC (Pin 8): Positive Supply. This supply must be kept free of noise and ripple by bypassing directly to the analog ground plane. LTC1865 (MSOP Package) CONV (Pin 1): Convert Input. A logic high on this input starts the A/D conversion process. If the CONV input is left high after the A/D conversion is finished, the part powers down. A logic low on this input enables the SDO pin, allowing the data to be shifted out. CH0, CH1 (Pins 2, 3): Analog Inputs. These inputs must be free of noise with respect to AGND. AGND (Pin 4): Analog Ground. AGND should be tied directly to an analog ground plane. DGND (Pin 5): Digital Ground. DGND should be tied directly to an analog ground plane. SDO (Pin 7): Digital Data Output. The A/D conversion result is shifted out of this output. SCK (Pin 8): Shift Clock Input. This clock synchronizes the serial data transfer. VCC (Pin 9): Positive Supply. This supply must be kept free of noise and ripple by bypassing directly to the analog ground plane. VREF (Pin 10): Reference Input. The reference input defines the span of the A/D converter and must be kept free of noise with respect to AGND. SDI (Pin 6): Digital Data Input. The A/D configuration word is shifted into this input. LTC1865 (SO-8 Package) CONV (Pin 1): Convert Input. A logic high on this input starts the A/D conversion process. If the CONV input is left high after the A/D conversion is finished, the part powers down. A logic low on this input enables the SDO pin, allowing the data to be shifted out. CH0, CH1 (Pins 2, 3): Analog Inputs. These inputs must be free of noise with respect to GND. GND (Pin 4): Analog Ground. GND should be tied directly to an analog ground plane. SDI (Pin 5): Digital Data Input. The A/D configuration word is shifted into this input. SDO (Pin 6): Digital Data Output. The A/D conversion result is shifted out of this output. SCK (Pin 7): Shift Clock Input. This clock synchronizes the serial data transfer. VCC (Pin 8): Positive Supply. This supply must be kept free of noise and ripple by bypassing directly to the analog ground plane. VREF is tied internally to this pin. 18645f 7 LTC1864/LTC1865 W FUNCTIONAL BLOCK DIAGRA U CONV (SDI) SCK U VCC PIN NAMES IN PARENTHESES REFER TO LTC1865 CONVERT CLK SDO SERIAL PORT BIAS AND SHUTDOWN DATA IN 16 BITS IN + (CH0) + IN – (CH1) – 16-BIT SAMPLING ADC DATA OUT 1864/65 BD GND VREF TEST CIRCUITS Load Circuit for t dDO, t r, t f, t dis and t en Voltage Waveforms for SDO Rise and Fall Times, t r, t f TEST POINT VOH SDO VOL VCC tdis WAVEFORM 2, ten 3k SDO tdis WAVEFORM 1 20pF tr tf 1864 TC04 1864 TC01 Voltage Waveforms for t en Voltage Waveforms for t dis CONV VIH CONV SDO 1864 TC03 SDO WAVEFORM 1 (SEE NOTE 1) ten 90% tdis Voltage Waveforms for SDO Delay Times, t dDO and t hDO SDO WAVEFORM 2 (SEE NOTE 2) 10% NOTE 1: WAVEFORM 1 IS FOR AN OUTPUT WITH INTERNAL CONDITIONS SUCH THAT THE OUTPUT IS HIGH UNLESS DISABLED BY THE OUTPUT CONTROL NOTE 2: WAVEFORM 2 IS FOR AN OUTPUT WITH INTERNAL CONDITIONS SUCH THAT THE OUTPUT IS LOW UNLESS DISABLED BY THE OUTPUT CONTROL SCK VIL tdDO 1864 TC05 thDO VOH SDO VOL 1864 TC02 18645f 8 LTC1864/LTC1865 U W U U APPLICATIO S I FOR ATIO LTC1864 OPERATION Analog Inputs Operating Sequence The LTC1864 has a unipolar differential analog input. The converter will measure the voltage between the “IN + ” and “IN – ” inputs. A zero code will occur when IN+ minus IN – equals zero. Full scale occurs when IN+ minus IN – equals VREF minus 1LSB. See Figure 2. Both the “IN+ ” and “IN – ” inputs are sampled at the same time, so common mode noise on the inputs is rejected by the ADC. If “IN – ” is grounded and VREF is tied to VCC, a rail-to-rail input span will result on “IN+ ” as shown in Figure 3. The LTC1864 conversion cycle begins with the rising edge of CONV. After a period equal to t CONV, the conversion is finished. If CONV is left high after this time, the LTC1864 goes into sleep mode drawing only leakage current. On the falling edge of CONV, the LTC1864 goes into sample mode and SDO is enabled. SCK synchronizes the data transfer with each bit being transmitted from SDO on the falling SCK edge. The receiving system should capture the data from SDO on the rising edge of SCK. After completing the data transfer, if further SCK clocks are applied with CONV low, SDO will output zeros indefinitely. See Figure 1. Reference Input The voltage on the reference input of the LTC1864 defines the full-scale range of the A/D converter. The LTC1864 can operate with reference voltages from VCC to 1V. CONV t SMPL SLEEP MODE tCONV 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SCK B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0* SDO Hi-Z Hi-Z *AFTER COMPLETING THE DATA TRANSFER, IF FURTHER SCK CLOCKS ARE APPLIED WITH CONV LOW, THE ADC WILL OUTPUT ZEROS INDEFINITELY 1854 F01 Figure 1. LTC1864 Operating Sequence 1µF VCC 1111111111111111 1111111111111110 LTC1864 • • • 1 VIN = 0V TO VCC 0000000000000001 0000000000000000 VIN* VREF VCC 2 IN + SCK 3 IN – SDO GND CONV 4 VREF VREF – 1LSB Figure 2. LTC1864 Transfer Curve VREF – 2LSB 1LSB 0V *VIN = IN + – IN – 8 7 6 5 SERIAL DATA LINK TO ASIC, PLD, MPU, DSP OR SHIFT REGISTERS 1864 F03 1864 F02 Figure 3. LTC1864 with Rail-to-Rail Input Span 18645f 9 LTC1864/LTC1865 U W U U APPLICATIO S I FOR ATIO LTC1865 OPERATION Operating Sequence The LTC1865 conversion cycle begins with the rising edge of CONV. After a period equal to t CONV, the conversion is finished. If CONV is left high after this time, the LTC1865 goes into sleep mode drawing only leakage current. The LTC1865’s 2-bit data word is clocked into the SDI input on the rising edge of SCK after CONV goes low. Additional inputs on the SDI pin are then ignored until the next CONV cycle. The shift clock (SCK) synchronizes the data transfer with each bit being transmitted on the falling SCK edge and captured on the rising SCK edge in both transmitting and receiving systems. The data is transmitted and received simultaneously (full duplex). After completing the data transfer, if further SCK clocks are applied with CONV low, SDO will output zeros indefinitely. See Figure 4. Analog Inputs The two bits of the input word (SDI) assign the MUX configuration for the next requested conversion. For a given channel selection, the converter will measure the voltage between the two channels indicated by the “+” and “–” signs in the selected row of the following table. In single-ended mode, all input channels are measured with respect to GND. A zero code will occur when the “+” input minus the “–” input equals zero. Full scale occurs when the “+” input minus the “–” input equals VREF minus 1LSB. See Figure 5. Both the “+” and “–” inputs are sampled at the same time so common mode noise is rejected. The input span in the SO-8 package is fixed at VREF = VCC. If the “–” input in differential mode is grounded, a rail-to-rail input span will result on the “+” input. Reference Input The reference input of the LTC1865 SO-8 package is internally tied to VCC. The span of the A/D converter is therefore equal to VCC. The voltage on the reference input of the LTC1865 MSOP package defines the span of the A/D converter. The LTC1865 MSOP package can operate with reference voltages from 1V to VCC. Table 1. Multiplexer Channel Selection SINGLE-ENDED MUX MODE DIFFERENTIAL MUX MODE MUX ADDRESS SGL/DIFF ODD/SIGN 0 1 1 1 0 0 1 0 CHANNEL # 0 1 + + + – – + GND – – 1864 TBL1 CONV SDI t SMPL SLEEP MODE tCONV DON’T CARE S/D O/S 1 2 DON’T CARE 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SCK SDO B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0* Hi-Z Hi-Z *AFTER COMPLETING THE DATA TRANSFER, IF FURTHER SCK CLOCKS ARE APPLIED WITH CONV LOW, THE ADC WILL OUTPUT ZEROS INDEFINITELY 1864 F04 Figure 4. LTC1865 Operating Sequence 18645f 10 LTC1864/LTC1865 U W U U APPLICATIO S I FOR ATIO GENERAL ANALOG CONSIDERATIONS Grounding The LTC1864/LTC1865 should be used with an analog ground plane and single point grounding techniques. Do not use wire wrapping techniques to breadboard and evaluate the device. To achieve the optimum performance, use a printed circuit board. The ground pins (AGND and DGND for the LTC1865 MSOP package and GND for the LTC1864 and LTC1865 SO-8 package) should be tied directly to the analog ground plane with minimum lead length. Bypassing For good performance, the VCC and VREF pins must be free of noise and ripple. Any changes in the VCC/VREF voltage with respect to ground during the conversion cycle can induce errors or noise in the output code. Bypass the VCC and VREF pins directly to the analog ground plane with a minimum of 1µF tantalum. Keep the bypass capacitor leads as short as possible. Analog Inputs Because of the capacitive redistribution A/D conversion techniques used, the analog inputs of the LTC1864/ LTC1865 have capacitive switching input current spikes. These current spikes settle quickly and do not cause a problem if source resistances are less than 200Ω or high speed op amps are used (e.g., the LT®1211, LT1469, LT1807, LT1810, LT1630, LT1226 or LT1215). But if large source resistances are used, or if slow settling op amps drive the inputs, take care to ensure the transients caused by the current spikes settle completely before the conversion begins. 1111111111111111 1111111111111110 • • • VIN* 0000000000000001 0000000000000000 VCC VCC – 1LSB VCC – 2LSB 1LSB 0V *VIN = (SELECTED “+” CHANNEL) – (SELECTED “–” CHANNEL) REFER TO TABLE 1 1864 F05 Figure 5. LTC1865 Transfer Curve 18645f 11 12 5VDIG IN – E9 E8 J1 4 1 4 2 3 JP9 3 1 JP8 J2 2 AGND IN + 15V 15V 5 6 5 6 R8 51Ω 0PT IN – R7 51Ω 0PT IN + – + VIN 2 JP3 1 1 1 2 3 4 5 6 7 8 JP2 JP1 RESET CLK P0 P1 P2 P3 ENP GND 2 2 VCC RCO Q0 Q1 Q2 Q3 ENT LO U6 74HC163AD 5VDIG U9A 74AC00 U9B 74AC00 C6 –15V 0.1µF U2 OPT 1 16 15 14 13 12 11 10 9 R2 510Ω R1 510Ω 6 VOUT U1 GND LT1021-5 4 C5 15V 0.1µF C27 0.1µF 2 R3 2Ω 5VDIG 5VDIG C11 390pF C10 680pF OPT C23 0.1µF 1 2 3 4 5 6 7 8 C16 0.1µF RESET CLK P0 P1 P2 P3 ENP GND U13B 74AC32 16 15 14 13 12 11 10 9 C17 0.1µF CLK C24 0.1µF 1 2 3 4 RN1 330 1 R12 10k 5VDIG 1 + V 2 GND 3 SET U10 LTC1799 DIV OUT C18 0.1µF U12B 74AC109 16 14 10 VCC JP4 Q J 13 9 1 Q K 12 CLK 15 CLR 11 8 GND PRE R10 20k 5VDIG ANALOG GROUND PLANE U3 LTC1864CMS8 8 VCC 7 SCK 6 SDO 5 CONV C4 0.1µF 1 V 2 REF IN+ 3 IN– 4 GND 5VAN C12 1000pF OPT 5VDIG VCC RCO Q0 Q1 Q2 Q3 ENT LO U7 74HC163AD 5VDIG C3 10µF 6.3V 1206 C8 1000pF OPT U12A 74AC109 16 6 2 VCC Q J 7 3 Q K 4 CLK 1 CLR 8 5 GND PRE C9 180pF C7 390pF C1 0.1µF C2 1µF 10V 0805 15V 4 5 2 8 7 6 5 VIN 3 2 R4 2Ω 1 C26 10µF 6.3V 1206 U8C 74AC14 U13C 74AC32 3 2 1 U8D 74AC14 JP7 U8B 74AC14 U8A 74AC14 5VDIG C25 5VDIG 0.1µF C22 47pF R6 402Ω 1% C21 47pF R5 402Ω, 1% JP6 VOUT GND 2 5VAN 3 C13 0.1µF U8E 74AC14 16 15 14 13 12 11 10 9 1 2 3 4 5 6 7 8 C14 0.1µF U13D 74AC32 2 JP5 1 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 R9 51Ω CONV J3 E5 E4 E6 CLKIN CLKOUT DOUT DGND E3 ENABLE DATA E7 DGND E2 C15 5VDIG 0.1µF J4 3201S40G1 U9D 74AC00 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 1864/65 AI1 NOTES: UNLESS OTHERWISE SPECIFIED INSTALL SHUNTS ON JP1, JP3-JP7 PIN 1 AND PIN2; ON JP8 AND JP9 PIN 2 AND PIN 4, PIN 3 AND PIN 5. U13A 74AC32 C19 5VDIG 0.1µF U8F 74AC14 U5 74HC595ADT U9C 74AC00 QB VCC QC QA QD A QE OENB QF LCLK QG SCLK RESET QH GND SQH 1 2 3 4 5 6 7 8 5VDIG U4 5VDIG 74HC595ADT 16 QB V 15 CC QC QA 14 QD A 13 QE OENB 12 QF LCLK 11 QG SCLK 10 RESET QH 9 GND SQH 5VDIG U U W E1 APPLICATIO S I FOR ATIO U LTC1864 Evaluation Circuit Schematic LTC1864/LTC1865 18645f LTC1864/LTC1865 U W U U APPLICATIO S I FOR ATIO Component Side Silk Screen for LTC1864 Evaluation Circuit Component Side Showing Traces (Note Wider Traces on Analog Side) Bottom Side Showing Traces (Note Almost No Analog Traces on Board Bottom) Ground Layer with Separate Analog and Digital Grounds Supply Layer with 5V Digital Supply and Analog Ground Repeated 18645f 13 LTC1864/LTC1865 U W U U APPLICATIO S I FOR ATIO U11 15V LT1121CST-5 1 VIN 5VAN C3 10µF 6.3V 1206 VOUT GND 2 R4 2Ω 5VDIG C26 10µF 6.3V 1206 C4 0.1µF 5VDIG 1 V 2 REF IN+ 3 IN– 4 GND 1V to 5V REFERENCE 0V to VREF INPUT 5VAN 3 RN1 330 8 VCC 7 SCK 6 SDO 5 CONV 1 2 3 4 1 RO 2 RE 3 DE 4 DI 8 7 6 5 5VDIG LTC1485 8 VCC 7 B 6 A 5 GND 15V 120Ω U3 LTC1864CMS8 ANALOG GROUND PLANE C23 0.1µF 5VDIG 5VDIG U9A 74AC00 4 1 2 5 3 500Ω 5V MC74VHC1G66 v U12B 74AC109 16 14 10 VCC Q J 13 9 Q K 12 CLK 15 CLR 11 8 GND PRE v U9B 74AC00 C24 0.1µF 5VDIG U12A 74AC109 16 6 2 VCC Q J 7 3 Q K 4 CLK 1 CLR 8 5 GND PRE 4 CONDUCTOR TELEPHONE WIRES TO RECEIVER 5VDIG C16 0.1µF C17 0.1µF 5VDIG 5VDIG 5VDIG 74AC74 RESET CLK P0 P1 P2 P3 ENP GND VCC RCO Q0 Q1 Q2 Q3 ENT LO 16 15 14 13 12 11 10 9 1 2 3 4 5 6 7 8 RESET CLK P0 P1 P2 P3 ENP GND VCC RCO Q0 Q1 Q2 Q3 ENT LO 5VDIG 16 15 14 13 12 11 10 9 C18 0.1µF PRE D CLK CLR U10 LTC1799 100k 1 + V 2 GND 3 SET 74AC86 Q v 1 2 3 4 5 6 7 8 U7 74HC163AD OUT DIV 5 Q 5VDIG 4 74AC74 U13C 74AC32 PRE D CLK CLR Q v U6 74HC163AD Q CLK 1864/65 AI2 U13B 74AC32 Figure 6. LTC1864 Manchester Transmitter 18645f 14 LTC1864/LTC1865 U W U U APPLICATIO S I FOR ATIO Q Q 6 10 12 CLK 11 13 PRE D CLK CLR Q Q 9 8 IC4A 74AC08 4 2 CLK 3 1 PRE D CLK CLR Q Q 5 10 12 CLK 11 13 VCC IC2B 74AC74 PRE D CLK CLR Q 6 Q 9 IC4B 74AC08 8 4 2 CLK 3 1 IC3A 74AC74 PRE D CLK CLR Q v 5 IC6D 74AC32 v PRE D CLK CLR v 4 DATA IN 2 CLK 3 1 IC5C 74AC86 VCC IC1A 74AC74 v VCC VCC IC2A 74AC74 v VCC Q 5 6 IC6C 74LS32D DATA DATA IC1B 74AC74 IC4C 74AC08 VCC IC3B 74AC74 10 12 CLK 11 13 PRE D CLK CLR STROBE Q 8 IC8 74AC595 RECEIVE CLOCK AT 8 X TRANSMIT CLOCK FREQUENCY 14 11 VCC 1 RO 2 RE 3 DE 4 DI VCC 8 VCC 7 B 6 A 5 GND 10 SCK SCL RCK v 12 SER 13 OPTIONAL SERIAL TO PARALLEL CONVERTER VCC 15V SUPPLY TO TRANSMITTER 11 10 IC7B 74AC109 DATA 11 14 12 13 15 PRE J CLK K CLR Q 10 12 13 v R1 120Ω Q QA QB QC QD QE QF QG QH QHIN 15 1 2 3 4 5 6 7 9 D15 D14 D13 D12 D11 D10 D9 D8 15 1 2 3 4 5 6 7 9 D7 D6 D5 D4 D3 D2 D1 D0 IC9 74AC595 14 STROBE 8 SER SCK SCL RCK v U1 LTC1485 4 CONDUCTOR TELEPHONE WIRES TO TRANSMITTER Q 9 v IC4D 74AC08 8 QA QB QC QD QE QF QG QH QHIN 9 1864/65 AI3 Figure 7. LTC1864 Manchester Receiver 18645f 15 LTC1864/LTC1865 U W U U APPLICATIO S I FOR ATIO Transmit LTC1864 Data Over Modular Telephone Wire Using Simple Transmitter/Receiver Figure 6 shows a simple Manchester encoder and differential transmitter suitable for use with the LTC1864. This circuit allows transmission of data over inexpensive telephone wire. This is useful for measuring a remote sensor, particularly when the cost of preserving the analog signal over a long distance is high. Manchester encoding is a clock signal that is modulated by exclusive ORing with the data signal. The resulting signal contains both clock and data information and has an average duty cycle of 50%, that also allows transformer coupling. In practice, generating a Manchester encoded signal with an XOR gate will often produce glitches due to the skew between data and clock transitions. The D flipflops in this encoder retime the clock and data such that the respective edges are closely aligned, effectively suppressing glitches. The retimed data and clock are then XORed to produce the Manchester encoded data, which is interfaced to telephone wire with an LTC1485 RS485 transceiver. In order to synchronize to incoming data, the receiver needs a sequence to indicate the start of a data word. The transmitter schematic shows logic that will produce 31 zeros, a start bit, followed by the 16 data bits (one sample every 48 clock cycles) at a clock frequency of 1MHz set by the LTC1799 oscillator. Sending at least 18 zeros before each start bit ensures that if synchronization is lost, the receiver can resynchronize to a start bit under all conditions. The serial to parallel converter shown in Figure 7 requires 18 zeros to avoid triggering on data bits. The Manchester receiver shown in Figure 7 was adopted from Xilinx application note 17-30 and would typically be implemented in an FPGA. The decoder clock frequency is nominally 8 times the transmit clock frequency and is very tolerant of frequency errors. The outputs of the decoder are data and a strobe that indicates a valid data bit. The data can be deserialized using shift registers as shown. The start bit resets the J-K/flip-flop on its way into the first shift register. When it appears at the QHIN output of the second shift register, it sets the flip-flop that loads the parallel data into the output register. With AC family CMOS logic at 5V the receiver clock frequency is limited to 20MHz; the corresponding transmitter clock frequency is 2.5MHz. If the receiver is implemented in an FPGA that can be clocked at 160MHz, the LTC1864 can be clocked at its rated clock frequency of 20MHz. 18645f 16 LTC1864/LTC1865 U PACKAGE DESCRIPTIO MS8 Package 8-Lead Plastic MSOP (Reference LTC DWG # 05-08-1660) 3.00 ± 0.102 (.118 ± .004) (NOTE 3) 0.889 ± 0.127 (.035 ± .005) 5.23 (.206) MIN 0.42 ± 0.04 (.0165 ± .0015) TYP 3.2 – 3.45 (.126 – .136) 0.65 (.0256) BSC 0.254 (.010) 8 7 6 5 3.00 ± 0.102 (.118 ± .004) NOTE 4 4.88 ± 0.1 (.192 ± .004) DETAIL “A” 0.52 (.206) REF 0° – 6° TYP GAUGE PLANE 0.53 ± 0.015 (.021 ± .006) RECOMMENDED SOLDER PAD LAYOUT DETAIL “A” 1 1.10 (.043) MAX 2 3 4 0.86 (.034) REF 0.18 (.077) SEATING PLANE 0.22 – 0.38 (.009 – .015) 0.65 (.0256) BCS 0.13 ± 0.05 (.005 ± .002) MSOP (MS8) 1001 NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 18645f 17 LTC1864/LTC1865 U PACKAGE DESCRIPTIO MS Package 10-Lead Plastic MSOP (Reference LTC DWG # 05-08-1661) 3.00 ± 0.102 (.118 ± .004) (NOTE 3) 0.889 ± 0.127 (.035 ± .005) 5.23 (.206) MIN 10 9 8 7 6 3.2 – 3.45 (.126 – .136) 0.50 0.305 ± 0.038 (.0197) (.0120 ± .0015) BSC TYP RECOMMENDED SOLDER PAD LAYOUT 0.254 (.010) 3.00 ± 0.102 (.118 ± .004) NOTE 4 4.88 ± 0.10 (.192 ± .004) DETAIL “A” 0.497 ± 0.076 (.0196 ± .003) REF 0° – 6° TYP GAUGE PLANE 1 2 3 4 5 0.53 ± 0.01 (.021 ± .006) DETAIL “A” 0.86 (.034) REF 1.10 (.043) MAX 0.18 (.007) NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX SEATING PLANE 0.17 – 0.27 (.007 – .011) 0.50 (.0197) TYP 0.13 ± 0.05 (.005 ± .002) MSOP (MS) 1001 18645f 18 LTC1864/LTC1865 U PACKAGE DESCRIPTIO S8 Package 8-Lead Plastic Small Outline (Narrow .150 Inch) (Reference LTC DWG # 05-08-1610) 0.189 – 0.197* (4.801 – 5.004) 8 7 6 5 0.150 – 0.157** (3.810 – 3.988) 0.228 – 0.244 (5.791 – 6.197) SO8 1298 1 0.010 – 0.020 × 45° (0.254 – 0.508) 0.008 – 0.010 (0.203 – 0.254) 0.053 – 0.069 (1.346 – 1.752) 0°– 8° TYP 0.016 – 0.050 (0.406 – 1.270) 0.014 – 0.019 (0.355 – 0.483) TYP *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 2 3 4 0.004 – 0.010 (0.101 – 0.254) 0.050 (1.270) BSC 18645f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 19 LTC1864/LTC1865 U TYPICAL APPLICATIO Sample Two Channels Simultaneously with a Single Input ADC 4096 Point FFT of Output 5V 0.1µF f1 (0V TO 0.66V) + 4.096V REF 5k 4.096V REF 100Ω 1/2 LT1492 – 100pF 0.1µF 1µF 0.1µF 1µF 8 VCC 28.7k 5pF 10k 10k 2 1µF 3 0.1µF f2 (0V TO 2V) IN+ IN– 5V 5k + 8 0.1µF 4 1 REF 7 SCK 6 LTC1864 SDO 5 CONV GND 4 100Ω 1/2 LT1492 – AMPLITUDE (dB) 20k 0 10 20 30 40 50 60 70 80 90 100 110 120 130 f1 = 7.507324kHz AT 530mVP-P f2 = 45.007324kHz AT 1.7VP-P fS = 100kHz 0 5 100pF 10 15 20 25 30 35 40 45 50 FREQUENCY (kHz) 1864/65 TA03b 1860 TA03 RELATED PARTS PART NUMBER SAMPLE RATE POWER DISSIPATION DESCRIPTION LTC1417 400ksps 20mW 16-Pin SSOP, Unipolar or Bipolar, Reference, 5V or ±5V LTC1418 200ksps 15mW Serial/Parallel I/O, Internal Reference, 5V or ±5V 200ksps 65mW Configurable Bipolar or Unipolar Input Ranges, 5V 14-Bit Serial I/O ADCs 16-Bit Serial I/O ADCs LTC1609 References LT1460 Micropower Precision Series Reference Bandgap, 130µA Supply Current, 10ppm/°C, Available in SOT-23 LT1790 Micropower Low Dropout Reference 60µA Supply Current, 10ppm/°C, SOT-23 LT1468/LT1469 Single/Dual 90MHz, 16-Bit Accurate Op Amps 22V/µs Slew Rate, 75µV/125µV Offset LT1806/LT1807 Single/Dual 325MHz Low Noise Op Amps 140V/µs Slew Rate, 3.5nV/√Hz Noise, – 80dBc Distortion LT1809/LT1810 Single/Dual 180MHz Low Distortion Op Amps 350V/µs Slew Rate, – 90dBc Distortion at 5MHz Op Amps 18645f 20 Linear Technology Corporation LT/TP 0502 2K • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LINEAR TECHNOLOGY CORPORATION 2001