TSH94 HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER (WITH STANDBY POSITION) . .. .. .. .. . 2 SEPARATE STANDBY : REDUCED CONSUMPTION AND HIGH IMPEDANCE OUTPUTS LOW SUPPLY CURRENT : 4.5mA/amp. typ. HIGH SPEED : 150MHz - 110V/µs UNITY GAIN STABILITY LOW OFFSET VOLTAGE : 3mV LOW NOISE 4.2 nV/√ Hz LOW COST SPECIFIED FOR 600Ω AND 150Ω LOADS HIGH VIDEO PERFORMANCES : Differential Gain : 0.03% Differential Phase : 0.07o Gain Flatness : 6MHz, 0.1dB max. @ 10dB gain HIGH AUDIO PERFORMANCES N DIP16 (Plastic Package) D SO16 (Plastic Micropackage) ORDER CODES Part Number Temperature Range o -40, +125 C TSH94I Package N D • • PIN CONNECTIONS (top view) DESCRIPTION The TSH94 is a quad low power high frequency op-amp, designated for high quality video signal processing. The device offers an excellent speed consumption ratio with 4.5mA/amp. for 150MHz bandwidth. High slew rate and low noise make it also suitable for high quality audio applications. The TSH94 offers 2 separate complementary STANDBY pins : • STANDBY 1 acting on the n° 2 operator • STANDBY 2 acting on the n° 3 operator They reduce the consumption of the corresponding operator and put the output in a high impedance state. November 1998 Output 1 1 Inverting Input 1 2 Non-inve rting Input 1 3 VCC + 4 Non-inve rting Input 2 5 + + 12 Non-inve rting Input 3 Inverting Input 2 6 - - 11 Inverting Input 3 Output 2 7 S ta ndby 1 8 16 Output 4 - - 15 Inverting Input 4 + + 14 Non-inve rting Input 4 13 VCC - 10 Output 3 9 Sta ndby 2 1/12 TSH94 SCHEMATIC DIAGRAM V CC + s tdby s tdby non inverting input Internal Vre f inverting input output Cc s tdby s tdby VCC- ABSOLUTE MAXIMUM RATINGS Symbol VCC Vid Vi Toper Tstg Notes : Parameter Supply Voltage - (note 1) Differential Input Voltage - (note 2) Input Voltage - (note 3) Operating Free Air Temperature Range Storage Temperature Value 14 ±5V -0.3 to 12 -40 to +125 -65 to +150 Unit V V V o C o C 1. All voltage values, except differential voltage are with respect to network ground terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. The magnitude of input and output voltages must never exceed VCC+ +0.3V. OPERATING CONDITIONS Symbol VCC Vicm 2/12 Parameter Supply Voltage Common Mode Input Voltage Range Value 7 to 12 + VCC +2V to VCC -1 Unit V V TSH94 ELECTRICAL CHARACTERISTICS VCC+ = 5V, VCC- = -5V, pin 8 connected to 0V, pin 9 connected to VCC +, Tamb = 25oC (unless otherwise specified) Symbol Parameter Vio Input Offset Voltage (V ic = Vo = 0V) Tmin. ≤ Tamb. ≤ T max. Input Offset Current Iio Tmin. ≤ Tamb. ≤ T max. Input Bias Current Iib Tmin. ≤ Tamb. ≤ T max. Supply Current (per amplifier, no load) ICC Tmin. ≤ Tamb. ≤ T max. CMR Common Mode Rejection Ratio (Vic = -3V to +4V, Vo = 0V) Tmin. ≤ Tamb. ≤ T max. SVR Supply Voltage Rejection Ratio (VCC = ±5V to ±3V) Tmin. ≤ Tamb. ≤ T max. Large Signal Voltage Gain (RL = 10kΩ, VO = ±2.5V) Avd Tmin. ≤ Tamb. ≤ T max. High Level Output Voltage (Vid = 1V) VOH RL = 600Ω RL = 150Ω RL = 150Ω Tmin. ≤ T amb. ≤ Tmax. Low Level Output Voltage (Vid = -1V) VOL RL = 600Ω RL = 150Ω RL = 150Ω Tmin. ≤ T amb. ≤ Tmax. Output Short Circuit Current (Vid = ±1V) Source Io Sink Source Tmin. ≤ Tamb. ≤ T max. Sink GBP Gain Bandwidth Product (AVCL = 100, RL = 600Ω, CL = 15pF, f =7.5MHz) fT Transition Frequency SR Slew Rate (A VCL = +1, RL = 600Ω, CL = 15pF, Vin = -2 to +2V) ∅m Phase Margin (AVM = +1) en VO1/VO2 Gf THD ∆G ∆ϕ Min. Typ. 1 5 4.5 Unit mV µA µA mA 80 70 60 50 57 54 100 dB 75 dB 70 dB 3 2.5 2.4 3.5 3 V V -3.5 -2.8 20 20 15 15 36 40 90 150 90 110 35 -3 -2.5 -2.4 mA MHz 70 Equivalent Input Noise Voltage (Rs = 50Ω, f = 1kHz) 4.2 Channel Separation (f = 1MHz to 10MHz) Gain Flatness (f = DC to 6MHz, AVCL = 10dB) Total Harmonic Distortion (f = 1kHz, Vo = ±2.5V, RL = 600Ω) Differential Gain (f = 3.58MHz, A VCL = +2, RL = 150Ω) 65 Differential Phase (f = 3.58MHz, AVCL = +2, R L = 150Ω) Max. 3 5 2 5 15 20 6 8 0.1 0.01 0.03 0.07 MHz V/µs Degrees nV √ Hz dB dB % % Degree 3/12 TSH94 STANDBY MODE VCC+ = 5V, VCC- = -5V, Tamb = 25oC (unless otherwise specified) Symbol VSBY ICC SBY Isol tON tOFF ID IOL IIL Parameter Pin 8/9 Threshold Voltage for STANDBY Mode Total Consumption Standby 1 & 2 = 0 Standby 1 & 2 = 1 Standby 1 = 1, Standby 2 = 0 Input/Output Isolation (f = 1MHz to 10MHz) Time from Standby Mode to Active Mode Time from Active Mode to Standby Mode Standby Driving Current Output Leakage Current Input Leakage Current LOGIC INPUT Standby 1 Standby 2 0 0 0 1 1 0 1 1 VCC sta ndby 13.7 13.7 9.4 70 200 200 2 20 20 Op-amp 2 Enable Enable Standby Standby STATUS Op-amp 3 Standby Enable Standby Enable 4/12 Max. + VCC -1.0 Unit V mA dB ns ns pA pA pA Op-amp 1 & 4 Enable Enable Enable Enable To put the device in standby, just apply a logic level on the standby MOS input. As ground is a virtual level for the device, threshold voltage has been refered to VCC+ at VCC+ - 1.6V typ. In standby mode, the output goes in high impedance in 200ns. Be aware that all maximum rating must still be followed in this mode. It leads to swing limitation while using the device in signal multiplexing configuration with followers, differential input voltage must not exceed ±5V limiting input swing to 2.5Vpp. APPLICATIONS SIGNAL MULTIPLEXING Typ. + VCC -1.6 STANDBY MODE STANDBY POSITION VCC Min. + VCC -2.2 SAMPLE AND HOLD TSH94 APPLICATIONS VIDEO LINE TRANSCEIVER WITH REMOTE CONTROL PRINTED CIRCUIT LAYOUT As for any high frequency device, a few rules must be observed when designing the PCB to get the best performances from this high speed op amp. From the most to the least important points : • Each power supply lead has to be by-passed to ground with a 10nF ceramic capacitor very close to the device and 10µF capacitor. • To provide low inductance and low resistance common return, use a ground plane or common point return for power and signal. • All leads must be wide and as short as possible especially for op amp inputs. This is in order to decrease parasitic capacitance and inductance. • Use small resistor values to decrease time constant with parasitic capacitance. • Choose componentsizes as small as possible (SMD). • On output, decrease capacitor load so as to avoid circuit stability being degraded which may cause oscillation. You can also add a serial resistor in order to minimise its influence. 5/12 TSH94 INPUT OFFSET VOLTAGE DRIFT VERSUS TEMPERATURE STATIC OPEN LOOP VOLTAGE GAIN LARGE SIGNAL FOLLOWER RESPONSE SMALL SIGNAL FOLLOWER RESPONSE OPEN LOOP FREQUENCY RESPONSE AND PHASE SHIFT CLOSE LOOP FREQUENCY RESPONSE 6/12 TSH94 AUDIO BANDWIDTH FREQUENCY RESPONSE AND PHASE SHIFT (TSH94 vs Standard 15MHz Audio Op-Amp) GAIN FLATNESS AND PHASE SHIFT VERSUS FREQUENCY CROSS TALK ISOLATION VERSUS FREQUENCY (SO16 PACKAGE) CROSS TALK ISOLATION VERSUS FREQUENCY (SO16 PACKAGE) INPUT/OUTPUT ISOLATION IN STANDBY MODE (SO16 PACKAGE) STANDBY SWITCHING 7/12 TSH94 DIFFERENTIAL INPUT IMPEDANCE VERSUS FREQUENCY SIGNAL MULTIPLEXING (cf p. 5/10) 4.5 4.0 3.5 Zin-diff (kΩ) 3.0 2.5 2.0 1.5 1.0 0.5 1k 10k 100k 1M Fre que ncy (Hz) COMMON INPUT IMPEDANCE VERSUS FREQUENCY 120 Zin-com (MΩ) 100 80 60 40 20 1k 10k 100k 1M Frequency (Hz) 8/12 10M 100M 10M 100M TSH94 .. MACROMODEL LOW DISTORTION GAIN BANDWIDTH PRODUCT : 150MHz .. UNITY GAIN STABLE SLEW RATE : 110V/µs Applies to : TSH94,I (model without standby) ** Standard Linear Ics Macromodels, 1996. ** CONNECTIONS : * 1 INVERTING INPUT * 2 NON-INVERTING INPUT * 3 OUTPUT * 4 POSITIVE POWER SUPPLY * 5 NEGATIVE POWER SUPPLY .SUBCKT TSH94 1 3 2 4 5 (analog) ********************************************************** .MODEL MDTH D IS=1E-8 KF=1.809064E-15 CJO=10F * INPUT STAGE CIP 2 5 1.000000E-12 CIN 1 5 1.000000E-12 EIP 10 5 2 5 1 EIN 16 5 1 5 1 RIP 10 11 2.600000E-01 RIN 15 16 2.600000E-01 RIS 11 15 3.645298E-01 DIP 11 12 MDTH 400E-12 DIN 15 14 MDTH 400E-12 VOFP 12 13 DC 0.000000E+00 VOFN 13 14 DC 0 IPOL 13 5 1.000000E-03 CPS 11 15 2.986990E-10 DINN 17 13 MDTH 400E-12 VIN 17 5 2.000000e+00 DINR 15 18 MDTH 400E-12 VIP 4 18 1.000000E+00 FCP 4 5 VOFP 3.500000E+00 FCN 5 4 VOFN 3.500000E+00 FIBP 2 5 VOFP 1.000000E-02 FIBN 5 1 VOFN 1.000000E-02 * AMPLIFYING STAGE FIP 5 19 VOFP 2.530000E+02 FIN 5 19 VOFN 2.530000E+02 RG1 19 5 3.160721E+03 RG2 19 4 3.160721E+03 CC 19 5 2.00000E-09 DOPM 19 22 MDTH 400E-12 DONM 21 19 MDTH 400E-12 HOPM 22 28 VOUT 1.504000E+03 VIPM 28 4 5.000000E+01 HONM 21 27 VOUT 1.400000E+03 VINM 5 27 5.000000E+01 *********************** RZP1 5 80 1E+06 RZP2 4 80 1E+06 GZP 5 82 19 80 2.5E-05 RZP2H 83 4 10000 RZP1H 83 82 80000 RZP2B 84 5 10000 RZP1B 82 84 80000 LZPH 4 83 3.535e-02 LZPB 84 5 3.535e-02 EOUT 26 23 82 5 1 VOUT 23 5 0 ROUT 26 3 35 COUT 3 5 30.000000E-12 DOP 19 25 MDTH 400E-12 VOP 4 25 2.361965E+00 DON 24 19 MDTH 400E-12 VON 24 5 2.361965E+00 .ENDS ELECTRICAL CHARACTERISTICS VCC = ±5V, Tamb = 25oC (unless otherwise specified) Symbol Vio Avd ICC Vicm VOH VOL Isink Isource GBP SR ∅m Conditions RL = 600Ω No load / Ampli RL = 600Ω RL = 600Ω VO = 0V VO = 0V RL = 600Ω, C L = 15pF RL = 600Ω, C L = 15pF RL = 600Ω, C L = 15pF Value 0 3.2 5.2 -3 to 4 +3.6 -3.6 40 40 147 110 42 Unit mV V/mV mA V V V mA mA MHz V/µs Degrees 9/12 TSH94 Applies to : TSH94,I (model with standby) ** Standard Linear Ics Macromodels, 1996. ** CONNECTIONS : * 1 INVERTING INPUT * 2 NON-INVERTING INPUT * 3 OUTPUT * 4 POSITIVE POWER SUPPLY * 5 NEGATIVE POWER SUPPLY * 6 STANDBY .SUBCKT TSH94 1 3 2 4 5 6 (analog) ********************************************************** **************** switch ******************* .SUBCKT SWITCH 20 10 IN OUT COM .MODEL DIDEAL D N=0.1 IS=1E-08 DP IN 1 DIDEAL 400E-12 DN OUT 2 DIDEAL 400E-12 EP 1 OUT COM 10 2 EN 2 IN COM 10 2 RFUIT1 IN 1 1E+09 RFUIT2 OUT 2 1E+09 RCOM COM 0 1E+12 .ENDS SWITCH **************** inverter ***************** .SUBCKT INV 20 10 IN OUT .MODEL DIDEAL D N=0.1 IS=1E-08 RP1 20 15 1E+09 RN1 15 10 1E+09 RIN IN 10 1E+12 RIP IN 20 1E+12 DPINV OUT 20 DIDEAL 400E-12 DNINV 10 OUT DIDEAL 400E-12 GINV 0 OUT IN 15 -6.7E-7 CINV 0 OUT 210f .ENDS INV ***************** AOP ********************** .MODEL MDTH D IS=1E-8 KF=1.809064E-15 CJO=10F * INPUT STAGE CIP 2 5 1.000000E-12 CIN 1 5 1.000000E-12 EIP 10 5 2 5 1 EIN 16 5 1 5 1 RIP 10 11 2.600000E-01 RIN 15 16 2.600000E-01 RIS 11 15 3.645298E-01 DIP 11 12 MDTH 400E-12 DIN 15 14 MDTH 400E-12 VOFP 12 13 DC 0.000000E+00 VOFN 13 14 DC 0 FPOL 13 5 VSTB 1E+03 CPS 11 15 2.986990E-10 DINN 17 13 MDTH 400E-12 VIN 17 5 2.000000e+00 DINR 15 18 MDTH 400E-12 VIP 4 18 1.000000E+00 10/12 FCP 4 5 VOFP 3.500000E+00 FCN 5 4 VOFN 3.500000E+00 ISTB0 4 5 130UA FIBP 2 5 VOFP 1.000000E-02 FIBN 5 1 VOFN 1.000000E-02 * AMPLIFYING STAGE FIP 5 19 VOFP 2.530000E+02 FIN 5 19 VOFN 2.530000E+02 RG1 19 120 3.160721E+03 XCOM1 4 0 120 5 COM SWITCH RG2 19 121 3.160721E+03 XCOM2 4 0 4 121 COM SWITCH CC 19 5 2.00000E-09 DOPM 19 22 MDTH 400E-12 DONM 21 19 MDTH 400E-12 HOPM 22 28 VOUT 1.504000E+03 VIPM 28 4 5.000000E+01 HONM 21 27 VOUT 1.400000E+03 VINM 5 27 5.000000E+01 *********** ZP ********** RZP1 5 80 1E+06 RZP2 4 80 1E+06 GZP 5 82 19 80 2.5E-05 RZP2H 83 4 10000 RZP1H 83 82 80000 RZP2B 84 5 10000 RZP1B 82 84 80000 LZPH 4 83 3.535e-02 LZPB 84 5 3.535e-02 ************************** EOUT 26 23 82 5 1 VOUT 23 5 0 ROUT 26 103 35 COUT 103 5 30.000000E-12 XCOM 4 0 103 3 COM SWITCH DOP 19 25 MDTH 400E-12 VOP 4 25 2.361965E+00 DON 24 19 MDTH 400E-12 VON 24 5 2.361965E+00 ********** STAND BY ******** RMI1 4 111 1E+7 RMI2 0 111 2E+7 RONOFF 6 60 1K CONOGG 60 0 10p RSTBIN 60 0 1E+12 ESTBIN 106 0 6 0 1 ESTBREF 106 107 111 0 1 DSTB1 107 108 MDTH 400E-12 VSTB 108 109 0 ISTB 109 0 1U RSTB 109 110 1 DSTB2 0 110 MDTH 400E-12 XINV 4 0 6 COM INV .ENDS TSH94 PM-DIP16.EPS PACKAGE MECHANICAL DATA 16 PINS - PLASTIC DIP a1 B b b1 D E e e3 F i L Z Min. 0.51 0.77 Millimeters Typ. Max. 1.65 0.5 0.25 Min. 0.020 0.030 Inches Typ. Max. 0.065 0.020 0.010 20 8.5 2.54 17.78 0.787 0.335 0.100 0.700 7.1 5.1 3.3 0.280 0.201 DIP16.TBL Dimensions 0.130 1.27 0.050 11/12 TSH94 PM-SO16.EPS PACKAGE MECHANICAL DATA 16 PINS - PLASTIC MICROPACKAGE (SO) Dimensions Millimeters Typ. 0.1 0.35 0.19 Max. 1.75 0.2 1.6 0.46 0.25 Min. Inches Typ. 0.004 0.014 0.007 0.5 Max. 0.069 0.008 0.063 0.018 0.010 0.020 45o (typ.) 9.8 5.8 10 6.2 0.386 0.228 1.27 8.89 3.8 4.6 0.5 0.394 0.244 0.050 0.350 4.0 5.3 1.27 0.62 0.150 0.181 0.020 0.157 0.209 0.050 0.024 o 8 (max.) SO16.TBL A a1 a2 b b1 C c1 D E e e3 F G L M S Min. 1998 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. http://www.st.com 12/12 ORDER CODE : Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infri ngement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publ ication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for useas critical components inlife support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics