ETC UC3906QTR

UC2906
UC3906
Sealed Lead-Acid Battery Charger
FEATURES
•
•
•
•
DESCRIPTION
Optimum Control for Maximum The UC2906 series of battery charger controllers contains all of the necessary
Battery Capacity and Life
circuitry to optimally control the charge and hold cycle for sealed lead-acid batteries. These integrated circuits monitor and control both the output voltage and curInternal State Logic Provides
rent of the charger through three separate charge states; a high current
Three Charge States
bulk-charge state, a controlled over-charge, and a precision float-charge, or
Precision Reference Tracks
standby, state.
Battery Requirements Over
Optimum charging conditions are maintained over an extended temperature
Temperature
range with an internal reference that tracks the nominal temperature characControls Both Voltage and
teristics of the lead-acid cell. A typical standby supply current requirement of only
Current at Charger Output
1.6mA allows these ICs to predictably monitor ambient temperatures.
•
System Interface Functions
•
Typical Standby Supply
Current of only 1.6mA
Separate voltage loop and current limit amplifiers regulate the output voltage and
current levels in the charger by controlling the onboard driver. The driver will supply up to 25mA of base drive to an external pass device. Voltage and current
sense comparators are used to sense the battery condition and respond with
logic inputs to the charge state logic. A charge enable comparator with a trickle
bias output can be used to implement a low current turn-on mode of the charger,
preventing high current charging during abnormal conditions such as a shorted
battery cell.
Other features include a supply under-voltage sense circuit with a logic output to
indicate when input power is present. In addition the over-charge state of the
charger can be externally monitored and terminated using the over-charge indicate output and over-charge terminate input.
BLOCK DIAGRAM
SLUS186 - SEPTEMBER 1996
Powered by ICminer.com Electronic-Library Service CopyRight 2003
ABSOLUTE MAXIMUM RATINGS (Note 1)
Supply Voltage (+VIN). . . . . . . . . . . . . . . . . . . . . . . . . . . 40V
Open Collector Output Voltages. . . . . . . . . . . . . . . . . . . 40V
Amplifier and Comparator Input Voltages . . . -0.3V to +40V
Over-Charge Terminate Input Voltage . . . . . . -0.3V to +40V
Current Sense Amplifier Output Current . . . . . . . . . . 80mA
Other Open Collector Output Currents. . . . . . . . . . . . 20mA
Trickle Bias Voltage Differential with respect to VIN . . . -32V
Trickle Bias Output Current . . . . . . . . . . . . . . . . . . . . -40mA
Driver Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80mA
Power Dissipation at TA = 25°C(Note 2) . . . . . . . . 1000mW
Power Dissipation at TC = 25°C (Note 2) . . . . . . . . 2000mW
Operating Junction Temperature . . . . . . . . -55°C to +150°C
Storage Temperature . . . . . . . . . . . . . . . . . -65°C to +150°C
Lead Temperature (Soldering, 10 Seconds) . . . . . . . 300°C
Note 1: Voltages are referenced to ground (Pin 6). Currents
are positive into, negative out of, the specified terminals.
Note 2: Consult Packaging section of Databook for thermal
limitations and considerations of packages.
UC2906
UC3906
CONNECTION DIAGRAMS
PLCC-20, LCC-20
(TOP VIEW)
Q, L Packages
PACKAGE PIN FUNCTION
FUNCTION
PIN
N/C
C/S OUT
C/SC/S+
C/L
N/C
+VIN
GROUND
POWER INDICATE
OVER CHARGE
TERMINATE
N/C
OVER CHARGE
INDICATE
STATE LEVEL
CONTROL
TRICKLE BIAS
CHARGE ENABLE
N/C
VOLTAGE SENSE
COMPENSATION
DRIVER SOURCE
DRIVER SINK
DIL-16, SOIC-16 (TOP VIEW)
J or N Package, DW Package
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for TA = -40°C to +70°C for the
UC2906 and 0°C to +70°C for the UC3906, +VIN = 10V, TA = TJ.
PARAMETER
TEST CONDITIONS
UC2906
MIN
UC3906
TYP
MAX
1.6
2.5
MIN
UNITS
TYP
MAX
1.6
2.5
mA
Input Supply
Supply Current
+VIN = 10V
+VIN = 40V
Supply Under-Voltage Threshold +VIN = Low to High
4.2
Supply Under-Voltage Hysteresis
1.8
2.7
4.5
4.8
0.20
0.30
2.3
2.325
3
8
4.2
1.8
2.7
mA
4.5
4.8
V
0.20
0.30
V
2.3
2.330
V
3
8
mV
Internal Reference (VREF)
Voltage Level (Note 3)
Measured as Regulating Level at
Pin 13 w/ Driver Current = 1mA,
TJ = 25°C
Line Regulation
+VIN = 5 to 40V
2.275
Temperature Coefficient
2.270
-3.9
-3.9
mV/°C
Voltage Amplifier
µA
Input Bias Current
Total Input Bias at Regulating Level
-0.5
-0.2
-0.5
-0.2
Maximum Output Current
Source
-45
-30
-15
-45
-30
-15
µA
Sink
30
60
90
30
60
90
µA
Driver current = 1mA
50
65
50
65
Open Loop Gain
dB
Output Voltage Swing
Volts above GND or below +VIN
0.2
0.2
V
Note 3. The reference voltage will change as a function of power dissipation on the die according to the temperature coefficient of
the reference and the thermal resistance, junction-to-ambient.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
2
UC2906
UC3906
ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for TA = -40°C to +70°C for the
UC2906 and 0°C to +70°C for the UC3906, +VIN = 10V, TA = TJ.
PARAMETER
TEST CONDITIONS
UC2906
MIN
UC3906
TYP
MAX
2.0
2.2
MIN
UNITS
TYP
MAX
2.0
2.2
Driver
Minimum Supply to Source
Differential
Pin 16 = +VIN, IO = 10mA
Maximum Output Current
Pin 16 to Pin 15 = 2V
25
Saturation Voltage
40
25
40
V
mA
0.2
0.45
0.2
0.45
V
0.2
1.0
0.2
1.0
µA
Current Limit Amplifier
Input Bias Current
Threshold Voltage
Offset below +VIN
Threshold Supply Sensitivity
+VIN = 5 to 40V
225
250
275
0.03
0.25
225
250
275
mV
0.03
0.25
%/V
Voltage Sense Comparator
Threshold Voltage
As a function of VREF, L1 = RESET
0.945
0.95
0.955
0.945
0.95
0.955
V/V
As a function of VREF, L1 = SET
0.895
0.90
0.905
0.895
0.90
0.905
V/V
Input Bias Current
Total Input Bias at Thresholds
-0.5
-0.2
-0.5
-0.2
µA
Current Sense Comparator
Input Bias Current
Input Offset Current
Input Offset Voltage
Referenced to Pin 2, IOUT = 1mA
Offset Supply Sensitivity
+VIN = 5 to 40V
20
Offset Common Mode Sensitivity CMV = 2V to +VIN
Maximum Output Current
VOUT = 2V
Output Saturation Voltage
IOUT = 10mA
25
0.1
0.5
0.01
0.2
25
30
20
µA
0.1
0.5
0.01
0.2
µA
25
30
mV
0.05
0.35
0.05
0.35
%/V
0.05
0.35
0.05
0.35
%/V
40
25
0.2
0.45
0.99
1.0
1.01
-0.5
25
40
mA
0.2
0.45
V
0.99
1.0
1.01
V/V
-0.2
-0.5
-0.2
µA
40
25
40
mA
Enable Comparator
Threshold Voltage
As a function of VREF
Input Bias Current
Trickle Bias Maximum Output
Current
VOUT = +VIN − 3V
Trickle Bias Maximum Output
Voltage
Volts below +VIN, IOUT = 10mA
Trickle Bias Reverse Hold-Off
Voltage
+VIN = 0V, IOUT = -10µA
2.0
6.3
7.0
0.7
1.0
2.6
2.0
6.3
7.0
0.7
1.0
2.6
V
V
Over-Charge Terminate Input
Threshold Voltage
Internal Pull-Up Current
At Threshold
1.3
10
1.3
V
µA
10
Open Collector Outputs (Pins 7, 9, and 10)
Maximum Output Current
VOUT = 2V
Saturation Voltage
IOUT = 1.6mA
0.25
0.45
0.25
0.45
IOUT = 50µA
0.03
0.05
0.03
0.05
V
VOUT = 40V
1
3
1
3
µA
Leakage Current
Powered by ICminer.com Electronic-Library Service CopyRight 2003
2.5
3
5
2.5
5
mA
V
UC2906
UC3906
the charger a low current turn on mode. The output current of the charger is limited to a low-level until the battery
reaches a specified voltage, preventing a high current
charging if a battery cell is shorted. Figure 2 shows the
state diagram of the charger. Upon turn on the UV sense
circuitry puts the charger in state 1, the high rate bulkcharge state. In this state, once the enable threshold has
been exceeded, the charger will supply a peak current
that is determined by the 250mV offset in the C/L amplifier and the sensing resistor RS.
Internal Reference Temperature Characteristic and
Tolerance
To guarantee full re-charge of the battery, the charger’s
voltage loop has an elevated regulating level, VOC, during
state 1 and state 2. When the battery voltage reaches
95% of VOC, the charger enters the over-charge state,
state 2. The charger stays in this state until the OVERCHARGE TERMINATE pin goes high. In Figure 1, the
charger uses the current sense amplifier to generate this
signal by sensing when the charge current has tapered to
a specified level, IOCT. Alternatively the over-charge could
have been controlled by an external source, such as a
timer, by using the OVER-CHARGE INDICATE signal at
Pin 9. If a load is applied to the battery and begins to discharge it, the charger will contribute its full output to the
load. If the battery drops 10% below the float level, the
charger will reset itself to state 1. When the load is removed a full charge cycle will follow. A graphical representation of a charge, and discharge, cycle of the dual
lever float charger is shown in Figure 3.
OPERATION AND APPLICATION INFORMATION
Dual Level Float Charger Operations
The UC2906 is shown configured as a dual level float
charger in Figure 1. All high currents are handled by the
external PNP pass transistor with the driver supplying
base drive to this device. This scheme uses the TRICKLE
BIAS output and the charge enable comparator to give
Figure 1. The UC2906 in a Dual Level Float Charger
Powered by ICminer.com Electronic-Library Service CopyRight 2003
4
UC2906
UC3906
OPERATION AND APPLICATION INFORMATION (continued)
Design procedure
1.) Pick divider current, ID. Recommended value is
50µA to 100µA.
2.) RC = 2.3V ⁄ ID
3.) RA + RB = RSUM = ( VF − 2.3V )⁄ ID
4.) RD = 2.3VRSUM ⁄ (VOC − VF )
5.) RA = (RSUM + RX ) (1 −2.3V ⁄ VT)
where: RX = RCRD ⁄ (RC + RD)
6.) RB = RSUM − RA
7.) RS = 0.25V ⁄ IMAX
8.) RT = ( VIN − VT − 2.5V ) ⁄ IT
Note:V12 = 0.95VOC
V31 = 0.90VF
IOCT =
IMAX
10
For further design and application information see
UICC Application Note U-104
Figure 2. State Diagram and Design Equations for the Dual Level Float Charger
Explanation: Dual Level Float Charger
output, in this case tied to the OC TERMINATE input,
goes high. The charger changes to the float state and
holds the battery voltage at VF.
F. Here a load (>lMAX) begins to discharge the battery.
G. The load discharges the battery such that the battery
voltage falls below V31. The charger is now in state 1,
again.
A. Input power turns on, battery charges at trickle current rate.
B. Battery voltage reaches VT enabling the driver and turning
off the trickle bias output, battery charges at lMAX rate.
C. Transition voltage V12 is reached and the charger indicates
that it is now in the over-charge state, state 2.
D. Battery voltage approaches the over-charge level VOC and
the charge current begins to taper.
E. Charge current tapers to lOCT. The current sense amplifier
Figure 3. Typical Charge Cycle: UC2906 Dual Level Float Charger
Powered by ICminer.com Electronic-Library Service CopyRight 2003
5
UC2906
UC3906
OPERATION AND APPLICATION INFORMATION (continued)
at the current sense output to prevent excessive power
dissipation on the UC2906.
Compensated Reference Matches Battery Requirements
When the charger is in the float state, the battery will be
maintained at a precise float voltage, VF. The accuracy of
this float state will maximize the standby life of the battery
while the bulk-charge and over-charge states guarantee
rapid and full re-charge. All of the voltage thresholds on
the UC2906 are derived from the internal reference. This
reference has a temperature coefficient that tracks the
temperature characteristic of the optimum-charge and
hold levels for sealed lead-acid cells. This further guarantees that proper charging occurs, even at temperature extremes.
A PNP Pass Device Reduces Minimum Input to Output Differential
The configuration of the driver on the UC2906 allows a
good bit of flexibility when interfacing to an external pass
transistor. The two chargers shown in Figures 1 and 4
both use PNP pass devices, although an NPN device
driven from the source output of the UC2906 driver can
also be used. In situations where the charger must operate with low input to output differentials the PNP pass device should be configured as shown in Figure 4. The PNP
can be operated in a saturated mode with only the series
diode and sense resistor adding to the minimum differential. The series diode, D1, in many applications, can be
eliminated. This diode prevents any discharging of the
battery, except through the sensing divider, when the
charger is attached to the battery with no input supply
voltage. If discharging under this condition must be kept
to an absolute minimum, the sense divider can be referenced to the POWER INDICATE pin, Pin 7, instead of
ground. In this manner the open collector off state of Pin
7 will prevent the divider resistors from discharging the
battery when the input supply is removed.
Dual Step Current Charger Operation
Figures 4, 5 and 6 illustrate the UC2906’s use in a different charging scheme. The dual step current charger is
useful when a large string of series cells must be
charged. The holding-charge state maintains a slightly
elevated voltage across the batteries with the holding current, 1H. This will tend to guarantee equal charge distribution between the cells. The bulk-charge state is similar to
that of the float charger with the exception that when V12
is reached, no over-charge state occurs since Pin 8 is tied
high at all times. The current sense amplifier is used to
regulate the holding current. In some applications a series
resistor, or external buffering transistor, may be required
Figure 4. The UC2906 in a Dual Step Current Charger
Powered by ICminer.com Electronic-Library Service CopyRight 2003
6
UC2906
UC3906
OPERATION AND APPLICATION INFORMATION (continued)
Figure 5. State Diagram and Design Equations for the Dual Step Current Charger
Explanation: Dual Step Current Charger
A. Input power turns on, battery charges at a rate of IH + IMAX.
B. Battery voltage reaches V12 and the voltage loop switches
to the lower level VF. The battery is now fed with the holding
current IH.
C. An external load starts to discharge the battery.
D. When VF is reached the charger will supply the full
current IMAX + IH.
E. The discharge continues and the battery voltage reaches
V21 causing the charger to switch back to state 1.
Figure 6. Typical Charge Cycle: UC2906 Dual Step Current Charger
UNITRODE INTEGRATED CIRCUITS
7 CONTINENTAL BLVD. • MERRIMACK, NH 03054
TEL. 603-424-2410 • FAX 603-424-3460
Powered by ICminer.com Electronic-Library Service CopyRight 2003
7
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1999, Texas Instruments Incorporated
Powered by ICminer.com Electronic-Library Service CopyRight 2003