Revision 4.1 May 23, 2005 Confidential VSC7173 Data Sheet Enhanced 2:1 Port Selector and 1:2 Port Multiplier for Serial ATA and Serial Attached SCSI FEATURES APPLICATIONS 2:1 port selector and 1:2 port multiplier for both Serial ATA (SATA) and Serial Attached SCSI (SAS) links ● Active-passive redundant failover systems ● Dual-port Serial ATA and Serial Attached SCSI disk arrays (JBODs) ● Serial ATA 1.0 compliant at 1.5 Gbps (3.0 Gbps capable) ● NAS servers ● RAID subsystems ● Passes Serial ATA patterns transparently ● Disk-based backup systems ● Programmable receiver sensitivity ● ● High output swing mode with pre-emphasis Serial ATA and Serial Attached SCSI routing applications ● Compatible with VSC7175 and VSC7177 designs ● Buffers for externally connected links ● 0.7 W power dissipation ● Serial ATA port replicators ● 3.3 V power supply ● ● 32-pin, 7 mm x 7 mm QFP-N package Serial ATA Host Bus Adapters selecting between internal and external connectors ● To order the VSC7173 device, see “Ordering Information,” page 17. GENERAL DESCRIPTION The VSC7173 is a Serial ATA and Serial Attached SCSI multiplexer and buffer that implements a 2:1 port selector function for 1.5 Gbps and 3.0 Gbps links. This function is used when dual hosts, such as I/O controllers, must access single-port disk drives in high availability storage subsystems where redundancy and load sharing are important. The outputs from the I/O controllers are multiplexed to a Serial ATA or Serial Attached SCSI drive. The output from the Serial ATA drive is buffered and replicated to the I/O controllers. When switching from one I/O controller to the other, a Serial ATA link must be re-initialized with out-of-band (OOB) signals, which are transferred through the VSC7173 transparently. The VSC7173 provides high output swings with pre-emphasis, and programmable receiver sensitivity that are needed to drive long backplanes and external cables. In addition to the above features, the VSC7173 also supports a 1:2 port multiplier mode where one host can connect two drives. Port connectivity for the device is configured by driving external I/O pins. See the block diagram on page 2. Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 of 17 VSC7173 Data Sheet VSC7173 Block Diagram Port 0 Port 2 P0INP P0INN 0 OOB P2OUTP 1 S En P2OUTN OOBPORT0 0 P0OUTP 1 S En P0OUTN P2INP OOB Port 1 P1INP P1INN OOB 0 P1OUTP P1OUTN 1 S En MODE1 Edge-Triggered Logic 0 P0SLTD S 1 MODE1 PORTSEL0 PORTSEL1 MODE0 OOBSEL [0:1] HIV [0:2] I/O Configuration 2 of 17 Revision 4.1 May 23, 2005 Confidential SET Q RST QN P2INN VSC7173 Data Sheet Application Examples The VSC7173 allows two Serial ATA hosts to access one Serial ATA drive. Figure 1 shows a common application where redundant I/O controllers in disk arrays have multiplexed access to single-port Serial ATA disk drives. VSC7173 I/O Controller A Serial ATA Drive (1 of n) I/O Controller B Backplane "Tailgate" Board Figure 1. Serial ATA Backplane Application Another application example (Figure 2) is for simple port replication to enable an existing Serial ATA Host Bus Adapter (HBA) to connect to two ports. By using the VSC7173, a single channel from the HBA may be selectively connected to an internal connector or an external connector. The VSC7173 provides both the mulitplexing functionality and buffering to drive external connections. Serial ATA Host Bus Adaptor Port A Internal Connector VSC7173 External Connector PCI Bus Port B External Connector Port Multiplier Figure 2. Port Multiplier Application 3 of 17 Confidential Revision 4.1 May 23, 2005 VSC7173 Data Sheet FUNCTIONAL DESCRIPTIONS Modes of Operation Table 1 summarizes the VSC7173 operational mode choices. The mode of the VSC7173 is determined by the following pins. MODE1: Controls whether the selection of port 0 to port 1 is edge-sensitive or level-sensitive. When LOW, port selection is level-sensitive (to enable level-sensitive port selection, pin PORTSEL1 must also be LOW). When HIGH, port selection is edge-sensitive. MODE0: Controls the function of the unselected port. When LOW, the output of this port is turned off. When HIGH, the output of this unselected port is the same data as seen on the selected port. PORTSEL0: In level-sensitive mode (MODE1 is LOW and PORTSEL1 is LOW), controls the selection of port 0 or port 1. When LOW, port 0 is selected; when HIGH, port 1 is selected. In edge-sensitive mode (MODE1 is HIGH), controls the selection of port 0; a rising edge on this pin selects port 0. PORTSEL1: In level-sensitive mode (MODE1 is LOW), must be held LOW. In edge-sensitive mode (MODE1 is HIGH), controls the selection of port 1; a rising edge on this pin selects port 1. Table 1. Port Selection Operating Modes Input Pins High-Speed Connections MODE1 MODE0 PORTSEL0 PORTSEL1 P0OUT P1OUT P2OUT 0 (level) 0 0 0 P2IN OFF P0IN 0 (level) 0 1 0 OFF P2IN P1IN 0 (level) 1 0 0 P2IN P2IN P0IN P1IN 0 (level) 1 1 0 P2IN P2IN 1 (edge) 0 X ↑ OFF P2IN P1IN 1 (edge) 0 ↑ X P2IN OFF P0IN 1 (edge) 1 X ↑ P2IN P2IN P1IN 1 (edge) 1 ↑ X P2IN P2IN P0IN X = don’t care; ↑ = rising. Status Pins Two output pins, P0SLTD and OOBPORT0, are provided for status monitoring. Table 2 summarizes the functionality of these two output pins. OOBPORT0 reports whether the signal on port 0 is above or below the threshold selected in Table 5. P0SLTD, depending on the state of MODE1, can either report which port is selected or can report whether the signal on port 1 is above or below the threshold selected in Table 5. Table 2. Output Status Pins Input Pins Output Status Pins MODE1 PORTSEL0 PORTSEL1 P0SLTD 0 (level) X X OOB status port 1—1 indicates signal is below OOB threshold, 0 indicates signal is above OOB threshold 1 (edge) X ↑ Indicates port selected, 0 = port 1 OOB status port 0 1 (edge) ↑ X Indicates port selected, 1 = port 0 OOB status port 0 X = don’t care; ↑ = rising. 4 of 17 Revision 4.1 May 23, 2005 Confidential OOBPORT0 OOB status port 0—1 indicates signal is below OOB threshold, 0 indicates signal is above OOB threshold VSC7173 Data Sheet Reset State The power-up state of the VSC7173 is based on the PORTSEL0 and PORTSEL1 input signals. When in levelsensitive mode, the active port connected to port 2 is controlled directly by the PORTSEL0 input. This is the same behavior as the normal operating condition described above. When in edge-sensitive mode, the active port connected to port 2 is defined in Table 3. The state diagram in Figure 3 indicates the same result in a different format. Table 3. Power-up State (Edge-Sensitive Mode) PORTSEL0 PORTSEL1 Active Port P0SLTD Output 0 0 Port 0 selected 1 1 0 Port 0 selected 1 0 1 Port 1 selected 0 1 1 Port 0 selected 1 Reset=1 Reset State (PORTSEL0=1, PORTSEL1=1 or PORTSEL1=0) and Reset=0 Reset=1 PORTSEL0=0, PORTSEL1=1 and Reset=0 PORTSEL0 Port 0 Selected Port 1 Selected PORTSEL1 Figure 3. Reset State Machine (Edge-Sensitive Mode) 5 of 17 Confidential Revision 4.1 May 23, 2005 VSC7173 Data Sheet High-Speed Outputs Each port has a high-speed output buffer that transmits the differential serial ATA data at rates up to 3.0 Gbps. The output pins for the ports are P0OUTP/N, P1OUTP/N, and P2OUTP/N. Each output buffer has an input to indicate when OOB signals are being transmitted and a single input to control the output voltage amplitude and to enable preemphasis. Output Data OutputN HIV TX Common Mode Figure 4. High-Speed Output Buffer Transmitting OOB Signals Both differential output signals are at the DC-bias voltage when the output buffer is disabled. The output buffer is disabled when OOB signals are transmitted and when an output port is turned “off.” For more information, see “Functional Descriptions,” page 4. Output Amplitude and Pre-Emphasis Each of the output buffers has an amplitude control input pin, the state of which sets the differential output voltage (within normal SATA levels). Pin HIV0 corresponds to port 0, pin HIV1 corresponds to port 1, and pin HIV2 corresponds to port 2. See Table 4. Recommended output AC-coupling capacitor values are 0.01 µF. When the amplitude control pin is HIGH, the output is configured for high voltage swing mode, which is useful for driving extended length media such as backplanes or external cables. Setting the output to high swing mode should be done only in controlled environments, because the output voltage exceeds the Serial ATA 1.0 differential mode specifications. The output buffers have a pre-emphasis circuit that is enabled when HIVx is HIGH. Pre-emphasis accentuates higher frequency signals in a transmitted data stream. This feature takes into consideration that a signal loses amplitude and affects the data eye opening as it goes through long trace length runs. Figure 5 shows the effects of the pre-emphasis feature. The amplitude increase is between 20% and 30%, and the duration of the amplitude increase is between 150 ps and 300 ps. Table 4. Output Amplitude and Pre-Emphasis HIVx Pin State Output Swing Level Pre-Emphasis 0 Normal None 1 High Enabled 6 of 17 Revision 4.1 May 23, 2005 Confidential VSC7173 Data Sheet Pre-Emphasis Disabled Pre-Emphasis Enabled VOUT VOUT 0 0 1 1 1 1 1 0 1 0 0 0 1 1 1 1 1 0 1 0 Figure 5. Pre-Emphasis Diagram High-Speed Inputs The high-speed input receivers are designed to achieve Serial ATA 1.0 compliance using AC-coupling as described in the Serial ATA 1.0 specification. Recommended input AC-coupling capacitor values are 0.01 µF. The high-speed input receiver contains an OOB signal detector as shown in Figure 6. Input Receiver Input Data InputN OOB Detector OOB Status (OOBPORTx signal) OOBSEL0 OOBSEL1 Figure 6. High-Speed Input Receiver OOB Transfer The VSC7173 cleanly transfers OOB signals from high-speed inputs to outputs. Two status outputs, OOBPORT0 and OOBPORT1, indicate whether the input signal is data or a common-mode state. OOBPORT1 and OOBPORT1 correspond to port 0 and port 1, respectively. An OOB detector monitors the amplitude of an incoming signal in parallel with each high-speed input. When the amplitude is less than the OOB threshold, the OOB status output is driven HIGH. When the incoming amplitude is greater than the OOB threshold, the OOB status output is driven LOW. Setting the OOBSEL1 and OOBSEL0 inputs as shown in the following table configures the OOB threshold level for all three ports. Table 5. Setting the OOB Threshold Level OOBSEL1 OOBSEL0 1 0 OOB THRESHOLD LEVEL Nominal setting (150 mV to 250 mV) 0 0 Decrease by ~40 mV 0 1 Decrease by ~80 mV 1 1 Increase by ~40 mV NOTE: All values are differential peak-to-peak voltages. 7 of 17 Confidential Revision 4.1 May 23, 2005 VSC7173 Data Sheet ELECTRICAL SPECIFICATIONS DC Characteristics Specifications are guaranteed over the recommended operating conditions listed in Table 11. Table 6. LVTTL Inputs and Outputs Symbol Parameter VOH Output HIGH voltage Minimum Typical Maximum Unit Condition 2.0 2.2 VDD V IOH = –4 mA 0.2 IOL = 4 mA VOL Output LOW voltage 0.0 0.4 V VIH Input HIGH voltage 2.0 VDD V VIL Input LOW voltage 0.0 0.8 V II Input current (includes a weak pull-up resistor) –200 +50 µA Maximum Unit Condition See Table 5 on page 7. 0V < VIL < 2.4 V Table 7. High-Speed Inputs and Outputs Symbol Parameter VTH Input threshold voltage for OOB detection 200 mV VOCM High-speed output common-mode voltage 2.0 V Normal Swing mode. 100 Ω termination between true and complement outputs. 1.7 V High Swing mode. 100 Ω termination between true and complement outputs. 1.5 V VICM High-speed input common-mode voltage ZIN Differential input impedance Minimum Typical 85 100 115 Ω Minimum Typical Maximum Unit 3.0 3.3 3.6 V Table 8. Power Supply Requirements Symbol Parameter VDD Power supply voltage IDD Power supply current (total on all supply pins) 150 170 mA Normal Swing mode 200 235 mA High Swing mode Total power dissipation 540 625 mW Normal Swing mode 720 850 mW High Swing mode PD 8 of 17 Revision 4.1 May 23, 2005 Confidential Condition ±10% on all supplies VSC7173 Data Sheet AC Characteristics Specifications are guaranteed over the recommended operating conditions listed in Table 11 on page 11. High-Speed Input tOFF tON High-Speed Output Figure 7. Timing Waveform Table 9. High-Speed Inputs and Outputs Symbol Parameter Minimum Maximum Unit tP Condition Propagation delay from any high-speed input to high-speed output 0.4 2.0 ns tON Propagation delay from signal present at input to output buffer turned on 3.0 12.0 ns tOFF Propagation delay from no signal at input to output buffer turned off 3.0 12.0 ns tR, tF Rise and fall times 67 260 ps VOUT(1) OUTx output differential peak-to-peak voltage swing in normal swing mode (HIVx is LOW) 500 700 mVp-p Measured per Serial ATA 1.0 specification, section 6.6.3. 100 Ω termination between true and complement outputs. VOUT(1, 2) OUTx output differential peak-to-peak voltage swing in high swing mode (HIVx is HIGH) 800 1300 mVp-p Measured per Serial ATA 1.0 specification, section 6.6.3. 100 Ω termination between true and complement outputs. VIN INx input differential peak-to-peak swing with OOBSEL1 = 1 and OOBSEL0 = 0 (OOB nominal) 275 1600 mVp-p Measured per Serial ATA 1.0 specification. VIN INx input differential peak-to-peak swing with OOBSEL1 = 0 and OOBSEL0 = 1 (OOB minimal) 225 1600 mVp-p Measured per Serial ATA 1.0 specification, section 6.6.3. 1.5 Gbps operation, 20% to 80%. 1. Refer to Application Note AN-37 for differential measurement techniques. 2. Output swings are higher than the Serial ATA 1.0 specification to compensate for anticipated PCB or connector losses. 9 of 17 Confidential Revision 4.1 May 23, 2005 VSC7173 Data Sheet tPW tPW PORTSEL0, PORTSEL1 PORTSEL0 tPSS tPSS PORTSEL1 tSW tSW tSW Active Host Port (Port 0 or Port 1) * Edge sensitive sideband operation shown in timing diagram. Note: Edge-sensitive operation shown. Figure 8. Timing Waveform for Port Switching Table 10. Port Switch Timing Symbol Parameter Minimum tPW Pulse width of the port selection pins (PORTSEL0, PORTSEL1). 4.0 ns tPSS Separation between rising edge transitions of the port selection pins. 5.0 ns Edge-sensitive operation tSW Switch time. The time required to make the other host port active following an active edge transition of the port selection pins. ns Applies to both level and edge-sensitive operations 5.0 10 of 17 Revision 4.1 May 23, 2005 Maximum Confidential Unit Condition VSC7173 Data Sheet Operating Conditions Table 11. Recommended Operating Conditions Symbol Parameter VDD Power supply voltage T Operating temperature(1) Minimum Typical Maximum Unit 3.0 3.3 3.6 V +90 °C 0 1. Lower limit of specification is ambient temperature, and upper limit is case temperature. Maximum Ratings Table 12. Absolute Maximum Ratings Symbol Parameter Minimum Maximum Unit VDD Power supply voltage –0.5 +4.0 V VINT LVTTL input voltage –0.5 VDD + 0.5 V VOUTT LVTTL output voltage –0.5 VDD + 0.5 V IOT LVTTL output current –50 +50 mA VINS Serial input voltage –0.5 VDD + 0.5 V VOUTS Serial output voltage –0.5 VDD + 0.5 V IOS Serial output current –50 +50 mA TS Storage temperature –65 +140 °C VESD Electrostatic voltage discharge, human body model –4000 +4000 V Stresses listed under Maximum Ratings may be applied to devices one at a time without causing permanent damage. Functionality at or above the values listed is not implied. Exposure to these values for extended periods may affect device reliability. ELECTROSTATIC DISCHARGE This device can be damaged by ESD. Maxim recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures may adversely affect reliability of the device. 11 of 17 Confidential Revision 4.1 May 23, 2005 VSC7173 Data Sheet PIN DESCRIPTIONS The VSC7173 is packaged in a 32-pin, leadless quad flat pack (QFP-N) with an exposed pad. P0SLTD RESERVED 25 HIV2 27 P2INP P2INN VSS 29 P2OUTN P2OUTP 31 VDD2 Pin Diagram 1 OOBSEL0 HIV0 P0INP 23 3 VSS VSC7173 Top View P0INN VSS 21 5 Pad(1) MODE0 VDD1 15 P1OUTP P1OUTN 13 PORTSEL0 PORTSEL1 17 VSS P1INN HIV1 OOBPORT0 P1INP 11 Exposed Die Attach (bottom side) 9 VDD0 19 7 MODE1 VDD P0OUTN P0OUTP OOBSEL1 1. The exposed Die Attach Pad (DAP) is internally connected to ground and should also be connected to VSS on the board. Figure 9. Pin Diagram 12 of 17 Revision 4.1 May 23, 2005 Confidential VSC7173 Data Sheet Pin Identifications Table 13. Pin Identifications Pin Number Signal Type Level Description O HighSpeed These are the high-speed differential outputs for port 0, port 1, and port 2. These outputs must be AC-coupled. I HighSpeed These are the high-speed differential inputs for port 0, port 1, and port 2. These inputs must be AC-coupled. I LVTTL These two inputs select the active port (port 0 or port 1). For more information on the modes of operation, see Table 1 on page 4. I LVTTL When HIGH, these inputs select the high voltage swing output mode for the corresponding output buffer and enable preemphasis. See Table 4 on page 6. I LVTTL These two inputs control the OOB detector threshold voltage for all three input ports. See Table 5 on page 7 for threshold levels. 7, 6 P0OUTP, P0OUTN 15, 14 P1OUTP, P1OUTN 31, 30 P2OUTP, P2OUTN 3, 4 P0INP, P0INN 11, 12 P1INP, P1INN 27, 28 P2INP, P2INN 19 PORTSEL0 18 PORTSEL1 2 HIV0 10 HIV1 26 HIV2 24 OOBSEL0 23 OOBSEL1 1 P0SLTD O LVTTL This output reports which port is selected or OOB status of port 1, depending on the value of MODE1. See Table 2 on page 4. 9 OOBPORT0 O LVTTL When HIGH, this output indicates that the input signal for port 0 is below the OOB threshold. When LOW, the input signal for port 0 is above the OOB threshold. 17 MODE0 I LVTTL This input is used to select the operating mode for the VSC7173 as described in Table 1 on page 4. 21 MODE1 I LVTTL This input is used to select the operating mode for the VSC7173 as described in Table 1 on page 4. 20 VDD Power 3.3 V power supply for all circuits except the high-speed output buffers. 8, 16 VDD0, VDD1 Power 32 VDD2 3.3 V output buffer power supply for P0OUTP/N, P1OUTP/N, and P2OUTP/N, respectively. 25 Reserved 5, 13, VSS 22, 29 Reserved for future use. Leave unconnected. GND Common ground. DAP is the exposed die attach pad on the bottom of the device. DAP 13 of 17 Confidential Revision 4.1 May 23, 2005 VSC7173 Data Sheet PACKAGE INFORMATION The VSC7173 device is available in a lead(Pb)-free package. VSC7173XYI is a 32-pin leadless quad flat pack (QFP-N) with an exposed pad. Lead(Pb)-free products from Maxim comply with the temperatures and profiles defined in the joint IPC and JEDEC standard IPC/JEDEC J-STD-020. For more information, see the IPC and JEDEC standard. Thermal Specifications Thermal specifications for this device are based on the JEDEC standard EIA/JESD51-2 and have been modeled using a four-layer test board with two signal layers, a power plane, and a ground plane (2s2p PCB). For more information, see the JEDEC standard. Table 14. Thermal Resistances θ JA (°C/W) vs. Airflow (ft/min) Part Number θ JC 0 100 200 VSC7173XYI 18.2 30.0 28.7 27.0 To achieve results similar to the modeled thermal resistance measurements, the guidelines for board design described in the JEDEC standard EIA/JESD51 series must be applied. For information about specific applications, see the following: EIA/JESD51-5, Extension of Thermal Test Board Standards for Packages with Direct Thermal Attachment Mechanisms EIA/JESD51-7, High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages EIA/JESD51-9, Test Boards for Area Array Surface Mount Package Thermal Measurements EIA/JESD51-10, Test Boards for Through-Hole Perimeter Leaded Package Thermal Measurements EIA/JESD51-11, Test Boards for Through-Hole Area Array Leaded Package Thermal Measurement Moisture Sensitivity This device is rated moisture sensitivity level 3 or better as specified in the joint IPC and JEDEC standard IPC/JEDEC J-STD-020. For more information, see the IPC and JEDEC standard. 14 of 17 Revision 4.1 May 23, 2005 Confidential VSC7173 Data Sheet Package Drawing Top View Bottom View D 32 25 24 1 1 0.45 Exposed Pad Area D2 D 17 8 16 9 D2 12° max. A Side View b e A3 A1 L Item Minimum A 0.85 nom. 0.90 A1 0 0.05 A3 b 0.20 REF 0.23 D D2 0.35 7.00 BSC 4.95 e L Maximum 5.25 0.65 BSC 0.50 0.75 NOTES: Drawing not to scale. All units in mm unless otherwise noted. “b” is measured 0.20 to 0.25 from the terminal tip. Figure 10. Package Drawing 15 of 17 Confidential Revision 4.1 May 23, 2005 VSC7173 Data Sheet Recommended Land Pattern A A1 D F A2 E Vias (16 places) C G Stencil Openings (16 places) B Land Pad Detail Item 7 mm x 7 mm x 0.9 mm Exposed Pad QFP-N A 7.445 maximum A1 5.325 minimum A2 4.92 maximum B 0.37 maximum C 1.06 D 4.95 minimum Comments Thermal land dimensions 5.075 typical 5.20 maximum E 5.10 Solder mask opening dimension F 1.0 Stencil opening dimensions G 1.2 Stencil opening and via spacing NOTES: All vias 0.30 to 0.33 diameter, plugged. Drawing not to scale. All dimensions are in mm unless otherwise noted. Figure 11. Recommended Land Pattern 16 of 17 Revision 4.1 May 23, 2005 Confidential VSC7173 Data Sheet ORDERING INFORMATION The VSC7173 device is available in a lead(Pb)-free package. VSC7173XYI is 32-pin leadless quad flat pack (QFP-N) with an exposed pad. Lead(Pb)-free products from Maxim comply with the temperatures and profiles defined in the joint IPC and JEDEC standard IPC/JEDEC J-STD-020. For more information, see the IPC and JEDEC standard. Table 15. VSC7173 Ordering Information Part Number Description VSC7173XYI Lead(Pb)-free 32-pin QFP-N, 7 mm x 7 mm x 0.9 mm body Maxim Integrated Products 120 San Gabriel Drive Sunnyvale, CA 94086 United States 408-737-7600 www.maxim-ic.com Copyright © 2004 to 2005 Maxim Integrated Products Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. Maxim retains the right to make changes to its products or specifications to improve performance, reliability or manufacturability. All information in this document, including descriptions of features, functions, performance, technical specifications and availability, is subject to change without notice at any time. While the information furnished herein is held to be accurate and reliable, no responsibility will be assumed by Maxim for its use. Furthermore, the information contained herein does not convey to the purchaser of microelectronic devices any license under the patent right of any manufacturer. Maxim products are not intended for use in life support products where failure of a Maxim product could reasonably be expected to result in death or personal injury. Anyone using a Maxim product in such an application without express written consent of an officer of Maxim does so at their own risk, and agrees to fully indemnify Maxim for any damages that may result from such use or sale. is a registered trademark of Maxim Integrated Products, Inc. All other products or service names used in this publication are for identification purposes only, and may be trademarks or registered trademarks of their respective companies. All other trademarks or registered trademarks mentioned herein are the property of their respective holders. 17 of 17 Confidential Revision 4.1 May 23, 2005