Agilent HFCT-5710L/LP Small Form Factor Pluggable LC Optical Transceivers Data Sheet Description The HFCT-5710L/LP Small Form Factor Pluggable LC optical transceiver is compliant with both the IEEE 802.3Z (1000BASE-LX) and Small Form Factor Pluggable (SFP) MultiSource Agreement (MSA) specifications. The transceiver is intended for premise, public and access networking equipment. The product transmits data over single mode cable for a link distance of 10 km, which is in excess of the standard. Typical applications for this product are switch to switch, switch backbones, and highspeed interface for server farms. Emerging applications of this product include high-density metro access switch GbE connections. Features • IEEE 802.3Z Gigabit Ethernet (1.25 GBd) 1000BASE-LX compliant • Small Form Factor Pluggable (SFP) Multi-Source Agreement (MSA) compliant • Manufactured in an ISO 9001 compliant facility • Hot-pluggable • HFCT-5710LP bail wire de-latch HFCT-5710L standard de-latch • +3.3 V dc power supply • 1310 nm longwave laser • Eye safety certified: - US 21 CFR(J) - IEC 60825-1 (+All) • LC-Duplex fiber connector compatible • Fiber compatibility: - 2m to 10km with 9µm SM fiber - 2m to 550m with 50µm MM fiber - 2m to 550m with 62.5µm MM fiber Applications • Switch to switch applications • Switched backplane applications • High Speed Interface for server farms • Metro access switch GbE connections Related Products • HFBR-5710L/LP: 850 nm 1.25 GBd 3.3 V multimode SFP Gigabit Ethernet transceiver • HDMP-1687: Quad Channel SerDes IC 1.25 GBd Ethernet • HDMP-1646A: Single Channel SerDes IC for 1.25 GBd Ethernet General Features 1000BASE-LX Compliance: SFP MSA Compliance: The HFCT-5710L/LP is compliant with the IEEE 802.3Z (2000 Edition) Physical Medium Dependent (PMD) sublayer and baseband medium, type 1000BASE-LX (Long Wavelength Laser) description. This includes specifications for the signal coding, optical fiber and connector types, optical and electrical transmitter characteristics, optical and electrical receiver characteristics, jitter characteristics, and compliance testing methodology for the aforementioned. The product package is compliant with the SFP MSA with the LC connector option. The SFP MSA includes specifications for mechanical packaging and performance as well as dc, ac and control signal timing and performance. This transceiver is capable of implementing both Single Mode (SM) and Multimode (MM) optical fiber applications in that order of precedence in the event of conflicting specifications. In addition, the SM link type exceeds the 2 m to 5 km 1000BASE-LX specification by achieving compliance over 2 m to 10 km. The MM link type meets the 50 µm and 62.5 µm MMF specification when used with an “offset launch” fiber. Operating Temperature The HFCT-5710L/LP has an operating case temperature of -10 to +85°C. The power supply is 3.3 V dc. The High Speed I/O (HSIO) signal interface is a Low Voltage Differential type. It is ac coupled and terminated internally to the module. The internal termination is a 100 Ohm differential load. The optical connector is LC duplex. There is no governing environmental specification in IEEE 802.3Z therefore the environmental specifications contained in this product definition take precedence. Compliance over all operating conditions defined in this document is implied except where specifically noted. 1 µH Serial Identification (EEPROM) The HFCT-5710L/LP is compliant with the SFP MSA, which defines the serial identification protocol. This protocol uses the 2-wire serial CMOS E2PROM protocol of the ATMEL AT24C01A or similar. MSA compliant, example contents of the HFCT-5710L/LP serial ID memory are defined in Table 9. Eye Safety For details of product compliance, see Table 1. De-latch Mechanism The de-latching mechanism uses the same design as the MM HFBR-5710L. The HFCT-5710L/ LP is designed with an MSA compliant standard de-latch and an optional de-latch for Belly-toBelly operation. The optional de-latch has been slightly modified outside of MSA compliance to optimize the mechanical performance of the product. These modifications do not interfere with the overall form, fit and function as specified by the SFP MSA. Power Supply Noise The HFCT-5710L/LP can withstand an injection of PSN on the VCC lines of 100 mV ac without a degradation in eye mask margin to 10% on the transmitter and a 1 dB sensitivity penalty on the receiver. This occurs when the product is used in conjunction with the MSA recommended power supply filter shown in Figure 1. VCCT 0.1 µF 1 µH VCCR 3.3 V 0.1 µF SFP MODULE 10 µF HOST BOARD Figure 1 - MSA required power supply filter 2 0.1 µF 10 µF Regulatory Compliance The product meets all of the regulatory compliance listed in Table 1. Table 1 - Regulatory Compliance Feature Test Method Performance Electrostatic Discharge (ESD) to the Electrical Pins Electrostatic Discharge (ESD) to the Duplex LC Receptacle MIL-STD-883C Method 3015 Bellcore GR1089-CORE Class 2 (2000 Volts) 25 kV Air Discharge 10 Zaps at 8 kV (contact discharge) on the electrical faceplate on panel. Electromagnetic Interference (EMI) FCC Class B Applications with high SFP port counts are expected to be compliant; however, margins are dependent on customer board and chassis design. Immunity Variation of IEC 61000-4-3 No measurable effect from a 10 V/m field swept from 80 to 1000 MHz applied to the transceiver without a chassis enclosure. Eye Safety US FDA CDRH AEL Class 1 CDRH certification # 9521220-52 EN (IEC) 60825-1, 2, TUV file # 933/510206/02 EN60950 Class 1 UL file # E173874 Component Recognition Underwriter's Laboratories and Canadian UL file # E173874 Standards Association Joint Component Recognition for Information Technology Equipment Including Electrical Business Equipment 3 Figure 2a. Drawing of SFP Transceiver 4 Figure 2b. SFP host board mechanical layout 5 Figure 2c. 6 Pin-out Table The pin arrangement and definition of this product meets SFP MSA. Table 2 lists the pin description. Table 2 - Pin description Pin Name Function/Description 1 VeeT Transmitter Ground 2 TX Fault Transmitter Fault Indication Note 1 3 TX Disable Transmitter Disable - Module disables on high or open Note 2 4 MOD-DEF2 Module Definition 2 - Two wire serial ID interface Note 3 5 MOD-DEF1 Module Definition 1 - Two wire serial ID interface Note 3 Note 3 6 MOD-DEF0 Module Definition 0 - Grounded in module 7 Rate Select Not Connected 8 LOS Loss of Signal MSA Notes Note 4 9 VeeR Receiver Ground 10 VeeR Receiver Ground 11 VeeR Receiver Ground 12 RD- Inverse Received Data Out Note 5 13 RD+ Received Data Out Note 5 14 VeeR Receiver Ground 15 VccR Receiver Power - 3.3 V ±5% Note 6 16 VccT Transmitter Power - 3.3 V ±5% Note 6 17 VeeT Transmitter Ground 18 TD+ Transmitter Data In Note 7 19 TD- Inverse Transmitter Data In Note 7 20 VeeT Transmitter Ground Notes: 1) TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10K resistor on the host board. Pull up voltage between 2.0V and VccT, R+0.3V. When high, output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V. 2. TX Disable input is used to shut down the laser output per the state table below with an external 4.7 - 10 KW pull-up resistor. Low (0 - 0.8 V): Transmitter on Between (0.8 V and 2.0 V): Undefined High (2.0 - 3.465 V): Transmitter Disabled Open: Transmitter Disabled 3. MOD-DEF 0,1,2. These are the module definition pins. They should be pulled up with a 4.7 - 10 KW resistor on the host board to a supply less than VccT +0.3 V or VccR+0.3 V. MOD-DEF 0 is grounded by the module to indicate that the module is present MOD-DEF 1 is clock line of two wire serial interface for optional serial ID MOD-DEF 2 is data line of two wire serial interface for optional serial ID 4. LOS (Loss of Signal) is an open collector/drain output which should be pulled up externally with a 4.7K - 10 KW resistor on the host board to a supply < VccT,R+0.3 V. When high, this output indicates the received optical power is below the worst case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8 V. 5. RD-/+: These are the differential receiver outputs. They are ac coupled 100W differential lines which should be terminated with 100W differential at the user SERDES. The ac coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines will be between 370 and 1600 mV differential (185 - 800 mV single ended) when properly terminated. 6. VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.135 - 3.465 V at the SFP connector pin. The maximum supply current is 300 mA and the associated inrush current will be no more than 30 mA above steady state after 500 nanoseconds. 7. TD-/+: These are the differential transmitter inputs. They are ac coupled differential lines with 100W differential termination inside the module. The ac coupling is done inside the module and is thus not required on the host board. The inputs will accept differential swings of 500 - 2400 mV (250 1000 mV single ended), though it is recommended that values between 500 and 1200 mV differential (250 - 600 mV single ended) be used for best EMI performance. 7 Table 3 - Absolute Maximum Ratings Absolute maximum ratings are those values beyond which functional performance is not intended, device reliability is not implied, and damage to the device may occur. Parameter Symbol Minimum Maximum Unit Storage Temperature (non-operating) TS -40 +85 °C Relative Humidity RH 5 85 % Supply Voltage VCC -0.5 3.63 V Input Voltage on any Pin VI -0.5 VCC V Notes Table 4 - Recommended Operating Conditions Typical operating conditions are those values for which functional performance and device reliability is implied. Parameter Symbol Minimum Typical Maximum Unit Case Operating Temperature TA -10 +25 +85 °C Supply Voltage VCC 3.14 3.3 3.47 V Notes Table 5 - Transceiver Electrical Characteristics Parameter Symbol Typical Maximum Unit Notes Module supply current ICC Minimum 200 240 mA 1 Power Dissipation PDISS 660 762.3 mW 1 AC Electrical Characteristics Power Supply Noise Rejection (peak - peak) PSNR 100 Inrush Current mV 2 30 mA 3 DC Electrical Characteristics 4 Sense Outputs: Transmit Fault (TX_FAULT) Loss of Signal (LOS) MOD-DEF2 VOH VOL 2.0 VccT, R+0.3 0.8 V V Control Inputs: Transmitter Disable (TX_DISABLE) MOD-DEF1, 2 VIH VIL 2.0 Vcc 0.8 V V VI 500 2000 mV 6 VO Trf 370 1600 400 mV ps 7 Data Input: Transmitter Differential Input Voltage (TD+/-) Data Ouput: Receiver Differential Output Voltage (RD+/-) Receiver Data Rise and Fall Times 4, 5 Notes: 1. Over temperature and Beginning of Life. For end of life, see the Agilent document entitled “Strained Multi Quantum Well (SMQW) Laser Diode (1300nm 9 well), Publication Number: 5988-5952EN. 2. MSA filter is required on host board 10 Hz to 1 MHz. See Figure 1 (Page 2) 3. Satisfied after 500 nanoseconds. Within 500 nanoseconds, maximum of current of 2000 mA and energy of 700 nanojoules 4. LVTTL, External 4.7 - 10 KW Pull-Up Resistor required for TX_FAULT and MOD-DEF 1 and 2. 5. LVTTL, Internal 4.7 - 10 KW Pull-Up Resistor included for TX_Disable 6. Internally ac coupled and terminated (100 Ohm differential) 7. Internally ac coupled and load termination located at the user SERDES 8 Table 6 - Transmitter Optical Characteristics Parameter Symbol Minimum Maximum Unit Notes Output Optical Power (Average) Pout -9.5 -3 dBm Pout -9.5 -3 dBm Pout -9.5 -3 dBm EXR 9 SMF Note 10. 62.5/125 µm NA = 0.2 Note 10. 62.5/125 µm NA = 0.275 IEEE 802.3Z Center Wavelength lC 1270 Optical Extinction Ratio Typical dB 1355 nm Spectral Width - RMS s nm Fig 3 Optical Rise/Fall Time Trise/fall 260 ps RIN12 (OMA), maximum RIN -120 dB/Hz 20% - 80% IEEE 802.3Z IEEE 802.3Z 80 ps IEEE 802.3Z Contributed Total Jitter TJ 0.28 UI IEEE 802.3Z 227 ps IEEE 802.3Z % IEEE 802.3Z Unit Notes IEEE 802.3Z Eye mask margin 10 Table 7 - Receiver Optical Characteristics Parameter Symbol Minimum Typical Maximum Optical Power PIN -3 dBm Receiver Sensitivity PREC -20 dBm At BER of 10-12 Stressed Receiver Sensitivity -14.4 dBm IEEE 802.3Z Notes 8 and 9. Receiver Electrical 3 dB Upper Cutoff Frequency 1500 MHz IEEE 802.3Z 1355 nm Operating Center Wavelength lC Contributed Total Jitter TJ Return Loss (minimum) Loss of Signal - Deasserted (Average) PD Loss of Signal - Asserted (Average) PA Loss of Signal - Hysteresis PD - PA 1270 0.332 UI 12 dB -30 dB -20 0.5 IEEE 802.3Z dB dB Notes: 8. Special pattern - simulates dispersion of fiber. 9. Compliant signal applied. 10. Optical power range based on discussions in Ethernet Committee to ensure required link budget for 10km link. When used with an offset launch patch cord. 9 Table 8 - Transceiver Timing Characteristics Parameter Symbol Tx Disable Assert Time Minimum Typical Maximum Unit t_off 10 µs Tx Disable Negate Time t_on 1 mS Time to initialize, including reset of Tx-Fault t_init 300 mS Tx Fault Assert Time t_fault Tx Disable to Reset t_reset 100 10 Notes 11 IEEE 802.3 12 IEEE 802.3 13 µs 14 µs 15 LOS Assert Time t_loss_on 100 µs 16 LOS Deassert Time t_loss_off 100 µs 17 Serial ID Clock Rate f_serial_ clock 100 KHz Notes: 11. Time from rising edge of Tx Disable to when the optical output falls below 10% of nominal. 12. Time from falling edge of Tx Disable to when the modulated optical output rises above 90% of nominal. 13. From power on or negation of Tx Fault using Tx Disable. 14. Time from fault to Tx fault on. 15. Time Tx Disable must be held high to reset Tx_fault. 16. Time from LOS state to Rx LOS assert. 17. Time from non-LOS state to RX LOS deassert. 5 4.5 RMS spectral width (nm) 4 3.5 3 2.5 2 1.5 Minimum Launched Power -9.5 dBm 1 0.5 0 1270 1280 1290 1300 1310 1320 Wavelength (nm) Figure 3. Tradeoff curves from FC-PI Rev 13 10 1330 1340 1350 1360 Table 9 - EEPROM Serial ID Memory Contents Addr Hex Addr Hex ASCII Addr Hex Addr Hex ASCII 0 03 ASCII 40 48 H 68 Serial # ASCII 96 Note 1 20 1 04 41 46 F 69 Serial # 97 Note 1 20 2 07 42 43 C 70 Serial # 98 Note 1 20 3 00 43 54 T 71 Serial # 99 Note 1 20 4 00 44 2D - 72 Serial # 100 Note 1 20 5 00 45 35 5 73 Serial # 101 Note 1 20 6 02 46 37 7 74 Serial # 102 Note 1 20 7 00 47 31 1 75 Serial # 103 Note 1 20 8 00 48 30 0 76 Serial # 104 Note 1 20 L 9 00 49 4C 77 20 105 Note 1 20 10 00 50 20 78 20 106 Note 1 20 11 01 51 20 79 20 107 Note 1 20 12 0C 52 20 80 20 108 Note 1 20 13 00 53 20 81 20 109 Note 1 20 14 0A 54 20 82 20 110 Note 1 20 15 64 55 20 83 20 111 Note 1 20 16 37 56 20 84 Datecode 112 Note 1 20 17 37 57 20 85 Datecode 113 Note 1 20 18 00 58 20 86 Datecode 114 Note 1 20 19 00 20 41 21 47 G 61 00 89 Datecode 117 Note 1 20 22 49 I 62 00 90 Datecode 118 Note 1 20 23 4C L 63 Checksum 91 Datecode 119 Note 1 20 24 45 E 64 00 92 00 120 Note 1 20 25 4E N 65 1A 93 00 121 Note 1 20 26 54 T 66 00 94 00 122 Note 1 20 27 20 67 00 95 Checksum 123 Note 1 20 28 20 124 Note 1 20 29 20 125 Note 1 20 30 20 126 Note 1 20 31 20 127 Note 1 20 32 20 33 20 34 20 35 20 36 00 37 00 38 30 39 D3 A 59 20 87 Datecode 115 Note 1 20 60 00 88 Datecode 116 Note 1 20 Note 1. These fields are reserved for the future use of Agilent Technologies. 11 www.agilent.com/ semiconductors For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (408) 654-8675 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6271 2451 India, Australia, New Zealand: (+65) 6271 2394 Japan: (+81 3) 3335-8152(Domestic/International), or 0120-61-1280(Domestic Only) Korea: (+65) 6271 2194 Malaysia, Singapore: (+65) 6271 2054 Taiwan: (+65) 6271 2654 Data subject to change. Copyright © 2002 Agilent Technologies, Inc. November 1, 2002 5988-8141EN