LM3661 450mA Subminiature, Micropower Step-Down DC-DC Converter for Ultra Low-Voltage Circuits General Description The LM3661 step-down DC-DC converter is optimized for powering ultra-low voltage circuits from a single Lithium-Ion cell. The device provides two pin-selectable output voltages. See ordering information for a list of voltage options available . This allows adjustment for DSP or CPU voltage options, as well as dynamic output voltage switching for reduced power consumption. Internal synchronous rectification provides high efficiency (92% typ. at 1.35VOUT). The LM3661 offers superior features and performance for mobile phones and similar portable applications. Pinselectable PWM and Linear modes provide improved system control for maximizing battery life. During full-load, fixed frequency PWM operation reduces interference in RF and data acquisition applications by minimizing noise harmonics at sensitive IF and sampling frequencies. The SYNC/MODE input allows synchronization of the switching frequency in a range of below 500 kHz to 750 kHz to prevent noise from intermodulation with system frequencies. Linear operation reduces quiescent current to 29 µA (typ.) during system standby for extended battery life, while supplying up to 15 mA. Shutdown turns the device off and reduces battery consumption to 0.5 µA (typ.). This device offers a selectable over Current Limit to protect a variety of inductors. The LM3661 is available in a 10 pin micro SMD package. This packaging uses National’s chip-scale micro SMD technology and offers the smallest possible size. A high (600 kHz) switching frequency allows use of tiny surface-mount components; only three are required — an inductor and two ceramic capacitors. n ± 3% output voltage precision in PWM mode n Miniature 10-pin micro SMD package n Only three tiny surface-mount external components required n Uses small ceramic capacitors n 8 mV typ. PWM output voltage ripple n Internal synchronous rectification for high efficiency (92% at 2.7 VIN, 1.35 VOUT) n 29 µA typ. quiescent current (Linear mode) n 0.5 µA typ. shutdown current n SYNC/MODE input for frequency synchronization from 500 kHz to 750 kHz n Current and Thermal overload protection n High gain control loop with internal compensation n Up to 450mA IOUT capability for LM3661-1.35/1.4 n Up to TBDmA IOUT capability for LM3661-1.25 Applications n n n n n n Mobile phones Hand-Held radios Personal Digital Assistants Palm-top PC’s and Pocket PC’s Portable Instruments Battery Powered Device Features n Operates from a single Li-ION cell n Pin selectable output voltages n Pin selectable Inductor Current Limit Typical Application Circuit 20098802 © 2005 National Semiconductor Corporation DS200988 www.national.com LM3661 450mA Subminiature, Micropower Step-Down DC-DC Converter for Ultra Low-Voltage Circuits May 2005 LM3661 Block Diagram 20098801 FIGURE 1. Simplified Functional Diagram www.national.com 2 LM3661 Connection Diagrams 10-Bump micro SMD Package 20098804 20098805 Top View Bottom View Ordering Information Order Number Output Voltage LM3661TLX - 1.25 1.05V/1.25V LM3661TL - 1.25 LM3661TLX - 1.35 Package NSC Package Marking 10Bump Wafer Level Chip Scale (micro SMD) SHVB 3000 Units, Tape and Reel SHVB 250 Units, Tape and Reel SDYB 3000 Units, Tape and Reel SDYB 250 Units, Tape and Reel SHCB 3000 Units, Tape and Reel SHCB 250 Units, Tape and Reel 1.05V/1.35V LM3661TL - 1.35 LM3661TLX - 1.40 1.05V/1.40V LM3661TL - 1.40 Supplied As Pin Description Pin Number Name Function A1 FB Feedback Analog Input. Connect to the output at the output filter capacitor (see Typical Application Circuit) B1 VSEL Output Voltage Selection Input. Set this digital input to select the desired output voltage. Set: • VSEL = high programmed ouput voltage • VSEL = low for low programmed output voltage C1 ISEL ISEL = High ( > 1.2V) for set current limit to low value ISEL = Low (GND) for set current limit to high value D1 SYNC/MODE Synchronization Input. Use this digital input for frequency selection or modulation control. Set: • SYNC/MODE = high for low-noise 600 kHz PWM mode • SYNC/MODE = low for micropower linear mode • SYNC/MODE = a 500 kHz -750 kHz external oscillator for synchronization to an external clock in PWM mode. The LM3661 synchronizes with the rising edge of the external clock. D2 EN Enable Input. It has an internal pull down resistor of 1 Mohms. Set this digital input high for normal operation. For shutdown, set low. D3 PGND Power Ground C3 SW Switching Node connection to the internal PFET switch and NFET synchronous rectifier. Connect to an inductor with a saturation current rating that exceeds the peak current limit. B3 PVIN Power Supply Input to the internal PFET switch. Connect to the input filter capacitor (See Typical Application Circuit). 3 www.national.com LM3661 Pin Description Pin Number (Continued) Name Function A3 VDD Analog Supply Input. A2 SGND Analog and Control Ground. www.national.com 4 Storage Temperature Range If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Lead Temperature (Soldering, 10 sec.) Supply Voltage PVIN, VDD to SGND Input Voltage Range FB, ISEL, SW 2.7V to 5.5V Operating Temperature −0.2V to +0.2V EN, SYNC/MODE, VSEL to SGND 260˚C Operating Ratings −0.2V to +6V PGND to SGND −45˚C to 150˚C -30˚C to 85˚C Junction Temperature (Note 3) −30˚C to +125˚C Minimum ESD Rating −0.2V to +6V (Human Body Model, C = 100 pF, R = 1.5 kΩ) −0.2V to (VDD +0.2V) ± 2 kV Thermal properties Thermal Resistance (θJA) 170˚C/W Electrical Characteristics (Note 2) Specifications with standard typeface are for TJ = 25˚C, and those in bold face type apply over the full Operating Temperature Range (TA = TJ = −30˚C to +85˚C). Unless otherwise specified, PVIN = VDD = EN = SYNC/MODE = VSEL = 3.6V, ISEL= 0V, COUT = 22 µF. Symbol VFB, PWM VFB, LINEAR VOVP Parameter Feedback Voltage, PWM Mode VIN = 2.7V to 5.5V Feedback Voltage, Linear Mode VIN= 2.7V to 5.5V, IOUT = 1mA Min Typ Max Units LM3661TL-1.25, VSEL = 0 Remarks 1.019 1.05 1.082 V LM3661TL-1.25, VSEL= VIN 1.213 1.25 1.288 V LM3661TL-1.35, VSEL = 0 1.019 1.05 1.082 V LM3661TL-1.35, VSEL = VIN 1.310 1.35 1.391 V LM3661TL-1.40, VSEL = 0 1.019 1.05 1.082 V LM3661TL-1.40, VSEL = VIN 1.358 1.40 1.442 V LM3661TL-1.25, VSEL = 0 0.998 1.05 1.103 V LM3661TL-1.25, VSEL= VIN 1.188 1.25 1.313 V LM3661TL-1.35, VSEL = 0 0.998 1.05 1.103 V LM3661TL-1.35, VSEL = VIN 1.283 1.35 1.418 V LM3661TL-1.4, VSEL= 0 0.998 1.05 1.103 V LM3661TL-1.4, VSEL= VIN 1.33 1.4 1.47 V 64 90 mV 70 90 mV 5 µA OVP Comparator Hysteresis Voltage (Note 5) SYNC/MODE = VIN VIN = 2.7V to 5.5V OVP Trip point SYNC/MODE = VIN VIN = 3.6V ISHDN Shutdown Supply Current EN = 0V 0.5 IQ,PWM DC Bias Current into VDD (VOUT set to 1.35V) PWM mode, no switching (SYNC/MODE = VDD, VFB =2V) 425 IQ,LIN DC Bias Current into VDD No-Load, Linear mode (SYNC/MODE = 0V) 29 50 µA 40 µA RDSON(P) Pin-pin Resistance for PFET 250 mΩ RDSON(N) Pin-pin Resistance for NFET 180 mΩ Ilim_-1.25 Switch Peak Current Limit Ilim_-1.35/-1.4 Switch Peak Current Limit PWM mode ISEL=VIN, VIN = 2.7V to 4.5V TBD 454 TBD mA PWM mode ISEL = 0, VIN = 2.7V to 4.5V TBD TBD TBD mA PWM mode ISEL=VIN, VIN = 2.7V to 4.5V 473 518 550 mA 565 615 650 mA 35 60 90 mA PWM mode ISEL = 0, VIN = 2.7V to 4.5V Ilim_LIN Max Current in Linear Mode SYNC/MODE = 0V, FB = 0V VIN = 2.7V to 5.5V 5 www.national.com LM3661 Absolute Maximum Ratings (Note 1) LM3661 Electrical Characteristics (Note 2) (Continued) Specifications with standard typeface are for TJ = 25˚C, and those in bold face type apply over the full Operating Temperature Range (TA = TJ = −30˚C to +85˚C). Unless otherwise specified, PVIN = VDD = EN = SYNC/MODE = VSEL = 3.6V, ISEL= 0V, COUT = 22 µF. Symbol Parameter VEN,H EN Logic High Input (Note 4) VEN,L EN Logic Low Input VSYNC/MODE, SYNC/MODE Logic High Input Remarks Min Typ VIN = 2.7V to 5.5V Max Units 1.2 V 0.4 V 1.2 V H VSYNC/MODE, SYNC/MODE Logic Low Input 0.4 V L VSEL, H VSEL Logic High Input VSEL, L VSEL Logic Low Input 1.2 0.4 ISEL,H ISEL Logic High Input ISEL, L ISEL Logic Low Input REN Enable pin input resistance fSYNC SYNC/MODE Clock Frequency Range (Note 6) VIN = 2.7V to 5.5V fOSC Internal Oscillator Frequency PWM mode (SYNC/MODE = VIN) VIN = 2.7V to 5.5V V V 1.2 V 0.4 1 500 535 600 MΩ 750 kHz 675 kHz Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under which operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. Note 2: Min and Max limits are guaranteed by design, test, or statistical analysis. Typical numbers are not guaranteed, but do represent the most likely norm. Due to the pulsed nature of the testing TA=TJ for the electrical characteristics table. Note 3: Thermal shutdown will occur if the junction temperature exceeds 150˚C. This function is only active in PWM mode. Note 4: The LM3202 is designed for mobile phone applications where turn-on after power-up is controlled by the system controller and where requirements for a small package size overrule increased die size for internal Under Voltage Lock-Out (UVLO) circuitry. Thus, it should be kept in shutdown by holding the EN pin low until the input voltage exceeds 2.7V. Note 5: The hysteresis voltage is the minimum voltage swing on FB that causes the internal feedback and control circuitry to turn the internal PFET switch on and then off, during test mode. Note 6: SYNC/MODE driven with an external clock switching between VIN and GND. When an external clock is present at SYNC/MODE, the IC is forced to PWM mode at the external clock frequency. www.national.com 6 (Circuit in Fig.2, PVIN = VDD = EN=3.6V, TA = 25˚C, unless Quiescent Supply Current vs. Supply Voltage (PWM MODE) Quiescent Supply Current vs. Supply Voltage (LDO MODE) 20098810 20098811 Output Voltage vs. Output Current (PWM MODE, ISEL=L, VOUT = 1.35V) Output Voltage vs. Output Current (PWM MODE, ISEL=L, VOUT = 1.05V) 20098814 20098815 Output Voltage vs. Output Current (LDO MODE, VOUT=1.35V) Output Voltage vs. Output Current (LDO MODE, VOUT=1.05V) 20098816 20098817 7 www.national.com LM3661 Typical Performance Characteristics otherwise noted) LM3661 Typical Performance Characteristics (Circuit in Fig.2, PVIN = VDD = EN=3.6V, TA = 25˚C, unless otherwise noted) (Continued) Output Voltage vs. Supply Voltage (PWM MODE, ISEL = L, VOUT = 1.05V) Output Voltage vs. Supply Voltage (PWM MODE, ISEL = L, VOUT = 1.35V) 20098818 20098819 Output Voltage vs. Supply Voltage (LDO MODE, VOUT = 1.35V ) Output Voltage vs. Supply Voltage (LDO MODE, VOUT = 1.05V) 20098848 20098849 Efficiency vs. Output Current (SYNC/MODE = VIN, VOUT = 1.05V) Switching Frequency vs. Temperature (PWM MODE, SYNC/MODE = VIN) 20098822 20098821 www.national.com 8 Efficiency vs. Output Current (PWM MODE, ISEL = L, VOUT = 1.35V) PWM Load Transient Response (ISEL=L, VIN = 3.6V, VOUT = 1.35V) 20098824 20098823 LDO Load Transient Response (VIN = 3.6V & VOUT = 1.35V) PWM Line Transient Response 20098838 20098839 PWM Start-up Respsonse (VIN = 3.6V & VOUT = 1.35V) PWM Start-up Respsonse (VIN = 3.6V & VOUT = 1.05V) 20098825 20098826 9 www.national.com LM3661 Typical Performance Characteristics (Circuit in Fig.2, PVIN = VDD = EN=3.6V, TA = 25˚C, unless otherwise noted) (Continued) LM3661 Typical Performance Characteristics (Circuit in Fig.2, PVIN = VDD = EN=3.6V, TA = 25˚C, unless otherwise noted) (Continued) LDO Start-up Respsonse (VIN = 3.6V & VOUT = 1.05V) LDO Start-up Respsonse (VIN = 3.6V & VOUT = 1.35V) 20098842 20098843 VSEL Transition in PWM Mode (LM3661-1.35) VSEL Transition in LDO Mode (LM3661-1.35) 20098847 20098827 TYP Waveform (PWM Mode, IOUT = 100mA) VSEL & SYNC/MODE Transition in PWM Mode 20098828 20098829 www.national.com 10 TYP Waveform (PWM Mode, IOUT = 450mA) External SYNC/MODE at 600kHz ( IOUT = 100mA) 20098830 20098831 External SYNC/MODE at 600kHz ( IOUT = 450mA ) 20098832 11 www.national.com LM3661 Typical Performance Characteristics (Circuit in Fig.2, PVIN = VDD = EN=3.6V, TA = 25˚C, unless otherwise noted) (Continued) LM3661 the inductor’ magnetic field collapse, generating a voltage that forces current from ground through the synchronous rectifier to the output filter capacitor and load. As the stored energy is transferred back into the circuit and depleted, the inductor current ramps down with a slope of VOUT/L. If the inductor current reaches zero before the next cycle, the synchronous rectifier is turned off to prevent current reversal. The output filter capacitor stores charge when the inductor current is high, and release it when low, smoothing the voltage across the load. Circuit Operation The LM3661 operates as follows: During the first part of each switching cycle, the control block in the LM3661 turns on the internal PFET switch. This allows current to flow from the input through the inductor to the output filter capacitor and load. The inductor limits the current to a ramp with the slope of (VIN − VOUT)/L, by storing energy in a magnetic field. During the second part of each cycle, the controller turns the PFET switch off, blocking current flow from the input, and then turns the NFET synchronous rectifier on. In response, 20098803 FIGURE 2. Typical Operating Circuit PWM Operation LDO Operation The LM3661 can be set to current-mode PWM operation by connecting the SYNC/MODE pin to VDD. While in PWM (Pulse Width Modulation) mode, the output voltage is regulated by switching at a constant frequency and then modulating the energy per cycle to control power to the load. Energy per cycle is set by modulating the PFET switch on-time pulse-width to control the peak inductor current. This is done by controlling the PFET switch using a flip-flop driven by an oscillator and a comparator that compares a ramp from the current-sense amplifier with an error signal from a voltage-feedback error amplifier. At the beginning of each cycle, the oscillator sets the flip-flop and turns on the PFET switch, causing the inductor current to ramp up. When the current sense signal ramps past the error amplifier signal, the PWM comparator resets the flip-flop and turns off the PFET switch, ending the first part of the cycle. The NFET synchronous rectifier turns on until the next clock pulse or the inductor current ramps to zero. If an increase in load pulls the output voltage down, the error amplifier output increases, which allows the inductor current to ramp higher before the comparator turns off the PFET switch. This increases the average current sent to the output and adjusts for the increase in the load. Before going to the PWM comparator, the current sense signal is summed with a slope compensation ramp from the oscillator for stability of the current feedback loop. During the second part of the cycle, a zero crossing detector turns off the NFET synchronous rectifier if the inductor current ramps to zero. Connecting the SYNC/MODE pin to GND sets the LM3661 in Linear Mode operation. While in Linear mode (LDO) the device consumes only 29 µA (typ.) quiescent current for system standby operation. It is capable of delivering up to 15 mA. This is done by using an internal pass transistor and an error amplifier to sense the output voltage and maintain the desire output voltage. During LDO mode, the PFET and NFET of the network switch off to reduce quiescent current. www.national.com Frequency Synchronization The SYNC/MODE input can also be used for frequency synchronization. To synchronize the LM3661 to an external clock, supply a digital signal to the SYNC/MODE pin with a voltage swing exceeding 0.4V to 1.2V. During synchronization, the LM3661 initiates cycles on the rising edge of the clock. When synchronized to an external clock, it operates in PWM mode. The device can synchronize to an external clock over frequencies from 500 kHz to 750 kHz. Use the following waveform and duty-cycle guidelines when applying an external clock to the SYNC/MODE pin. The duty cycle can be between 30% and 70%. Clock under/overshoot should be less than 100 mV below GND or above VDD. When applying noisy clock signals, especially sharp edged signals from a long cable during evaluation, terminate the cable at its characteristic impedance; add an RC filter to the SYNC/MODE pin, if necessary, to soften the slew rate and 12 parator. In PWM mode, cycle-by-cycle current limiting is normally used. If an excessive load pulls the output voltage down to approximately 0.45V, then the device switches to a timed current limit mode. In timed current limit mode the internal PFET switch is turned off after the current comparator trips and the beginning of the next cycle is inhibited for 2.5 µs to force the instantaneous inductor current to ramp down to a safe value. Timed current limit prevents the loss of current control seen in some products when the output voltage is pulled low in serious overload conditions. (Continued) over/undershoot. Note that sharp edged signals from a pulse or function generator can develop under/overshoot as high as 10V at the end of an improperly terminated cable. Over-voltage Protection The LM3661 has an over-voltage comparator that prevents the output voltage from rising too high when the device is left in PWM mode under low-load conditions. Otherwise, the output voltage could rise out of regulation from the minimum energy transferred per cycle due to about 250 ns minimum on-time of the PFET switch while in PWM mode. When the output voltage rises by 70 mV over its regulation threshold, the OVP comparator inhibits PWM operation to skip pulses until the output voltage returns to the regulation threshold. In over voltage protection, output voltage and ripple increase slightly. Application Information PIN SELECTABLE OUTPUT The LM3661 features pin-selectable output voltage to eliminate the need for external feedback resistors. Select an output voltage of 1.05V or 1.25V/1.35V/1.4V by setting the VSEL pin low or high. VSEL may be set high by connecting to VDD or low by connecting to GND. Alternatively, VSEL may be driven off digitally by a logic gates that provide over 1.2V for high state and less than 0.4V for a low state to ensure valid logic levels. VSEL input has no internal pull down that pulls the input low, this pin must be set to a known state. Shutdown Mode Setting the EN input low, to SGND, places the LM3661 in a 0.5 µA (typ) shutdown mode. During shutdown, the PFET switch, NFET synchronous rectifier, reference, control and bias of the LM3661 are turned off. Setting EN high to VDD enables normal operation. While turning on, soft start is activated. EN is a Schmidt trigger digital input with thresholds that are independent of the input voltage at VDD. EN must be set low to turn off the LM3661 during under voltage conditions when the supply is less than the 2.7V minimum operating voltage. The LM3661 is designed for mobile phones and similar applications where power sequencing is determined by the system controller and internal UVLO (Under Voltage Lock Out) circuitry is unnecessary. The LM3661 has no UVLO circuitry. Although the LM3661 exhibits good behavior while enabled at low input voltages, this is not guaranteed. Isel Pin Connecting the ISEL pin high ( > 1.2V or Vin ) sets the internal current limit comparator to low value and low ( < 0.4 or GND) to high value. Note that ISEL pin has no internal pull down and this pin must connect to a known state of normal operation. Table 1 shows selected IOUT capability information. Table 1. ISEL condition and IOUT capability (Applies to both VSEL = H and VSEL = L) Start-up The LM3661 is designed to be started in LDO mode. Under these conditions, the output voltage will increase at a rate determined by the LDO current limit and the output capacitor and load. This ramp time is typically about 600 µs. The LM3661 may be started in PWM mode as well. Under these conditions, the reference voltage for the error amplifier is ramped up time is about 300µs and the output voltage will follow. In this way, the input inrush current and output voltage over shoot can be minimized. VOUT option ISEL IOUT capability 1.05V/1.25V H 300mA 1.05V/1.25V L TBDmA 1.05V/1.35V H 350mA 1.05V/1.35V L 450mA 1.05V/1.40V H 350mA 1.05V/1.40V L 450mA Mode Transition The LM3661 is designed to operate in two modes, LDO(Low Dropout Regulator) mode for light load (15mA Max.) and PWM Mode (Pulse Width Modulation) . As described in the Device Operation Section, setting the SYNC/MODE pin low yields LDO mode or high yields PWM mode. When mode transitions from LDO to PWM and vice versa, harsh transient conditions such as ramping the output load should be avoided. To maintain a smooth transition, it is recommended to keep the load to a minimum of 3mA or less for about 40us before ramping into heavy load to avoid a large dip at the output. Similarly, the same care must be applied when changing output voltage from 1.05V to 1.25V/1.35V/1.40V and vice versa (setting Vsel pin high or low) during full load. Figure 3 below shows the mode transition from LDO to PWM and PWM to LDO, and the load transient transition from light load to heavy load is delayed by 40µs to allow the PWM loop to respond properly. Thermal Shutdown Protection The LM3661 has thermal shutdown protection in PWM mode to protect from short-term misuse and overload conditions. When the junction temperature exceeds 150˚C, the device shuts down and re-starts in soft start after the temperature drops below 130˚C. Prolonged operation in thermal overload conditions may damage the device and is considered bad practice. Current Limiting Protection A current limit feature allows the LM3661 to protect itself and external components during overload conditions. Current limiting is implemented using an independent internal com- 13 www.national.com LM3661 Frequency Synchronization LM3661 Application Information (Continued) 20098833 FIGURE 3. INDUCTOR SELECTION There are a few things that one must consider when selecting an inductor for an application. They are the inductor DC current rating, inductor ripple current, DC-resistance of the inductor and value of the inductor. The DC current rating of the inductor denotes the maximum current before the inductor core enters saturation. Before selecting the DC current rating of the inductor, an inductor ripple current must be determined using Equation (1). The DC current of the inductor should be the maximum output current of the circuit plus half of the peak to peak current ripple of the inductor using Equation (2). (3) Where f is the operating frequency, ∆IL is the inductor current ripple and Vo is the desired output. Finally, the DC resistance (DCR) of the inductor also affect the overall efficiency of the solution. Lower DCR is recommended for better efficiency in handheld and battery operated applications. Consult inductor manufacture for this specification. Table 2 lists suggested inductors and suppliers. Table2. Suggested Inductor and Suppliers (1) Vendor D01608C-103 Coilcraft Web www.coilcraft.com P1174.103T Pulse www.pulseeng.com Panasonic www.panasonic.com P0770.103T (2) A good estimate for the inductor ripple current would be using a operation condition or assume the inductor ripple current to be about 30% of the maximum output current of the device. Consider the following example for LM3661 (when ISEL = L); a 10 µH, 450 mA load current with 1.4V output operates at 4.5V input and 600kHz in an application, solving for ∆IL using Equation (2) yields ∆IL = 160 mA. Therefore the maximum peak current (Equation (1)) in the application will be 530 mA (IO + 1/2∆IL). Thus, an inductor with DC current rating of 600 mA or higher should suffice for the application when ISEL = L. For a more conservative approach, it is best to select an inductor with a current rating of the maximum switch peak current of the device. Note that If smaller inductor is used in the application, the larger the inductor ripple current (Equation (1)). Care must be taken to select the inductor such that the peak current rating of the inductor accounts for minimum inductance and maximum current for the operating condition. Equation (3) can be used to calculate the inductor value if the application conditions are known: www.national.com Part Number Ell6GM100M INPUT AND OUTPUT CAPACITOR The LM3661 is designed for ceramic capacitor for its input and output filters. Ceramic capacitors such as X5R and X7R are recommended to use for input and output filters. These provide an optimal balance between small size, cost, reliability and performance. Do not use Y5V ceramic capacitors as they have poor dielectrics performance over temperature and voltage characteristics for a given value. Table 2 lists suggested capacitors and suppliers. A 10 µF input and 22 µF output ceramic capacitors are suggested in figure 2 (Typical application circuit) for optimal performance. The input filter capacitor supplies current to the PFET switch of the LM3661 in the first part of each cycle and reduces voltage ripple imposed on the input power source. The output filter capacitor smooths out current flow from the inductor and reduce output voltage ripple. These capacitors must be selected with sufficient capacitance and sufficiently low ESR 14 BOARD LAYOUT CONSIDERATION (Continued) PC board layout is an important part of DC-DC converter design. Poor board layout can disrupt the performance of a DC-DC converter and surrounding circuitry by contributing EMI, ground bounce, and resistive voltage loss in the traces. Below are layout recommendation to maximize device performance: 1) Place the inductor and filter capacitors close together and minimize the traces between components as they carry relatively high switching current and act as antennas. 2) Use wide traces between the power components and for power connections to DC-DC converters circuit. 3) Route noise sensitive traces such as the voltage feedback path away from noisy power components. 4) Connect the ground pins and filter capacitors together via a ground plane to prevent switching current circulating through the ground plane. Additional information regarding Micro SMD package layout can be found in Application note AN-1112. to perform these functions. The ESR, or equivalent series resistance, of the filter capacitors is a major factor in voltage ripple. Table 3 lists suggested capacitors suppliers. Table 3. Suggested capacitors and Suppliers Model Size (EIA) Vendor Input Filter Capacitor (10µF, 6.3V, X5R or X7R9 C2012X5R0J106M 2012 (0805) TDK JMK212BJ106MG 2012 (0805) Taiyo-Yuden GRM21BR60J106K 2012 (0805) muRata Output Filter Capacitor (22µF, 6.3V, X5R or X7R9 C3225X5R0J226M 3225(1210) TDK JMK325BJ226MG 3225(1210) Taiyo-Yuden GRM32DR60J226K 3225(1210) muRata 15 www.national.com LM3661 Application Information LM3661 Physical Dimensions inches (millimeters) unless otherwise noted NOTES: UNLESS OTHERWISE SPECIFIED 1. EPOXY COATING 2. 63Sn/37Pb EUTECTIC BUMP 3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD. 4. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION. REMAINING PINS ARE NUMBERED COUNTER CLOCKWISE. 5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS PACKAGE HEIGHT. 10-Bump micro SMD Package NS Package Number TLP10QTA The dimensions for X1, X2 and X3 are as given: X1 = 1.869 ± 0.030 mm X2 = 2.428 ± 0.030 mm X3 = 0.600 ± 0.075 mm www.national.com 16 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560 LM3661 450mA Subminiature, Micropower Step-Down DC-DC Converter for Ultra Low-Voltage Circuits Notes