Back G3DZ Power MOS FET Relay SSR Identical to the G6D in Size with a Maximum AC/DC Switching Current of 0.6 A Switching 0.6 A at 240 VAC or 100 VDC. 10-µA current leakage max. between open output terminals. 2,500-VAC dielectric strength ensured between input and output terminals. Input resistor and varistor incorporated. Switching full- and half-wave rectified alternating currents. Ordering Information Model Number Legend: G3DZ 1 2 3 4 3. Terminal P: PCB terminal 4. Zero Cross Function L: Without zero cross function 1. Load Voltage 2: A load voltage of 240 VAC 2. Load Current R6: A load current of 0.6 A Contact form SPST-NO Insulation Photodiode array Zero cross function No Accessories (Order Separately) See “Dimensions” for details. Connecting socket 38 P6D-04P Indicator No Applicable output load Rated input voltage 0.6 A at 5 VDC 3 to 264 VAC 12 VDC 3 to 125 VDC 24 VDC Model G3DZ-2R6PL G3DZ G3DZ Specifications Ratings Input Rated voltage Operating voltage Input impedance Voltage level Must operate 5 VDC 4 to 6 VDC 830 Ω±20% 4 VDC max. 12 VDC 9.6 to 14.4 VDC 2 kΩ±20% 9.6 VDC max. 24 VDC 19.2 to 28.8 VDC 4 kΩ±20% 19.2 VDC max. Must release 1 VDC min. Output Load voltage 3 to 264 VAC, 3 to 125 VDC Load current 100 µA to 0.6 A Inrush current 6 A (10 ms) Characteristics Operate time 6 ms max. Release time 10 ms max. Output ON-resistance 2.4 Ω max. Leakage current 10 µA max. (at 125 VDC) Insulation resistance 100 MΩ min. (at 500 VDC) Dielectric strength 2,500 VAC, 50/60 Hz for 1 min between input and output Vibration resistance Malfunction: 10 to 55 Hz, 1.5-mm double amplitude Shock resistance Malfunction: 1,000 m/s2 (approx. 100G) Ambient temperature Operating: –30°C to 85°C (with no icing) Storage: –30°C to 100°C (with no icing) Ambient humidity Operating: 45% to 85% Weight Approx. 3.1 g 39 G3DZ G3DZ Engineering Data Load Current vs. Ambient Temperature Characteristics Inrush Current Resistivity Non-repetitive (Keep the inrush current to half the rated value if it occurs repetitively.) G3DZ-2R6PL Load current (A) Inrush current (A. Peak) G3DZ-2R6PL Ambient temperature (°C) Energizing time (ms) Dimensions Note: 1. All units are in millimeters unless otherwise indicated. 2. Orientation marks are indicated as follows: G3DZ-2R6PL 17.5 0.5 Mounting Holes (Bottom View) 6.5 Terminal Arrangement/ Internal Connections (Bottom View) Tolerance: ±0.1 12.5 max. (0.71) (1.13) 2.54 Four, 1.1 dia. 3.5 0.8 0.5 7.62 2.54 5.08 Load – 5.08 0.3 1 2.54 Input voltage 5.08 15.24 – 5 Load 7 Input + 13 + P6D-04P Connecting Socket Mounting Holes (Bottom View) 19.7 max. Socket Mounting Height Tolerance: ±0.1 6.9 max. (0.86) (2.18) 2.54 Four, 1.1 dia. 18.5 mm max. 10.8 6±0.1 3.6 0.65 2.54 0.3 7.62 5.08 40 5.08 2.54 15.24 Load power supply G3DZ G3DZ Precautions If any reversed surge voltage is imposed on the input terminals, insert a diode in parallel to the input terminals as shown in the following circuit diagram and do not impose a reversed voltage value of 3 V or more. – 1 Input + 13 5 DC Load If a coil load such as a solenoid or electromagnetic valve is connected to the G3DZ, connect a diode in parallel to the load to absorb counter-electromotive force. 7 Load Load MOS FET Relay Input Load Connection When connecting a load generating a high inrush current (such as a lamp load) to the MOS FET Relay, make sure that the MOS FET Relay can withstand the inrush current. OMRON’s datasheets show the non-repetitive peak value of the MOS FET Relay’s inrush current durability. Normally allow 1/2 of this inrush current to flow through the MOS FET Relay. If an inrush current exceeding that value is expected, connect a quick-blowing fuse to protect the MOS FET Relays. AC Load No zero cross function is incorporated. The maximum operating frequency is 10 Hz. Forwarding/Reversing Control of Single-phase Inductive Motor Use a MOS FET Relay with an output voltage twice as large as the supply voltage. Contact your OMRON representative before using MOS FET Relays with 200 V output. SW1 Input SW2 – Input To shorten the time, connect a Zener diode and a regular diode in series as shown in the illustration above. The G3DZ switches full-wave rectified alternating currents, halfwave rectified alternating currents, and low capacity load currents. AC/DC Load + MOS FET Relay Or Load MOS FET Relay Input – MOS FET Relay + Input Load MOS FET Relay Motor + – For high-speed operation: AC Load + Or – DC – DC + DC Load Load power supply Operate SW1 for at least 30 ms after SW2 has been operated, or vice versa. Capacitive Load 1. Use a MOS FET Relay with an output voltage twice as large as the supply voltage because the supply voltage and charge voltage of the capacitor are imposed on the MOS FET Relay at the same time when the MOS FET Relay is turned OFF. 2. Limit the charge voltage of the capacitor to 1/2 of the peak inrush current value that is allowed to flow into the MOS FET Relay. + + MOS FET Relay Input – Load Load Load power supply – If an inductive AC load is connected to the G3DZ, connect a varistor as a surge absorber in parallel to the load. + Input – MOS FET Relay Load Load Although the G3DZ has a built-in varistor connected to the load terminals of the G3DZ to absorb noise, do not wire power lines or hightension lines along with the lines connected to the G3DZ in a single duct or the G3DZ may be damaged or malfunction due to induction. The surge absorption element must satisfy the following requirements. Operating voltage 100 to 120 VAC Operating voltage 200 to 240 VAC Varistor voltage 240 to 270 V Varistor voltage 440 to 470 V Inrush resistance 1,000 A min. Inrush resistance 1,000 A min. Handling Instructions Handle the G3DZ with care so that the G3DZ will not be damaged due to static electricty. 41