REVISIONS LTR DESCRIPTION A DATE (YR-MO-DA) APPROVED 00-10-24 Raymond Monnin Add case outline X. Remove figure 3, block diagram. REV SHEET REV SHEET REV STATUS REV A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Gary Zahn STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A DEFENSE SUPPLY CENTER COLUMBUS POST OFFICE BOX 3990 COLUMBUS, OHIO 43216-5000 CHECKED BY Michael C. Jones APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, +5 AND r12 VOLT, TRIPLE CHANNEL, DC-DC CONVERTER DRAWING APPROVAL DATE 93-06-23 REVISION LEVEL A SIZE A CAGE CODE 5962-93158 67268 SHEET DSCC FORM 2233 APR 97 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 1 OF 12 5962-E035-01 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes, class D (lowest reliability), class E, (exceptions), class G (lowered high reliability), class H (high reliability), and class K, (highest reliability) and a choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - ~ ~ ~ 93158 ~ ~ ~ Federal stock class designator \ 01 H X Device type (see 1.2.2) Device class designator (see 1.2.3) Case outline (see 1.2.4) ~ ~ ~ RHA designator (see 1.2.1) / ~ ~ ~ ~ ~ ~ X ~ ~ ~ Lead finish (see 1.2.5) \/ Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type 01 Generic number Circuit function DC-DC converter, 30 W, +5 V and r12 V triple output ATR2812T/CH, ATR2812TF/CH 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level as follows: Device class Device performance documentation D, E, G, H, or K Certification and qualification to MIL-PRF-38534 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator X Z Terminals See figure 1 See figure 1 10 10 Package style Dual-in line Flange mount 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage range .................................................................... Power dissipation ...................................................................... Lead temperature (soldering, 10 seconds) ................................ Storage temperature ................................................................. 1/ -0.5 V dc to +50 V dc 14 W +300 qC -65qC to +150qC Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93158 A REVISION LEVEL A SHEET 2 1.4 Recommended operating conditions. Input voltage range...................................................................... Output currents: +5 V output 1/ 2/ .................................................................... +12 V output 1/ 2/ .................................................................. Output power 1/ 3/ ..................................................................... Case operating temperature range (TC) ..................................... +16 V dc to +40 V dc +100 mA to +4000 mA r625 mA d 30 W -55qC to +125qC 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 - List of Standard Microcircuit Drawings (SMD's). MIL-HDBK-780 - Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. Therefore, the tests and inspections herein may not be performed for the applicable device class (see MIL-PRF-38534). Furthermore, the manufacturer may take exceptions or use alternate methods to the tests and inspections herein and not perform them. However, the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. 1/ 2/ 3/ Although operation with no load is permissible, light loading on the main (+5 volt) output may cause the output voltage of the auxiliary outputs (r12 volt) to drop out of regulation. It is therefore recommended that at least 100 mA or 20 percent of the total output power, whichever is greater, be taken from the main (+5 volt) output. Total combined output power not to exceed 30 watts. Derate output power linearly above case temperature +125qC to 0 at +135qC. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93158 A REVISION LEVEL A SHEET 3 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked in MIL-HDBK-103 and QML-38534. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. b. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. (2) TC as specified in accordance with table I of method 1015 of MIL-STD-883. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93158 A REVISION LEVEL A SHEET 4 TABLE I. Electrical performance characteristics. Test Output voltage 1/ Symbol VOUT Conditions 1/ -55qC d TC d +125qC VIN = 28 V, r5%, CL = 0 unless otherwise specified Group A subgroups Limits Device type Min IOUT = 0 (main) 01 1 Output current 1/ 2/ 3/ 4/ Output ripple voltage 1/ 5/ Line regulation 1/ 3/ Load regulation 1/ 3/ IOUT VRIP VRLINE VRLOAD 5.05 4.90 5.10 1 r11.88 r12.12 2,3 r11.76 r12.24 VIN = 16, 28, and 40 V dc (main) 1,2,3 VIN = 16, 28, and 40 V dc (dual) 1,2,3 VIN = 16, 28, and 40 V dc, B.W. = 20 Hz to 2 MHz (main) 1,2,3 VIN = 16, 28, and 40 V dc, B.W. = 20 Hz to 2 MHz (dual) 1,2,3 VIN = 16, 28, and 40 V dc, IOUT = 100, 2000, and 4000 mA (main) 1,2,3 VIN = 16, 28, and 40 V dc, IOUT = 0, r208, and r417 mA (dual) 1 r30 2,3 r60 1,2,3 VIN = 16, 28, and 40 V dc, IOUT = 100, 2000, and 4000 mA (main) 01 100.0 4000 0.0 r625 01 IIN V mA 60 mVp-p 40 01 25 01 mV 50 mV r60 VIN = 16, 28, and 40 V dc, IOUT = 0, r208, and r417 mA (dual) Input current Max 4.95 2,3 IOUT = 0 (dual) Unit IOUT = 0, inhibit (pin 8) tied to input return (pin 10) 1,2,3 IOUT = 0, inhibit (pin 8) = open 01 15 1,3 50 2 75 mA See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93158 A REVISION LEVEL A SHEET 5 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55qC d TC d +125qC VIN = 28 V, r5%, CL = 0 unless otherwise specified Group A subgroups Limits Device type Min Input ripple current 5/ IRIP IOUT = 4000 mA (main), IOUT = r417 mA (dual), B.W. = 20 Hz to 2 MHz 1,2,3 01 Efficiency EFF IOUT = 4000 mA (main), IOUT = r417 mA (dual) 1 01 ISO Input to output or any pin to case (except pin 7) at 500 V dc, TC = +25qC Power dissipation load fault 3/ PD Overload 6/ Max 50 mAp-p % 75 2,3 Isolation Unit 72 1 01 1,2,3 01 M: 100 14 Short circuit W 9 Switching frequency FS IOUT = 4000 mA (main), IOUT = r417 mA (dual) 4,5,6 01 500 600 kHz Sync frequency range FSYNC IOUT = 4000 mA (main), IOUT = r417 mA (dual) 1,2,3 01 500 700 kHz Inhibit open circuit voltage VOI 1,2,3 01 9 13 V Output response to step transient load changes 7/ VOTLOAD 4 01 -300 +300 5,6 -500 +500 4,5,6 -1000 +1000 50 percent load to /from 100 percent load No load to /from 50 percent load Recovery time to step transient load changes 7/ 8/ TTLOAD 50 percent load to /from 100 percent load 01 4 mV pk Ps 100 5,6 200 No load to 50 percent load 4,5,6 5 50 percent load to no load 4,5,6 10 ms See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93158 A REVISION LEVEL A SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55qC d TC d +125qC VIN = 28 V, r5%, CL = 0 unless otherwise specified Group A subgroups Limits Device type Min Unit Max Output response to transient step line changes 9/ 10/ VOTLINE Input step 16 from/to 40 V dc, IOUT = 4000 mA (main), IOUT = r417 mA (dual) 4,5,6 01 r1500 Recovery time transient step line changes 8/ 9/ 10/ TTLINE Input step 16 from/to 40 V dc, IOUT = 4000 mA (main), IOUT = r417 mA (dual) 4,5,6 01 10 Turn on overshoot 1/ VTONOS IOUT = 0 and 4000 mA (main), IOUT = 0 and r417 mA (dual) 4,5,6 01 1000 Turn on delay 1/ 11/ TOND IOUT = 0 and 4000 mA (main), IOUT = 0 and r417 mA (dual) 4,5,6 01 25 ms Load fault recovery 10/ TRLF 4,5,6 01 25 ms 1/ 2/ 3/ 4/ 5/ 6/ 7/ 8/ 9/ 10/ 11/ mV pk ms mV pk Tested at each output. Parameter guaranteed by line and load regulation tests. Although operation with no load is permissible, light loading on the main (+5 volt) output may cause the output voltage of the auxiliary outputs (r12 volt) to drop out of regulation. It is therefore recommended that at least 100 mA or 20 percent of the output power, whichever is greater, be taken from the main (+5 volt) output. Total combined output power d30 watts. Bandwidth guaranteed by design. Tested for 20 kHz to 2 MHz. An overload is that condition with a load in excess of the rated load but less than that necessary to trigger the overload protection circuit and is the condition of maximum power dissipation. Load step transition time between 2 and 10 microseconds. Recovery time is measured from the initiation of the transient to where VOUT has returned to within r1 percent of VOUT at 50 percent load. Input step transition time between 2 and 10 microseconds. Parameter shall be tested as part of design characterization and after design or process changes. Thereafter parameters shall be guaranteed to the limits specified in table 1. Turn on delay time measurement is for either a step application of power at the input or the removal of a ground signal from the inhibit pin (pin 8) while power is applied to the input. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93158 A REVISION LEVEL A SHEET 7 Case outline X. Millimeters Symbol Min A 0.89 D 1.14 10.03 10.29 0.035 25.53 0.045 1.950 0.395 34.29 25.27 Max 0.405 49.53 E eA Min 10.29 øb e Max Inches 0.405 1.350 0.995 1.005 L 6.35 6.86 0.250 0.270 NOTES: 1. The U.S. government perferred system of measurement is the metric SI. This case outline was designed using inchpound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Case outline X weight: 72 grams maximum. FIGURE 1. Case outline(s). STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93158 A REVISION LEVEL A SHEET 8 Case outline Z. Symbol Millimeters Min A øb D D1 e E eA F L øP q 0.89 10.03 25.27 6.35 3.99 59.82 Max 10.29 1.14 68.58 49.53 10.29 34.29 25.53 1.40 6.86 4.24 60.07 Inches Min 0.035 0.395 0.995 0.250 0.157 2.355 Max 0.405 0.045 2.700 1.950 0.405 1.350 1.005 0.055 0.270 0.167 2.365 NOTES: 1. The U.S. government perferred system of measurement is the metric SI. This case outline was designed using inchpound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Case outline X weight: 76 grams maximum. FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93158 A REVISION LEVEL A SHEET 9 Device type 01 Case outlines X and Z Terminal number Terminal symbol 1 Positive input 2 +5 V dc output 3 Output return 4 -12 V dc output 5 +12 V dc output 6 No connection 7 Case ground 8 Inhibit input 9 Synchronization input 10 Input return FIGURE 2. Terminal connections. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93158 A REVISION LEVEL A SHEET 10 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters Final electrical parameters 1*,2,3,4,5,6 Group A test requirements 1,2,3,4,5,6 Group C end-point electrical parameters 1,4 Not applicable End-point electrical parameters for radiation hardness assurance (RHA) devices * PDA applies to subgroup 1. 4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance with MIL-PRF-38534 and as specified herein. 4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 7, 8, 9, 10, and 11 shall be omitted. 4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534. 4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. (2) TC as specified in accordance with table I of method 1005 of MIL-STD-883. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534. 4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93158 A REVISION LEVEL A SHEET 11 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished in accordance with MIL-PRF-38534. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Post Office Box 3990, Columbus, Ohio 432165000, or telephone (614) 692-0512. 6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK103 and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DSCC-VA and have agreed to this drawing. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93158 A REVISION LEVEL A SHEET 12 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 00-10-24 Approved sources of supply for SMD 5962-93158 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. 1/ 2/ Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9315801HXA 52467 ATR2812T/CH 5962-9315801HZA 52467 ATR2812TF/CH The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the Vendor to determine its availability. Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Vendor CAGE number 52467 Vendor name and address Lambda Advanced Analog, Incorporated 2270 Martin Avenue Santa Clara, CA 95050-2781 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin.