2.0 Amp Output Current IGBT Gate Drive Optocoupler Technical Data HCPL-3120 HCPL-J312 HCNW3120 Features • 2.0 A Minimum Peak Output Current • 15 kV/µs Minimum Common Mode Rejection (CMR) at VCM = 1500 V • 0.5 V Maximum Low Level Output Voltage (VOL) Eliminates Need for Negative Gate Drive • ICC = 5 mA Maximum Supply Current • Under Voltage Lock-Out Protection (UVLO) with Hysteresis • Wide Operating VCC Range: 15 to 30 Volts • 500 ns Maximum Switching Speeds • Industrial Temperature Range: -40°C to 100°C • Safety Approval UL Recognized 2500 Vrms for 1 min. for HCPL-3120 3750 Vrms for 1 min. for HCPL-J312 5000 Vrms for 1 min. for HCNW3120 Applications CSA Approval VDE 0884 Approved VIORM = 630 Vpeak for HCPL-3120 (Option 060) VIORM = 891 Vpeak for HCPL-J312 VIORM = 1414 Vpeak for HCNW3120 BSI Certified (HCNW3120 only) (Pending) • IGBT/MOSFET Gate Drive • AC/Brushless DC Motor Drives • Industrial Inverters • Switch Mode Power Supplies Functional Diagram HCPL-3120/J312 N/C HCNW3120 8 VCC 1 N/C ANODE 2 7 VO ANODE 2 CATHODE 3 6 VO CATHODE 3 N/C 4 SHIELD 5 VEE 8 VCC 1 N/C 4 7 VO 6 N/C SHIELD 5 VEE TRUTH TABLE LED VCC - VEE VCC - VEE “POSITIVE GOING” “NEGATIVE GOING” (i.e., TURN-ON) (i.e., TURN-OFF) VO OFF 0 - 30 V 0 - 30 V LOW ON 0 - 11 V 0 - 9.5 V LOW ON 11 - 13.5 V 9.5 - 12 V TRANSITION ON 13.5 - 30 V 12 - 30 V HIGH A 0.1 µF bypass capacitor must be connected between pins 5 and 8. CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. 2 Description The HCPL-3120 contains a GaAsP LED while the HCPL-J312 and the HCNW3120 contain an AlGaAs LED. The LED is optically coupled to an integrated circuit with a power output stage. These optocouplers are ideally suited for driving power IGBTs and MOSFETs used in motor control inverter applications. The high operating voltage range of the output stage provides the drive voltages required by gate controlled devices. The voltage and current supplied by these optocouplers make them ideally suited for directly driving IGBTs with ratings up to 1200 V/100 A. For IGBTs with higher ratings, the HCPL-3120 series can be used to drive a discrete power stage which drives the IGBT gate. The HCNW3120 has the highest insulation voltage of VIORM = 1414 Vpeak in the VDE0884. The HCPL-J312 has an insulation voltage of VIORM = 891 Vpeak and the VIORM = 630 Vpeak is also available with the HCPL-3120 (Option 060). Selection Guide Part Number Output Peak Current ( IO) VDE0884 Approval HCPL-3120 HCPL-J312 2.0 A 2.0 A VIORM = 630 Vpeak VIORM = 891 Vpeak (Option 060) HCNW3120 2.0 A VIORM = 1414 Vpeak HCPL-3150* 0.5 A VIORM = 630 Vpeak (Option 060) *The HCPL-3150 Data sheet available. Contact Agilent sales representative or authorized distributor. Ordering Information Specify Part Number followed by Option Number (if desired) Example: HCPL-3120#XXX 060 = VDE0884, VIORM = 630 Vpeak (HCPL-3120 only) 300 = Gull Wing Surface Mount Option 500 = Tape and Reel Packaging Option Option 500 contains 1000 units (HCPL-3120/J312), 750 units (HCNW3120) per reel. Other options contain 50 units (HCPL-3120/J312), 42 units (HCNW312) per tube. Option data sheets available. Contact Agilent sales representative or authorized distributor. 3 Package Outline Drawings HCPL-3120 Outline Drawing (Standard DIP Package) 7.62 ± 0.25 (0.300 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) 8 TYPE NUMBER 7 6 5 6.35 ± 0.25 (0.250 ± 0.010) OPTION CODE* DATE CODE A XXXXZ YYWW 1 2 3 4 1.78 (0.070) MAX. 1.19 (0.047) MAX. 5° TYP. 4.70 (0.185) MAX. + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 0.51 (0.020) MIN. 2.92 (0.115) MIN. DIMENSIONS IN MILLIMETERS AND (INCHES). * MARKING CODE LETTER FOR OPTION NUMBERS. "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. 0.65 (0.025) MAX. 1.080 ± 0.320 (0.043 ± 0.013) 2.54 ± 0.25 (0.100 ± 0.010) HCPL-3120 Gull Wing Surface Mount Option 300 Outline Drawing PAD LOCATION (FOR REFERENCE ONLY) 9.65 ± 0.25 (0.380 ± 0.010) 8 7 6 1.016 (0.040) 1.194 (0.047) 5 4.826 TYP. (0.190) 6.350 ± 0.25 (0.250 ± 0.010) 1 2 3 9.398 (0.370) 9.906 (0.390) 4 1.194 (0.047) 1.778 (0.070) 1.19 (0.047) MAX. 1.780 (0.070) MAX. 9.65 ± 0.25 (0.380 ± 0.010) 7.62 ± 0.25 (0.300 ± 0.010) 4.19 MAX. (0.165) 1.080 ± 0.320 (0.043 ± 0.013) 0.635 ± 0.130 2.54 (0.025 ± 0.005) (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). 0.381 (0.015) 0.635 (0.025) 0.635 ± 0.25 (0.025 ± 0.010) + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 12° NOM. 4 Package Outline Drawings HCPL-J312 Outline Drawing (Standard DIP Package) 7.62 ± 0.25 (0.300 ± 0.010) 9.80 ± 0.25 (0.386 ± 0.010) 8 TYPE NUMBER 7 6 5 6.35 ± 0.25 (0.250 ± 0.010) OPTION CODE* DATE CODE A XXXXZ YYWW 1 2 3 4 1.78 (0.070) MAX. 1.19 (0.047) MAX. 5° TYP. 4.70 (0.185) MAX. + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 0.51 (0.020) MIN. 2.92 (0.115) MIN. 0.65 (0.025) MAX. 1.080 ± 0.320 (0.043 ± 0.013) 2.54 ± 0.25 (0.100 ± 0.010) DIMENSIONS IN MILLIMETERS AND (INCHES). * MARKING CODE LETTER FOR OPTION NUMBERS. "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. HCPL-J312 Gull Wing Surface Mount Option 300 Outline Drawing PAD LOCATION (FOR REFERENCE ONLY) 9.80 ± 0.25 (0.386 ± 0.010) 8 7 6 1.016 (0.040) 1.194 (0.047) 5 4.826 TYP. (0.190) 6.350 ± 0.25 (0.250 ± 0.010) 1 2 3 9.398 (0.370) 9.906 (0.390) 4 1.194 (0.047) 1.778 (0.070) 1.19 (0.047) MAX. 1.780 (0.070) MAX. 9.65 ± 0.25 (0.380 ± 0.010) 7.62 ± 0.25 (0.300 ± 0.010) 4.19 MAX. (0.165) 1.080 ± 0.320 (0.043 ± 0.013) 0.635 ± 0.130 2.54 (0.025 ± 0.005) (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). 0.381 (0.015) 0.635 (0.025) 0.635 ± 0.25 (0.025 ± 0.010) + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 12° NOM. 5 HCNW3120 Outline Drawing (8-Pin Wide Body Package) 11.00 MAX. (0.433) 11.15 ± 0.15 (0.442 ± 0.006) 8 7 6 9.00 ± 0.15 (0.354 ± 0.006) 5 TYPE NUMBER A HCNWXXXX DATE CODE YYWW 1 2 3 4 10.16 (0.400) TYP. 1.55 (0.061) MAX. 7° TYP. + 0.076 0.254 - 0.0051 + 0.003) (0.010 - 0.002) 5.10 MAX. (0.201) 3.10 (0.122) 3.90 (0.154) 0.51 (0.021) MIN. 2.54 (0.100) TYP. 1.78 ± 0.15 (0.070 ± 0.006) 0.40 (0.016) 0.56 (0.022) DIMENSIONS IN MILLIMETERS (INCHES). HCNW3120 Gull Wing Surface Mount Option 300 Outline Drawing 11.15 ± 0.15 (0.442 ± 0.006) 8 7 6 PAD LOCATION (FOR REFERENCE ONLY) 5 6.15 (0.242)TYP. 9.00 ± 0.15 (0.354 ± 0.006) 12.30 ± 0.30 (0.484 ± 0.012) 1 2 3 4 1.3 (0.051) 0.9 (0.035) 12.30 ± 0.30 (0.484 ± 0.012) 1.55 (0.061) MAX. 11.00 MAX. (0.433) 4.00 MAX. (0.158) 1.78 ± 0.15 (0.070 ± 0.006) 2.54 (0.100) BSC 0.75 ± 0.25 (0.030 ± 0.010) 1.00 ± 0.15 (0.039 ± 0.006) + 0.076 0.254 - 0.0051 + 0.003) (0.010 - 0.002) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). 7° NOM. 6 TEMPERATURE – °C Reflow Temperature Profile 260 240 220 200 180 160 ∆T = 145°C, 1°C/SEC ∆T = 115°C, 0.3°C/SEC 140 120 100 80 60 40 20 0 ∆T = 100°C, 1.5°C/SEC 0 1 2 3 4 5 6 7 8 9 10 11 12 TIME – MINUTES MAXIMUM SOLDER REFLOW THERMAL PROFILE (NOTE: USE OF NON-CHLORINE ACTIVATED FLUXES IS RECOMMENDED.) Regulatory Information Agency/Standard Underwriters Laboratory (UL) HCPL-3120 HCPL-J312 HCNW3120 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ Recognized under UL 1577, Component Recognition Program, Category, File E55361 Canadian Standards Association (CSA) File CA88324, per Component Acceptance Notice #5 Verband Deutscher Electrotechniker (VDE) DIN VDE 0884 (June 1992) British Standards Institute (BSI) Certification According to BS EN60065: 1994 (BS415:1994), BS EN60950: 1992 (BS7002:1992) Option 060 Pending Insulation and Safety Related Specifications Parameter Minimum External Air Gap (Clearance) Minimum External Tracking (Creepage) Minimum Internal Plastic Gap (Internal Clearance) Tracking Resistance (Comparative Tracking Index) Isolation Group Value HCPL- HCPLSymbol 3120 J312 L(101) 7.1 7.4 L(102) CTI HCNW 3120 9.6 Units mm 7.4 8.0 10.0 mm 0.08 0.5 1.0 mm >175 >175 >200 Volts IIIa IIIa IIIa Conditions Measured from input terminals to output terminals, shortest distance through air. Measured from input terminals to output terminals, shortest distance path along body. Insulation thickness between emitter and detector; also known as distance through insulation. DIN IEC 112/VDE 0303 Part 1 Material Group (DIN VDE 0110, 1/89, Table 1) 7 All Agilent data sheets report the creepage and clearance inherent to the optocoupler component itself. These dimensions are needed as a starting point for the equipment designer when determining the circuit insulation requirements. However, once mounted on a printed circuit board, minimum creepage and clearance requirements must be met as specified for individual equipment standards. For creepage, the shortest distance path along the surface of a printed circuit board between the solder fillets of the input and output leads must be considered. There are recommended techniques such as grooves and ribs which may be used on a printed circuit board to achieve desired creepage and clearances. Creepage and clearance distances will also change depending on factors such as pollution degree and insulation level. VDE0884 Insulation Related Characteristics Description Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤ 150 V rms for rated mains voltage ≤ 300 V rms for rated mains voltage ≤ 450 V rms for rated mains voltage ≤ 600 V rms for rated mains voltage ≤ 1000 V rms Climatic Classification Pollution Degree (DIN VDE 0110/1.89) Maximum Working Insulation Voltage Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test, tm = 1 sec, Partial Discharge < 5pC Input to Output Test Voltage, Method a* VIORM x 1.5 = VPR, Type and Sample Test, tm = 60 sec, Partial Discharge < 5pC Highest Allowable Overvoltage* (Transient Overvoltage, tini = 10 sec) Safety Limiting Values – maximum values allowed in the event of a failure, also see Figure 37. Case Temperature Input Current Output Power Insulation Resistance at TS, VIO = 500 V Symbol HCPL-3120 Option 060 HCPL-J312 HCNW3120 Unit I-IV I-IV I-III I-IV I-IV I-III I-III VIORM VPR 55/100/21 2 630 1181 55/100/21 2 891 1670 I-IV I-IV I-IV I-IV I-III 55/100/21 2 1414 2652 Vpeak Vpeak VPR 945 1336 2121 Vpeak VIOTM 6000 6000 8000 Vpeak TS IS INPUT PS OUTPUT RS 175 230 600 ≥ 109 175 400 600 ≥ 109 150 400 700 ≥ 109 °C mA mW Ω *Refer to the VDE0884 section (page 1-6/8) of the Isolation Control Component Designer's Catalog for a detailed description of Method a/b partial discharge test profiles. Note: These optocouplers are suitable for “safe electrical isolation” only within the safety limit data. Maintenance of the safety data shall be ensured by means of protective circuits. Surface mount classification is Class A in accordance with CECC 00802. 8 Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Average Input Current Peak Transient Input Current (<1 µs pulse width, 300 pps) Reverse Input Voltage HCPL-3120 HCPL-J312 HCNW3120 “High” Peak Output Current “Low” Peak Output Current Supply Voltage Input Current (Rise/Fall Time) Output Voltage Output Power Dissipation Total Power Dissipation Lead Solder HCPL-3120 Temperature HCPL-J312 HCNW3120 Solder Reflow Temperature Profile Symbol TS TA IF(AVG) Max. 125 100 25 Units °C °C mA IF(TRAN) 1.0 A VR 5 3 Volts IOH(PEAK) IOL(PEAK) (VCC - VEE) tr(IN) / tf(IN) VO(PEAK) PO PT Min. -55 -40 260°C for 10 sec., up to seating plane See Package Outline Drawings section Symbol (VCC - VEE) IF(ON) VF(OFF) TA 1 2.5 A 2 2.5 A 2 0 35 Volts 500 ns 0 VCC Volts 250 mW 3 295 mW 4 260°C for 10 sec., 1.6 mm below seating plane Recommended Operating Conditions Parameter Power Supply Voltage Input Current (ON) HCPL-3120 HCPL-J312 HCNW3120 Input Voltage (OFF) Operating Temperature Note Min. 15 7 10 -3.0 -40 Max. 30 Units Volts 16 mA 0.8 100 V °C 9 Electrical Specifications (DC) Over recommended operating conditions (TA = -40 to 100°C, I F(ON) = 7 to 16 mA, VF(OFF) = -3.0 to 0.8 V, VCC = 15 to 30 V, VEE = Ground) unless otherwise specified. Parameter High Level Symbol I OH Device Output Current Low Level IOL Output Current High Level Output Voltage Low Level Output Voltage High Level Supply Current Low Level Supply Current Threshold Input Current Low to High Threshold Input Voltage High to Low Input Forward Voltage Temperature Coefficient of Forward Voltage Input Reverse Breakdown Voltage Input Capacitance UVLO Threshold VOH Min. Typ.* 0.5 1.5 2.0 0.5 2.0 2.0 (VCC - 4) (VCC - 3) Max. Units A A A A V VOL 0.1 0.5 V I CCH 2.5 5.0 mA I CCL 2.5 5.0 mA 2.3 1.0 2.3 5.0 mA I FLH HCPL-3120 HCPL-J312 HCNW3120 VFHL 0.8 VF 1.2 HCPL-3120 HCPL-J312 HCNW3120 ∆VF /∆TA HCPL-3120 HCPL-J312 HCNW3120 BVR CIN VUVLO+ VUVLO– UVLO Hysteresis UVLOHYS HCPL-3120 HCPL-J312 HCNW3120 HCPL-3120 HCPL-J312 HCNW3120 Test Conditions VO = (VCC - 4 V) VO = (VCC - 15 V) VO = (VEE + 2.5 V) VO = (VEE + 15 V) I O = -100 mA I O = 100 mA Fig. 2, 3, 17 5, 6, 18 1, 3, 19 4, 6, 20 7, 8 Output Open, I F = 7 to 16 mA Output Open, VF = -3.0 to +0.8 V I O = 0 mA, 9, 15, VO > 5 V 21 8.0 V 1.5 1.6 1.8 1.95 -1.6 -1.3 V IF = 10 mA 16 mV/°C I F = 10 mA 5 3 60 70 11.0 12.3 13.5 9.5 10.7 1.6 12.0 *All typical values at TA = 25°C and VCC - VEE = 30 V, unless otherwise noted. V I R = 10 µA I R = 100 µA pF f = 1 MHz, VF = 0 V V VO > 5 V, IF = 10 mA 22, 34 Note 5 2 5 2 6, 7 10 Switching Specifications (AC) Over recommended operating conditions (TA = -40 to 100°C, IF(ON) = 7 to 16 mA, VF(OFF) = -3.0 to 0.8 V, VCC = 15 to 30 V, VEE = Ground) unless otherwise specified. Parameter Symbol Min. Propagation Delay tPLH 0.10 Time to High Output Level Propagation Delay tPHL 0.10 Time to Low Output Level Pulse Width PWD Distortion Propagation Delay PDD -0.35 Difference Between (tPHL - tPLH) Any Two Parts Rise Time tr Fall Time tf UVLO Turn On tUVLO ON Delay UVLO Turn Off tUVLO OFF Delay Output High Level |CMH| 15 Common Mode Transient Immunity Output Low Level |CML| 15 Common Mode Transient Immunity Typ.* 0.30 Max. 0.50 Units µs 0.30 0.50 µs 0.3 µs 0.35 µs 35, 36 µs µs µs 23 0.1 0.1 0.8 0.6 Test Conditions Rg = 10 Ω, Cg = 10 nF, f = 10 kHz, Duty Cycle = 50% Fig. 10, 11, 12, 13, 14, 23 Note 16 17 VO > 5 V, IF = 10 mA 12 22 VO < 5 V, IF = 10 mA 30 kV/µs 30 kV/µs *All typical values at TA = 25°C and VCC - VEE = 30 V, unless otherwise noted. TA = 25°C, IF = 10 to 16 mA, VCM = 1500 V, VCC = 30 V TA = 25°C, VCM = 1500 V, VF = 0 V, VCC = 30 V 24 13, 14 13, 15 11 Package Characteristics Over recommended temperature (TA = -40 to 100°C) unless otherwise specified. Parameter Symbol Device Min. Typ. Max. Units Test Conditions Input-Output VISO HCPL-3120 2500 VRMS RH < 50%, Momentary HCPL-J312 3750 t = 1 min., Withstand Voltage** HCNW3120 5000 TA = 25°C Resistance RI-O HCPL-3120 1012 Ω VI-O = 500 VDC (Input-Output) HCPL-J312 HCNW3120 1012 1013 TA = 25°C 1011 TA = 100°C Capacitance CI-O HCPL-3120 0.6 pF f = 1 MHz (Input-Output) HCPL-J312 0.8 HCNW3120 0.5 0.6 LED-to-Case θLC 467 °C/W Thermocouple Thermal Resistance located at center LED-to-Detector θLD 442 °C/W underside of package Thermal Resistance Detector-to-Case θDC 126 °C/W Thermal Resistance Fig. Note 8, 11 9, 11 10, 11 11 28 *All typicals at TA = 25°C. **The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to your equipment level safety specification or Agilent Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage.” Notes: 1. Derate linearly above 70°C free-air temperature at a rate of 0.3 mA/°C. 2. Maximum pulse width = 10 µs, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with IO peak minimum = 2.0 A. See Applications section for additional details on limiting IOH peak. 3. Derate linearly above 70°C free-air temperature at a rate of 4.8 mW/°C. 4. Derate linearly above 70°C free-air temperature at a rate of 5.4 mW/°C. The maximum LED junction temperature should not exceed 125°C. 5. Maximum pulse width = 50 µs, maximum duty cycle = 0.5%. 6. In this test VOH is measured with a dc load current. When driving capacitive loads VOH will approach VCC as IOH approaches zero amps. 7. Maximum pulse width = 1 ms, maximum duty cycle = 20%. 8. In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 3000 Vrms for 1 second (leakage detection current limit, I I-O ≤ 5 µA). 9. In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 Vrms for 1 second (leakage detection current limit, I I-O ≤ 5 µA). 10. In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 Vrms for 1 second (leakage detection current limit, I I-O ≤ 5 µA). 11. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together. 12. The difference between tPHL and tPLH between any two HCPL-3120 parts under the same test condition. 13. Pins 1 and 4 need to be connected to LED common. 14. Common mode transient immunity in the high state is the maximum tolerable dVCM/dt of the common mode pulse, VCM, to assure that the output will remain in the high state (i.e., VO > 15.0 V). 15. Common mode transient immunity in a low state is the maximum tolerable dVCM/dt of the common mode pulse, VCM, to assure that the output will remain in a low state (i.e., VO < 1.0 V). 16. This load condition approximates the gate load of a 1200 V/75A IGBT. 17. Pulse Width Distortion (PWD) is defined as |tPHL-t PLH| for any given device. -1 2.0 IF = 7 to 16 mA IOUT = -100 mA VCC = 15 to 30 V VEE = 0 V -2 -3 -4 -40 -20 0 20 40 60 80 100 IF = 7 to 16 mA VOUT = (VCC - 4 V) VCC = 15 to 30 V VEE = 0 V 1.8 1.6 1.4 1.2 1.0 -40 -20 0 20 40 60 80 TA – TEMPERATURE – °C TA – TEMPERATURE – °C Figure 1. VOH vs. Temperature. Figure 2. IOH vs. Temperature. 0.20 0.15 0.10 0.05 -20 0 20 40 60 80 VF (OFF) = -3.0 TO 0.8 V VOUT = 2.5 V VCC = 15 TO 30 V VEE = 0 V 3 2 1 0 -40 100 TA – TEMPERATURE – °C 20 40 60 80 100 3.0 2.5 VCC = 30 V VEE = 0 V IF = 10 mA for ICCH IF = 0 mA for ICCL 1.5 -40 -20 0 20 40 60 80 TA – TEMPERATURE – °C Figure 7. ICC vs. Temperature. 100 -4 IF = 7 to 16 mA VCC = 15 to 30 V VEE = 0 V -5 -6 0 0.5 1.0 1.5 2.0 2.5 IOH – OUTPUT HIGH CURRENT – A 3.0 2.5 IF = 10 mA for ICCH IF = 0 mA for ICCL TA = 25 °C VEE = 0 V 2.0 15 20 25 VCC – SUPPLY VOLTAGE – V Figure 8. ICC vs. VCC. VF(OFF) = -3.0 to 0.8 V VCC = 15 to 30 V VEE = 0 V 3 2 1 0 100 °C 25 °C -40 °C 0 0.5 1.0 Figure 6. VOL vs. I OL. ICCH ICCL 1.5 -3 1.5 2.0 IOL – OUTPUT LOW CURRENT – A 3.5 ICCH ICCL ICC – SUPPLY CURRENT – mA ICC – SUPPLY CURRENT – mA 0 Figure 5. IOL vs. Temperature. 3.5 2.0 -20 TA – TEMPERATURE – °C Figure 4. VOL vs. Temperature. 100 °C 25 °C -40 °C -2 4 VOL – OUTPUT LOW VOLTAGE – V IOL – OUTPUT LOW CURRENT – A VOL – OUTPUT LOW VOLTAGE – V VF (OFF) = -3.0 TO 0.8 V IOUT = 100 mA VCC = 15 TO 30 V VEE = 0 V -1 Figure 3. VOH vs. IOH . 4 0.25 0 -40 100 (VOH – VCC ) – OUTPUT HIGH VOLTAGE DROP – V 0 IOH – OUTPUT HIGH CURRENT – A (VOH – VCC ) – HIGH OUTPUT VOLTAGE DROP – V 12 30 2.5 VCC = 15 TO 30 V VEE = 0 V OUTPUT = OPEN 4 3 2 1 0 -40 -20 0 20 40 60 80 100 TA – TEMPERATURE – °C HCPL-J312 5 VCC = 15 TO 30 V VEE = 0 V OUTPUT = OPEN 4 3 2 1 0 -40 -20 0 20 40 60 80 100 TA – TEMPERATURE – °C IFLH – LOW TO HIGH CURRENT THRESHOLD – mA HCPL-3120 5 IFLH – LOW TO HIGH CURRENT THRESHOLD – mA IFLH – LOW TO HIGH CURRENT THRESHOLD – mA 13 HCNW3120 5 VCC = 15 TO 30 V VEE = 0 V OUTPUT = OPEN 4 3 2 1 0 -40 -20 0 20 40 60 80 100 TA – TEMPERATURE – °C Figure 9. IFLH vs. Temperature. 500 400 TPLH TPHL 300 200 100 400 300 200 TPLH TPHL 100 15 30 25 20 Figure 10. Propagation Delay vs. VCC. 8 10 12 14 16 Figure 11. Propagation Delay vs. I F. 500 500 VCC = 30 V, VEE = 0 V TA = 25 °C IF = 10 mA Cg = 10 nF DUTY CYCLE = 50% f = 10 kHz 400 Tp – PROPAGATION DELAY – ns Tp – PROPAGATION DELAY – ns 6 IF – FORWARD LED CURRENT – mA VCC – SUPPLY VOLTAGE – V 300 200 TPLH TPHL 100 500 VCC = 30 V, VEE = 0 V Rg = 10 Ω, Cg = 10 nF TA = 25 °C DUTY CYCLE = 50% f = 10 kHz Tp – PROPAGATION DELAY – ns IF = 10 mA TA = 25 °C Rg = 10 Ω Cg = 10 nF DUTY CYCLE = 50% f = 10 kHz Tp – PROPAGATION DELAY – ns Tp – PROPAGATION DELAY – ns 500 0 10 20 30 40 50 Rg – SERIES LOAD RESISTANCE – Ω Figure 13. Propagation Delay vs. Rg. VCC = 30 V, VEE = 0 V TA = 25 °C IF = 10 mA Rg = 10 Ω DUTY CYCLE = 50% f = 10 kHz 400 300 200 TPLH TPHL 100 0 20 40 60 80 100 Cg – LOAD CAPACITANCE – nF Figure 14. Propagation Delay vs. Cg. 400 IF = 10 mA VCC = 30 V, VEE = 0 V Rg = 10 Ω, Cg = 10 nF DUTY CYCLE = 50% f = 10 kHz 300 200 TPLH TPHL 100 -40 -20 0 20 40 60 80 TA – TEMPERATURE – °C Figure 12. Propagation Delay vs. Temperature. 100 14 35 25 30 VO – OUTPUT VOLTAGE – V VO – OUTPUT VOLTAGE – V HCPL-3120 / HCNW3120 30 20 15 10 5 0 0 1 2 3 4 HCPL-J312 25 20 15 10 5 0 5 1 0 IF – FORWARD LED CURRENT – mA 2 3 4 5 IF – FORWARD LED CURRENT – mA Figure 15. Transfer Characteristics. 1000 TA = 25°C 100 IF – FORWARD CURRENT – mA IF – FORWARD CURRENT – mA HCPL-J312/HCNW3120 HCPL-3120 1000 IF + VF – 10 1.0 0.1 0.01 0.001 1.10 1.20 1.30 1.40 1.50 TA = 25°C 100 IF + VF – 10 1.0 0.1 0.01 0.001 1.2 1.60 VF – FORWARD VOLTAGE – VOLTS 1.3 1.4 1.5 Figure 16. Input Current vs. Forward Voltage. 1 8 0.1 µF 2 + – 7 IF = 7 to 16 mA 4V + VCC = 15 – to 30 V 3 6 IOH 4 Figure 17. I OH Test Circuit. 1.6 1.7 VF – FORWARD VOLTAGE – VOLTS 5 15 1 8 2 7 0.1 µF 3 6 1 8 2 7 0.1 µF IOL + VCC = 15 – to 30 V VOH IF = 7 to 16 mA + VCC = 15 – to 30 V 2.5 V + – 3 6 100 mA 4 5 4 Figure 18. I OL Test Circuit. 1 Figure 19. VOH Test Circuit. 8 0.1 µF 2 5 1 0.1 µF 100 mA 7 2 + VCC = 15 – to 30 V 3 6 4 5 8 0.1 µF 2 7 VO > 5 V 3 6 4 5 Figure 22. UVLO Test Circuit. VO > 5 V 3 6 4 5 Figure 21. I FLH Test Circuit. IF = 10 mA 7 IF VOL Figure 20. VOL Test Circuit. 1 8 + – VCC + VCC = 15 – to 30 V 16 1 8 0.1 µF IF = 7 to 16 mA + 10 KHz – 500 Ω 2 + – 7 IF VCC = 15 to 30 V tr tf VO 50% DUTY CYCLE 3 6 90% 10 Ω 50% VOUT 10 nF 4 10% 5 tPLH tPHL Figure 23. tPLH, t PHL, t r, and tf Test Circuit and Waveforms. VCM 1 5V δt 0.1 µF A B δV 8 IF 2 VO 3 6 4 5 VCC = 30 V VO – Figure 24. CMR Test Circuit and Waveforms. VOH SWITCH AT A: IF = 10 mA SWITCH AT B: IF = 0 mA + ∆t ∆t + – VO VCM = 1500 V VCM 0V 7 + – = VOL 17 Applications Information Eliminating Negative IGBT Gate Drive (Discussion applies to HCPL-3120, HCPL-J312, and HCNW3120) To keep the IGBT firmly off, the HCPL-3120 has a very low maximum VOL specification of 0.5 V. The HCPL-3120 realizes this very low VOL by using a DMOS transistor with 1 Ω (typical) on resistance in its pull down circuit. When the HCPL- 3120 is in the low state, the IGBT gate is shorted to the emitter by Rg + 1 Ω. Minimizing Rg and the lead inductance from the HCPL3120 to the IGBT gate and emitter (possibly by mounting the HCPL-3120 on a small PC board directly above the IGBT) can eliminate the need for negative IGBT gate drive in many applications as shown in Figure 25. Care should be taken with such a PC board design to avoid routing the IGBT collector or emitter traces close to the HCPL-3120 input as this can result in unwanted coupling of transient signals into the HCPL-3120 and degrade performance. (If the IGBT drain must be routed near the HCPL3120 input, then the LED should be reverse-biased when in the off state, to prevent the transient signals coupled from the IGBT drain from turning on the HCPL-3120.) HCPL-3120 +5 V 1 270 Ω 8 0.1 µF 2 + – VCC = 18 V + HVDC 7 Rg CONTROL INPUT 74XXX OPEN COLLECTOR 3 6 4 5 Figure 25. Recommended LED Drive and Application Circuit. Q1 3-PHASE AC Q2 - HVDC 18 Selecting the Gate Resistor (Rg) to Minimize IGBT Switching Losses. (Discussion applies to HCPL-3120, HCPLJ312 and HCNW3120) Step 1: Calculate Rg Minimum from the IOL Peak Specification. The IGBT and Rg in Figure 26 can be analyzed as a simple RC circuit with a voltage supplied by the HCPL-3120. (VCC – VEE - VOL) Rg ≥ ––––––––––––––– I OLPEAK (VCC – VEE - 2 V) = ––––––––––––––– I OLPEAK (15 V + 5 V - 2 V) = –––––––––––––––––– 2.5 A = 7.2 Ω ≅ 8 Ω The VOL value of 2 V in the previous equation is a conservative value of VOL at the peak current of 2.5A (see Figure 6). At lower Rg values the voltage supplied by the HCPL-3120 is not an ideal voltage step. This results in lower peak currents (more margin) than predicted by this analysis. When negative gate drive is not used VEE in the previous equation is equal to zero volts. HCPL-3120 +5 V 1 270 Ω 8 0.1 µF 2 + – VCC = 15 V + HVDC 7 Rg CONTROL INPUT 74XXX OPEN COLLECTOR Q1 3 6 – + 4 VEE = -5 V 3-PHASE AC 5 Q2 Figure 26. HCPL-3120 Typical Application Circuit with Negative IGBT Gate Drive. - HVDC 19 Step 2: Check the HCPL-3120 Power Dissipation and Increase Rg if Necessary. The HCPL-3120 total power dissipation (PT) is equal to the sum of the emitter power (PE ) and the output power (PO): P T = PE + PO PE = IF • VF • Duty Cycle PO = PO(BIAS) + PO (SWITCHING) = ICC• (VCC - VEE) + ESW(R G, QG) • f For the circuit in Figure 26 with IF (worst case) = 16 mA, Rg = 8 Ω, Max Duty Cycle = 80%, Qg = 500 nC, f = 20 kHz and TA max = 85C: The value of 4.25 mA for ICC in the previous equation was obtained by derating the ICC max of 5 mA (which occurs at -40°C) to ICC max at 85C (see Figure 7). Since PO for this case is greater than PO(MAX), Rg must be increased to reduce the HCPL-3120 power dissipation. PO(SWITCHING MAX) = PO(MAX) - PO(BIAS) = 178 mW - 85 mW = 93 mW PO(SWITCHINGMAX) ESW(MAX) = ––––––––––––––– f PE = 16 mA • 1.8 V • 0.8 = 23 mW PO = 4.25 mA • 20 V + 5.2 µJ• 20 kHz = 85 mW + 104 mW = 189 mW > 178 mW (PO(MAX) @ 85C = 250 mW−15C*4.8 mW/C) PE Parameter IF VF Duty Cycle Description LED Current LED On Voltage Maximum LED Duty Cycle 93 mW = ––––––– = 4.65 µW 20 kHz For Qg = 500 nC, from Figure 27, a value of E SW = 4.65 µW gives a Rg = 10.3 Ω. PO Parameter ICC VCC VEE ESW(Rg,Qg) Esw – ENERGY PER SWITCHING CYCLE – µJ f 14 Qg = 100 nC Qg = 500 nC 12 Qg = 1000 nC 10 VCC = 19 V VEE = -9 V 8 6 4 2 0 0 10 20 30 40 50 Rg – GATE RESISTANCE – Ω Figure 27. Energy Dissipated in the HCPL-3120 for Each IGBT Switching Cycle. Description Supply Current Positive Supply Voltage Negative Supply Voltage Energy Dissipated in the HCPL-3120 for each IGBT Switching Cycle (See Figure 27) Switching Frequency 20 Thermal Model (Discussion applies to HCPL-3120, HCPL-J312 and HCNW3120) The steady state thermal model for the HCPL-3120 is shown in Figure 28. The thermal resistance values given in this model can be used to calculate the temperatures at each node for a given operating condition. As shown by the model, all heat generated flows through θCA which raises the case temperature TC accordingly. The value of θCA depends on the conditions of the board design and is, therefore, determined by the designer. The value of θCA = 83°C/W was obtained from thermal measurements using a 2.5 x 2.5 inch PC board, with small traces (no ground plane), a single HCPL3120 soldered into the center of the board and still air. The absolute maximum power dissipation derating specifications assume a θCAvalue of 83°C/W. Inserting the values for θLC and θDC shown in Figure 28 gives: From the thermal mode in Figure 28 the LED and detector IC junction temperatures can be expressed as: For example, given PE = 45 mW, PO = 250 mW, TA = 70°C and θCA = 83°C/W: TJE = PE • (θLC||(θLD + θDC) + θCA) θLC * θDC + PD • –––––––––––––––– + θCA + TA θLC + θDC + θLD ( TJD = PE ) θLC • θDC ––––––––––––––– + θCA θLC + θDC + θLD ( ) + PD• (θDC||(θLD + θLC) + θCA) + TA TJE = PE • (256°C/W + θCA) + PD• (57°C/W + θCA) + TA TJD = PE • (57°C/W + θCA) + PD• (111°C/W + θCA) + TA TJE = PE• 339°C/W + PD• 140°C/W + TA = 45 mW• 339°C/W + 250 mW • 140°C/W + 70°C = 120°C TJD = PE• 140°C/W + PD• 194°C/W + TA = 45 mW• 140C/W + 250 mW • 194°C/W + 70°C = 125°C TJE and TJD should be limited to 125°C based on the board layout and part placement (θCA) specific to the application. θLD = 442 °C/W TJE TJD θLC = 467 °C/W θDC = 126 °C/W TC θCA = 83 °C/W* TA Figure 28. Thermal Model. TJE = LED junction temperature TJD = detector IC junction temperature TC = case temperature measured at the center of the package bottom θLC = LED-to-case thermal resistance θLD = LED-to-detector thermal resistance θDC = detector-to-case thermal resistance θCA = case-to-ambient thermal resistance ∗θCA will depend on the board design and the placement of the part. 21 LED Drive Circuit Considerations for Ultra High CMR Performance. (Discussion applies to HCPL3120, HCPL-J312, and HCNW3120) Without a detector shield, the dominant cause of optocoupler CMR failure is capacitive coupling from the input side of the optocoupler, through the package, to the detector IC as shown in Figure 29. The HCPL3120 improves CMR performance 1 by using a detector IC with an optically transparent Faraday shield, which diverts the capacitively coupled current away from the sensitive IC circuitry. However, this shield does not eliminate the capacitive coupling between the LED and optocoupler pins 5-8 as shown in Figure 30. This capacitive coupling causes perturbations in the LED current during common mode transients and becomes the major source of CMR failures for 8 1 7 2 CLEDP 2 CLEDO1 a shielded optocoupler. The main design objective of a high CMR LED drive circuit becomes keeping the LED in the proper state (on or off) during common mode transients. For example, the recommended application circuit (Figure 25), can achieve 15 kV/µs CMR while minimizing component complexity. Techniques to keep the LED in the proper state are discussed in the next two sections. 8 CLEDP 7 CLEDO2 3 4 CLEDN 6 3 5 4 Figure 29. Optocoupler Input to Output Capacitance Model for Unshielded Optocouplers. CLEDN SHIELD 6 5 Figure 30. Optocoupler Input to Output Capacitance Model for Shielded Optocouplers. 22 CMR with the LED On (CMRH). CMR with the LED Off (CMRL). A high CMR LED drive circuit must keep the LED on during common mode transients. This is achieved by overdriving the LED current beyond the input threshold so that it is not pulled below the threshold during a transient. A minimum LED current of 10 mA provides adequate margin over the maximum IFLH of 5 mA to achieve 15 kV/µs CMR. A high CMR LED drive circuit must keep the LED off (VF ≤ VF(OFF)) during common mode transients. For example, during a -dVcm/dt transient in Figure 31, the current flowing through CLEDP also flows through the RSAT and VSAT of the logic gate. As long as the low state voltage developed across the logic gate is less than VF(OFF), the LED will remain off and no common mode failure will occur. +5 V 1 8 0.1 µF CLEDP 2 + VSAT – The open collector drive circuit, shown in Figure 32, cannot keep the LED off during a +dVcm/dt transient, since all the current flowing through CLEDN must be supplied by the LED, and it is not recommended for applications requiring ultra high CMRL performance. Figure 33 is an alternative drive circuit which, like the recommended application circuit (Figure 25), does achieve ultra high CMR performance by shunting the LED in the off state. 7 + – VCC = 18 V 1 ILEDP 3 CLEDP ••• 6 CLEDN 4 8 +5 V 2 Rg 5 SHIELD ••• 3 Q1 7 CLEDN 6 ILEDN * THE ARROWS INDICATE THE DIRECTION OF CURRENT FLOW DURING –dVCM/dt. 4 SHIELD + – VCM Figure 31. Equivalent Circuit for Figure 25 During Common Mode Transient. 8 1 +5 V CLEDP 2 3 4 7 CLEDN SHIELD Figure 33. Recommended LED Drive Circuit for Ultra-High CMR. 6 5 Figure 32. Not Recommended Open Collector Drive Circuit. 5 23 Under Voltage Lockout Feature. (Discussion applies to HCPL-3120, HCPL-J312, and HCNW3120) The HCPL-3120 contains an under voltage lockout (UVLO) feature that is designed to protect the IGBT under fault conditions which cause the HCPL-3120 supply voltage (equivalent to the VO – OUTPUT VOLTAGE – V 14 12 (12.3, 10.8) 10 (10.7, 9.2) 8 6 4 2 0 (10.7, 0.1) 0 5 10 (12.3, 0.1) 15 20 (VCC - VEE ) – SUPPLY VOLTAGE – V Figure 34. Under Voltage Lock Out. fully-charged IGBT gate voltage) to drop below a level necessary to keep the IGBT in a low resistance state. When the HCPL-3120 output is in the high state and the supply voltage drops below the HCPL-3120 VUVLO– threshold (9.5 < VUVLO– < 12.0) the optocoupler output will go into the low state with a typical delay, UVLO Turn Off Delay, of 0.6 µs. When the HCPL-3120 output is in the low state and the supply voltage rises above the HCPL3120 VUVLO+ threshold (11.0 < VUVLO+ < 13.5) the optocoupler output will go into the high state (assumes LED is “ON”) with a typical delay, UVLO Turn On Delay of 0.8 µs. IPM Dead Time and Propagation Delay Specifications. (Discussion applies to HCPL-3120, HCPLJ312, and HCNW3120) The HCPL-3120 includes a Propagation Delay Difference (PDD) specification intended to help designers minimize “dead time” in their power inverter designs. Dead time is the time period during which both the high and low side power transistors (Q1 and Q2 in Figure 25) are off. Any overlap in Q1 and Q2 conduction will result in large currents flowing through the power devices between the high and low voltage motor rails. ILED1 ILED1 VOUT1 VOUT1 Q1 ON Q1 ON Q1 OFF Q1 OFF Q2 ON Q2 ON VOUT2 Q2 OFF VOUT2 Q2 OFF ILED2 ILED2 tPHL MIN tPHL MAX tPHL MAX tPLH MIN tPLH PDD* MAX = (tPHL- tPLH)MAX = tPHL MAX - tPLH MIN MIN tPLH MAX *PDD = PROPAGATION DELAY DIFFERENCE NOTE: FOR PDD CALCULATIONS THE PROPAGATION DELAYS ARE TAKEN AT THE SAME TEMPERATURE AND TEST CONDITIONS. (tPHL-tPLH) MAX PDD* MAX MAXIMUM DEAD TIME (DUE TO OPTOCOUPLER) = (tPHL MAX - tPHL MIN) + (tPLH MAX - tPLH MIN) = (tPHL MAX - tPLH MIN) – (tPHL MIN - tPLH MAX) = PDD* MAX – PDD* MIN Figure 35. Minimum LED Skew for Zero Dead Time. *PDD = PROPAGATION DELAY DIFFERENCE NOTE: FOR DEAD TIME AND PDD CALCULATIONS ALL PROPAGATION DELAYS ARE TAKEN AT THE SAME TEMPERATURE AND TEST CONDITIONS. HCPL-3120 OPTION 060/HCPL-J312 800 PS (mW) IS (mA) FOR HCPL-3120 OPTION 060 IS (mA) FOR HCPL-J312 700 600 500 400 300 200 100 0 0 25 50 75 100 125 150 175 200 TS – CASE TEMPERATURE – °C OUTPUT POWER – PS, INPUT CURRENT – IS OUTPUT POWER – PS, INPUT CURRENT – IS Figure 36. Waveforms for Dead Time. HCNW3120 1000 PS (mW) IS (mA) 900 800 700 600 500 400 300 200 100 0 0 25 50 75 100 125 150 175 TS – CASE TEMPERATURE – °C Figure 37. Thermal Derating Curve, Dependence of Safety Limiting Value with Case Temperature per VDE 0884. To minimize dead time in a given design, the turn on of LED2 should be delayed (relative to the turn off of LED1) so that under worst-case conditions, transistor Q1 has just turned off when transistor Q2 turns on, as shown in Figure 35. The amount of delay necessary to achieve this conditions is equal to the maximum value of the propagation delay difference specification, PDDMAX, which is specified to be 350 ns over the operating temperature range of -40°C to 100°C. Delaying the LED signal by the maximum propagation delay difference ensures that the minimum dead time is zero, but it does not tell a designer what the maximum dead time will be. The maximum dead time is equivalent to the difference between the maximum and minimum propagation delay difference specifications as shown in Figure 36. The maximum dead time for the HCPL-3120 is 700 ns (= 350 ns (-350 ns)) over an operating temperature range of -40°C to 100°C. Note that the propagation delays used to calculate PDD and dead time are taken at equal temperatures and test conditions since the optocouplers under consideration are typically mounted in close proximity to each other and are switching identical IGBTs. www.agilent.com/semiconductors For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (408) 654-8675 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6271 2451 India, Australia, New Zealand: (+65) 6271 2394 Japan: (+81 3) 3335-8152(Domestic/International), or 0120-61-1280(Domestic Only) Korea: (+65) 6271 2194 Malaysia, Singapore: (+65) 6271 2054 Taiwan: (+65) 6271 2654 Data subject to change. Copyright © 2003 Agilent Technologies, Inc. Obsoletes 5965-7875E February 10, 2003 5988-8710EN