AD AD8397

Rail-to-Rail, High Output Current Amplifier
AD8397
OUT1 1
8
+VS
–IN1 2
7
OUT2
+IN1 3
6
–IN2
–VS 4
5
+IN2
Figure 1. 8-Lead SOIC
1.50
1.25
1.00
0.75
0.50
VOUT (V)
Dual operational amplifier
Voltage feedback
Wide supply range: from 3 V to 24 V
Rail-to-rail output
Output swing to within 0.5 V of supply rails
High linear output current
310 mA peak into 32 Ω on ±12 V supplies while maintaining
−80 dBc SFDR
Low noise
4.5 nV/√Hz voltage noise density @ 100 kHz
1.5 pA/√Hz current noise density @ 100 kHz
High speed
69 MHz bandwidth (G = 1, −3 dB)
53 V/µs slew rate (RLOAD = 25 Ω)
05069-001
PIN CONFIGURATION
FEATURES
0.25
0
–0.25
Twisted-pair line drivers
Audio applications
General-purpose high current amplifiers
–0.50
–0.75
–1.00
05069-031
APPLICATIONS
–1.25
–1.50
0
GENERAL DESCRIPTION
6
8
10
12
TIME (µs)
14
16
18
20
18
20
12
9
6
3
0
–3
–6
–9
05069-032
Fabricated with ADI’s high speed eXtra Fast Complementary
Bipolar High Voltage (XFCB-HV) process, the high bandwidth
and fast slew rate of the AD8397 keep distortion to a minimum
while also dissipating minimum power. The AD8397 is available
in a standard 8-lead SOIC package and, for higher power applications, a thermally enhanced 8-lead SOIC EPAD package. Both
packages can operate from −40°C to +85°C.
4
Figure 2. Output Swing, VS = ±1.5 V, RL = 25 Ω
VOUT (V)
The AD8397 has two voltage feedback operational amplifiers
capable of driving heavy loads with excellent linearity. The
common-emitter, rail-to-rail output stage surpasses the output
voltage capability of typical emitter-follower output stages and
can swing to within 0.5 V of either rail while driving a 25 Ω
load. The low distortion, high output current, and wide output
dynamic range make the AD8397 ideal for applications that
require a large signal swing into a heavy load.
2
–12
0
2
4
6
8
10
12
TIME (µs)
14
16
Figure 3. Output Swing, VS = ±12 V, RL = 100 Ω
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703
© 2005 Analog Devices, Inc. All rights reserved.
AD8397
TABLE OF CONTENTS
Specifications..................................................................................... 3
Power Supply and Decoupling ................................................. 11
Absolute Maximum Ratings............................................................ 7
Layout Considerations............................................................... 11
Maximum Power Dissipation ..................................................... 7
Unity-Gain Output Swing ......................................................... 11
ESD Caution.................................................................................. 7
Capacitive Load Drive ............................................................... 12
Typical Performance Characteristics ............................................. 8
Outline Dimensions ....................................................................... 13
General Description ....................................................................... 11
Ordering Guide .......................................................................... 13
REVISION HISTORY
1/05—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
AD8397
SPECIFICATIONS
VS = ±1.5 V or +3 V (@ TA = 25°C, G = +1, RL = 25 Ω, unless otherwise noted).
Table 1.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
0.1 dB Flatness
Large Signal Bandwidth
Slew Rate
NOISE/DISTORTION PERFORMANCE
Distortion (Worst Harmonic)
Input Voltage Noise
Input Current Noise
DC PERFORMANCE
Input Offset Voltage
Test Conditions/Comments
Min
Max
Unit
VOUT = 0.1 V p-p
VOUT = 0.1 V p-p
VOUT = 2.0 V p-p
VOUT = 0.8 V p-p
50
3.6
9
32
MHz
MHz
MHz
V/µs
fC = 100 kHz, VOUT = 1.4 V p-p, G = +2
f = 100 kHz
f = 100 kHz
−90
4.5
1.5
dBc
nV/√Hz
pA/√Hz
81
1.0
2.5
1.0
200
1.3
50
88
∆VCM = ±1 V
−71
87
1.4
−80
kΩ
pF
dB
RLOAD = 25 Ω
RLOAD = 25 Ω
RLOAD = 100 Ω
RLOAD = 100 Ω
SFDR ≤ −70 dBc, f = 100 kHz, VOUT = 0.7 VP, RLOAD = 4.1 Ω
+1.39
0.2
+1.43
−1.4
+1.48
−1.47
170
Ω
VP
VP
VP
VP
mA
TMIN − TMAX
Input Offset Voltage Match
Input Bias Current
TMIN − TMAX
Input Offset Current
Open-Loop Gain
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Common-Mode Rejection
OUTPUT CHARACTERISTICS
Output Resistance
+Swing
−Swing
+Swing
−Swing
Maximum Output Current
POWER SUPPLY
Operating Range (Dual Supply)
Supply Current
Power Supply Rejection
Typ
VOUT = ±0.5 V
f = 100 kHz
+1.45
±1.5
6
−70
∆VS = ±0.5 V
Rev. 0 | Page 3 of 16
7
−82
2.5
2.0
900
300
−1.37
−1.44
±12.0
8.5
mV
mV
mV
nA
µA
nA
dB
V
mA/Amp
dB
AD8397
VS = ±2.5V or +5 V (@ TA = 25°C, G = +1, RL = 25 Ω, unless otherwise noted).
Table 2.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
0.1 dB Flatness
Large Signal Bandwidth
Slew Rate
NOISE/DISTORTION PERFORMANCE
Distortion (Worst Harmonic)
Input Voltage Noise
Input Current Noise
DC PERFORMANCE
Input Offset Voltage
Test Conditions/Comments
Min
Max
Unit
VOUT = 0.1 V p-p
VOUT = 0.1 V p-p
VOUT = 2.0 V p-p
VOUT = 2.0 V p-p
60
4.8
14
53
MHz
MHz
MHz
V/µs
fC = 100 kHz, VOUT = 2 V p-p, G = +2
f = 100 kHz
f = 100 kHz
−98
4.5
1.5
dBc
nV/√Hz
pA/√Hz
85
1.0
2.5
1.0
200
1.3
50
90
∆VCM = ±1 V
−76
87
1.4
−80
kΩ
pF
dB
RLOAD = 25 Ω
RLOAD = 25 Ω
RLOAD = 100 Ω
RLOAD = 100 Ω
SFDR ≤ −70 dBc, f = 100 kHz, VOUT = 1.0 VP, RLOAD = 4.3 Ω
+2.37
0.2
+2.42
−2.37
+2.48
−2.46
230
Ω
VP
VP
VP
VP
mA
TMIN − TMAX
Input Offset Voltage Match
Input Bias Current
TMIN − TMAX
Input Offset Current
Open-Loop Gain
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Common-Mode Rejection
OUTPUT CHARACTERISTICS
Output Resistance
+Swing
−Swing
+Swing
−Swing
Maximum Output Current
POWER SUPPLY
Operating Range (Dual Supply)
Supply Current
Power Supply Rejection
Typ
VOUT = ±1.0 V
f = 100 kHz
+2.45
±1.5
7
−75
∆VS = ±0.5 V
Rev. 0 | Page 4 of 16
9
−85
2.4
2.0
900
300
−2.32
−2.42
±12.6
12
mV
mV
mV
nA
µA
nA
dB
V
mA/Amp
dB
AD8397
VS = ±5 V or +10 V (@ TA = 25°C, G = +1, RL = 25 Ω, unless otherwise noted).
Table 3.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
0.1 dB Flatness
Large Signal Bandwidth
Slew Rate
NOISE/DISTORTION PERFORMANCE
Distortion (Worst Harmonic)
Input Voltage Noise
Input Current Noise
DC PERFORMANCE
Input Offset Voltage
Test Conditions/Comments
Min
Max
Unit
VOUT = 0.1 V p-p
VOUT = 0.1 V p-p
VOUT = 2.0 V p-p
VOUT = 4.0 V p-p
66
6.5
14
53
MHz
MHz
MHz
V/µs
fC = 100 kHz, VOUT = 6 V p-p, G = +2
f = 100 kHz
f = 100 kHz
−94
4.5
1.5
dBc
nV/√Hz
pA/√Hz
85
1.0
2.5
1.0
200
1.3
50
94
∆VCM = ±1 V
−84
87
1.4
−94
kΩ
pF
dB
RLOAD = 25 Ω
RLOAD = 25 Ω
RLOAD = 100 Ω
RLOAD = 100 Ω
SFDR ≤ −80 dBc, f = 100 kHz, VOUT = 3 VP, RLOAD = 12 Ω
+4.7
0.2
+4.82
−4.74
+4.96
−4.92
250
Ω
VP
VP
VP
VP
mA
TMIN − TMAX
Input Offset Voltage Match
Input Bias Current
TMIN − TMAX
Input Offset Current
Open-Loop Gain
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Common-Mode Rejection
OUTPUT CHARACTERISTICS
Output Resistance
+Swing
−Swing
+Swing
−Swing
Maximum Output Current
POWER SUPPLY
Operating Range (Dual Supply)
Supply Current
Power Supply Rejection
Typ
VOUT = ±2.0 V
f = 100 kHz
+4.92
±1.5
7
−76
∆VS = ±0.5 V
Rev. 0 | Page 5 of 16
9
−85
2.5
2.0
900
300
−4.65
−4.88
±12.6
12
mV
mV
mV
nA
µA
nA
dB
V
mA/Amp
dB
AD8397
VS = ±12 V or +24 V (@ TA = 25°C, G = +1, RL = 25 Ω, unless otherwise noted).
Table 4.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
0.1 dB Flatness
Large Signal Bandwidth
Slew Rate
NOISE/DISTORTION PERFORMANCE
Distortion (Worst Harmonic)
Input Voltage Noise
Input Current Noise
DC PERFORMANCE
Input Offset Voltage
Test Conditions/Comments
Min
Unit
69
7.6
14
53
MHz
MHz
MHz
V/µs
fC = 100 kHz, VOUT = 20 V p-p, G = +5
f = 100 kHz
f = 100 kHz
−84
4.5
1.5
dBc
nV/√Hz
pA/√Hz
90
1.0
2.5
1.0
200
1.3
50
96
∆VCM = ±1 V
−85
87
1.4
−96
kΩ
pF
dB
RLOAD = 100 Ω
RLOAD = 100 Ω
SFDR ≤ −80 dBc, f = 100 kHz, VOUT = 10 VP, RLOAD = 32 Ω
+11.82
0.2
+11.89
−11.83
310
Ω
VP
VP
mA
Input Offset Voltage Match
Input Bias Current
TMIN − TMAX
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Common-Mode Rejection
OUTPUT CHARACTERISTICS
Output Resistance
+Swing
−Swing
Maximum Output Current
POWER SUPPLY
Operating Range (Dual Supply)
Supply Current
Power Supply Rejection
Max
VOUT = 0.1 V p-p
VOUT = 0.1 V p-p
VOUT = 2.0 V p-p
VOUT = 4.0 V p-p
TMIN − TMAX
Input Offset Current
Open-Loop Gain
Typ
VOUT = ±3.0 V
f = 100 kHz
±1.5
8.5
−76
∆VS = ±0.5 V
Rev. 0 | Page 6 of 16
11
−86
3.0
2.0
900
300
−11.77
±12.6
15
mV
mV
mV
nA
µA
nA
dB
V
mA/Amp
dB
AD8397
ABSOLUTE MAXIMUM RATINGS
MAXIMUM POWER DISSIPATION
The maximum power that can be dissipated safely by
the AD8397 is limited by the associated rise in junction
temperature. The maximum safe junction temperature for
plastic encapsulated devices is determined by the glass
transition temperature of the plastic, approximately 150°C.
Temporarily exceeding this limit may cause a shift in
parametric performance due to a change in the stresses
exerted on the die by the package.
Table 5.
Rating
26.4 V
See Figure 4
−65°C to +125°C
−40°C to +85°C
300°C
150°C
4.5
1
Thermal resistance for standard JEDEC 4-layer board:
8-lead SOIC: θJA = 157.6°C/W
8-Lead SOIC EPAD: θJA = 47.2°C/W
TJ = 150°C
4.0
3.5
8-LEAD SOIC EPAD
3.0
2.5
2.0
1.5
8-LEAD SOIC
1.0
05069-020
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
MAXIMUM POWER DISSIPATION (W)
Parameter
Supply Voltage
Power Dissipation1
Storage Temperature
Operating Temperature Range
Lead Temperature Range
(Soldering 10 sec)
Junction Temperature
0.5
0
–40 –30 –20 –10 0 10 20 30 40 50 60
AMBIENT TEMPERATURE (°C)
70
80
Figure 4. Maximum Power Dissipation vs. Temperature
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate
on the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation
or loss of functionality.
Rev. 0 | Page 7 of 16
90
AD8397
TYPICAL PERFORMANCE CHARACTERISTICS
100
0
VOUT
80
–10
60
–20
–30
VIN
20
CMRR (dB)
0
–20
OUT 1
–40
OUT 2
–50
–60
–40
–70
05069-029
–60
–80
–100
0
20
40
60
80
100 120
TIME (ns)
140
160
180
05069-005
OUTPUT (mV)
40
–80
–90
0.01
200
Figure 5. Small Signal Pulse Response (G = +1, VS = ±5 V, RL = 25 Ω)
0.1
1
FREQUENCY (MHz)
10
100
Figure 8. Common-Mode Rejection vs. Frequency
(VS = ±5 V, RL = 25 Ω)
0
5
–10
4
–20
VIN
VOUT
–30
CROSSTALK (dB)
OUTPUT (V)
3
2
1
–40
–50
OUT 1
–60
–70
–80
OUT 2
05069-022
–1
0
0.2
0.4
0.6
0.8
1.0
1.2
TIME (µs)
1.4
1.6
1.8
–100
–110
0.01
2.0
6
VIN
0.1
1
FREQUENCY (MHz)
10
100
Figure 9. Output-to-Output Crosstalk vs. Frequency
(VS = ±5 V, VO = 1 V p-p, RL = 25 Ω)
Figure 6. Large Signal Pulse Response (0 V to 4 V, VS = ±5 V, RL = 25 Ω)
3.0
05069-006
–90
0
0.3
VOUT
2.5
5
2.0
4
1.5
3
1.0
2
0.5
1
0.2
GAIN (dB)
OUTPUT (V)
0
VO = 100mV p-p
–0.1
0
0
–1.0
0
40
80
120
160 200 240
TIME (ns)
280
320
360
–2
400
Figure 7. Output Overdrive Recovery
(VS = ±5 V, Gain = +2, RL = 25 Ω)
–0.3
0.1
05069-007
–0.2
–1
–0.5
05069-004
INPUT (V)
0.1
1
FREQUENCY (MHz)
Figure 10. 0.1 dB Flatness
(VS = ±5 V, VO = 0.1 V p-p, Gain = +1, RL = 25 Ω)
Rev. 0 | Page 8 of 16
10
AD8397
10
10
G = +1
0
NORMALIZED GAIN (dB)
G = +2
–10
G = +10
–20
G = +2
–10
–20
G = +10
–30
05069-008
–30
G = +1
–40
0.01
0.1
1
10
FREQUENCY (MHz)
–40
0.01
100
Figure 11. Small Signal Frequency Response for Various Gains
(VS = ±5 V, VO = 0.1 V p-p, RL = 25 Ω)
05069-011
NORMALIZED GAIN (dB)
0
0.1
1
10
FREQUENCY (MHz)
100
Figure 14. Large Signal Frequency Response for Various Gains
(VS = ±5 V, VO = 2 V p-p, RL = 25 Ω)
10
20
12V
10
0
5V
GAIN (dB)
GAIN (dB)
0
–10
–20
–10
12V
–20
2.5V
–30
0.1
1
10
FREQUENCY (MHz)
2.5V
5V
–40
0.01
100
Figure 12. Small Signal Frequency Response for Various Supplies
(Gain = +1, VO = 0.1 V p-p, RL = 25 Ω)
100
135
80
90
0
–10
–45
–90
–135
–40
0.001
0.01
0.1
1
10
FREQUENCY (MHz)
100
–180
1000
–30
PSRR (dB)
GAIN
PHASE (Degrees)
0
–40
+PSRR
–50
–PSRR
–60
05069-010
OPEN-LOOP GAIN (dB)
40
–20
100
–20
45
0
1
10
FREQUENCY (MHz)
Figure 15. Large Signal Frequency Response for Various Supplies
(Gain = +1, VO = 2 V p-p, RL = 25 Ω)
PHASE
60
20
0.1
Figure 13. Open Loop Gain and Phase vs. Frequency
(VS = ±5 V, RL = 25 Ω)
–70
–80
0.01
05069-013
–40
0.01
05069-012
05069-009
–30
0.1
1
FREQUENCY (MHz)
10
Figure 16. Power Supply Rejection
(VS = ±5 V, RL = 25 Ω)
Rev. 0 | Page 9 of 16
100
AD8397
0
–40
–10
–50
–20
–60
–40
DISTORTION (dBc)
–50
–60
–70
–80
SECOND
HARMONIC
–90
–70
–80
–90
SECOND
HARMONIC
–100
–100
–120
0.01
0.1
1
FREQUENCY (MHz)
THIRD
HARMONIC
–110
05069-023
THIRD
HARMONIC
–110
–120
0
10
1
2
3
4
5
6
7
OUTPUT VOLTAGE (V p-p)
8
9
10
Figure 20. Distortion vs. Output Voltage @ 100 kHz,
(VS = ±5 V, G = +2, RL = 25 Ω)
–40
–40
–50
–50
–60
–60
DISTORTION (dBc)
–70
–80
SECOND
HARMONIC
–90
–100
–70
–80
SECOND
HARMONIC
–90
–100
THIRD
HARMONIC
–120
0
–120
0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75
OUTPUT VOLTAGE (V p-p)
0
Figure 18. Distortion vs. Output Voltage @ 100 kHz,
(VS = ±1.5 V, G = +2, RL = 25 Ω)
–50
–60
–70
–80
SECOND
HARMONIC
–100
05069-025
–110
THIRD
HARMONIC
–120
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
OUTPUT VOLTAGE (V p-p)
4.0
4.5
2
4
6
8
10 12 14 16 18
OUTPUT VOLTAGE (V p-p)
20
22
Figure 21. Distortion vs. Output Voltage @ 100 kHz,
(VS = ±12 V, G = +5, RL = 50 Ω)
–40
–90
THIRD
HARMONIC
–110
05069-024
–110
05069-027
DISTORTION (dBc)
Figure 17. Distortion vs. Frequency
(VS = ±5 V, VO = 2 V p-p, G = +2, RL = 25 Ω)
DISTORTION (dBc)
05069-026
DISTORTION (dBc)
–30
5.0
Figure 19. Distortion vs. Output Voltage @ 100 kHz,
(VS = ±2.5 V, G = +2, RL = 25 Ω)
Rev. 0 | Page 10 of 16
24
AD8397
GENERAL DESCRIPTION
POWER SUPPLY AND DECOUPLING
The AD8397 can be powered with a good quality, wellregulated, low noise supply from ±1.5 V to ±12 V. Careful
attention should be paid to decoupling the power supply. High
quality capacitors with low equivalent series resistance (ESR),
such as multilayer ceramic capacitors (MLCCs), should be used
to minimize the supply voltage ripple and power dissipation. A
0.1 µF MLCC decoupling capacitor(s) should be located no
more than 1/8 inch away from the power supply pin(s). A large
tantalum 10 µF to 47 µF capacitor is recommended to provide
good decoupling for lower frequency signals and to supply
current for fast, large signal changes at the AD8397 outputs.
When the AD8397 is configured as a differential driver, as in
some line driving applications, a symmetrical layout should be
provided to the extent possible in order to maximize balanced
performance. When running differential signals over a long
distance, the traces on the PCB should be close together or
any differential wiring should be twisted together to minimize
the area of the inductive loop that is formed. This reduces the
radiated energy and makes the circuit less susceptible to RF
interference. Adherence to stripline design techniques for
long signal traces (greater than approximately 1 inch) is
recommended.
UNITY-GAIN OUTPUT SWING
When operating the AD8397 in a unity-gain configuration,
the output does not swing to the rails and is constrained by
the H-bridge input. This can be seen by comparing the output
overdrive recovery in Figure 7 and the input overdrive recovery
in Figure 22. To avoid overdriving the input and to realize the
full swing afforded by the rail-to-rail output stage, the amplifier
should be used in a gain of two or greater.
7
6
5
As with all high speed applications, careful attention should be
paid to printed circuit board (PCB) layout in order to prevent
associated board parasitics from becoming problematic. The
PCB should have a low impedance return path (or ground) to
the supply. Removing the ground plane from all layers in the
immediate area of the amplifier helps to reduce stray capacitances. The signal routing should be short and direct in order to
minimize the parasitic inductance and capacitance associated
with these traces. Termination resistors and loads should be
located as close as possible to their respective inputs and
outputs. Input traces should be kept as far apart as possible
from the output traces to minimize coupling (crosstalk) though
the board.
4
Rev. 0 | Page 11 of 16
VOLTS
LAYOUT CONSIDERATIONS
INPUT
OUTPUT
3
2
1
0
05069-028
The AD8397 is a voltage feedback operational amplifier which
features an H-bridge input stage and common-emitter, rail-torail output stage. The AD8397 can operate from a wide supply
range, ±1.5 V to ±12 V. When driving light loads, the rail-to-rail
output is capable of swinging to within 0.2 V of either rail. The
output can also deliver high linear output current when driving
heavy loads, up to 310 mA into 32 Ω while maintaining −80 dBc
SFDR. The AD8397 is fabricated on Analog Devices’ proprietary
eXtra Fast Complementary Bipolar High Voltage process
(XFCB-HV).
–1
0
80
160
240
320
400
480
560
640
TIME (ns)
Figure 22. Unity-Gain Input Overdrive Recovery
720
800
AD8397
CAPACITIVE LOAD DRIVE
5
390pF
470pF
0
–5
270pF
330pF
–10
–15
–20
–25
–30
05069-030
GAIN (dB)
When driving capacitive loads, many high speed operational
amplifiers exhibit peaking in their frequency response. In a
gain-of-two circuit, Figure 23 shows that the AD8397 can drive
capacitive loads up to 270 pF with only 3 dB of peaking. For
amplifiers with more limited capacitive load drive, a small series
resistor (RS) is generally used between the amplifier output and
the capacitive load in order to minimize peaking and ensure
device stability. Figure 24 shows that the use of a 2.2 Ω series
resistor can further extend the capacitive load drive of the
AD8397 out to 470 pF, while keeping the frequency response
peaking to within 3 dB.
–35
5
220pF
270pF
–40
0.01
0
–5
–20
–25
–30
05069-021
GAIN (dB)
100pF
–15
–35
0.1
1
10
FREQUENCY (MHz)
1
10
FREQUENCY (MHz)
100
Figure 24. Capacitive Load Peaking with 2.2 Ω Series Resistor
150pF
–10
–40
0.01
0.1
100
Figure 23. Capacitive Load Peaking Without Series Resistor
Rev. 0 | Page 12 of 16
AD8397
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
8
5
4.00 (0.1574)
3.80 (0.1497) 1
4
6.20 (0.2440)
5.80 (0.2284)
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
0.50 (0.0196)
× 45°
0.25 (0.0099)
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
COPLANARITY
SEATING 0.31 (0.0122)
0.10
PLANE
8°
0.25 (0.0098) 0° 1.27 (0.0500)
0.40 (0.0157)
0.17 (0.0067)
COMPLIANT TO JEDEC STANDARDS MS-012AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
Figure 25. 8-Lead Standard Small Outline Package [SOIC]
Narrow Body (R-8)
Dimensions shown in millimeters and (inches)
4.00 (0.157)
3.90 (0.154)
3.80 (0.150)
5.00 (0.197)
4.90 (0.193)
4.80 (0.189)
8
5
TOP VIEW
1
4
3.098 (0.122)
2.41 (0.095)
6.20 (0.244)
6.00 (0.236)
5.80 (0.228)
BOTTOM VIEW
1.27 (0.05)
BSC
(PINS UP)
0.50 (0.020)
× 45
0.25 (0.010)
1.75 (0.069)
1.35 (0.053)
0.25 (0.0098)
0.10 (0.0039)
COPLANARITY
SEATING
0.10
PLANE
0.51 (0.020)
0.31 (0.012)
8°
0.25 (0.0098) 0° 1.27 (0.050)
0.40 (0.016)
0.17 (0.0068)
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETER; INCHES DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 26. 8-Lead Standard Small Outline Package with Exposed Pad [SOIC_N_EP]
Narrow Body (RD-8-2)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model
AD8397ARZ1
AD8397ARZ-REEL1
AD8397ARZ-REEL71
AD8397ARDZ1
AD8397ARDZ-REEL1
AD8397ARDZ-REEL71
1
Temperature Package
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
8-Lead SOIC
8-Lead SOIC
8-Lead SOIC
8-Lead SOIC-EPAD
8-Lead SOIC-EPAD
8-Lead SOIC-EPAD
Z = Pb-free part.
Rev. 0 | Page 13 of 16
Package Outline
R-8
R-8
R-8
RD-8-2
RD-8-2
RD-8-2
AD8397
Rev. 0 | Page 14 of 16
AD8397
NOTES
Rev. 0 | Page 15 of 16
AD8397
NOTES
© 2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05069–0–1/05(0)
Rev. 0 | Page 16 of 16