AD ADP3654ARDZ-RL

High Speed, Dual,
4 A MOSFET Driver
ADP3654
FEATURES
GENERAL DESCRIPTION
Industry-standard-compatible pinout
High current drive capability
Precise UVLO comparator with hysteresis
3.3 V-compatible inputs
10 ns typical rise time and fall time at 2.2 nF load
Matched propagation delays between channels
Fast propagation delay
4.5 V to 18 V supply voltage
Parallelable dual outputs
Rated from −40°C to +125°C junction temperature
Thermally enhanced packages, 8-lead SOIC_N_EP and 8-lead
MINI_SO_EP
The ADP3654 high current and dual high speed driver is capable
of driving two independent N-channel power MOSFETs. The
driver uses the industry-standard footprint but adds high speed
switching performance.
APPLICATIONS
The driver is available in thermally enhanced SOIC_N_EP and
MINI_SO_EP packaging to maximize high frequency and
current switching in a small printed circuit board (PCB) area.
The wide input voltage range allows the driver to be compatible
with both analog and digital PWM controllers.
Digital power controllers are powered from a low voltage
supply, and the driver is powered from a higher voltage supply.
The ADP3654 driver adds UVLO and hysteresis functions,
allowing safe startup and shutdown of the higher voltage supply
when used with low voltage digital controllers.
AC-to-dc switch mode power supplies
DC-to-dc power supplies
Synchronous rectification
Motor drives
FUNCTIONAL BLOCK DIAGRAM
NC
1
ADP3654
8
NC
7
OUTA
6
VDD
5
OUTB
VDD
INA 2
PGND 3
UVLO
09054-001
INB 4
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2010 Analog Devices, Inc. All rights reserved.
ADP3654
TABLE OF CONTENTS
Features .............................................................................................. 1 Test Circuit .........................................................................................8 Applications....................................................................................... 1 Theory of Operation .........................................................................9 General Description ......................................................................... 1 Input Drive Requirements (INA and INB)................................9 Functional Block Diagram .............................................................. 1 Low-Side Drivers (OUTA, OUTB) .............................................9 Revision History ............................................................................... 2 Supply Capacitor Selection ..........................................................9 Specifications..................................................................................... 3 PCB Layout Considerations.........................................................9 Timing Diagrams.......................................................................... 3 Parallel Operation ...................................................................... 10 Absolute Maximum Ratings............................................................ 4 Thermal Considerations............................................................ 10 ESD Caution.................................................................................. 4 Outline Dimensions ....................................................................... 12 Pin Configuration and Function Descriptions............................. 5 Ordering Guide .......................................................................... 12 Typical Performance Characteristics ............................................. 6 REVISION HISTORY
8/10—Revision 0: Initial Version
Rev. 0 | Page 2 of 12
ADP3654
SPECIFICATIONS
VDD = 12 V, TJ = −40°C to +125°C, unless otherwise noted. 1
Table 1.
Parameter
SUPPLY
Supply Voltage Range
Supply Current
UVLO
Turn-On Threshold Voltage
Turn-Off Threshold Voltage
Hysteresis
DIGITAL INPUTS (INA, INB)
Input Voltage High
Input Voltage Low
Input Current
Internal Pull-Up/Pull-Down Current
OUTPUTS (OUTA, OUTB)
Output Resistance, Unbiased
Peak Source Current
Peak Sink Current
SWITCHING TIME
OUTA and OUTB Rise Time
OUTA and OUTB Fall Time
OUTA and OUTB Rising Propagation Delay
OUTA and OUTB Falling Propagation Delay
Delay Matching Between Channels
1
Symbol
Test Conditions/Comments
VDD
IDD
No switching
VUVLO_ON
VUVLO_OFF
VDD rising, TJ = 25°C, see Figure 3
VDD falling, TJ = 25°C, see Figure 3
3.8
3.5
VIH
VIL
IIN
See Figure 2
See Figure 2
0 V < VIN < VDD
2.0
tRISE
tFALL
tD1
tD2
Min
18
3
V
mA
4.5
4.3
V
V
V
6
VDD = PGND
See Figure 14
See Figure 14
80
4
−4
kΩ
A
A
CLOAD = 2.2 nF, see Figure 2
CLOAD = 2.2 nF, see Figure 2
CLOAD = 2.2 nF, see Figure 2
CLOAD = 2.2 nF, see Figure 2
10
10
14
22
2
0.8
+20
−20
VIL
tRISE
tD2
tFALL
90%
90%
09054-002
10%
10%
Figure 2. Output Timing Diagram
VUVLO_ON
VUVLO_OFF
NORMAL OPERATION
OUTPUTS DISABLED
UVLO MODE
OUTPUTS DISABLED
Figure 3. UVLO Function
Rev. 0 | Page 3 of 12
09054-003
VDD
UVLO MODE
1.2
V
V
μA
μA
VIH
OUTA,
OUTB
Unit
4.2
3.9
0.3
TIMING DIAGRAMS
tD1
Max
4.5
All limits at temperature extremes guaranteed via correlation using standard statistical quality control (SQC) methods.
INA,
INB
Typ
25
25
30
35
ns
ns
ns
ns
ns
ADP3654
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
VDD
OUTA, OUTB
DC
<200 ns
INA, INB
ESD
Human Body Model (HBM)
Field Induced Charged Device Model
(FICDM)
SOIC_N_EP
MINI_SO_EP
θJA, JEDEC 4-Layer Board
SOIC_N_EP1
MINI_SO_EP1
Junction Temperature Range
Storage Temperature Range
Lead Temperature
Soldering (10 sec)
Vapor Phase (60 sec)
Infrared (15 sec)
1
Rating
−0.3 V to +20 V
−0.3 V to VDD + 0.3 V
−2 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
3.5 kV
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
1.5 kV
1.0 kV
59°C/W
43°C/W
−40°C to +150°C
−65°C to +150°C
300°C
215°C
260°C
θJA is measured per JEDEC standards, JESD51-2, JESD51-5, and JESD51-7, as
appropriate with the exposed pad soldered to the PCB.
Rev. 0 | Page 4 of 12
ADP3654
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
NC 1
8
ADP3654
NC
OUTA
TOP VIEW
PGND 3 (Not to Scale) 6 VDD
INB 4
5 OUTB
7
NOTES
1. NC = NO CONNECT.
2. THE EXPOSED PAD OF THE PACKAGE IS NOT DIRECTLY
CONNECTED TO ANY PIN OF THE PACKAGE, BUT IT IS
ELECTRICALLY AND THERMALLY CONNECTED TO THE DIE
SUBSTRATE, WHICH IS THE GROUND OF THE DEVICE. IT IS
RECOMMENDED TO HAVE THE EXPOSED PAD AND THE
PGND PIN CONNECTED ON THE PCB.
09054-004
INA 2
Figure 4. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
Mnemonic
NC
INA
PGND
INB
OUTB
VDD
OUTA
NC
EPAD
Description
No Connect.
Input Pin for Channel A Gate Driver.
Ground. This pin should be closely connected to the source of the power MOSFET.
Input Pin for Channel B Gate Driver.
Output Pin for Channel B Gate Driver.
Power Supply Voltage. Bypass this pin to PGND with a ~1 μF to 5 μF ceramic capacitor.
Output Pin for Channel A Gate Driver.
No Connect.
Exposed Pad. The exposed pad of the package is not directly connected to any pin of the package, but it is
electrically and thermally connected to the die substrate, which is the ground of the device. It is recommended
to have the exposed pad and the PGND pin connected on the PCB.
Rev. 0 | Page 5 of 12
ADP3654
TYPICAL PERFORMANCE CHARACTERISTICS
VDD = 12 V, TJ = 25°C, unless otherwise noted.
25
9
V UVLO_ON
8
20
V UVLO_OFF
TIME (ns)
6
15
tFALL
10
tRISE
5
5
4
–30
–10
10
30
50
70
TEMPERATURE (°C)
90
110
130
0
09054-005
3
–50
0
Figure 5. UVLO vs. Temperature
5
10
VDD (V)
15
20
09054-008
UVLO (V)
7
Figure 8. Rise and Fall Times vs. VDD
70
14
60
12
tFALL
50
10
TIME (ns)
TIME (ns)
tRISE
8
6
40
30
tD2
20
4
tD1
–30
–10
10
30
50
70
TEMPERATURE (°C)
90
110
130
0
09054-006
0
–50
0
Figure 6. Rise and Fall Times vs. Temperature
5
10
VDD (V)
15
20
Figure 9. Propagation Delay vs. VDD
60
VDD = 12V
50
OUTA/OUTB
30
tD2
2
20
tD1
INA/INB
0
–50
–30
–10
10
30
50
70
TEMPERATURE (°C)
90
110
130
1
Figure 7. Propagation Delay vs. Temperature
VDD = 12V
TIME = 20ns/DIV
Figure 10. Typical Rise Propagation Delay
Rev. 0 | Page 6 of 12
09054-010
10
09054-007
TIME (ns)
40
09054-009
10
2
ADP3654
OUTA/OUTB
OUTA/OUTB
2
INA/INB
INA/INB
1
Figure 11. Typical Fall Propagation Delay
Figure 13. Typical Fall Time
OUTA/OUTB
2
VDD = 12V
TIME = 20ns/DIV
09054-012
INA/INB
1
VDD = 12V
TIME = 20ns/DIV
Figure 12. Typical Rise Time
Rev. 0 | Page 7 of 12
09054-013
VDD = 12V
TIME = 20ns/DIV
09054-011
1
2
ADP3654
TEST CIRCUIT
1
2
NC
INA
NC 8
SCOPE
PROBE
ADP3654
A
OUTA
7
VDD
3 PGND
VDD 6
4.7µF
CERAMIC
INB
B
OUTB
CLOAD
5
09054-014
4
100nF
CERAMIC
Figure 14. Test Circuit
Rev. 0 | Page 8 of 12
ADP3654
THEORY OF OPERATION
The ADP3654 dual driver is optimized for driving two
independent enhancement N-channel MOSFETs or insulated
gate bipolar transistors (IGBTs) in high switching frequency
applications.
LOW-SIDE DRIVERS (OUTA, OUTB)
These applications require high speed, fast rise and fall times, as
well as short propagation delays. The capacitive nature of the
aforementioned gated devices requires high peak current
capability as well.
When ADP3654 is disabled, both low-side gates are held low.
Internal impedance is present between the OUTA pin and GND
and between the OUTB pin and GND; this feature ensures that
the power MOSFET is normally off when bias voltage is not
present.
1
2
NC
INA
NC
8
ADP3654
A
VDS
OUTA
When interfacing ADP3654 to external MOSFETs, the designer
should consider ways to make a robust design that minimizes
stresses on both the driver and the MOSFETs. These stresses
include exceeding the short time duration voltage ratings on the
OUTA and OUTB pins, as well as the external MOSFET.
7
VDD
3
PGND
VDD
6
VDS
INB
B
OUTB
Power MOSFETs are usually selected to have a low on resistance
to minimize conduction losses, which usually implies a large
input gate capacitance and gate charge.
5
SUPPLY CAPACITOR SELECTION
09054-015
4
The ADP3654 dual drivers are designed to drive ground
referenced N-channel MOSFETs. The bias is internally
connected to the VDD supply and PGND.
INPUT DRIVE REQUIREMENTS (INA AND INB)
For the supply input (VDD) of the ADP3654, a local bypass
capacitor is recommended to reduce the noise and to supply
some of the peak currents that are drawn.
The ADP3654 is designed to meet the requirements of modern
digital power controllers; the signals are compatible with 3.3 V
logic levels. At the same time, the input structure allows for
input voltages as high as VDD.
An improper decoupling can dramatically increase the rise
times because excessive resonance on the OUTA and OUTB
pins can, in some extreme cases, damage the device, due to
inductive overvoltage on the VDD, OUTA, or OUTB pin.
An internal pull-down resistor is present at the input, which
guarantees that the power device is off in the event that the
input is left floating.
The minimum capacitance required is determined by the size
of the gate capacitances being driven, but as a general rule, a
4.7 μF, low ESR capacitor should be used. Multilayer ceramic
chip (MLCC) capacitors provide the best combination of low
ESR and small size. Use a smaller ceramic capacitor (100 nF)
with a better high frequency characteristic in parallel to the
main capacitor to further reduce noise.
Figure 15. Typical Application Circuit
Keep the ceramic capacitor as close as possible to the ADP3654
device and minimize the length of the traces going from the
capacitor to the power pins of the device.
PCB LAYOUT CONSIDERATIONS
Use the following general guidelines when designing PCBs:
•
•
•
•
•
Rev. 0 | Page 9 of 12
Trace out the high current paths and use short, wide
(>40 mil) traces to make these connections.
Minimize trace inductance between the OUTA and OUTB
outputs and MOSFET gates.
Connect the PGND pin of the ADP3654 device as closely
as possible to the source of the MOSFETs.
Place the VDD bypass capacitor as close as possible to the
VDD and PGND pins.
Use vias to other layers, when possible, to maximize
thermal conduction away from the IC.
ADP3654
Figure 16 shows an example of the typical layout based on the
preceding guidelines.
THERMAL CONSIDERATIONS
When designing a power MOSFET gate drive, the maximum
power dissipation in the driver must be considered to avoid
exceeding maximum junction temperature.
Data on package thermal resistance is provided in Table 2 to
help the designer with this task.
09054-016
There are several equally important aspects that must be
considered, such as the following:
Figure 16. External Component Placement Example
Note that the exposed pad of the package is not directly connected to any pin of the package, but it is electrically and
thermally connected to the die substrate, which is the ground
of the device.
PARALLEL OPERATION
The two driver channels present in the ADP3654 device can be
combined to operate in parallel to increase drive capability and
minimize power dissipation in the driver.
The connection scheme is shown in Figure 17. In this configuration, INA and INB are connected together, and OUTA and
OUTB are connected together.
Particular attention must be paid to the layout in this case to
optimize load sharing between the two drivers.
1
NC
NC
•
•
•
•
•
•
All of these factors influence and limit the maximum allowable
power dissipated in the driver.
The gate of a power MOSFET has a nonlinear capacitance
characteristic. For this reason, although the input capacitance
is usually reported in the MOSFET data sheet as CISS, it is not
useful to calculate power losses.
The total gate charge necessary to turn on a power MOSFET
device is usually reported on the device data sheet under QG.
This parameter varies from a few nanocoulombs (nC) to several
hundred nC, and is specified at a specific VGS value (10 V
or 4.5 V).
The power necessary to charge and then discharge the gate of a
power MOSFET can be calculated as:
8
PGATE = VGS × QG × fSW
ADP3654
2
INA
A
OUTA
where:
VGS is the bias voltage powering the driver (VDD).
QG is the total gate charge.
fSW is the maximum switching frequency.
7
VDD
3
PGND
VDD
6
VDS
INB
B
OUTB
5
09054-017
4
Figure 17. Parallel Operation
Gate charge of the power MOSFET being driven
Bias voltage value used to power the driver
Maximum switching frequency of operation
Value of external gate resistance
Maximum ambient (and PCB) temperature
Type of package
The power dissipated for each gate (PGATE) still needs to be
multiplied by the number of drivers (in this case, 1 or 2) being
used in each package, and it represents the total power dissipated in charging and discharging the gates of the power
MOSFETs.
Not all of this power is dissipated in the gate driver because part
of it is actually dissipated in the external gate resistor, RG. The
larger the external gate resistor is, the smaller the amount of
power that is dissipated in the gate driver.
In modern switching power applications, the value of the gate
resistor is kept at a minimum to increase switching speed and
minimize switching losses.
In all practical applications where the external resistor is in the
order of a few ohms, the contribution of the external resistor
can be neglected, and the extra loss is assumed in the driver,
providing a good guard band to the power loss calculations.
Rev. 0 | Page 10 of 12
ADP3654
The SOIC_N_EP thermal resistance is 59°C/W.
In addition to the gate charge losses, there are also dc bias
losses, due to the bias current of the driver. This current is
present regardless of the switching.
ΔTJ = 878.4 mW × 59°C/W = 51.8°C
TJ = TA + ΔTJ = 136.8°C ≤ TJMAX
PDC = VDD × IDD
This estimated junction temperature does not factor in the
power dissipated in the external gate resistor and, therefore,
provides a certain guard band.
The total estimated loss is the sum of PDC and PGATE.
PLOSS = PDC + (n × PGATE)
If a lower junction temperature is required by the design,
the MINI_SO_EP package can be used, which provides a
thermal resistance of 43°C/W, so that the maximum junction
temperature is
where n is the number of gates driven.
When the total power loss is calculated, the temperature
increase can be calculated as
ΔTJ = PLOSS × θJA
ΔTJ = 878.4 mW × 43°C/W = 37.7°C
Design Example
For example, consider driving two IRFS4310Z MOSFETs with a
VDD of 12 V at a switching frequency of 300 kHz, using an
ADP3654 in the SOIC_N_EP package.
The maximum PCB temperature considered for this design is 85°C.
TJ = TA + ΔTJ = 122.7°C ≤ TJMAX
Other options to reduce power dissipation in the driver include
reducing the value of the VDD bias voltage, reducing switching frequency, and choosing a power MOSFET with smaller gate charge.
From the MOSFET data sheet, the total gate charge is QG = 120 nC.
PGATE = 12 V × 120 nC × 300 kHz = 432 mW
PDC = 12 V × 1.2 mA = 14.4 mW
PLOSS = 14.4 mW + (2 × 432 mW) = 878.4 mW
Rev. 0 | Page 11 of 12
ADP3654
OUTLINE DIMENSIONS
5.00 (0.197)
4.90 (0.193)
4.80 (0.189)
4.00 (0.157)
3.90 (0.154)
3.80 (0.150)
8
2.29 (0.090)
5
2.29 (0.090)
6.20 (0.244)
6.00 (0.236)
5.80 (0.228)
TOP VIEW
1
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
4
BOTTOM VIEW
1.27 (0.05)
BSC
(PINS UP)
1.75 (0.069)
1.35 (0.053)
1.65 (0.065)
1.25 (0.049)
0.10 (0.004)
MAX
COPLANARITY
0.10
SEATING
PLANE
0.51 (0.020)
0.31 (0.012)
0.50 (0.020)
0.25 (0.010)
0.25 (0.0098)
0.17 (0.0067)
45°
1.27 (0.050)
0.40 (0.016)
8°
0°
COMPLIANT TO JEDEC STANDARDS MS-012-A A
072808-A
CONTROLLING DIMENSIONS ARE IN MILLIMETER; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 18. 8-Lead Standard Small Outline Package, with Exposed Pad [SOIC_N_EP]
Narrow Body (RD-8-1)
Dimensions shown in millimeters and (inches)
3.10
3.00
2.90
5
8
TOP
VIEW
1
EXPOSED
PAD
4
PIN 1
INDICATOR
0.525 BSC
0.65 BSC
0.94
0.86
0.78
0.15
0.10
0.05
COPLANARITY
0.10
5.05
4.90
4.75
1.10 MAX
SEATING
PLANE
0.40
0.33
0.25
BOTTOM VIEW
1.83
1.73
1.63
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
0.23
0.18
0.13
8°
0°
0.70
0.55
0.40
COMPLIANT TO JEDEC STANDARDS MO-187-AA-T
071008-A
3.10
3.00
2.90
2.26
2.16
2.06
Figure 19. 8-Lead Mini Small Outline Package with Exposed Pad [MINI_SO_EP]
(RH-8-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
ADP3654ARDZ-RL
UVLO
Option
4.5 V
Temperature
Range
−40°C to +125°C
ADP3654ARHZ-RL
4.5 V
−40°C to +125°C
1
Package Description
8-Lead Standard Small Outline Package
(SOIC_N_EP), 13“ Tape and Reel
8-Lead Mini Small Outline Package (MINI_SO_EP),
13” Tape and Reel
Z = RoHS Compliant Part.
©2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09054-0-8/10(0)
Rev. 0 | Page 12 of 12
Package
Option
RD-8-1
Ordering
Quantity
2,500
Branding
RH-8-1
3,000
78