AD AD8475

Precision, Selectable Gain,
Fully Differential Funnel Amplifier
AD8475
13 –VS
14 –VS
15 –VS
16 +IN 0.4x
1.25kΩ
+IN 0.8x 2
11 –OUT
AD8475
1.25kΩ
–IN 0.8x 3
12 NC
1.25kΩ
10 +OUT
1.25kΩ
1kΩ
–IN 0.4x 4
+VS 8
+VS 7
+VS 6
–OUT
NC
7
6
–VS
Figure 1. 16-Lead LFCSP
1kΩ
The AD8475 comes with two standard pin-selectable gain
options: 0.4 and 0.8. The gain of the part is set by driving the
input pin corresponding to the appropriate gain.
The AD8475 also provides overvoltage protection from large
industrial input voltages up to ±15 V while operating on a single
5 V supply. The VOCM pin adjusts the output voltage common
mode for precision level shifting, to match the ADC’s input range
and maximize dynamic range.
+OUT 5
1.25kΩ
VOCM 4
AD8475
+VS 3
1.25kΩ
1.25kΩ
–IN 0.4x 2
The AD8475 is a fully differential, attenuating amplifier with
integrated precision gain resistors. It provides precision attenuation
(by 0.4 or 0.8), common-mode level shifting, and single-ended-todifferential conversion along with input overvoltage protection.
Power dissipation on a single 5 V supply is only 16 mW.
–IN 0.8x 1
1.25kΩ
NC = NO CONNECT
09432-002
1kΩ
GENERAL DESCRIPTION
The AD8475 is a simple to use, fully integrated precision gain
block, designed to process signal levels of up to ±10 V on a single
supply. It provides a complete interface to make industrial level
signals directly compatible with the differential input ranges of low
voltage high performance 16-bit or 18-bit single-supply successive
approximation (SAR) analog-to-digital converters (ADCs).
VOCM
09432-001
NC = NO CONNECT
–IN 0.4x 5
9
8
ADC drivers
Differential instrumentation amplifier building blocks
Single-ended-to-differential converters
1kΩ
+IN 0.4x 1
+IN 0.4x
APPLICATIONS
FUNCTIONAL BLOCK DIAGRAMS
9
Precision attenuation: G = 0.4, G = 0.8
Fully differential or single-ended input/output
Differential output designed to drive precision ADCs
Drives switched capacitor and Σ-Δ ADCs
Rail-to-rail output
VOCM pin adjusts output common mode
Robust overvoltage protection up to ±15 V (VS = +5 V)
Single supply: 3 V to 10 V
Dual supplies: ±1.5 V to ±5 V
High performance
Suited for driving 18-bit converter up to 4 MSPS
10 nV/√Hz output noise
3 ppm/°C gain drift
500 μV maximum output offset
50 V/μs slew rate
Low power: 3.2 mA supply current
10 +IN 0.8x
FEATURES
Figure 2. 10-Lead MSOP
The AD8475 works extremely well with SAR, Σ-Δ, and pipeline
converters. The high current output stage of the part allows it to
drive the switched capacitor front-end circuits of many ADCs with
minimal error.
Unlike many differential drivers in the market, the AD8475 is a
high precision amplifier. With 500 μV maximum output offset,
10 nV/√Hz output noise, and −112 dB THD + N, the AD8475
pairs well with high accuracy converters. Considering its low power
consumption and high precision, the slew-enhanced AD8475 has
excellent speed, settling to 18-bit precision for 4 MSPS acquisition.
The AD8475 is available in a space-saving 16-lead 3 mm × 3 mm
LFCSP package and a 10-lead MSOP package. It is fully specified
over the −40°C to +85°C temperature range.
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2010–2011 Analog Devices, Inc. All rights reserved.
AD8475
TABLE OF CONTENTS
Features .............................................................................................. 1 Circuit Information.................................................................... 17 Applications....................................................................................... 1 DC Precision ............................................................................... 17 General Description........................................................................... 1 Input Voltage Range................................................................... 18 Functional Block Diagrams............................................................. 1 Driving the AD8475................................................................... 18 Revision History ............................................................................... 2 Power Supplies ............................................................................ 18 Specifications..................................................................................... 3 Applications Information .............................................................. 19 Absolute Maximum Ratings............................................................ 5 Typical Configuration................................................................ 19 Thermal Resistance ...................................................................... 5 Single-Ended to Differential Conversion................................ 19 ESD Caution.................................................................................. 5 Setting the Output Common-Mode Voltage .......................... 19 Pin Configurations and Function Descriptions ........................... 6 High Performance ADC Driving ............................................. 20 Typical Performance Characteristics ............................................. 8 AD8475 Evaluation Board ............................................................ 22 Terminology .................................................................................... 16 Outline Dimensions ....................................................................... 23 Theory of Operation ...................................................................... 17 Ordering Guide .......................................................................... 24 Overview...................................................................................... 17 REVISION HISTORY
4/11—Rev. A to Rev. B
Added B Grade Columns to Specifications Section..................... 3
Changes to Figure 16........................................................................ 9
Changes to Figure 43...................................................................... 14
Changes to Ordering Guide .......................................................... 24
1/11—Rev. 0 to Rev. A
Added 16-Lead LFCSP.................................................. Throughout
Changes to Table 1 and Note 3........................................................ 3
Change to Table 2 ............................................................................. 5
Added Figure 3 and Table 4; Renumbered Sequentially ............. 6
Changes to Typical Performance Characteristics Format........... 8
Added AD8475 Evaluation Board Section and Figure 56......... 22
10/10—Revision 0: Initial Version
Rev. B | Page 2 of 24
AD8475
SPECIFICATIONS
VS = 5 V, G = 0.4, VOCM connected to 2.5 V, RL = 1 kΩ differentially, TA = 25°C, referred to output (RTO), unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
−3 dB Small Signal
Bandwidth
−3 dB Large Signal
Bandwidth
Slew Rate
Settling Time to 0.01%
Settling Time to 0.001%
NOISE/DISTORTION 1
THD + N
HD2
HD3
IMD3
IMD3
Output Voltage Noise
Spectral Noise Density
GAIN
Gain Error
Gain Drift
Gain Nonlinearity
OFFSET AND CMRR
Offset 2
vs. Temperature
vs. Power Supply
Common-Mode Rejection
Ratio
INPUT CHARACTERISTICS
Input Voltage Range 3
Impedance 4
Single-Ended Input
Differential Input
Common Mode Input
OUTPUT CHARACTERISTICS
Output Swing
Output Balance Error
Output Impedance
Capacitive Load
Short-Circuit Current Limit
VOCM CHARACTERISTICS
VOCM Input Voltage Range
VOCM Input Impedance
VOCM Gain Error
Test Conditions/Comments
Min
B Grade
Typ
Max
Min
A Grade
Typ
Max
Unit
150
150
MHz
15
15
MHz
2 V step
2 V step on output
2 V step on output
50
45
50
50
45
50
V/μs
ns
ns
f = 100 kHz, VOUT = 4 V p-p,
22 kHz band-pass filter
f = 1 MHz, VOUT = 2 V p-p
f = 1 MHz, VOUT = 2 V p-p
f1 = 0.95 MHz, f2 = 1.05 MHz,
VOUT = 2 V p-p
f1 = 95 kHz, f2 = 105 kHz,
VOUT = 2 V p-p
f = 0.1 Hz to 10 Hz
f = 1 kHz
−112
−112
dB
−110
−96
−90
−110
−96
−90
dB
dB
dBc
−84
−84
dBc
2.5
10
0.4
2.5
10
0.4
μV p-p
nV/√Hz
V/V
%
ppm/°C
ppm
RL = ∞
−40°C ≤ TA ≤ +85°C
VOUT = 4 V p-p
RTO
−40°C ≤ TA ≤ +85°C
VS = ±2.5 V to ±5 V
VINcm = ±5 V
Differential input
Single-ended input
VINcm = VS/2
1
2.5
50
2.5
0.02
3
1
2.5
200
90
86
50
2.5
−6.25
−12.5
+6.25
+12.5
−VS +
0.05
90
−6.25
−12.5
+VS −
0.05
−VS + 1
+6.25
+12.5
V
V
−VS +
0.05
−80
kΩ
kΩ
kΩ
+VS −
0.05
dB
Ω
pF
mA
0.1
30
110
+VS
100
−VS + 1
+VS
100
0.02
Rev. B | Page 3 of 24
μV
μV/°C
dB
dB
2.92
5
1.75
0.1
30
110
Per output
500
90
76
2.92
5
1.75
∆VOUT,cm/∆VOUT,dm
0.05
3
0.02
V
kΩ
%
AD8475
Parameter
POWER SUPPLY
Specified Voltage
Operating Voltage Range
Supply Current
Over Temperature
TEMPERATURE RANGE
Specified Performance Range
Operating Range
Test Conditions/Comments
Min
B Grade
Typ
Max
Min
5
3
3
−40°C ≤ TA ≤ +85°C
−40
−40
1
Includes amplifier voltage and current noise, as well as noise of internal resistors.
Includes input bias and offset current errors.
3
The input voltage range is a function of the voltage supplies and ESD diodes.
4
Internal resistors are trimmed to be ratio matched but have ±20% absolute accuracy.
2
Rev. B | Page 4 of 24
A Grade
Typ
Max
5
10
3.2
4
3
+85
+125
−40
−40
3
Unit
10
3.2
4
V
V
mA
mA
+85
+125
°C
°C
AD8475
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 2.
Parameter
Supply Voltage
Maximum Voltage at Any Input Pin
Minimum Voltage at Any Input Pin
Storage Temperature Range
Specified Temperature Range
Operating Temperature Range
Junction Temperature
ESD (FICDM)
ESD (HBM)
Rating
11 V
+VS + 10.5 V
−VS − 16 V
−65°C to +150°C
−40°C to +85°C
−40°C to +125°C
150°C
1500 V
2000 V
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 3. Thermal Resistance
Package Type
16-Lead LFCSP (Exposed Pad)
10-Lead MSOP
ESD CAUTION
Stresses above those listed under Absolute Maximum
Ratings may cause permanent damage to the device. This is
a stress rating only; functional operation of the device at
these or any other conditions above those indicated in the
operational section of this specification is not implied.
Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
Rev. B | Page 5 of 24
θJA
84.90
214.0
Unit
°C/W
°C/W
AD8475
13 –VS
14 –VS
15 –VS
16 +IN 0.4x
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
+IN 0.4x 1
12 NC
+IN 0.8x 2
AD8475
11 –OUT
–IN 0.8x 3
TOP VIEW
(Not to Scale
10 +OUT
–IN 0.4x 4
NOTES
1. NC = NO CONNECT.
2. SOLDER THE EXPOSED PADDLE ON THE BACK
OF THE PACKAGE TO A GROUND PLANE.
09432-003
+VS 8
+VS 6
+VS 7
–IN 0.4x 5
9 VOCM
Figure 3. 16-Lead LFCSP Pin Configuration
Table 4. 16-Lead LFCSP Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Mnemonic
+IN 0.4x
+IN 0.8x
−IN 0.8x
−IN 0.4x
−IN 0.4x
+VS
+VS
+VS
VOCM
+OUT
−OUT
NC
−VS
−VS
−VS
+IN 0.4x
EPAD
Description
Positive Input for 0.4 Attenuation.
Positive Input for 0.8 Attenuation
Negative Input for 0.8 Attenuation.
Negative Input for 0.4 Attenuation.
Negative Input for 0.4 Attenuation.
Positive Supply.
Positive Supply.
Positive Supply.
Output Common-Mode Adjust.
Positive Output.
Negative Output.
No Connect.
Negative Supply.
Negative Supply.
Negative Supply.
Positive Input for 0.4 Attenuation.
Solder the exposed paddle on the back of the package to a ground plane.
Rev. B | Page 6 of 24
AD8475
–IN 0.4x 2
10 +IN 0.8x
9
+IN 0.4x
8
–VS
VOCM 4
7
NC
+OUT 5
6
–OUT
+VS 3
AD8475
TOP VIEW
(Not to Scale
NC = NO CONNECT
09432-004
–IN 0.8x 1
Figure 4. 10-Lead MSOP Pin Configuration
Table 5. 10-Lead MSOP Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
Mnemonic
−IN 0.8x
−IN 0.4x
+VS
VOCM
+OUT
−OUT
NC
−VS
+IN 0.4x
+IN 0.8x
Description
Negative Input for 0.8 Attenuation
Negative Input for 0.4 Attenuation
Positive Supply
Output Common-Mode Adjust
Noninverting Output
Inverting Output
No Connect
Negative Supply
Positive Input for 0.4 Attenuation
Positive Input for 0.8 Attenuation
Rev. B | Page 7 of 24
AD8475
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, VS = 5 V, gain = 0.4, RLOAD = 1 kΩ, RTO, unless otherwise specified.
10
REPRESENTATIVE SAMPLES
800
–4.97V, +7.75V
G = 0.8
400
VOSO (µV)
COMMON-MODE VOLTAGE (V)
600
200
G = 0.4
0
–200
–400
–600
4
+4.95V, +7.75V
–2.97V, +3.25V
0V, +3.25V
+2.95V, +3.25V
2
0
VS = +3V, VOCM = +1.5V
–2
–4
0V, –3.75V
–2.97V, –3.75V
–20
0
20
40
60
80
100
120
TEMPERATURE (°C)
0V, –6.25V
–4.97V, –6.25V
–8
–5.5 –4.5 –3.5 –2.5 –1.5 –0.5 0.5
09432-006
–1000
–40
+2.95V, –3.75V
+4.95V, –6.25V
1.5
2.5
3.5
4.5
5.5
OUTPUT VOLTAGE (V)
Figure 8. Input Common-Mode Voltage vs. Output Voltage,
VS = +5 V and +3 V
Figure 5. System Offset vs. Temperature
150
REPRESENTATIVE SAMPLES
4
VIN = ±5V
REPRESENTATIVE SAMPLES
100
3
GAIN ERROR (µV/V)
2
CMRR (µV/V)
0V, +7.75V
6
–6
–800
5
VS = +5V, VOCM = +2.5V
8
09432-008
1000
1
0
–1
–2
–3
50
0
–50
–100
–20
0
20
40
60
80
100
120
TEMPERATURE (°C)
–150
–40
09432-005
–5
–40
20
40
60
80
100
120
Figure 9. Gain Error vs. Temperature, VS = ±5 V
130
65
125
SHORT-CIRCUIT CURRENT (mA)
60
55
50
FALL
40
30
–40
RISE
120
115
110
105
100
95
90
85
–20
0
20
40
60
80
TEMPERATURE (°C)
100
120
80
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
Figure 10. Short-Circuit Current vs. Temperature
Figure 7. Slew Rate vs. Temperature
Rev. B | Page 8 of 24
120
09432-016
35
09432-015
SLEW RATE (V/µs)
0
TEMPERATURE (°C)
Figure 6. CMRR vs. Temperature (G = 0.8)
45
–20
09432-100
–4
–40°C
+25°C
+85°C
+105°C
+125°C
10k
100k
1M
RLOAD (Ω)
Figure 11. Output Voltage Swing vs. RLOAD vs. Temperature,
VS = ±5 V and +5 V
1.0
0.8
0.6
0.4
0.2
–VS
10µA
100µA
1mA
10mA
100mA
OUTPUT CURRENT (A)
Figure 14. Output Voltage Swing vs. Output Current vs. Temperature,
VS = ±5 V and +5 V
10
MAXIMUM OUTPUT VOLTAGE ( V p-p)
0.8 × VIN
09432-051
2V/DIV
VOUT
100µs/DIV
9
8
7
6
5
4
3
2
1
0
100
1k
10k
100k
1M
09432-012
1k
–40°C
+25°C
+85°C
+105°C
+125°C
10M
FREQUENCY (Hz)
Figure 15. Maximum Output Voltage vs. Frequency
100
–30
90
G = 0.8
–40
80
G = 0.4
–50
70
CMRR (dB)
–20
–60
–70
60
50
–80
40
–90
30
–100
100k
1M
10M
FREQUENCY (Hz)
09432-011
PSRR (dB)
Figure 12. Overdrive Recovery
Figure 13. Power Supply Rejection Ratio (PSRR) vs. Frequency
20
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 16. CMRR vs. Frequency
Rev. B | Page 9 of 24
10M
100M
09432-216
1.0
0.8
0.6
0.4
0.2
–VS
100
+VS
0.2
0.4
0.6
0.8
1.0
09432-014
OUTPUT VOLTAGE SWING (V)
REFERRED TO SUPPLY VOLTAGES
+VS
0.2
0.4
0.6
0.8
1.0
09432-013
OUTPUT VOLTAGE SWING (V)
REFERRED TO SUPPLY VOLTAGES
AD8475
AD8475
0
–1.94
G = 0.8
0
–1.94
G = 0.4
–20
GAIN (dB)
GAIN (dB)
–7.96
–10
–30
G = 0.8
–7.96
–10
G = 0.4
–20
10k
100k
1M
10M
100M
1G
FREQUENCY (Hz)
–30
1k
09432-017
–50
1k
100k
1M
10M
100M
FREQUENCY (Hz)
Figure 20. Large Signal Frequency Response for All Gains, VS = ±5 V
Figure 17. Small Signal Frequency Response for All Gains VS = ±5 V
0
10k
09432-019
–40
0
VS = ±5V
VS = +3V
VS = +5V
–7.96
–10
VS = ±5V
VS = +3V
VS = +5V
–7.96
GAIN (dB)
GAIN (dB)
–10
–20
–20
100k
1M
10M
100M
FREQUENCY (Hz)
–30
1k
–10
–10
–20
–20
GAIN (dB)
0
–30
–40
10M
100M
–30
–40
RL = 200Ω
RL = 1kΩ
RL = 10kΩ
10M
100M
FREQUENCY (Hz)
09432-022
GAIN (dB)
1M
Figure 21. Large Signal Frequency Response for Various Supplies
0
1M
100k
FREQUENCY (Hz)
Figure 18. Small Signal Frequency Response for Various Supplies
–50
100k
10k
Figure 19. Small Signal Frequency Response for Various Loads
–50
100k
RL = 200Ω
RL = 1kΩ
RL = 10kΩ
1M
10M
100M
FREQUENCY (Hz)
Figure 22. Large Signal Frequency Response for Various Loads
Rev. B | Page 10 of 24
09432-024
10k
09432-018
–40
1k
09432-020
–30
AD8475
0
0
CL = 0pF
CL = 5pF
CL = 10pF
–7.96
–10
CL = 0pF
CL = 5pF
CL = 10pF
–7.96
GAIN (dB)
GAIN (dB)
–10
–20
–20
10k
100k
1M
10M
100M
FREQUENCY (Hz)
Figure 23. Small Signal Frequency Response for Various Capacitive Loads
0
–30
1k
09432-025
–40
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
09432-027
–30
Figure 26. Large Signal Frequency Response for Various Capacitive Loads
0
VOCM = 1V
VOCM = 2.5V
VOCM = 4V
VOCM = 1.5V
VOCM = 2.5V
VOCM = 3.5V
–10
GAIN (dB)
GAIN (dB)
–10
–20
–20
100k
1M
10M
100M
FREQUENCY (Hz)
Figure 24. Small Signal Frequency Response for Various VOCM Levels
100k
1M
10M
100M
FREQUENCY (Hz)
Figure 27. Large Signal Frequency Response for Various VOCM Levels
10
VOUT = 100mV p-p
VOCM = 2.5V
VOUT = 2V p-p
VOCM = 2.5V
0
VOCM GAIN (dB)
0
–5
–10
–10
–20
–30
–15
–2
1k
10k
100k
1M
10M
FREQUENCY (Hz)
09432-056
VOCM GAIN (dB)
10k
–40
1k
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 28. VOCM Large Signal Frequency Response
Figure 25. VOCM Small Signal Frequency Response
Rev. B | Page 11 of 24
09432-055
5
–30
1k
09432-026
–40
10k
09432-028
–30
AD8475
VOUT = 2V p-p
20ns/DIV
Figure 29. Small Signal Pulse Response, VS = ±2.5 V
09432-033
10ns/DIV
09432-029
20mV/DIV
500mV/DIV
VOUT = 100mV p-p
Figure 32. Large Signal Pulse Response, VS = ±2.5 V
CL = 0pF
CL = 5pF
CL = 10pF
20ns/DIV
Figure 30. Small Signal Step Response for Various Capacitive Loads,
VS = ±2.5 V
09432-035
10ns/DIV
09432-031
20mV/DIV
500mV/DIV
CL = 0pF
CL = 5pF
CL = 10pF
Figure 33. Large Signal Step Response for Various Capacitive Loads
RL = 200Ω
RL = 1kΩ
RL = 10kΩ
20ns/DIV
Figure 31. Small Signal Step Response for Various Resistive Loads
09432-034
10ns/DIV
09432-030
20mV/DIV
500mV/DIV
RL = 200Ω
RL = 1kΩ
RL = 10kΩ
Figure 34. Large Signal Step Response for Various Resistive Loads
Rev. B | Page 12 of 24
500ns/DIV
Figure 35. VOCM Small Signal Step Response, VS = ±2.5 V
–20
= 0.4
= 0.4
= 0.8
= 0.8
–60
–80
–100
–120
10
–80
–100
–140
0.1
09432-043
1
FREQUENCY (MHz)
1
10
FREQUENCY (MHz)
Figure 36. Harmonic Distortion vs. Frequency at Various Gains
Figure 39. Harmonic Distortion vs. Frequency at Various Supplies
–20
–20
VOUT = 2V p-p
HD2, RL = 1kΩ
HD3, RL = 1kΩ
–40
HD2, RL = 200Ω
HD3, RL = 200Ω
HARMONIC DISTORTION (dBc)
–40
–60
–80
–100
–120
HD2,
HD3,
HD2,
HD3,
VOUT = 2V p-p
VOUT = 2V p-p
VOUT = 4V p-p
VOUT = 4V p-p
–60
–80
–100
–120
1
10
FREQUENCY (MHz)
09432-040
HARMONIC DISTORTION (dBc)
–60
–120
–140
0.1
–140
0.1
VOUT = 2V p-p
HD2, VS = +5V
HD3, VS = +5V
–40
HD2, VS = ±5V
HD3, VS = ±5V
09432-042
G
G
G
G
Figure 37. Harmonic Distortion vs. Frequency at Various Loads
–140
0.1
1
10
FREQUENCY (MHz)
Figure 40. Harmonic Distortion vs. Frequency at Various VOUT,dm
Rev. B | Page 13 of 24
09432-046
HARMONIC DISTORTION (dBc)
–40
HD2,
HD3,
HD2,
HD3,
Figure 38. VOCM Large Signal Step Response
HARMONIC DISTORTION (dBc)
–20
09432-036
50ns/DIV
09432-032
20mV/DIV
500mV/DIV
AD8475
AD8475
–20
SPURIOUS-FREE DYANMIC RANGE (dBc)
HARMONIC DISTORTION (dBc)
f = 100kHz
HD2, +5V SUPPLY
HD3, +5V SUPPLY
–40
HD2, ±5V SUPPLY
HD3, ±5V SUPPLY
–60
–80
–100
–140
0
1
2
3
4
5
6
7
8
9
VOUT (V p-p)
–60
–80
–100
–120
–140
0.1
09432-047
–120
VOUT = 2V p-p
RL = 1kΩ
RL = 200Ω
–40
1
10
FREQUENCY (MHz)
09432-049
–20
Figure 44. Spurious-Free Dynamic Range vs. Frequency at Various Loads
Figure 41. Harmonic Distortion vs. VOUT at Various Supplies
100
10
0
NORMALIZED SPECTRUM (dBc)
–10
OUTPUT IMPEDANCE (Ω)
–20
–30
–40
–50
–60
–70
–80
10
1
0.1
–90
80
85
90
95
100
105
110
115
120
125
FREQUENCY (kHz)
0.01
10k
100k
1M
10M
100M
FREQUENCY (Hz)
Figure 45. Output Impedance vs. Frequency
Figure 42. 100 kHz Intermodulation Distortion
100
90
70
500nV/DIV
60
50
40
30
20
0
1
10
100
1k
10k
FREQUENCY (Hz)
100k
1s/DIV
Figure 43. Voltage Noise Density vs. Frequency
Figure 46. 0.1 Hz to 10 Hz Voltage Noise
Rev. B | Page 14 of 24
09432-039
10
09432-243
VOLTAGE NOISE (nV/ Hz)
80
09432-052
–110
75
09432-054
–100
AD8475
–30
–50
–60
–70
–80
–90
–100
1M
10M
FREQUENCY (Hz)
100M
09432-050
OUTPUT BALANCE ERROR (dB)
–40
Figure 47. Output Balance Error vs. Frequency
Rev. B | Page 15 of 24
AD8475
TERMINOLOGY
Common-Mode Voltage
Common-mode voltage refers to the average of two node voltages
with respect to the local ground reference. The output commonmode voltage is defined as
1kΩ
1.25kΩ
RL, dm VOUT, dm
AD8475
VOCM
–IN
–OUT
1.25kΩ
VOUT, cm = (V+OUT + V−OUT)/2
+OUT
1kΩ
09432-162
+IN
Figure 48. Signal and Circuit Definitions
Differential Voltage
Differential voltage refers to the difference between two
node voltages. For example, the output differential voltage (or
equivalently, output differential mode voltage) is defined as
VOUT, dm = (V+OUT − V−OUT)
where V+OUT and V−OUT refer to the voltages at the +OUT and
−OUT terminals with respect to a common ground reference.
Similarly, the differential input voltage is defined as
Balance
Output balance is a measure of how close the output differential
signals are to being equal in amplitude and opposite in phase.
Output balance is most easily determined by placing a wellmatched resistor divider between the differential voltage nodes
and comparing the magnitude of the signal at the divider midpoint
with the magnitude of the differential signal. By this definition,
output balance is the magnitude of the output common-mode
voltage divided by the magnitude of the output differential
mode voltage.
VIN, dm = (V+IN − (V−IN))
Rev. B | Page 16 of 24
Output Balance Error =
ΔVOUT , cm
ΔVOUT , dm
AD8475
THEORY OF OPERATION
OVERVIEW
DC PRECISION
The AD8475 is a fully differential amplifier, with integrated lasertrimmed resistors, that provides precision attenuating gains of
0.4 and 0.8. The internal differential amplifier of the AD8475
differs from conventional operational amplifiers in that it has
two outputs whose voltages are equal in magnitude, but move in
opposite directions (180° out of phase). An additional input,
VOCM, sets the output common-mode voltage. Like an operational amplifier, it relies on high open-loop gain and negative
feedback to force the output nodes to the desired voltages. The
AD8475 is designed to greatly simplify single-ended-to-differential
conversion, common-mode level shifting and precision attenuation of large signals so that they are compatible with low voltage,
differential input ADCs.
The dc precision of the AD8475 is highly dependent on the
accuracy of its internal resistors. Using superposition to analyze
the circuit shown in Figure 50, the following equation shows the
relationship between the input and output voltages of the
amplifier:
1.25kΩ
–VS
NC
where,
RP =
1kΩ
1
VIN ,cm = (VP + VN )
2
1.25kΩ
–IN 0.8x –IN 0.4x
+VS
The differential closed loop gain of the amplifier is
1kΩ
VOCM
VOUT ,dm
+OUT
VIN ,dm
09432-062
1.25kΩ
RFP
RFN
, RN =
RGP
RGN
VIN ,dm = VP − VN
–OUT
AD8475
1.25kΩ
1
(2RP RN + RP + RN )
2
1
= VOUT ,cm (RP − RN ) + VOUT ,dm (2 + RP + RN )
2
=
2RP RN + RP + RN
2 + RP + RN
and the common rejection of the amplifier is
Figure 49. Block Diagram
VOUT ,dm
CIRCUIT INFORMATION
VIN ,cm
The AD8475 amplifier uses a voltage feedback topology;
therefore, the amplifier exhibits a nominally constant gain
bandwidth product. Like a voltage feedback operational
amplifier, the AD8475 also has high input impedance at its
internal input terminals (the summing nodes of the internal
amplifier) and low output impedance.
=
2(RP − RN )
2 + RP + R N
VP
RGP
RFP
VON
VOCM
VOP
VN
The AD8475 employs two feedback loops, one each to control
the differential and common-mode output voltages. The differential feedback loop, which is fixed with precision laser trimmed
on-chip resistors, controls the differential output voltage.
Output Common-Mode Voltage (VOCM)
The internal common-mode feedback controls the commonmode output voltage. This architecture makes it easy to set the
output common-mode level to any arbitrary value independent
of the input voltage. The output common-mode voltage is
forced by the internal common-mode feedback loop to be equal
to the voltage applied to the VOCM input. The VOCM pin can
be left unconnected, and the output common-mode voltage
self-biases to midsupply by the internal feedback control.
Due to the internal common-mode feedback loop and the fully
differential topology of the amplifier, the AD8475 outputs are
precisely balanced over a wide frequency range. This means that
the amplifier’s differential outputs are very close to the ideal of
being identical in amplitude and exactly 180° out of phase.
RGN
RFN
09432-163
+IN 0.8x +IN 0.4x
VIN ,cm (RP − RN ) + VIN ,dm
Figure 50. Functional Circuit Diagram of the AD8475 at a Given Gain
The preceding equations show that the gain accuracy and the
common-mode rejection (CMRR) of the AD8475 are determined primarily by the matching of the feedback networks
(resistor ratios). If the two networks are perfectly matched, that
is, if RP and RN equal RF/RG, then the resistor network does not
generate any CMRR errors and the differential closed loop gain
of the amplifier reduces to
v OUT ,dm
v IN ,dm
=
RF
RG
The AD8475’s integrated resistors are precision wafer-lasertrimmed to guarantee a minimum CMRR of 86dB (50μV/V),
and gain error of less that 0.05%. To achieve equivalent precision
and performance using a discrete solution, resistors must be
matched to 0.01% or better.
Rev. B | Page 17 of 24
AD8475
INPUT VOLTAGE RANGE
DRIVING THE AD8475
The AD8475 can measure input voltages that are larger than the
supply rails. The internal gain and feedback resistors form a
divider, which reduces the input voltage seen by the internal
input nodes of the amplifier. The largest voltage that can be
measured is constrained by the capability of the amplifier’s
internal summing nodes. This voltage is defined by the input
voltage and the ratio between the feedback and the gain resistors.
Figure 51 shows the voltage at the internal summing nodes of
the amplifier, defined by the input voltage and internal resistor
network. If VN is grounded, the expression shown in the figure
reduces to
Care should be taken to drive the AD8475 with a low
impedance source: for example, another amplifier. Source
resistance can unbalance the resistor ratios and, therefore,
significantly degrade the gain accuracy and common-mode
rejection of the AD8475. For the best performance, source
impedance to the AD8475 input terminals should be kept
below 0.1 Ω. Refer to the DC Precision section for details on
the critical role of resistor ratios in the precision of the AD8475.
VPLUS = V MINUS =
POWER SUPPLIES
The AD8475 operates over a wide range of supply voltages. It
can be powered on a single supply as low as 3 V and as high as
10 V. The AD8475 can also operate on dual supplies from
±1.5 V up to ±5 V
RG ⎛
1 RF
VP ⎞⎟
⎜ VOCM +
RF + RG ⎝
2 RG
⎠
The internal amplifier of the AD8475 has rail-to-rail inputs. To
obtain accurate measurements with minimal distortion, the
voltage at the internal inputs of the amplifier must stay below
+VS − 1 V and above −VS.
A stable dc voltage should be used to power the AD8475. Note
that noise on the supply pins can adversely affect performance.
For more information, see the PSRR performance curve in
Figure 13.
For example, with VS = 5 V in a G = 0.4 configuration, the
AD8475 can measure an input as high as ±12.5 V and maintain
its excellent distortion performance.
Place a bypass capacitor of 0.1 μF between each supply pin and
ground, as close as possible to each supply pin. Use a tantalum
capacitor of 10 μF between each supply and ground. It can be
farther away from the supply pins and, typically, it can be
shared by other precision integrated circuits.
VP
RG
RF + RG
VOCM +
1 RF
2 RG
VP − VN
+
RF
RF + RG
RG
RF
VON
VN
VOCM
VOP
VN
RG
RF
Figure 51. Voltages at the Internal Op Amp Inputs of the AD8475
Rev. B | Page 18 of 24
09432-164
The AD8475 provides overvoltage protection for excessive input
voltages beyond the supply rails. Integrated ESD protection diodes
at the inputs prevent damage to the AD8475 up to +VS + 10.5 V
and −VS − 16 V.
AD8475
APPLICATIONS INFORMATION
TYPICAL CONFIGURATION
SETTING THE OUTPUT COMMON-MODE VOLTAGE
The AD8475 is designed to facilitate single-ended-to-differential
conversion, common-mode level shifting, and precision attenuation
of large signals so that they are compatible with low voltage ADCs.
The VOCM pin of the AD8475 is internally biased with a
precision voltage divider comprising two 200 kΩ resistors between
the supplies. This divider level shifts the output to midsupply.
Relying on the internal bias results in an output common-mode
voltage that is within 0.01% of the expected value.
Figure 53 shows a typical connection diagram of the AD8475
in a gain of 0.4. To use the AD8475 in a gain of 0.8, drive the
±IN 0.8x inputs with a low impedance source.
In cases where control of the output common-mode level is
desired, an external source or resistor divider with source
resistance less than 100 Ω can be used to drive the VOCM pin.
If an external voltage divider consisting of equal resistor values
is used to set VOCM to midsupply, higher values can be used
because the external resistors are placed in parallel with the
internal resistors. The output common-mode offset listed in the
Specifications section assumes that the VOCM input is driven by a
low impedance voltage source.
SINGLE-ENDED TO DIFFERENTIAL CONVERSION
Many industrial systems use single-ended; however, the signals
are frequently processed by high performance differential input
ADCs for higher precision. The AD8475 performs the critical
function of precisely converting single-ended signals to the
differential inputs of precision ADCs, and it does so with no
need for external components.
To convert a single-ended signal to a differential signal, connect
one input to the signal source and the other input to ground (see
Figure 55). Note that either input can be driven by the source
with the only effect being that the outputs have reversed polarity.
The AD8475 also accepts truly differential input signals in
precision systems with differential signal paths.
Because of the internal divider, the VOCM pin sources and sinks
current, depending on the externally applied voltage and its
associated source resistance.
It is also possible to connect the VOCM input to the commonmode level output of an ADC; however, care must be taken to
ensure that the output has sufficient drive capability. The input
impedance of the VOCM pin is 100 kΩ. If multiple AD8475
devices share one ADC reference output, a buffer may be necessary to drive the parallel inputs.
–VS
+ 10µF
0.1µF
LOW
IMPEDANCE
INPUT SOURCE
1.25kΩ
–VS
NC
–OUT
1kΩ
1.25kΩ
VOUT = (V+OUT – V–OUT)
AD8475
1.25kΩ
–IN 0.8x
–IN 0.4x
10µF
+
1.25kΩ
+VS
1kΩ
VOCM
+OUT
REF
0.1µF
0.1µF
+VS
Figure 52. Typical Configuration—10-Lead MSOP
Rev. B | Page 19 of 24
09432-200
+IN 0.8x +IN 0.4x
AD8475
–VS
VIN
14 –VS
15 –VS
16 +IN 0.4x
LOW
IMPEDANCE
INPUT SOURCE
13 –VS
+ 10µF
0.1µF
12 NC
+IN 0.4x 1
1kΩ
+IN 0.8x 2
1.25kΩ
1.25kΩ
–IN 0.8x 3
–IN 0.4x 4
1.25kΩ
11 –OUT
AD8475
10 +OUT
VOUT = (V+OUT – V–OUT)
1kΩ
1.25kΩ
9
VOCM
REF
+
+VS 8
+VS 7
0.1µF
09432-165
10µF
+VS 6
–IN 0.4x 5
0.1µF
+VS
Figure 53. Typical Configuration—16-Lead LFCSP
HIGH PERFORMANCE ADC DRIVING
The AD8475 is ideally suited for broadband dc-coupled and
industrial applications. The circuit in Figure 55 shows an
industrial front-end connection for an AD8475 driving an
AD7982, a 18-bit, 1 MSPS ADC, with dc coupling on the
AD8475 input and output. (The AD7982 achieves its optimum
performance when driven differentially.) The AD8475 performs
the attenuation of a 20 V p-p input signal, level shifts it, and
converts it to a differential signal without the need for any
external components. The AD8475 eliminates the need for dual
supplies at the front end to accept large bipolar signals. It also
eliminates the need for a precision resistor network for attenuation, and a transformer to drive the ADC and perform the singleended-to-differential conversion.
The ac and dc performance of the AD8475 are compatible with
the 18-bit, 1 MSPS AD7982 PulSAR® ADC and other 16-bit and
18-bit members of the family, which have sampling rates up to
4 MSPS. Some suitable high performance differential ADCs are
listed in Table 6.
Table 6. High Performance SAR ADCs
Part
Resolution
AD7984 18 Bits
Sample
Rate
1.33 MSPS
AD7982
18 Bits
1 MSPS
AD7690
18 Bits
400 kSPS
AD7641
18 Bits
2 MSPS
Description
True differential input,
14 mW, 2.5 V ADC
True differential Input,
7.0 mW, 2.5 V ADC
True differential input,
4.5 mW, 5 V ADC
True differential input,
75 mW, 2.5 V ADC
In this example, the AD8475 is powered with a single 5 V
supply and used in a gain of 0.4, with a single-ended input
converted to a differential output. The input is a 20 V p-p
symmetric, ground-referenced bipolar signal. With an output
common-mode voltage of 2.5 V, each AD8475 output swings
between 0.5 V and 4.5 V, opposite in phase, providing an 8 V p-p
differential signal to the ADC input.
Rev. B | Page 20 of 24
AD8475
The differential RC network between the AD8475 output and the
ADC provides a single-pole filter that reduces undesirable
aliasing effects and high frequency noise. The common-mode
bandwidth of the filter is 29.5 MHz (20 Ω, 270 pF), and the
differential bandwidth is 3.1 MHz (40 Ω, 1.3 nF).
09432-168
The VOCM input is bypassed for noise reduction, and set
externally with 1% resistors to maximize output dynamic
range on a single 5 V supply.
Figure 54. FFT Results of the AD8475 Driving the AD7982
+4.5V
+5V
4V
+2.5V
+10V
+2.5V
VDD
+IN 0.4x
20V
NC
–OUT
+IN 0.8x
20Ω
NC
–IN 0.8x
–IN 0.4x
+OUT
20Ω
SCK
AD7982
1.3nF
SDO
270pF
IN+
VOCM
CNV
REF
–VS
+4.5V
+7V TO +18V
4V
ADR435
SDI
270pF
AD8475
–10V
VIO
IN–
GND
+5V
2.5V
10kΩ
+5V
+0.5V
0.1µF
10kΩ
Figure 55. Attenuation and Level Shifting of Industrial Voltages to Drive Single-Supply Precision ADC
Rev. B | Page 21 of 24
09432-167
0V
+1.8V TO +5V
+0.5V
+VS
AD8475
AD8475 EVALUATION BOARD
An evaluation board for the AD8475 is available to facilitate
standalone testing of the AD8475 performance and functionality
for customer evaluation and system design. The board provides
the user flexibility to configure the AD8475 in the desired gain
(0.4 or 0.8) and to install the suitable input and load impedances.
The AD8475-EVALZ board is designed so that a user can easily
evaluate system performance when the AD8475 is mated with
any Analog Devices, Inc., SAR ADC. The board can be installed
with SMB connectors that mate directly to the Pulsar® Analogto-Digital Converter Evaluation Kit.
See the AD8475 product page for more information on the
AD8475-EVALZ.
+VS
(GRN)
C4
10µF
J1
R6
R3
0Ω
–IN 0.8x 3
R4
0Ω
13 –VS
14 –VS
1kΩ
+IN 0.8x 2
IN–
12 NC
+IN 0.4x 1
R1
0Ω
–IN 0.4x 4
1.25kΩ
1.25kΩ
AD8475
1.25kΩ
11 –OUT
R7
10 +OUT
R8
1kΩ
1.25kΩ
9
VOCM
OUT–
R9
R12
J4
VOCM
+VS 8
+VS 7
+VS 6
J5
VOCM
R11
J3
C1
0.1µF
+
–IN 0.4x 5
OUT+
R10
J2
C5
0.1µF
JP1
C3
10µF
+VS
(RED)
Figure 56. AD8475-EVALZ Schematic
Rev. B | Page 22 of 24
09432-065
R5
15 –VS
16 +IN 0.4x
+
R2
0Ω
IN+
C2
0.1µF
AD8475
OUTLINE DIMENSIONS
3.10
3.00 SQ
2.90
PIN 1
INDICATOR
0.30
0.25
0.20
13
0.50
BSC
PIN 1
INDICATOR
16
1
12
1.65
1.50 SQ
1.45
EXPOSED
PAD
9
0.80
0.75
0.70
BOTTOM VIEW
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
0.20 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
091609-A
TOP VIEW
4
5
8
0.50
0.40
0.30
COMPLIANT TO JEDEC STANDARDS MO-229.
Figure 57. 16-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
3 mm × 3 mm Body, Very Very Thin Quad
(CP-16-27)
Dimensions shown in millimeters
3.10
3.00
2.90
3.10
3.00
2.90
10
1
5.15
4.90
4.65
6
5
PIN 1
IDENTIFIER
0.50 BSC
0.95
0.85
0.75
15° MAX
1.10 MAX
0.30
0.15
6°
0°
0.23
0.13
COMPLIANT TO JEDEC STANDARDS MO-187-BA
Figure 58. 10-Lead Mini Small Outline Package [MSOP]
(RM-10)
Dimensions shown in millimeters
Rev. B | Page 23 of 24
0.70
0.55
0.40
091709-A
0.15
0.05
COPLANARITY
0.10
AD8475
ORDERING GUIDE
Model 1
AD8475ACPZ-R7
AD8475ACPZ-RL
AD8475ACPZ-WP
AD8475BRMZ
AD8475BRMZ-R7
AD8475BRMZ-RL
AD8475ARMZ
AD8475ARMZ-R7
AD8475ARMZ-RL
AD8475-EVALZ
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
16-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
16-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
16-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
10-Lead Lead Frame Chip Scale Package [MSOP]
10-Lead Lead Frame Chip Scale Package [MSOP]
10-Lead Lead Frame Chip Scale Package [MSOP]
10-Lead Lead Frame Chip Scale Package [MSOP]
10-Lead Lead Frame Chip Scale Package [MSOP]
10-Lead Lead Frame Chip Scale Package [MSOP]
Evaluation Board
Z = RoHS Compliant Part.
©2010–2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09432-0-4/11(B)
Rev. B | Page 24 of 24
Package Option
CP-16-27
CP-16-27
CP-16-27
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
Branding
Y3H
Y3H
Y3H
Y41
Y41
Y41
Y31
Y31
Y31