INTEGRATED CIRCUITS DATA SHEET TDA1015T 0,5 W audio power amplifier Product specification File under Integrated Circuits, ICO1 March 1986 Philips Semiconductors Product specification 0,5 W audio power amplifier TDA1015T GENERAL DESCRIPTION The TDA1015T is a low-cost audio amplifier which can deliver up to 0,5 W output power into a 16 Ω load impedance at a supply voltage of 9 V. The amplifier is specially designed for portable applications such as radios and recorders. The IC has a very low supply voltage requirement (3,6 V min.). Features • High input impedance • Separated preamplifier and power amplifier • Limited noise behaviour at radio frequencies • Short-circuit protected • Miniature encapsulation. QUICK REFERENCE DATA Supply voltage range VP Peak output current IOM max. 1A Output power Po typ. 0,5 W Voltage gain power amplifier GV1 typ. 29 dB Voltage gain preamplifier GV2 typ. 23 dB Total quiescent current Itot max. 22 mA Operating ambient temperature range Tamb −25 to +150 °C Storage temperature range Tstg −55 to + 150 °C PACKAGE OUTLINE 8-lead mini-pack; plastic (SO8; SOT96A); SOT96-1; 1996 July 23. March 1986 2 3,6 to 12 V Philips Semiconductors Product specification 0,5 W audio power amplifier TDA1015T Fig.1 Block diagram. RATINGS Limiting values in accordance with the Absolute Maximum System (IEC 134) Supply voltage VP max. 12 V Peak output current IOM max. 1A Total power dissipation see derating curve Fig.2 −55 to + 150 °C Storage temperature range A.C. short-circuit duration of load during sine-wave drive at VP = 9 V Fig.2 Power derating curve. March 1986 3 tsc max. 1 hour Philips Semiconductors Product specification 0,5 W audio power amplifier TDA1015T CHARACTERISTICS Tamb = 25 °C; VP = 9 V; RL = 16 Ω; f = 1 kHz; see Fig.3; unless otherwise specified SYMBOL VP IORM Itot PARAMETER MIN. TYP. MAX. UNIT Supply voltage 3,6 9 12 V Repetitive peak output current − − 1 A Total quiescent current − 12 22 mA − 0,5 − W A.F. output power at dtot = 10%; note 1 Po VP = 9 V; RL = 16 Ω − 0,3 − W Gv1 Voltage gain power amplifier − 29 − dB Gv2 Voltage gain preamplifier (note 2) − 23 − dB Gtot Total voltage gain 49 52 55 Frequency response at −3 dB (note 3) − 60 to 15 000 − Hz Input impedance power amplifier − 20 − kΩ Po B |Zi1| VP = 6 V; RL = 8 Ω dB |Zi2| Input impedance preamplifier (note 4) 100 200 − kΩ |Zo2| Output impedance preamplifier 0,5 1 1,5 kΩ − 0,7 − V RS = 0 Ω − 0,2 − mV RS = 10 kΩ − 0,5 − mV − 8 − µV − 38 − dB Output voltage preamplifier (r.m.s. value) Vo2(rms) dtot < 1% (note 2) Noise output voltage (r.m.s. value); note 5 Vn(rms) Vn(rms) Noise output voltage (r.m.s. value) Vn(rms) f = 500 kHz; B = 5 kHz; RS = 0 Ω Ripple rejection at f = 100 Hz; RR C2 = 1 µF (note 6) Notes to the characteristics 1. Output power is measured with an ideal coupling capacitor to the speaker load. 2. Measured with a load resistance of 20 kΩ. 3. The frequency response is mainly determined by the capacitors, C1, C3 (low frequency) and C4 (high frequency). 4. Independent of load impedance of preamplifier. 5. Effective unweighted r.m.s. noise voltage measured in a bandwidth from 60 Hz to 15 kHz (slopes 12 dB/octave). 6. Ripple rejection measured with a source impedance between 0 and 2 kΩ (maximum ripple amplitude of 2 V). March 1986 4 Philips Semiconductors Product specification 0,5 W audio power amplifier TDA1015T APPLICATION INFORMATION Fig.3 Test circuit. ______ measured in Fig.3 − − − − measured with a 1,5 MΩ resistor connected between pins 7 and 2. Fig.4 March 1986 Total quiescent current as a function of supply voltage. Fig.5 5 Output power as a function of supply voltage; dtot = 10%; f = 1 kHz. Philips Semiconductors Product specification 0,5 W audio power amplifier TDA1015T ______ measured in Fig.3 − − − − measured with a 1,5 MΩ resistor connected between pins 7 and 2. Fig.6 Total distortion as a function of output power; VP = 9 V; RL = 16 Ω; f = kHz. Fig.7 Application circuit for power stage only and battery power supply; Gv1 = 29 dB; |Zi1| = 20 kΩ. March 1986 6 Philips Semiconductors Product specification 0,5 W audio power amplifier Fig.8 March 1986 TDA1015T Application circuit for preamplifier and power amplifier stages and battery power supply; Gv tot = 52 dB; |Zi2| = 200 kΩ. 7 Philips Semiconductors Product specification 0,5 W audio power amplifier TDA1015T PACKAGE OUTLINE SO8: plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 D E A X c y HE v M A Z 5 8 Q A2 A (A 3) A1 pin 1 index θ Lp 1 L 4 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) mm 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 5.0 4.8 4.0 3.8 1.27 6.2 5.8 1.05 1.0 0.4 0.7 0.6 0.25 0.25 0.1 0.7 0.3 0.01 0.019 0.0100 0.014 0.0075 0.20 0.19 0.16 0.15 0.244 0.039 0.028 0.050 0.041 0.228 0.016 0.024 inches 0.010 0.057 0.069 0.004 0.049 0.01 0.01 0.028 0.004 0.012 θ Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT96-1 076E03S MS-012AA March 1986 EIAJ EUROPEAN PROJECTION ISSUE DATE 95-02-04 97-05-22 8 o 8 0o Philips Semiconductors Product specification 0,5 W audio power amplifier TDA1015T During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. Maximum permissible solder temperature is 260 °C, and maximum duration of package immersion in solder is 10 seconds, if cooled to less than 150 °C within 6 seconds. Typical dwell time is 4 seconds at 250 °C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “IC Package Databook” (order code 9398 652 90011). Repairing soldered joints Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 °C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 °C. Reflow soldering Reflow soldering techniques are suitable for all SO packages. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Several techniques exist for reflowing; for example, thermal conduction by heated belt. Dwell times vary between 50 and 300 seconds depending on heating method. Typical reflow temperatures range from 215 to 250 °C. Preheating is necessary to dry the paste and evaporate the binding agent. Preheating duration: 45 minutes at 45 °C. Wave soldering Wave soldering techniques can be used for all SO packages if the following conditions are observed: • A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering technique should be used. • The longitudinal axis of the package footprint must be parallel to the solder flow. • The package footprint must incorporate solder thieves at the downstream end. March 1986 9 Philips Semiconductors Product specification 0,5 W audio power amplifier TDA1015T DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. March 1986 10