AD ADCMP567BCP

Dual Ultrafast
Voltage Comparator
ADCMP567
FEATURES
250 ps propagation delay input to output
50 ps propagation delay dispersion
Differential PECL compatible outputs
Differential latch control
Robust input protection
Input common-mode range −2.0 V to +3.0 V
Input differential range ±5 V
ESD protection >3 kV HBM, >200 V MM
Power supply sensitivity >65 dB
200 ps minimum pulsewidth
5 GHz equivalent input rise time bandwidth
Typical output rise/fall of 165 ps
APPLICATIONS
High speed instrumentation
Scope and logic analyzer front ends
Window comparators
High speed line receivers and signal restoration
Threshold detection
Peak detection
High speed triggers
Patient diagnostics
Disk drive read channel detection
Hand-held test instruments
Zero-crossing detectors
Clock drivers
Automatic test equipment
FUNCTIONAL BLOCK DIAGRAM
NONINVERTING
INPUT
Q OUTPUT
ADCMP567
INVERTING
INPUT
Q OUTPUT
LATCH ENABLE
INPUT
LATCH ENABLE
INPUT
03632-0-001
Figure 1.
GENERAL DESCRIPTION
The ADCMP567 is an ultrafast voltage comparator fabricated
on Analog Devices’ proprietary XFCB process. The device
features 250 ps propagation delay with less than 35 ps overdrive
dispersion. Overdrive dispersion, a particularly important
characteristic of high speed comparators, is a measure of the
difference in propagation delay under differing overdrive
conditions.
A fast, high precision differential input stage permits consistent propagation delay with a wide variety of signals in the
common-mode range from −2.0 V to +3.0 V. Outputs are
complementary digital signals fully compatible with PECL 10 K
and 10 KH logic families. The outputs provide sufficient drive
current to directly drive transmission lines terminated in 50 Ω
to VDD − 2 V. A latch input is included, which permits tracking,
track-and-hold, or sample-and-hold modes of operation.
The ADCMP567 is available in a 32-lead LFCSP package.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703
© 2003 Analog Devices, Inc. All rights reserved.
ADCMP567
TABLE OF CONTENTS
Specifications..................................................................................... 3
Optimizing High Speed Performance ........................................9
Absolute Maximum Ratings............................................................ 5
Comparator Propagation Delay Dispersion ..............................9
Thermal Considerations.............................................................. 5
Comparator Hysteresis .............................................................. 10
ESD Caution.................................................................................. 5
Minimum Input Slew Rate Requirement ................................ 10
Pin Configuration and Function Descriptions............................. 6
Typical Application Circuits ..................................................... 11
Timing Information ......................................................................... 8
Typical Performance Characteristics ........................................... 12
Application Information.................................................................. 9
Outline Dimensions ....................................................................... 14
Clock Timing Recovery ............................................................... 9
Ordering Guide .......................................................................... 14
REVISION HISTORY
Revision 0: Initial Version
Rev. 0 | Page 2 of 16
ADCMP567
SPECIFICATIONS
Table 1. ADCMP567 ELECTRICAL CHARACTERISTICS (VCC = +5.0 V, VEE = −5.2 V, VDD = +3.3 V, TA = 25°C, unless otherwise noted.)
Parameter
DC INPUT CHARACTERISTICS (See Note)
Input Common-Mode Range
Input Differential Voltage
Input Offset Voltage
Input Offset Voltage Channel Matching
Offset Voltage Tempco
Input Bias Current
Input Bias Current Tempco
Input Offset Current
Input Capacitance
Input Resistance, Differential Mode
Input Resistance, Common Mode
Open Loop Gain
Common-Mode Rejection Ratio
Hysteresis
LATCH ENABLE CHARACTERISTICS
Latch Enable Common-Mode Range
Latch Enable Differential Input Voltage
Input High Current
Input Low Current
Latch Setup Time
Latch to Output Delay
Latch Pulsewidth
Latch Hold Time
OUTPUT CHARACTERISTICS
Output Voltage—High Level
Output Voltage—Low Level
Rise Time
Fall Time
AC PERFORMANCE
Propagation Delay
Propagation Delay
Propagation Delay Tempco
Prop Delay Skew—Rising Transition to
Falling Transition
Within Device Propagation Delay Skew—
Channel to Channel
Propagation Delay Dispersion vs.
Duty Cycle
Propagation Delay Dispersion vs.
Overdrive
Propagation Delay Dispersion vs.
Overdrive
Propagation Delay Dispersion vs.
Slew Rate
Propagation Delay Dispersion vs.
Common-Mode Voltage
Symbol
Condition
VCM
Min
VOS
−2.0
−5
−5.0
DVOS/dT
IBC
−10
−8.0
CIN
CMRR
VCM = −2.0 V to +3.0 V
VLCM
VLD
±1.0
±1.0
10.0
+24
10.0
±0.5
0.75
100
600
60
69
±1.0
Max
Unit
+3.0
+5
+5.0
V
V
mV
mV
µV/°C
µA
nA/°C
µA
pF
kΩ
kΩ
dB
dB
mV
+42
+8.0
VDD
2.0
+12
+12
V
V
µA
µA
ps
ps
ps
ps
VDD − 0.81
VDD − 1.54
175
140
V
V
ps
ps
250
300
0.5
±10
ps
ps
ps/°C
ps
±10
ps
±10
ps
50 mV to 1.5 V
35
ps
20 mV to 1.5 V
50
ps
0 V to 1 V swing,
20% to 80%,
50 ps and 600 ps
1 V swing,
−1.5 V to 2.5 VCM
50
ps
5
ps
tS
tPLOH, tPLOL
tPL
tH
@ 0.0 V
@ −2.0 V
250 mV overdrive
250 mV overdrive
250 mV overdrive
250 mV overdrive
VOH
VOL
tR
tF
PECL 50 Ω to −2.0 V
PECL 50 Ω to −2.0 V
20% to 80%
20% to 80%
tPD
tPD
1 V overdrive
20 mV overdrive
Rev. 0 | Page 3 of 16
VDD − 2.0
0.4
−12
−12
Typ
+6
+6
50
300
150
90
VDD − 1.1
VDD − 1.95
ADCMP567
Parameter
AC PERFORMANCE (continued)
Equivalent Input Rise Time Bandwidth
Toggle Rate
Minimum Pulsewidth
Unit to Unit Propagation Delay Skew
POWER SUPPLY
Positive Supply Current
Symbol
Condition
Min
Typ
BW
0 V to 1 V swing,
20% to 80%,
50 ps tR, tF
>50% output swing
∆tPD from 10 ns to
200 ps < ±25 ps
3500
5000
MHz
5
200
Gbps
ps
±10
ps
PW
Max
Unit
IVCC
@ +5.0 V
7
13
20
mA
Negative Supply Current
IVEE
@ −5.2 V
60
78
95
mA
Logic Supply Current
IVDD
@ 3.3 V, without load
8
13
18
mA
Logic Supply Current
IVDD
@ 3.3 V, with load
50
65
80
mA
Positive Supply Voltage
Negative Supply Voltage
Logic Supply Voltage
Power Dissipation
Power Dissipation
Power Supply Sensitivity—VCC
VCC
VEE
VDD
Dual
Dual
Dual
Dual, without load
Dual, with load
4.75
−4.96
2.5
415
5.25
−5.45
5.0
615
675
PSSVCC
5.0
−5.2
3.3
515
575
69
V
V
V
mW
mW
dB
Power Supply Sensitivity—VEE
PSSVEE
85
dB
Power Supply Sensitivity—VDD
PSSVDD
70
dB
NOTE: Under no circumstances should the input voltages exceed the supply voltages.
Rev. 0 | Page 4 of 16
ADCMP567
ABSOLUTE MAXIMUM RATINGS
Table 2. ADCMP567 Absolute Maximum Ratings
Supply
Voltages
Input
Voltages
Output
Temperature
Parameter
Positive Supply Voltage
(VCC to GND)
Negative Supply Voltage
(VEE to GND)
Logic Supply Voltage
(VDD to GND)
Ground Voltage Differential
Input Common-Mode
Voltage
Differential Input Voltage
Input Voltage,
Latch Controls
Output Current
Operating Temperature,
Ambient
Operating Temperature,
Junction
Storage Temperature Range
THERMAL CONSIDERATIONS
Rating
−0.5 V to +6.0 V
−6.0 V to +0.5 V
The ADCMP567 LFCSP 32-lead package option has a θJA
(junction-to-ambient thermal resistance) of 27.2°C/W in
still air.
−0.5 V to +6.0 V
−0.5 V to +0.5 V
−3.0 V to +4.0 V
−7.0 V to +7.0 V
−0.5 V to +5.5 V
30 mA
−40°C to +85°C
125°C
−65°C to +150°C
Stress above those listed under Absolute Maximum Ratings may
cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other
conditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 5 of 16
ADCMP567
QA
QA
VDD
32
31
30
29
28
27
26
25
GND
LEA
LEA
NC
VDD
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
PIN 1
INDICATOR
ADCMP567
TOP VIEW
(Not to Scale)
24
23
22
21
20
19
18
17
VEE
NC
VEE
VCC
VCC
VEE
NC
VEE
GND
LEB
LEB
NC
VDD
QB
QB
VDD
9
10
11
12
13
14
15
16
GND
–INA
+INA
VCC
VCC
+INB
–INB
GND
NC = NO CONNECT
03632-0-002
Figure 2. ADCMP567 Pin Configuration
Table 3. ADCMP567 Pin Descriptions
Pin No.
1
2
Mnemonic
GND
−INA
3
+INA
4
5
6
VCC
VCC
+INB
7
−INB
8
9
10
GND
GND
LEB
11
LEB
12
13
14
NC
VDD
QB
15
QB
16
17
18
19
20
21
VDD
VEE
NC
VEE
VCC
VCC
Function
Analog Ground
Inverting analog input of the differential input stage for Channel A. The inverting A input must be driven
in conjunction with the noninverting A input.
Noninverting analog input of the differential input stage for Channel A. The noninverting A input must
be driven in conjunction with the inverting A input.
Positive Supply Terminal
Positive Supply Terminal
Noninverting analog input of the differential input stage for Channel B. The noninverting B input must
be driven in conjunction with the inverting B input.
Inverting analog input of the differential input stage for Channel B. The inverting B input must be driven
in conjunction with the noninverting B input.
Analog Ground
Analog Ground
One of two complementary inputs for Channel B Latch Enable. In the compare mode (logic low), the
output will track changes at the input of the comparator. In the latch mode (logic high), the output will
reflect the input state just prior to the comparator’s being placed in the latch mode. LEB must be driven
in conjunction with LEB.
One of two complementary inputs for Channel B Latch Enable. In the compare mode (logic high), the
output will track changes at the input of the comparator. In the latch mode (logic low), the output will
reflect the input state just prior to the comparator’s being placed in the latch mode. LEB must be driven
in conjunction with LEB.
No Connect. Leave pin unconnected.
Logic Supply Terminal
One of two complementary outputs for Channel B. QB will be at logic low if the analog voltage at the
noninverting input is greater than the analog voltage at the inverting input (provided the comparator is
in the compare mode). See the LEB description (Pin 11) for more information.
One of two complementary outputs for Channel B. QB will be at logic high if the analog voltage at the
noninverting input is greater than the analog voltage at the inverting input (provided the comparator is
in the compare mode). See the LEB description (Pin 11) for more information.
Logic Supply Terminal
Negative Supply Terminal
No Connect. Leave pin unconnected.
Negative Supply Terminal
Positive Supply Terminal
Positive Supply Terminal
Rev. 0 | Page 6 of 16
ADCMP567
Pin No.
22
23
24
25
26
Mnemonic
VEE
NC
VEE
VDD
QA
27
QA
28
29
30
VDD
NC
LEA
31
LEA
32
GND
Function
Negative Supply Terminal
No Connect. Leave pin unconnected.
Negative Supply Terminal
Logic Supply Terminal
One of two complementary outputs for Channel A. QA will be at logic high if the analog voltage at the
noninverting input is greater than the analog voltage at the inverting input (provided the comparator is
in the compare mode). See the LEA description (Pin 30) for more information.
One of two complementary outputs for Channel A. QA will be at logic low if the analog voltage at the
noninverting input is greater than the analog voltage at the inverting input (provided the comparator is
in the compare mode). See the LEA description (Pin 30) for more information.
Logic Supply Terminal
No Connect. Leave pin unconnected.
One of two complementary inputs for Channel A Latch Enable. In the compare mode (logic high), the
output will track changes at the input of the comparator. In the latch mode (logic low), the output will
reflect the input state just prior to the comparator’s being placed in the latch mode. LEA must be driven
in conjunction with LEA.
One of two complementary inputs for Channel A Latch Enable. In the compare mode (logic low), the
output will track changes at the input of the comparator. In the latch mode (logic high), the output will
reflect the input state just prior to the comparator’s being placed in the latch mode. LEA must be driven
in conjunction with LEA.
Analog Ground
Rev. 0 | Page 7 of 16
ADCMP567
TIMING INFORMATION
LATCH ENABLE
50%
LATCH ENABLE
tS
tPL
tH
DIFFERENTIAL
INPUT VOLTAGE
VIN
VREF ± VOS
VOD
tPDL
tPLOH
Q OUTPUT
50%
tF
tPDH
50%
Q OUTPUT
tPLOL
tR
03633-0-003
Figure 3. System Timing Diagram
The timing diagram in Figure 3 shows the ADCMP567 compare
and latch features. Table 4 describes the terms in the diagram.
Symbol
tH
Timing
Minimum
hold time
tPL
Minimum
latch enable
pulsewidth
Minimum
setup time
Table 4. Timing Descriptions
Symbol
tPDH
Timing
Input to output
high delay
tPDL
Input to output
low delay
tPLOH
Latch enable
to output high
delay
tPLOL
Latch enable
to output low
delay
Description
Propagation delay measured from
the time the input signal crosses
the reference (± the input offset
voltage) to the 50% point of an
output low-to-high transition
Propagation delay measured from
the time the input signal crosses
the reference (± the input offset
voltage) to the 50% point of an
output high-to-low transition
Propagation delay measured from
the 50% point of the Latch Enable
signal low-to-high transition to
the 50% point of an output lowto-high transition
Propagation delay measured from
the 50% point of the Latch Enable
signal low-to-high transition to
the 50% point of an output highto-low transition
tS
tR
Output rise
time
tF
Output fall
time
VOD
Voltage
overdrive
Rev. 0 | Page 8 of 16
Description
Minimum time after the negative
transition of the Latch Enable
signal that the input signal must
remain unchanged to be acquired
and held at the outputs
Minimum time that the Latch
Enable signal must be high to
acquire an input signal change
Minimum time before the
negative transition of the Latch
Enable signal that an input signal
change must be present to be
acquired and held at the outputs
Amount of time required to
transition from a low to a high
output as measured at the 20%
and 80% points
Amount of time required to
transition from a high to a low
output as measured at the 20%
and 80% points
Difference between the
differential input and reference
input voltages
ADCMP567
APPLICATION INFORMATION
The ADCMP567 comparators are very high speed devices.
Consequently, high speed design techniques must be employed
to achieve the best performance. The most critical aspect of any
ADCMP567 design is the use of a low impedance ground plane.
A ground plane, as part of a multilayer board, is recommended
for proper high speed performance. Using a continuous conductive plane over the surface of the circuit board can create
this, allowing breaks in the plane only for necessary signal
paths. The ground plane provides a low inductance ground,
eliminating any potential differences at different ground points
throughout the circuit board caused by ground bounce. A
proper ground plane also minimizes the effects of stray
capacitance on the circuit board.
It is also important to provide bypass capacitors for the power
supply in a high speed application. A 1 µF electrolytic bypass
capacitor should be placed within 0.5 inches of each power
supply pin to ground. These capacitors will reduce any potential
voltage ripples from the power supply. In addition, a 10 nF
ceramic capacitor should be placed as close as possible from the
power supply pins on the ADCMP567 to ground. These
capacitors act as a charge reservoir for the device during high
frequency switching.
The LATCH ENABLE input is active low (latched). If the
latching function is not used, the LATCH ENABLE input
should be attached to VDD (VDD is a PECL logic high), and the
complementary input, LATCH ENABLE, should be tied to
VDD − 2.0 V. This will disable the latching function.
Occasionally, one of the two comparator stages within the
ADCMP567 will not be used. The inputs of the unused
comparator should not be allowed to float. The high internal
gain may cause the output to oscillate (possibly affecting the
comparator that is being used) unless the output is forced into a
fixed state. This is easily accomplished by ensuring that the two
inputs are at least one diode drop apart, while also appropriately
connecting the LATCH ENABLE and LATCH ENABLE inputs
as described above.
The best performance is achieved with the use of proper PECL
terminations. The open emitter outputs of the ADCMP567 are
designed to be terminated through 50 Ω resistors to VDD −2.0 V,
or any other equivalent PECL termination. If high speed PECL
signals must be routed more than a centimeter, microstrip or
stripline techniques may be required to ensure proper transition
times and prevent output ringing.
CLOCK TIMING RECOVERY
Comparators are often used in digital systems to recover clock
timing signals. High speed square waves transmitted over a
distance, even tens of centimeters, can become distorted due to
stray capacitance and inductance. Poor layout or improper
termination can also cause reflections on the transmission line,
further distorting the signal waveform. A high speed
comparator can be used to recover the distorted waveform
while maintaining a minimum of delay.
OPTIMIZING HIGH SPEED PERFORMANCE
As with any high speed comparator amplifier, proper design and
layout techniques should be used to ensure optimal performance from the ADCMP567. The performance limits of high
speed circuitry can easily be a result of stray capacitance,
improper ground impedance, or other layout issues.
Minimizing resistance from source to the input is an important
consideration in maximizing the high speed operation of the
ADCMP567. Source resistance in combination with equivalent
input capacitance could cause a lagged response at the input,
thus delaying the output. The input capacitance of the
ADCMP567 in combination with stray capacitance from an
input pin to ground could result in several picofarads of
equivalent capacitance. A combination of 3 kΩ source resistance
and 5 pF of input capacitance yields a time constant of 15 ns,
which is significantly slower than the sub 500 ps capability of
the ADCMP567. Source impedances should be significantly less
than 100 Ω for best performance.
Sockets should be avoided due to stray capacitance and inductance. If proper high speed techniques are used, the ADCMP567
should be free from oscillation when the comparator input
signal passes through the switching threshold.
COMPARATOR PROPAGATION
DELAY DISPERSION
The ADCMP567 has been specifically designed to reduce
propagation delay dispersion over an input overdrive range of
100 mV to 1 V. Propagation delay overdrive dispersion is the
change in propagation delay that results from a change in the
degree of overdrive (how far the switching point is exceeded by
the input). The overall result is a higher degree of timing
accuracy since the ADCMP567 is far less sensitive to input
variations than most comparator designs.
Propagation delay dispersion is a specification that is important
in critical timing applications such as ATE, bench instruments,
and nuclear instrumentation. Overdrive dispersion is defined
Rev. 0 | Page 9 of 16
ADCMP567
as the variation in propagation delay as the input overdrive
conditions are changed (Figure 4). For the ADCMP567,
overdrive dispersion is typically 35 ps as the overdrive is
changed from 100 mV to 1 V. This specification applies for
both positive and negative overdrive since the ADCMP567 has
equal delays for positive and negative going inputs.
–VH
2
+VH
2
0V
INPUT
1
The 35 ps propagation delay overdrive dispersion of the
ADCMP567 offers considerable improvement of the 100 ps
dispersion of other similar series comparators.
0
1.5V OVERDRIVE
OUTPUT
INPUT VOLTAGE
20mV OVERDRIVE
03633-0-005
VREF ± VOS
Figure 5. Comparator Hysteresis Transfer Function
60
DISPERSION
Q OUTPUT
50
03633-0-004
The addition of hysteresis to a comparator is often useful in a
noisy environment or where it is not desirable for the comparator to toggle between states when the input signal is at the
switching threshold. The transfer function for a comparator
with hysteresis is shown in Figure 5. If the input voltage
approaches the threshold from the negative direction, the
comparator will switch from a 0 to a 1 when the input crosses
+VH/2. The new switching threshold becomes −VH/2. The
comparator will remain in a 1 state until the threshold −VH/2 is
crossed coming from the positive direction. In this manner,
noise centered on 0 V input will not cause the comparator to
switch states unless it exceeds the region bounded by ±VH/2.
Positive feedback from the output to the input is often used to
produce hysteresis in a comparator (Figure 9). The major
problem with this approach is that the amount of hysteresis
varies with the output logic levels, resulting in a hysteresis that
is not symmetrical around zero.
Another method to implement hysteresis is generated by
introducing a differential voltage between LATCH ENABLE
and LATCH ENABLE. inputs (Figure 10). Hysteresis generated
in this manner is independent of output swing and is symmetrical around zero. The variation of hysteresis with input voltage is
shown in Figure 6.
40
30
20
10
0
–25
–20
–15
–10
–5
∆ LATCH = LE – LEB (mV)
0
5
03632-0-006
COMPARATOR HYSTERESIS
HYSTERESIS (mV)
Figure 4. Propagation Delay Dispersion
Figure 6. Comparator Hysteresis Transfer Function
Using Latch Enable Input
MINIMUM INPUT SLEW RATE REQUIREMENT
As for all high speed comparators, a minimum slew rate must
be met to ensure that the device does not oscillate when the
input crosses the threshold. This oscillation is due in part to the
high input bandwidth of the comparator and the parasitics of
the package. Analog Devices recommends a slew rate of 5 V/µs
or faster to ensure a clean output transition. If slew rates less
than 5 V/µs are used, then hysteresis should be added to reduce
the oscillation.
Rev. 0 | Page 10 of 16
ADCMP567
TYPICAL APPLICATION CIRCUITS
VIN
VIN
ADCMP567
ADCMP567
OUTPUTS
OUTPUTS
VREF
LATCH
ENABLE
INPUTS
HYSTERESIS
VOLTAGE
VDD – 2V
VDD – 2V
450Ω
ALL RESISTORS 50Ω
ALL RESISTORS 50Ω UNLESS OTHERWISE NOTED
03632-0-007
03632-0-010
Figure 7. High Speed Sampling Circuits
Figure 10. Hysteresis Using Latch Enable Input
+VREF
ADCMP567
OUTPUTS
VIN
VIN
ADCMP567
100Ω
50Ω
50Ω
50Ω
50Ω
100Ω
(VDD – 2) × 2
03632-0-011
Figure 11. How to Interface a PECL Output to an
Instrument with a 50 Ω to Ground Input
ADCMP567
–VREF
LATCH
ENABLE
INPUTS
VDD – 2V
ALL RESISTORS 50Ω
03632-0-008
Figure 8. High Speed Window Comparator
VIN
ADCMP567
VREF
R1
OUTPUTS
R2
VDD – 2V
ALL RESISTORS 50Ω
03632-0-009
Figure 9. Hysteresis Using Positive Feedback
Rev. 0 | Page 11 of 16
ADCMP567
TYPICAL PERFORMANCE CHARACTERISTICS
(VCC = +5.0 V, VEE = −5.2 V, VDD = +3.3 V, TA = 25°C, unless otherwise noted.)
23.0
30
22.9
+IN INPUT BIAS CURRENT (µA)
(+IN = 1V, –IN = 0V)
INPUT BIAS CURRENT (µA)
25
20
15
10
5
22.8
22.7
22.6
22.5
22.4
22.3
22.2
22.0
–40
–20
0
20
40
TEMPERATURE (°C)
60
80
03632-0-016
0
–2.5
–1.5
–0.5
0.5
1.5
2.5
3.5
NONINVERTING INPUT VOLTAGE (INVERTING VOLTAGE = 0.5V)
03632-0-013
22.1
Figure 15. Input Bias Current vs. Temperature
Figure 12. Input Bias Current vs. Input Voltage
60
2.0
1.8
50
1.4
HYSTERESIS (mV)
OFFSET VOLTAGE (mV)
1.6
1.2
1.0
0.8
0.6
0.4
40
30
20
10
20
40
TEMPERATURE (°C)
60
80
0
–25
195
185
185
175
175
TIME (ps)
195
165
155
135
135
10 20 30 40 50
TEMPERATURE (°C)
60
70
5
90
155
145
0
0
165
145
125
–40 –30 –20 –10
–15
–10
5
∆ LATCH = LE – LEB (mV)
Figure 16. Hysteresis vs. ∆Latch
80
90
03632-0-015
TIME (ps)
Figure 13. Input Offset Voltage vs. Temperature
–20
03632-0-017
0
–20
03632-0-014
0
–40
03632-0-018
0.2
Figure 14. Rise Time vs. Temperature
125
–40 –30 –20 –10
0
10 20 30 40 50
TEMPERATURE (°C)
60
Figure 17. Fall Time vs. Temperature
Rev. 0 | Page 12 of 16
70
80
240
236
238
235
236
PROPAGATION DELAY (ps)
234
232
230
228
234
233
232
231
230
224
–40 –30 –20 –10
0
10 20 30 40 50
TEMPERATURE (°C)
60
70
80
90
03632-0-019
226
229
–2
Figure 18. Propagation Delay vs. Temperature
–1
0
1
2
INPUT COMMON-MODE VOLTAGE (V)
3
03632-0-022
PROPAGATION DELAY (ps)
ADCMP567
Figure 21. Propagation Delay vs. Common-Mode Voltage
0
60
30
20
10
0
0
0.2
0.4
0.6
0.8
1.0
1.2
OVERDRIVE VOLTAGE (V)
1.4
1.6
Figure 19. Propagation Delay Error vs. Overdrive Voltage
2.1
1.9
1.7
1.5
1.2
1.3
1.4
1.5
1.6
TIME (ns)
1.7
1.8
1.9
2.0
03632-0-021
OUTPUT RISE AND FALL (V)
2.3
1.1
–15
–20
–25
–30
–35
–40
0.15
2.15
4.15
6.15
PULSEWIDTH (ns)
8.15
Figure 22. Propagation Delay Error vs. Pulsewidth
2.5
1.3
1.0
–10
Figure 20. Rise and Fall of Outputs vs. Time
Rev. 0 | Page 13 of 16
03632-0-023
PROPAGATION DELAY ERROR (ps)
40
03632-0-020
PROPAGATION DELAY ERROR (ps)
–5
50
ADCMP567
OUTLINE DIMENSIONS
5.00
BSC SQ
0.60 MAX
0.60 MAX
PIN 1
INDICATOR
25
24
PIN 1
INDICATOR
0.50
BSC
4.75
BSC SQ
TOP
VIEW
0.50
0.40
0.30
3.25
2.70 SQ
1.25
BOTTOM
VIEW
17
16
9
8
3.50
REF
0.80 MAX
0.65 NOM
12° MAX
32 1
0.05 MAX
0.02 NOM
1.00
0.90
0.80
SEATING
PLANE
0.30
0.23
0.18
0.20 REF
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2
Figure 23. 32-Lead Lead Frame Chip Scale Package [LFCSP]
(CP-32)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADCMP567BCP
Temperature Range
−40°C to +85°C
Package Description
LFCSP-32
Rev. 0 | Page 14 of 16
Package Option
CP-32
ADCMP567
Notes
Rev. 0 | Page 15 of 16
ADCMP567
Notes
© 2003 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C03632–0–10/03(0)
Rev. 0 | Page 16 of 16
Filename:
ADCMP567_Oct 21.doc
Directory:
C:\Documents and Settings\fburns\Desktop
Template:
C:\Documents and Settings\aakers\Desktop\Data Sheet Template v3.2.dot
Title:
ADCMP567 Dual Ultrafast Voltage Comparator Data Sheet (REV. 0)
Subject:
Author:
Analog Devices, Inc.
Keywords:
Comments:
Creation Date:
10/15/2003 1:35 PM
Change Number:
15
Last Saved On:
10/21/2003 4:57 PM
Last Saved By:
Frumie Burns
Total Editing Time:
77 Minutes
Last Printed On:
10/21/2003 4:58 PM
As of Last Complete Printing
Number of Pages:
16
Number of Words:
4,011 (approx.)
Number of Characters: 20,422 (approx.)